Transcript
HCD-EP313 SERVICE MANUAL
US Model Canadian Model AEP Model UK Model
Ver 1.0 2003. 04
HCD-EP313 is the Amplifier, CD player, Tape Deck and Tuner section in CMT-EP313.
Model Name Using Similar Mechanism CD Section
TAPE Section
NEW
CD Mechanism Type
KSM-213EDP
Base Unit Name
BU-K7BD44B
Optical Pick-up Name
KSS-213E/C2N
Model Name Using Similar Mechanism
NEW
Tape Transport Mechanism Type
ADR2080FR4
SPECIFICATIONS Amplifier section AUDIO POWER SPECIFICATIONS: (U.S.A. model only) POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 6-ohm loads, both channels driven, from 120 10,000 Hz; rated 10 watts per channel minimum RMS power, with no more than 10% total harmonic distortion from 250 milliwatts to rated output. North American model: Continuous RMS power output (reference): 10 + 10 W (6 ohms at 1 kHz, 10% THD) European model: DIN power output (rated): 7 + 7 W (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 10 + 10 W (6 ohms at 1 kHz, 10% THD) Music power output (reference): 20 + 20 W Other models: The following measured at AC 230 V or AC 120 V, 50/ 60 Hz DIN power output (rated): 7 + 7 W (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 10 + 10 W (6 ohms at 1 kHz, 10% THD)
Inputs MD IN (phono jacks): Sensitivity 500 mV, impedance 47 kilohms Outputs PHONES (stereo minijack): Accepts headphones with an impedance of 8 ohms or more SPEAKER: Accepts impedance of 6 to 16 ohms. CD player section System Laser
Frequency response Tape deck section Recording system Frequency response
Antenna Antenna terminals Intermediate frequency AM tuner section Tuning range Pan-American model:
European model: Compact disc and digital audio system Semiconductor laser (λ=780 nm) Emission duration: continuous 2 Hz – 20 kHz (±0.5 dB)
Other models:
Antenna 4-track 2-channel stereo 50 – 13,000 Hz (±3 dB), using Sony TYPE I cassettes
Tuner section FM stereo, FM/AM superheterodyne tuner FM tuner section Tuning range 87.5 – 108.0 MHz (50-kHz step)
Intermediate frequency
FM lead antenna 75 ohms balanced 10.7 MHz
530 – 1,710 kHz (with the tuning interval set at 10 kHz) 531 – 1,710 kHz (with the tuning interval set at 9 kHz) 531 – 1,602 kHz (with the tuning interval set at 9 kHz) 530 – 1,710 kHz (with the tuning interval set at 10 kHz) 531 – 1,602 kHz (with the tuning interval set at 9 kHz) AM loop antenna, external antenna terminal 450 kHz
— Continued on next page —
MICRO HI-FI COMPONENT SYSTEM 9-877-237-01
Sony Corporation
2003D167800-1 © 2003.04
Home Audio Company Published by Sony Engineering Corporation
HCD-EP313 TABLE OF CONTENTS General Power requirements North American model: European model: Australian model: Mexican model: Argentine model: Taiwan model: Other models: Power consumption North American model: European model:
Other models: Dimensions (w/h/d) Mass Supplied accessories
1. SERVICING NOTES ······················································· 3 120 V AC, 60 Hz 230 V AC, 50/60 Hz 230 V AC, 50/60 Hz 120 V AC, 60 Hz 220 – 230 V AC, 50/60 Hz 110 – 120 V AC, 60 Hz 230 V AC, 50/60 Hz 35 watts 32 watts 0.3 watts (in the standby mode) 32 watts Approx. 148 × 233 × 208 mm Approx. 2.9 kg Remote (1) R6 (size AA) batteries (2) AM loop antenna (1) FM lead antenna (1)
Design and specifications are subject to change without notice.
2. GENERAL ·········································································· 5 3. DISASSEMBLY 3-1. Rear Cabinet ··································································· 7 3-2. CD Cabinet Section ························································ 8 3-3. Front Panel Section ························································· 8 3-4. CONTROL Board, BACK LIGHT Board ······················ 9 3-5. Tape Mechanism Deck ···················································· 9 3-6. Cassette Door Assy ······················································· 10 3-7. MAIN Board, POWER Board ······································ 10 3-8. CD Mechanism Deck (KSM-213EDP) ························· 11 3-9. Optical Pick-up (KSS-213E/C2N) ································ 11
4. MECHANICAL ADJUSTMENTS ····························· 12 5. ELECTRICAL ADJUSTMENTS ······························· 13 6. DIAGRAMS ······································································ 16 6-1. Block Diagram ······························································ 17 6-2. Printed Wiring Board – CD Section – ························· 18 6-3. Schematic Diagram – CD Section – ···························· 19 6-4. Printed Wiring Board – MAIN Section (COMPONENT SIDE) – ······· 20 6-5. Printed Wiring Board – MAIN Section (CONDUCTOR SIDE) – ······· 21 6-6. Schematic Diagram – MAIN Section – ······················· 22 6-7. Printed Wiring Board – CONTROL Section (COMPONENT SIDE) – ······· 23 6-8. Printed Wiring Board – CONTROL Section (CONDUCTOR SIDE) – ······· 24 6-9. Schematic Diagram – CONTROL Section – ··············· 25 6-10. Printed Wiring Board – POWER Section – ··············· 26 6-11. Schematic Diagram – POWER Section – ·················· 27 6-12. IC Pin Function Description ······································· 30
7. EXPLODED VIEWS 7-1. Overall Section ····························································· 32 7-2. Front Panel Section ······················································· 33 7-3. CD Cabinet Section ······················································ 34 7-4. Optical Pick-up Block (KSM-213EDP) ······················· 35
8. ELECTRICAL PARTS LIST ······································· 36
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
2
HCD-EP313 SECTION 1 SERVICING NOTES Notes on chip component replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing • Keep the temperature of the soldering iron around 270 ˚C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A)
To Exposed Metal Parts on Set
0.15 µF
1.5 k Ω
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the exterior.
Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. LASER DIODE AND FOCUS SEARCH OPERATION CHECK Carry out the “S curve check” in “CD section adjustment” and check that the S curve waveforms is output three times.
AC voltmeter (0.75 V)
Earth Ground Fig. A. Using an AC voltmeter to check AC leakage.
3
HCD-EP313
Service Position of the CD Mechanism Deck
Service Position of the Tape Cassette Mechanism Deck
4
HCD-EP313 SECTION 2 GENERAL
This section is extracted from instruction manual.
List of button locations and reference pages How to use this page
Illustration number r
Use this page to find the location of buttons and other parts of the system that are mentioned in the text.
DISPLAY wd (9, 14) R Name of button/part
R Reference page
Main unit BUTTON DESCRIPTIONS
ALPHABETICAL ORDER A–M
P–Z
BASS/TREBLE 5 (12) Cassette compartment qa DISPLAY wd (9, 14) Display window 2 DSG 4 (12) MD 6 (15)
PHONES jack qk PLAY MODE qj (6, 7) PRESET +/– 8 (9) Remote sensor 1 TUNER BAND 7 (8, 9) TUNING +/– 0 (8, 9) VOLUME 9 (13)
?/1 (power) wa (5, 9, 13) m/M (fast forward/rewind) 0 (6) ./> (go back/go forward) 8 (5, 6, 7, 12, 13) x (stop) ql (6, 7, 11, 17) X (pause) w; (6) CD N (play) ws (6, 7, 11) Z PUSH OPEN/CLOSE (open/ close) 3 (6) TAPE
m/M (fast forward/rewind) qf (10) xZ (stop/eject) qd (10, 11) X (pause) qs (10, 11) N (play) qg (10) z (record) qh (11)
1
2
3
4 5 6 7 8 9
wd ws wa w; ql qk qj
q; qa
qh qg qf qd qs
5
HCD-EP313
Remote control ALPHABETICAL ORDER
BUTTON DESCRIPTIONS
A–M
P–Z
BASS +/– 0 (12) CLEAR 8 (8, 9) CLOCK/TIMER SELECT w; (13) CLOCK/TIMER SET wa (5, 13) DISPLAY 2 (9, 14) DSG qa (12) MD qk (15)
PLAY MODE/DIRECTION qd (6, 7) PRESET +/– 5 (9) REPEAT/FM MODE qf (7, 9) SLEEP ql (12) TREBLE +/– 9 (12) TUNER BAND qh (8, 9) TUNER MEMORY qs (8) TUNING +/– 6 (8, 9) VOL +/– 7 (13)
?/1 (power) 1 (5, 9, 13) m/M (fast forward/rewind) 6 (6) ./> (go back/go forward) 5 (5, 6, 7, 13) x (stop) 4 (6, 7, 11, 17) X (pause) 3 (6) CD N (play) qj (6, 7, 11) TAPE nN qg (10)
wa w; ql qk
1 2
qj
3 4
qh
5
qg
6
qf qd
7
qs 8 9 qa 0
Setting the clock 1 Press ?/1 to turn on the system. 2 Press CLOCK/TIMER SET. 3 Press ./> repeatedly to set the hour.
4 5 6
Press CLOCK/TIMER SET. Press ./> repeatedly to set the minute. Press CLOCK/TIMER SET.
The clock starts working. To adjust the clock
1 Press CLOCK/TIMER SET. 2 Press ./> to select the clock display, then press CLOCK/TIMER SET.
3 Do the same procedures as step 3 to 6 above.
6
HCD-EP313 SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below.
SET
REAR CABINET
CD CABINET SECTION CD MECHANISM DECK (KSM-213EDP)
OPTICAL PICK-UP (KSS-213E/C2N)
FRONT PANEL SECTION
CONTROL BOARD, BACK LIGHT BOARD
TAPE MECHANISM DECK (ADR2080FR4)
MAIN BOARD, POWER BOARD
CASSETTE DOOR ASSY
Note: Follow the disassembly procedure in the numerical order given.
