Transcript
OPERATION MANUAL UFH-70DDA Digital Distribution Amplifier 1st Edition
Precautions Important Safety Warnings [Power]
Stop
Do not place or drop heavy or sharp-edged objects on power cord. A damaged cord can cause fire or electrical shock hazards. Regularly check power cord for excessive wear or damage to avoid possible fire / electrical hazards.
[Circuitry Access]
Stop
Do not touch any parts / circuitry with a high heat factor. Capacitors can retain enough electric charge to cause mild to serious shock, even after power is disconnected. Capacitors associated with the power supply are especially hazardous. Avoid contact with any capacitors.
Hazard
Unit should not be operated or stored with cover, panels, and / or casing removed. Operating unit with circuitry exposed could result in electric shock / fire hazards or unit malfunction.
[Potential Hazards]
Caution
If abnormal smells or noises are noticed coming from the unit, turn power off immediately and disconnect power cord to avoid potentially hazardous conditions. If problems similar to above occur, contact authorized service representative before attempting to again operate unit.
[Consumables]
Caution
The consumables used in unit must be replaced periodically. For further details on which parts are consumables and when they should be replaced, refer to the specifications at the end of the Operation Manual. Since the service life of the consumables varies greatly depending on the environment in which they are used, they should be replaced at an early date. For details on replacing the consumables, contact your dealer.
Upon Receipt Unpacking UFH-70DDA units and their accessories are fully inspected and adjusted prior to shipment. Operation can be performed immediately upon completing all required connections and operational settings. Check your received items against the packing lists below. ITEM UFH-70DDA Operation Manual
QTY 1 1
REMARKS (This manual)
Check Check to ensure no damage has occurred during shipment. If damage has occurred, or items are missing, inform your supplier immediately.
Table of Contents 1. Prior to Starting ...........................................................................................................................1 1-1. Welcome .............................................................................................................................1 1-2. Features..............................................................................................................................1 1-3. About This Manual ..............................................................................................................1 2. Panel Descriptions ......................................................................................................................2 2-1. Front Panel .........................................................................................................................2 2-2. Rear Panel..........................................................................................................................2 2-3. Mode Setting.......................................................................................................................3 3. Connection..................................................................................................................................4 3-1. Connection Example...........................................................................................................4 4. Operation ....................................................................................................................................5 4-1. Power ON ...........................................................................................................................5 5. Specifications and Dimensions ...................................................................................................6 5-1. Unit Specifications...............................................................................................................6 5-2. External Dimensions ...........................................................................................................7
1. Prior to Starting 1-1. Welcome Congratulations! By purchasing UFH-70DDA Digital Distribution Amplifier you have entered the world of FOR-A and its many innovative products. Thank you for your patronage and we hope you will turn to FOR-A products again and again to satisfy your video and audio needs. FOR-A provides a wide range of products, from basic support units to complex system controllers, which have been increasingly joined by products for computer video based systems. Whatever your needs, talk to your FOR-A representative. We will do our best to be of continuing service to you.
1-2. Features The UFH-70DDA System Frame module is a signal distribution amplifier for FOR-A System Frames with 1-input/7-output distribution of serial digital component signals in both SD and HD. Installable to FOR-A System Frames (UFH-108/108A or UFH-112/112A) Accepts and distributes digital component signals in both SD and HD. (Auto switching) Cable compensation function allows the input-side cable length to be as long as 200 meters when BNC 5C-2V, RG-11A/U or equivalent cable used for SD SDI, and 100 meters when BNC 5C-FB, RG-59B/U or equivalent cable used for HD SDI. Reclock function to minimize signal jitters. HD and SD Input Signal Auto Detection / Auto Switching Supports DVB-ASI signals by changing internal setting.
1-3. About This Manual This manual is intended to help the user easily operate this product and make full use of its functions during operations. Before connecting or operating your unit, read this operation manual thoroughly to ensure you understand the product. After reading, it is important to keep this manual in a safe place and available for reference.
1
2. Panel Descriptions 2-1. Front Panel (5)
POWER
INPUT
A
HD
DVB-ASI
INPUT
B (OPTION) HD
(OPTION) INTERFACE
DVB-ASI
UFH-70DDA
UFH-70DDA
(1)
(1)
POWER Indicator
(2) (3) (4) (5) (6)
(2) (3)
INPUT A
HD
DVB-ASI B (OPTION) INTERFACE
(4)
(6)
Power indicator lights green whenever power is applied to the unit. Indicator lights whenever an HD or SD serial digital signal is inputted to the unit. Indicator lights whenever an HD serial digital signal is inputted to the unit. Indicator lights whenever the system operates in DVB-ASI mode. Not used. Not used.
2-2. Rear Panel HD/SD
HD/SD 1
HD/SD 2
HD/SD 3
VIDEO IN
VIDEO OUT
(1)
(1)
VIDEO IN
(2)
VIDEO OUT
HD/SD 4
HD/SD 5
HD/SD 6
HD/SD 7
UFH-70DDA
(2)
Used for serial digital component video (HD/SD SDI) input connection. Used for serial digital component video (HD/SD SDI) output connection. The unit distributes the input signal to seven identical outputs.
2
2-3. Mode Setting The unit has two operation modes: SD/HD SDI mode and DVB-ASI mode. The SD/HD SDI mode is set at the factory shipping. To switch the operation mode of the unit, change the mode switch on the rear module board as shown in the figure below.
