Transcript
Installation
Installation/user guide
Location
TYXIA 442
The receiver must be fitted on a flush-mounted box (Ø 65 mm) that will receive the lighting’s live and neutral wires.
Receiver switch
DELTA DORE Bonnemain - 35270 COMBOURG - France E-mail :
[email protected]
Device complying with the requirements of the R&TTE 1999/5/EC directives
*2701914_rev1*
Lighting dimmer receiver
Because of changes in standards and equipment, the characteristics given in the text and the illustrations of this document are not binding unless confirmed by Delta Dore.
Warnings • Carefully read these instructions prior to installation. • The unit must be installed in compliance with currently applicable standards. • Always switch off the mains before installing or servicing the unit. • Do not attempt to repair the unit yourself; an after-sales service is available. • Check that the fastenings are suited to the surface that the unit will be attached to (plasterboard, brick, etc.). • The diagrams provided are simplified for greater clarity. The protective units and other accessories required by the standards are not illustrated. Standard UTE NF C15-100 and good practice must be complied with. Connected or nearby equipment must not generate excessive interference (directive 2004/108/EEC).
Your unit comes with a plastic protection that must be removed when work is complete (for example after painting), before replacing the cover plate (Delta Dore brand located in the lower right).
Plastic protection
Connecting and mounting the product Connect the product, then position it by orienting the terminal upwards. Secure it by tightening the screws without forcing them.
Connection
Operating the TYXIA 442
Switch off the mains power supply (general circuit breaker) before any intervention.
The buttons and enable the brightness of the lighting to be adjusted.
TYXIA 442
If the lighting is off Press briefly
L
Return to the last setting (e.g. 70%)
50 W min. 240 W max. N 230 V L 50 Hz
The dimmer is compatible with: the incandescent lamps ( halogen lamps (
Press briefly a 2nd time Press and hold
100% lighting
Dimmer
) and the 230 V
).
If the lighting is on
The dimmer is incompatible with: fluorescent lamps, motors, low-consumption lamps, halogen lamps with electronic transformers, and 230 V halogen lamps with TBT ferromagnetic transformer.
Press briefly Press and hold
Lighting is turned off
Dimmer
Operation associated with a TYXIA Transmitter The TYXIA 442 receiver can be associated with the buttons of a TYXIA transmitter (transmitter switch, key ring remote control, etc.). Each receiver can record up to a maximum of 8 associations (buttons, transmitters, etc.).
OR Last setting (if lights off)
Lighting off (if lighting on)
Same operation as the dimmer control with TYXIA 442
Associating a
button
Associating
Associating a
buttons
On the receiver, simultaneously press the buttons and until they flash (~3 seconds).
On the receiver, simultaneously press the buttons and until they flash (~3 seconds).
One button (scenario) can control different receivers simultaneously (roller blinds, dimmer, simple lighting, etc.).
On the transmitter, press and hold the button down for approximately 5 seconds. The LED will light up, go out, then light up again. Release. Check that the receiver’s LED is no longer flashing.
On the transmitter, press and hold the
On the receiver, set the appliance to the required status (e.g. subdued light, then simultaneously press the buttons and until the LED flashes (~3 seconds).
The transmitter with the receiver.
button is associated
and buttons for approximately 5 seconds, until the LED comes on. Release. Check that the receiver’s LED is no longer flashing. The transmitter buttons and associated with the receiver.
are
TYDOM 310 telephone transmitter TYDOM 310 enables the ON/OFF feature to be operated remotely.
TYDOM 200 multifunction remote control TYDOM 200 includes all the functions of the TYXIA buttons:
To associate TYXIA 442 with the TYDOM 200 or TYDOM 310, please refer to the respective guides.
On the transmitter, press and hold the button down for approximately 5 seconds. The LED will light up, go out, then light up again. Release. Check that the receiver’s LED is no longer flashing.
Setting (scenario) is defined when associating the button with the receiver (e.g. subdued lighting)
Operation with an associated TYDOM transmitter
button (scenario)
The transmitter with the receiver.
Removing all the receiver associations Press and hold the receiver buttons and (after 3 seconds, the LED flashes). Hold the buttons down until the LED extinguishes to confirm that all the receiver associations are removed.
Technical characteristics • 230 V, 50 Hz power supply, +/-10% • Class II insulation • Power consumption: 1 VA • Incandescent lamps and halogen lamps: 50 W minimum to 240 W max, Cos XXX = 1 • Radio frequency 868 MHz (standard EN 300 220) • Radio range: 100 to 300 metres outside depending on the equipment associated (the range can be altered depending on the installation conditions and the electromagnetic environment) • Number of transmitters that can be associated with a button on the receiver: 8 max. • Operating temperature: 0 to +40°C • Storage temperature: -10 to +70°C • Dimensions: 80 x 80 mm, height 45 mm • Protection index: IP 40 - IK 04 • Installation in an environment with normal pollution levels
button is associated
Maintenance Diagnosis /Solutions You cannot associate a transmitter with your receiver
The maximum number of transmitters that can be associated with a receiver button is 8. If this number is reached, the LED flashes. To exit this mode, press and hold down the receiver button for 3 seconds.
The receiver • The transmitter is not associated does not with the receiver. recognize • The receiver is still in association the command mode. from a • The transmitter batteries are flat. transmitter: The lighting intensity does not reach the maximum threshold
The power controlled is too high; the receiver is in thermal security mode. Wait for 1 hour before repeating the test, or check that the controlled power is not greater than 250W.