3-1. Rear Cabinet 3 five screws (+BVTP 3 × 8) 6 rear cabinet
2 three screws (+BTP 3 × 8) 1 two screws (+BVTP 3 × 8)
5 four screws (+KTP 3 × 12)
4 four screws (+KTP 3 × 12)
7
HCD-EP313
3-2. CD Cabinet Section 7 CD cabinet section
6 connector 2p (CN101) 1 screw (+BVTP 3 × 8)
5
4 two claws
2 wire (flat type) 21p (CN101)
3 two claws
3-3. Front Panel Section 4 connector 30p (CN202) (board to board) 5 connector 7p (CN502) 3 screw (+BTP 3 × 8) 1 two screws (+BVTP 3 × 10)
8 front panel section
7 6 connector 8p (CN501)
2 two claws
8
HCD-EP313
3-4. CONTROL Board, BACK LIGHT Board 3 nine screws (+BVTP 3 × 8)
5 CONTROL board
4 wire (flat type) 21p (CN301)
8 BACK LIGHT board 1 volume knob
2 screw (+BVTP 3 × 10)
6 two claws 7 connector 2p (CN305)
3-5. Tape Mechanism Deck
3 two screws (+BVTP 3 × 10)
2 screw (+BVTP 3 × 10)
4 tape mechanism deck
1 Open the cassette door.
9
HCD-EP313
3-6. Cassette Door Assy
2 cassette door assy
1 two claws
3-7. MAIN Board, POWER Board
2 screw (+BVTP 3 × 8)
3 MAIN board
5 four screws (+BVTP 4 × 12) 6 shield plate trans
1 connector 6p (CN901)
4 PT PWB cover
8 POWER board
7 two cushions
10
HCD-EP313
3-8. CD Mechanism Deck (KSM-213EDP)
5 panel CD
4 three claws 3 two screws (+PWH 2.6 × 10)
6 two cushion rubbers
q; wire (flat type) 16p (CN102)
qs CD mechanism deck (KSM-213EDP) 2 two screws (+PWH 2.6 × 10)
7 two cushion rubbers
qa CD board
9 screw (+P 2 × 5)
8 four remove soldrings.
1 CD deck cover
3-9. Optical Pick-up (KSS-213E/C2N) 6 KSS-213E/C2N
2 gear (A)
1 claw
4 5 sled shaft 3
11
HCD-EP313 SECTION 4 MECHANICAL ADJUSTMENTS Precaution 1. Clean the following parts with a denatured alcohol-moistened swab: record/playback heads pinch rollers erase head rubber belts capstan idlers 2. Demagnetize the record/playback head with a head demagnetizer. 3. Do not use a magnetized screwdriver for the adjustments. 4. After the adjustments, apply suitable locking compound to the parts adjusted. 5. The adjustments should be performed with the rated power supply voltage unless otherwise noted. Torque Measurement Mode
Torque meter
FWD
CQ-102C
FWD back tension
CQ-102C
REV
CQ-102RC
REV back tension
CQ-102RC
FF/REW
CQ-201B
FWD tension
CQ-403A
REV tension
CQ-403R
12
Meter reading 2.94 – 7.84 mN • m (30 to 79 g • cm) (0.42 – 1.11 oz • inch) 0.15 – 0.59 mN • m (2 to 6 g • cm) (0.03 – 0.08 oz • inch) 0.15 – 0.59 mN • m (2 to 6 g • cm) (0.03 – 0.08 oz • inch) 0.15 – 0.59 mN • m (2 to 6 g • cm) (0.03 – 0.08 oz • inch) 6.86 – 17.64 mN • m (70 to 179 g • cm) (0.98 – 2.49 oz • inch) 9.8 mN • m or more (100 g • cm or more) (1.4 oz • inch or more) 9.8 mN • m or more (100 g • cm or more) (1.4 oz • inch or more)
HCD-EP313 SECTION 5 ELECTRICAL ADJUSTMENTS DECK SECTION 1. 2. 3. 4. 5.
6. 7.
3.
0 dB=0.775V
test tape P-4-A100 (10kHz, –10dB)
Demagnetize the record/playback head with a head demagnetizer. Do not use a magnetized screwdriver for the adjustments. After the adjustments, apply suitable locking compound to the parts adjusted. The adjustments should be performed with the rated power supply voltage unless otherwise noted. The adjustments should be performed in the order given in this service manual. (As a general rule, playback circuit adjustment should be completed before performing recording circuit adjustment.) The adjustments should be performed for both L-CH and RCH. Switches and controls should be set as follows unless otherwise specified. Tape
Signal
Used for
P-4-A100
10 kHz, –10 dB
Azimuth Adjustment
WS-48B
3 kHz, 0 dB
Tape Speed Adjustment
test tape P-4-A100 (10kHz, –10dB)
MAIN board J203 speaker terminal
oscilloscope
L R
Waveform of oscilloscope
in phase
45°
90°
good
135°
180° wrong
After the adjustments, apply suitable locking compound to the parts adjusted.