ＵＦＨ-70ＤＤＡ rear module
VIDEO
Switch Setting VIDEO side DVB side
Operation Mode SD/HD SDI (default) DVB-ASI
DVB
The mode setting must be done before installing the rear module to the System Frame and inputting DVB-ASI signal. The DVB-ASI indicator on the front panel will glow when switching to DVB-ASI mode.
3
3. Connection Note that before installing UFH-70DDA into the System Frame you should thoroughly read the operation manual for the System Frame you will be installing to. IMPORTANT When installing module boards, keep boards in their insulated packet until just prior to installation to avoid static electricity problems. Also, do not touch board components for the same reason.
3-1. Connection Example Connect the unit to other equipment in the total system as shown in the figure below.
UFH-112A HD SDI signal or SD SDI signal
HD/SD SDI IN
HD/SD OUT 1 HD/SD OUT 2 HD/SD OUT 3
UFH-70DDA
HD/SD OUT 4 HD/SD OUT 5 HD/SD OUT 6 HD/SD OUT 7
4
HD SDI signal or SD SDI signal
4. Operation 4-1. Power ON 1) Loosen the two knob screws on the front panel face of the System Frame, and then grasp the knob screws to pull them out.
POWER 1
GENLOCK 1 2
FAN
ALARM TEMP DC POW
UFH-112
SYSTEM FRAME
POWER 2
GENLOCK 1 2
FAN
ALARM TEMP DC POW
2) Turn the power switch(es) ON.
5
5. Specifications and Dimensions 5-1. Unit Specifications Video Input
HD SDI 1.485/1.001Gbps, SD SDI 143Mbps - 270Mbps, or DVB-ASI 270Mbps, 75Ω BNC 1 input
Video Output
HD SDI 1.485/1.001Gbps, SD SDI 143Mbps to 270Mbps, or DVB-ASI 270Mbps, 75Ω BNC 7 outputs
Cable Length Compensation
0m to 100m when 5C-FB, RG-59B/U or equivalent cable used for HD SDI. 0m to 200m when 5C-2V, RG-11A/U or equivqlent cable used for SD SDI.
Temperature
10°C - 40°C
Humidity
30% - 90% (no condensation)
Power
+ 24VDC (supplied from System Frame)
Power Consumption
4.6VA (4.6W)
Dimensions
Front module：138.5 (W) x 400 (D) mm Rear module：141 (W) x 101 (D) mm
Weight
1.0 kg
Required Slot
1 slot
6
5-2. External Dimensions (All dimensions in mm.)
141
VIDEO IN
U FH -7 0D D A
VIDEO OUT
20
HD/S D
87.8
(101)
379.5
(400)
HD/S D 1
HD/SD 2
HD/SD 3
HD/S D 4
HD/SD 5
HD/SD 6
HD/SD 7
EXTENTION CARD(Option) I/F CARD (Option) POWER
A IN PU T
HD
B (OPTION) DV B-ASI
INPU T
HD
DV B-ASI
( OP TION) IN TE RFAC E UFH- 70DD A
UF H-70 DDA
7
Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
09/29/2009 Printed in Japan
FOR-A COMPANY LIMITED Head Office Overseas Division Japan Branch Offices R&D/Production
: 3-8-1 Ebisu, Shibuya-ku, Tokyo 150-0013, Japan Phone: +81 (0)3-3446-3936, Fax: +81 (0)3-3446-1470 : Osaka/Okinawa/Fukuoka/Hiroshima/Nagoya/Sendai/Sapporo : Sakura Center/Sapporo Center
FOR-A America Corporate Office 11125 Knott Ave., Suite #A, Cypress, CA 90630, USA Phone: +1 714-894-3311 Fax: +1 714-894-5399
FOR-A America East Coast Office Two Executive Drive, Suite 670, Fort Lee Executive Park, Fort Lee NJ 07024, USA Phone: +1 (201) 944-1120 Fax : +1 (201) 944-1132
FOR-A America Distribution & Service Center 2400 N.E. Waldo Road, Gainesville, FL 32609, USA Phone: +1 352-371-1505 Fax: +1 352-378-5320
FOR-A Corporation of Canada 346A Queen Street West, Toronto, Ontario M5V 2A2, Canada Phone: +1 416-977-0343 Fax: +1 416-977-0657
FOR-A Latin America & the Caribbean 5200 Blue lagoon Drive, Suite 760, Miami, FL 33126, USA Phone: +1-305-931-1700 Fax: +1-305-264-7890
FOR-A UK Limited UNIT C71, Barwell Business Park, Leatherhead Road, Chessington Surrey, KT9 2NY, UK Phone: +44 (0)20-8391-7979 Fax: +44 (0)20-8391-7978
FOR-A Italia S.r.l. Viale Europa 50 20093, Cologno Monzese (MI), Milan, Italy Phone: +39 02-254-3635/6 Fax: +39 02-254-0477
FOR-A Corporation of Korea 801 Dangsan Bld., 53-1 Dangsan-Dong, Youngdeungpo-Gu, Seoul 150-800, Korea Phone: +82 (0)2-2637-0761 Fax: +82 (0)2-2637-0760
FOR-A China Limited 708B Huateng Building, No. 302, 3 District, Jinsong, Chaoyang, Beijing 100021, China Phone: +86 (0)10-8721-6023 Fax: +86 (0)10-8721-6033
*The contents of this manual are subject to change without notice.
