Transcript
Installation Guide M.2 Installation Steps 2
Plastic Mounting Board
80 mm
1
M.2 Card
60 mm 42 mm
22x80 mm
Mounted Standard L bracket Screws and washer for mounting M.2 card to PCB
22x60 mm
Screws for mounting PCB to Plastic Mounting Board PCB
Screws for mounting PCB to Plastic Mounting Board to 3.5” or 5.25” or custom mounting
22x42 mm
M.2 card comes in different length and
1. Verify the package contents.
2. sizes (42, 60, 80mm), match your M.2 card length to the hole alignment to decide which mounting hole to use.
M.2 Card by inserting the M.2 Card and secure using the 2. Attached washer and screw to hold the M.2 card in place.
The device is ready to be
3. integrated into your system.
mSATA Installation Steps IMPORTANT NOTE: UGT-MST210 card will only support 50mm & 27mm card length. Plastic Mounting Board
2
1
mSATA card
70 mm 50 mm 27 mm
70 mm
Mounted Standard L bracket Screws and washer for mounting M.2 card to PCB Screws for mounting PCB to Plastic Mounting Board PCB
Screws for mounting PCB to Plastic Mounting Board to 3.5” or 5.25” or custom mounting
1. Verify the package contents.
Information in this document is subject to change without notice. Reproduction of these materials in any manner whatsoever without written permission is strictly forbidden. Printed in China Printed on Recycled Paper.
50 mm
27 mm
mSATA card comes in different sizes
2. (27, 50, or 70mm), match your mSATA
card size to the hole alignment to decide which mounting hole or clip to use.
mSATA Device by inserting the mSATA Card and 2. Attached securing the using the latch to lock or using the washer and screw
The device is ready to be
3. integrated into your system.
to hold the mSATA card in place.
Model: UGT-MST110, UGT-MST210, UGT-M2ST120, UGT-M2S220
www.vantecusa.com
Copyright © 2016 Vantec Thermal Technologies. All Right Reserved.
|
All Registered Trademarks Belong To Their Respective Companies.
Installation Guide Mounted Standard L bracket
a)
3.5” Drive Bay
Mounted Standard L bracket
Screws for mounting PCB to Plastic Mounting Board
b)
c)
Screws for mounting Plastic Mounting Board to 3.5” or 5.25” or custom mounting
5.25” Drive Bay 3.5” Drive Bay
www.vantecusa.com
3.5” Drive Bay
1. Mount using Standard L bracket. a) The card comes mounted on a Standard L bracket, nothing need to be done.
2. Mounting into 3.5” Drive Bay.
3. Mounting into 5.25” Drive Bay.
a) Remove the two screws holding the Standard L bracket.
(Optional accessories may be required depending on the design of your 5.25” Drive Bay)
b) Secure the PCB to the Plastic Mounting plate. Align the 4 stand off to the mounting hole with the 4provided screws as shown,
a) Remove the two screws holding the Standard L bracket.
c) Secure the Plastic Mounting Plate to the 3.5” Drive Bay using the provided 4 screws.
b) Secure the PCB to the Plastic Mounting plate. Align the 4 stand off to the mounting hole with the 4 provided screws as shown.
4. Custom Mounting. a) Please refer to the technical drawing on our website product page for detail measurement of the mounting.
c) If your 5.25" Drive Bay have the necessary screws hole to secure a 2.5" HDD, you can secure this Plastic Mounting Board (with the PCB mounted) to this 5.25" Drive Bay. d) If your 5.25" Drive Bay do not have the necessary screws hole to secure a 2.5" HDD, you will need to secure this Plastic Mounting Board (with the PCB mounted) to a 3.5" Drive Bay kit before securing to the 5.25" Drive Bay.
Information in this document is subject to change without notice. Reproduction of these materials in any manner whatsoever without written permission is strictly forbidden. Printed in China Printed on Recycled Paper.
Model: UGT-MST110, UGT-MST210, UGT-M2ST120, UGT-M2S220
www.vantecusa.com
Copyright © 2016 Vantec Thermal Technologies. All Right Reserved.
|
All Registered Trademarks Belong To Their Respective Companies.
UGT-MST210