Adjustment Location: Record/Playback/Erase Head
level meter
set
MAIN board J203 speaker terminal
set
4. [Record/Playback Head Azimuth Adjustment] Procedure: 1. Mode : Playback
Mode: Playback
+
[Tape Speed Check] Procedure: 1. Turn the power on. 2. Insert the WS-48B into deck. 3. Press the N button of deck. 4. Check the reading of frequency counter becomes 3000 ± 90 Hz.
–
2.
Turn the adjustment screw and check output peaks. If the peaks do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1 dB of peak.
L-CH peak
screw position
output level
within 1 dB
Sample Value of Wow and flutter W.RMS (JIS) less than 0.3% (test tape: WS-48B) Adjustment Location: Record/Playback Head.
within 1dB
R-CH peak
L-CH peak
R-CH peak
screw position
adjustment screw
Note: Refer to “3-6. Cassette Door Assy” (see page 10)
13
HCD-EP313
RFDC signal waveform
CD SECTION
VOLT/DIV: 200 mV TIME/DIV: 500 ns
Note: 1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given. 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. 3. Use an oscilloscope with more than 10MΩ impedance. 4. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks.
S-curve Check Connection:
level: 0.7 ± 0.2 Vp-p
Checking Location: CD board (Conductor side) oscilloscope
RFAC Level Check Connection:
CD board TP (FE) TP (DVC)
+ –
oscilloscope CD board
Procedure: 1. Connect an oscilloscope to test point TP (FE) and TP (DVC) on the CD board. 2. Turn the power on. 3. Put the disc (YEDS-18) in and turned power switch on again and actuate the focus search. (actuate the focus search when disc table is moving in and out) 4. Check the oscilloscope waveform (S-curve) is symmetrical between A and B. And confirm peak to peak level within 2 ± 1 Vp-p. S-curve waveform
symmetry
TP (RFAC) TP (VC)
+ –
Procedure: 1. Connect an oscilloscope to test point TP (RFAC) and TP (VC) on the CD board. 2. Turn the power on. 3. Put the disc (YEDS-18) in to playback the number five track. 4. Confirm that oscilloscope waveform is clear and check RFAC signal level is correct or not. Note: A clear RFAC signal waveform means that the shape “◊” can be clearly distinguished at the center of the waveform.
RFAC signal waveform
A
within 2 ± 1 Vp-p
VOLT/DIV: 200 mV TIME/DIV: 500 ns
B level: 0.9 ± 0.4 Vp-p Note: • Try to measure several times to make sure than the ratio of A : B or B : A is more than 10 : 7. • Take sweep time as long as possible and light up the brightness to obtain best waveform.
Checking Location: CD board (Conductor side) RFDC Level Check Connection: oscilloscope CD board TP (RFDC) TP (DVC)
+ –
Procedure: 1. Connect an oscilloscope to test point TP (RFDC) and TP (DVC) on the CD board. 2. Turn the power on. 3. Put the disc (YEDS-18) in to playback the number five track. 4. Confirm that oscilloscope waveform is clear and check RFDC signal level is correct or not. Note: A clear RFDC signal waveform means that the shape “◊” can be clearly distinguished at the center of the waveform.
14
Checking Location: CD board (Conductor side)
HCD-EP313
E-F Balance Check Connection:
Checking Location: – CD BOARD (Conductor Side) –
oscilloscope CD board TP (TE) TP (DVC)
+ –
Procedure: 1. Connect an oscilloscpe to test point TP (TE) and TP (DVC) on the CD board. 2. AC is put in pushing CD N button. 3. FL tube carries out all lights and goes into CD test mode. 4. Put the disc (YEDS-18) in to playback the number five track. 5. Press the CD N button. (The tracking servo and the sledding servo are turned OFF) 6. Check the level B of the oscilliscope's waveform and the A (DC voltage) of the center of the Traverse waveform. Confirm the following : A/B x 100 = less than ± 22% Traverse Waveform
TP (VC) IC103 TP (DVC)
TP (RFAC) TP (FE)
IC101
TP (TE) TP (RFDC)
Center of the waveform B A (DC voltage)
0V
level: 1.15 ± 0.5 Vp-p
7.
Press the CD N button. (The tracking servo and sledding servo are turned ON) Confirm the C (DC voltage) is almost equal to the A (DC voltage) is step 4. To exit from this mode, turn the power off.
8.
Notes: • Always move the optical pick-up to most inside track when exiting from this mode. Otherwise, a disc will not be unloaded. • Do not run the sled motor excessively, otherwise the gear can be chipped.
Traverse Waveform
C (DC voltage)
0V Tracking servo Sled servo OFF
Tracking servo Sled servo ON
Checking Location: CD board (Conductor side)
15
15
HCD-EP313 SECTION 6 DIAGRAMS • Circuit Boards Location MAIN board
CD board
• Waveforms – CD Board –
– CONTROL Board –
– MAIN Board –
1 IC103 qg (RFAC)
5 IC301 0 8.6MHz OUT
7 Q453,Q454 collector
(CD Play Mode)
1.1Vp-p 200mV/DIV, 1 µs/DIV
20 ms
10Vp-p
5V/DIV, 10 ms/DIV
6 IC301 7 32kHz OUT
2 IC101 el (FE) (CD Play Mode)
BACK LIGHT board
200mVp-p 50mV/DIV, 200 µs/DIV
3 IC101 ra (TE) (CD Play Mode)
250mVp-p
TRANSFORMER board
100mV/DIV, 200 µs/DIV
CONTROL board
4 IC101 yj (XTAO)
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.)
