Transcript
T1-US2DS01
Installation Guide
Introduction T1-US2DS01 is an eSATA & USB 2.0 Combo to Dual SATA RAID storage enclosure. It provides two hot-swappable 3.5" HDD mobile trays for easy installation and un-installation. T1-US2DS01 is a hardware RAID enclosure, requiring no software installation on the user’s machine. The user can select different RAID modes for the two 3.5" SATA HDDs. You can configure the T1-US2DS01 to use the following Storage Policies to map its appliance's physical hard drives to virtual drives that are visible to the host computer. * BIG (Concatenation) * JBOD (Just a Bunch Of Disks) * FAST (RAID 0) * SAFE (RAID 1) * SAFE33 (1/3 to SAFE mode and 2/3 to BIG mode) * SAFE50 (1/2 to SAFE mode and 1/2 to BIG mode) * GUI (Use the SteelVine Manager GUI to configure the Storage Policy)
Overview Front Panel
Back Panel
3-1
1
2-1
3-2
4 5
8
6
2-2
1. Lock Screw 2. 3.5” SATA Mobile Tray 2-1. Drive 1 2-2. Drive 2 3. Device LED 3-1. Drive 1 3-2. Drive 2 4. Power LED (Green) 5. Alarm LED (Red)
7
6. AC Input AC 100~240V, 47~63Hz, 72W 7. Power On/OFF 8. Cooling Fan 9. eSATA Connector 10. Host Status LEDs 11. Change Mode Button
11 12
9 10
15
13 14 16
12. Rotary switch 13. USB Host LED 14. USB B Type Connector 15. Alarm LED 16. Power LED
Rotary switch & Change Mode Button
LEDs Device LED (ACT & Link) : DISK 1
DISK 2
Link Activity (Green) (Red)
Link Activity (Green) (Red)
LEDs on JBOD Mode Description Device Unplugged/No power Device Plugged (Idle) Device Plugged (Activity) LEDs on RAID Mode Description Device Unplugged/No power Device Plugged (Idle) Device Plugged (Activity) Disk Rebuild (A Physical Partition is being Rebuilt;Safe Mode(RAID 1)) Disk Rebuild-Verify (A Physical Partition is being Verified; Safe Mode (RAID1))
You can configure the T1-US2DS01 to use the following Storage Policies to map its appliance's physical hard drives to virtual drives that are visible to the host computer.
Red(ACT) Off Off Flash (On)
Green(Link) Off On On
ACT Blink Off Flash (On)
Link Blink On On
On
Blink
Flash (On) will appear as On
On
Alarm LED: (Red LED) Volume degradation (RAID 1) or unavailability (JBOD, Big, Fast) will be marked by turning on the Alarm LED and the alarm Buzzer for the node that experienced this behavior. RAID 1 Status LED
Normal
Error
OFF
ON
- BIG (Concatenation) - JBOD (Just a Bunch Of Disks) - FAST (RAID 0) - SAFE (RAID 1) - SAFE33 (1/3 to SAFE mode and 2/3 to BIG mode) - SAFE50 (1/2 to SAFE mode and 1/2 to BIG mode) - GUI (Use the SteelVine Manager GUI to configure the Storage Policy)
Rotary switch: To select a storage policy in this mode the first time that a new factory-shipped product is used, ensure that the hard disk drives are installed, set the rotary switch on the back of the T1-US2DS01 to the desired Storage Policy (not the GUI selection) and turn on the power. Change Mode Button: To2change the storage policy thereafter, set the rotary . to the desired position and press the recessed switch Change Mode Button to create the new virtual volume(s). Creating new virtual volumes will destroy any existing data that existed on the previous volume, but expanding an existing BIG volume will not destroy any existing data.
Power LED: (Green LED)
QL.NB278.12
T1-US2DS01
Installation Guide
Installing Hard Disk Drive 1. Unscrew the Lock screw on the Mobile Tray.
6. Replace the Lock screw on the Mobile Tray.
7. Attach the Power Cable Note: Input : AC 100~240V, 47~63Hz
2. To remove the Mobile Tray, hold the mobile tray firmly and gently pull out the tray from the housing.
Applications 1. For desktop use T1 can stand up vertically with foot stands.
3. To install a SATA HDD, simply place the HDD inside the tray as illustrated below. (A stopper in the rear of the tray is provided to ensure proper alignment)
Stick 4 Rubbers on foot stand
2. For rack mount Two T1 can be linked together with four fixed brackets. 4. After placing the HDD inside the tray, secure the HDD with four screws
5. To insert the tray, hold the mobile tray firmly and push it back into the housing.
QL.NB272.12