59ns 1V/DIV, 20ns/DIV
For schematic diagrams.
For printed wiring boards.
Note: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. f • : internal component. • 2 : nonflammable resistor. • 1 : fusible resistor. • C : panel designation.
Note: • X • Y f • •
Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
• A : B+ Line. • B : B– Line. • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. • Circled numbers refer to waveforms. • Abbreviation CND : Canadian model • Signal path. F : TUNER (FM) J : CD d : MD E : PB (TAPE) a : REC (TAPE)
: parts extracted from the component side. : parts extracted from the conductor side. : internal component. : Pattern from the side which enables seeing.
• Indication of transistor C Q
These are omitted.
B E
B C
E These are omitted.
16
16
5.4Vp-p
30 µs
2.4Vp-p
1V/DIV, 10 µs/DIV
(Rec mode)
10 µs 5V/DIV, 5 µs/DIV
10Vp-p
HCD-EP313 6-1. Block Diagram
PB/REC EQ AMP IC601
J201 L MD R-CH
R
19 AUX L
OUT L 18
23 TU L
OUT R 16
2 TAPE L 21 CD L
µ CON IC301
R-CH
MUTE Q401
CONT 13 REC OUT 28
J202 PHONES
4 L IN L OUT + 8
REG Q701
+VM
MUTE 14
P CONT Q702
71 TU ON
L
MUTE CONT Q403
L OUT - 9
MUTE
LCD301 R-CH
79 DATA
CLK
78 PLL CLK
CE
27 PLL CE
TUNED
76 TUNED
STEREO
SEG0 38 . SEG20 41 46 COM0 61 COM2 63
74 STEREO
MUTE
D211
24
75 IFC
D IN
R
R CH
6
LIQUID CRYSTAL DISPLAY
D OUT
J203 SPEAKER
5 STBY
AMP STBY 48
L-CH R-CH
1
POWER AMP IC204
Q601
DSG 22
TUNER UNIT +10V
R CH
IC800 3
49 TU MUTE
DECK BLOCK
• RCH is omitted due to same as L-CH. • Signal Path S302,304,306 S308,310-312
: FM
FUCTION KEY
: CD
S301,303,305,307 S309,313,314
: MD
KEY1 17 Q504-511 REC/PB SWITCH
R-CH REC/PB HEAD
KEY2 16 L451 BIAS
R-CH
X301 32.768kHz BIAS OSC Q453 Q454
X302 8.64MHz
S315
: REC (TAPE)
VOL ENCODER
VOL ENC 13
19 X IN Q306 10 X OUT
Q450,451
: PB (TAPE)
6 XT1 7 XT2
ERASE HEAD
FUCTION KEY
STBY LED 56
LED301 ECO LED
LED DRIVE
+VM
MECHA BLOCK REC
50 DECK1
PLAY
58 DECK3
DECK POWER DECK MOTOR
LED302-307 (BACK RIGHT)
53 BIAS BK LED 55
LED DRIVE
51 DECK2
Q501,502 MOTOR DRIVE
M
Q301
µCON +B
52 MOTOR
IC303
OPTICAL PICK-UP BLOCK (KSM-213EDP)
Q302 RF AMP IC103
VC A
27 VC +5V 6 A
B
RFAC 15
51 RFAC
L OUT 72
RFDCO 28
43 RFDC
R OUT 75
RESET 5
RESET SWITCH
Q303,304
IC302 D301 1
RESET
8 C
D E F
9 D
FE 16
39 FE
10 E
TE 18
41 TE
11 F Q101 LD DRIVE
40 SE FEI 17
1 LD
V ECO
POWER DOWN 59 R-CH
PD
DATA 5
80 CD DATA
CLOK 7
1 CD CLK
XLAT 6
70 LATCH
SQCK 2
72 C SQCK
SCOR 20
SW 12
20 SCOR
SQSO 1
2 SQSO
SENS 8
73 SENS
HOLD 12
Q205
Q206
HOLD
AC DET
D213 D212
2 PD
VR
D206
S101 LIMIT IN SW
SSTP 27
F+
13 CH1RO
F-
CH1RI 3
32 FFDR
14 CH1FO
CH1FI 2
33 FRDR
11 CH2RO
CH2RI 6
30 TFDR
D205
POWER AMP VCC
MOTOR/COIL DRIVE IC102 XTAI 66
IC200
X101 16.9344MHz
+VM REG
+VM
XTAO 67
PT901 POWER TRANS
D201-204
Q402
TTRACKING COIL
VM
SCLK 9
RFDCI 29
GND
FOCUS COIL
D306
+5V REG
2
7 B
C
LD
DIGITAL SERVO IC101
D305
REMOTE 1 CONTROL 3 RECEIVER
RMC 23
CD +7V Q102,D101
T+
M101 SLED MOTOR
12 CH2FO
CH2FI 5
31 TRDR
18 CH3RO
CH3RI 23
29 SRDR
17 CH3FO
CH3FI 24
28 SFDR
16 CH4RO
CH4INS 25
26 MDP
15 CH4FO
MUTE 20
+3.3V
+3.3V REG
Q406 CD +5.5V
+5.5V
IC601 VSS
Q404,405
M
M102 SPINDLE M MOTOR
+5.5V REG
+7V REG
CD ON 71 XRST 3
POWER CONTROL Q200
69 XRST POWER 21
RY901
RELAY DRIVE D901-904
3 PWM1
CD OPEN/CLOSE
L901
65 PWM2
V ECO
68 PWM3
OPEN
4 LDON
CLOSE
18 T SW
17
PT902 SUB TRANS
17
LINE FILTER
AC IN
HCD-EP313 6-2. Printed Wiring Board – CD Section –
• See page 16 for Circuit Boards Location.
• Semiconductor
Location
A
Ref. No.
KSS-213E/C2N
M102
B
Location
D101
F-5
IC101 IC102 IC103
E-4 C-5 D-2
Q101 Q102
C-2 G-5
TP (VC)
C
IC102 M101
D
IC103 TP (RFAC)
TP(RF)
TP (DVC)
E
B IC101 CONTROL
CN301 (Page 23)
F
G 1-680-849-
1
2
3
4 18
5 18
6
7
8
HCD-EP313 • See page 16 for Waveforms.
6-3. Schematic Diagram – CD Section –
• See page 28 for IC Block Diagrams.
TP(VC)
TP (RF)
C150 0.1
KSS-213E/C2N
0uH
M101
M102
0uH
C199 470p CONTROL
CN301 (Page 25)
B
19
19
HCD-EP313 6-4. Printed Wiring Board – MAIN Section (COMPONENT SIDE) –
• See page 16 for Circuit Boards Location.
ANTENNA (TO TUNER UNIT)
A
• Semiconductor
Location
MAIN BOARD
TO (CD DOOR)
Ref. No.
(COMPONENT SIDE)
B J201
A
L
TO CONTROL BOARD CN302 (Page 23)
MD R
C
TO DECK BLOCK (HEAD)
D 2 3
6 7 8
9 10 11
J202
E
TO DECK BLOCK (MOTOR)
SPEAKER
F
IMPEDANCE USE 6-16Ω L
IC800
IC200
G
R
C TO TRANSFORMER BOARD CN901 (Page 26)
IC204
H 1-688-567
1
2
3
4
5
6 20
20
7
8
9
D200 D201 D202 D203 D204 D205 D206 D207 D209 D210 D211 D212 D213 D403 D404 D405 D501 D602 D603 D801 D802 D803 D804
H-4 H-6 G-7 H-6 G-7 G-6 G-7 F-6 C-2 C-2 E-6 H-6 H-6 F-6 F-6 F-5 C-7 C-5 C-5 F-4 D-9 F-3 D-8
IC200 IC204 IC800
G-6 H-4 F-4
Q205 Q206 Q402 Q404 Q405 Q406 Q451 Q453 Q454 Q502
C-4 B-4 F-6 F-6 F-6 F-5 D-6 D-7 D-7 F-6
1 4 5
PHONES
J203
Location
10
HCD-EP313 6-5. Printed Wiring Board – MAIN Section (CONDUCTOR SIDE) –
• See page 16 for Circuit Boards Location.
A
• Semiconductor
Location
MAIN BOARD
Ref. No.
(CONDUCTOR SIDE)
B
C
14
1
IC601 15
28
IC601
C-5
Q200 Q400 Q401 Q403 Q450 Q501 Q504 Q505 Q506 Q507 Q508 Q509 Q510 Q702 Q801 Q802 Q804
F-7 E-4 E-4 E-3 D-7 E-7 C-7 D-7 C-7 C-7 D-7 C-6 C-7 B-6 D-8 D-8 D-8
D
E
F
G
H 1-688-567
1
2
3
4
5
6 21
21
7
8
9
Location
10
HCD-EP313 • See page 16 for Waveform. • See page 29 for IC Block Diagram.
6-6. Schematic Diagram – MAIN Section –
(TO TUNER UNIT)
MAIN BOARD
ANTENNA L J201
(CD DOOR)
MD R
Q601,602 DSG SWITCH CN101 0
0
-3.3
0.6
TO CONTROL BOARD CN302 (Page 25)
PHONES
IC800 NJM4565D
MUTE 0
A
J202
IC800 HEAD PHONE AMP
13.8
6.8
9
0
9
0
MUTE
0
0
0
0
– + – +
13.2 9
0
v+
v–
MUTE
-3.3
0
0
-6.8
0 -3.5
MUTE
2.5 Q205,206 AC DETECT
0.2
0.2 Q701,702 TUNER POWER ON/OFF SWITCH
-0.2
0.5
IC204 POWER AMP
L
J203 SPEAKER
0
0
0
0
0
0
0
0
0
0
0
0
8.2
8.0
8.1
8.3
0
0
3.7
0
-3.5
0
18.1
0
R
17.2
0
IMPEDANCE USE 6-16 Ω
IC601 PB/REC EQ AMP
-3.5 0
0
0
0
0
0
0
0
0
0
0.4 5.2 0.2
-5.3 0.3
– REC/PLAY SWITCH – -3.5
0.1
3.0(-6.9) Q400,401,403 MUTE 0(-23.1)
4.5(0)
3.0 (-6.9)
3.3(0)
TA7805S
0 (4.9)
IC200
3.3 (-12.2) 3.0 (-6.9) 2.5(-0.6) 0
SWITCH
0 2.5(-0.6) REG
R-CH
7
0.3(1.7)
4.9
7.5
7.5
17.9
5.5
9(8.4) 8.6(2.4)
(ERASE) 9(2.5)
17.1 REG
0.9(1.3)
8.6(2.9)
0.3(0.7) 0.3 (0.7)
9(8.4)
9(2.5)
1.0
0 2SA1036K 0(5.0)
SWITCH 9.0(0)
0.5
7 – BIAS OSC –
16.4
– BIAS –
0.7
0.1(8.9)
0
9 0.1
0.8
0(-23) 0
L-CH (REC/PB)
0
+VM REG.
3.3(-0.6)
DECK BLOCK
9(8.1)
9 SWITCH
22
22
Q404, 405 POWER CONTROL 0.1
C
RELAY DRIVE
17.9
0
TO TRANSFORMER BOARD CN901 (Page 27)
HCD-EP313 6-7. Printed Wiring Board – CONTROL Section (COMPONENT SIDE) –
• See page 16 for Circuit Boards Location.
• Semiconductor
Location Ref. No.
A
CONTROL BOARD
(COMPONENT SIDE) (STANDBY)
BACK LIGHT BOARD
DSG
LIQUID CRYSTAL DISPLAY
B BASS/TRE DISPLAY
IC303
C MD
CD
TUNER
A
B
TO MAIN BOARD CN202 (Page 20)
TO CD BOARD CN101 (Page 18)
D ?/1
1-688-568
VOLUME
>
. x
X
E PLAY MODE
m
M
1-688-569
1
2
3
4
5
23
23
6
7
8
Location
D301 D302 D303 D304 D305 D306 D307 D308
D-5 E-6 D-6 E-5 E-6 D-7 D-5 E-5
IC303
B-6
Q303
D-6
HCD-EP313 6-8. Printed Wiring Board – CONTROL Section (CONDUCTOR SIDE) –
• See page 16 for Circuit Boards Location.
• Semiconductor
Location Ref. No.
A
CONTROL BOARD
(CONDUCTOR SIDE)
41
40
B 60
IC301
61
21 20
80
1
C
D IC302
E 1-688-569
1
2
3
4
5
24
24
6
7
8
Location
IC301 IC302
B-4 D-5
Q301 Q302 Q304 Q305 Q306
B-3 D-4 D-6 D-6 A-7
HCD-EP313 6-9. Schematic Diagram – CONTROL Section –
• See page 16 for Waveforms.
CONTROL BOARD
BACK LIGHT BOARD BACK LIGHT 270 270
IC303
LIQUID CRYSTAL DISPLAY
0.1
LED SWITCH 0 5.2
5.2
5.4
REMOTE SENSOR
LED SWITCH
(STANDBY)
0.6
2.6
2.6
2.6
2.6
2.6
5.1
0
5.1
0
0
0
0
0
0
5.6
5.3
0
m
A
DISPLAY
2.6
M
I/1
2.6
5.2
2.6
2.6 2.6
TO MAIN BOARD CN202 (Page 22)
2.6
2.3
2.6 5.2
X
x
.
>
VOLUME
2.6
2.4
IC301
2.6
5.2
SYSTEM CONTROLLER
2.6
5.2
2.6
5.1
2.6
5.2
2.6
0
2.6
0.5
2.6
0.8
2.6
0.5
2.6
0
2.6
0
5.2
0.1
0
5.2
4.8
0.1
0
0
5.3
5.3
3.4
0.1
5.3
2.4
5.2
2.6
0
2.6
2.5
2.8
2.2 18P
2.2
0
5.2
0.3
10UH
18P
B 5.7
39K / J RESET SWITCH
8.3 7.6
68P
5.4
0
7.4
5.2
5.6
5.6
TO CD BOARD CN101 (Page 19)
68K / J
5.4 0
5V REG.
IC302 RESET
25
25
HCD-EP313 6-10. Printed Wiring Board – POWER Section –
• See page 16 for Circuit Boards Location.
• Semiconductor
Location
A
TRANSFORMER BOARD
B AC IN
C
C
TO MAIN BOARD CNA201 (Page 20)
SUB POWER TRANSFORMER
D
POWER TRANSFORMER
5
9
4
1
7
* : NOT REPLACEABLE
1
BUILT IN TRANSFORMER
*
E
F 8
17 1-688-570
1
2
3
4
26
26
5
6
Ref. No.
Location
D901 D902 D903 D904
C-3 C-3 C-3 C-3
HCD-EP313 6-11. Schematic Diagram – POWER Section –
TRANSFORMER BOARD
C
* : BNUOITLTR EI NP LTARCAENAFBOLREM E R
*
TO MAIN BOARD CNA201 (Page 22)
SUB POWER TRANFORMER
27
27
HCD-EP313
• IC Block Diagrams – CD Board –
VDD VSS AVDD3
PCO FILI FILO CLTV
AVSS3
RFAC BIAS ASYI ASYO
AVDD0
IGEN
AVSS0
ADIO
RFDC CE TE
60
59 58 57
56 55 54 53
52
51 50 49 48
47
46 45
44
43 42 41
ERROR CORRECTOR
INTERNAL BUS
DIGITAL OUT
LRCK 61 PCMD 62
IC103 CXA2581N-T4
DOUT
IC101 CXD3017Q
D/A INTERFACE
DIGITAL PLL
16K RAM
RW/ROM
A
40 SE 39 FE 38 VC
ASYMMETRY CORRECTOR
– +
B
– +
D
EFM DEMODULATOR
28 RFDCO
C DVC
DVC VCC
OPERATIONAL AMPLIFIER ANALOG SWITCH
VC
A/D CONVERTER
BCK 63
– +
DVC VC
EMPH 64 XVDD 65
RW/ROM
VOFST
27 VC
VC
66 67 68 69 70 71
LD
TIMING LOGIC
CLOCK GENERATOR SERVO DSP
LOUT1 72 PWM
AVSS1 73 AVSS2 74 LOUT2 75
SUBCODE PROCESSOR
PWM
AOUT2 77 AVDD2 78 RMUT 79 LMUT 80
PWM GENERATOR
FOCUS SERVO
FOCUS PWM GENERATOR
TRACKING SERVO
TRACKING PWM GENERATOR
SLED SERVO
SLED PWM GENERATOR
SERVO INTERFACE
OVER SAMPLING DIGITAL FILTER
AIN2 76
37 XTSL 36 TES1 35 TEST 34 VSS 33 32 31 30 29 28
SERVO AUTO SEQUENCER
SERIAL IN INTERFACE
2
EQ IN
3
AC SUM
GND
RFAC SUMMING AMP
4
5
A B C D
B
C D
5 6 7 8
9 10 11 12 13 14 15 16 17 18 19 20
SQSO SQCK
XRST
SYSM
DATA XLAT CLOK SENS
SCLK VDD ATSK
VCC
22 VCC
VOFST – +
21 CEI – +
20 CE
D
VC RW/ROM
GM
19 TE BAL
– +
F 11
GM
SW 12
APC-OFF (Hi-Z) RW/ROM (H/L)
18 TE
RW/ROM RW/ROM
DVCC 13
PRFVCC
CH4BIN
CH4SIN'
CH4SIN
CH3FIN
CH3RIN
CAPAIN3
GND
MUTE
POWVCC
CH3OUTR
CH3OUTF
CH4OUTR
CH4OUTF
B
28
27
26
25
24
23
22
21
20
19
18
17
16
15
DVC DVC 14
D A
17 FEI
VOFST – +
– +
C DVC VC
F
R
R
RW/ROM
MUTE
RFAC 15
INTERFACE F LEVEL SHIFT
THERMAL SHUTDOWN
F INTERFACE R
23 RFG
VC
IC102 BA5974FP-E2
F
RFAC VCA
RW/ROM
C2PO SCOR
4
WFCK XUGF XPCK GFS
3
26 RFC 25 VFC 24 BST
DVC
A B C D
6 7 8 9
21 COUT
1 2
B C A
E 10 CPU INTERFACE
EQ APC AMP
A
24 FOK 23 DFCT 22 MIRR
MIRR, DFCT, FOK DETECTOR
PD
RW/ROM
26 MDP 25 LOCK
DIGITAL CLV
1
EQ ON/OFF
FRDR FFDR TRDR TFDR SRDR SFDR
27 SSTP
3rd ORDER NOISE SHAPER
SPOA SPOB XLON
XTAI XTAO XVSS AVDD1 AOUT1 AIN1
30 DC OFST 29 RFDCI
F
R INTERFACE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
CH1RIN
CAPAIN1
CH2FIN
CH2RIN
CAPAIN2
GND
VREFIN
POWVCC
CH2OUTR
CH2OUTF
CH1OUTR
CH1OUTF
R
CH1FIN
R
VREFOUT
F
28
28
16 FE
4 5
6 7
8
9 10 11 12
IN2 STBY
MUTE VCC
+OUT2
–OUT2 PWR GND –OUT1
OUTPUT AMP
INPUT AMP + –
+OUT1
1 2 3
DC IN1 PRE GND
VSS
TON_H-R
TON_H-L
TAPE-R
TAPE-L
TON_L-R
OUT-R
TON_L-L
OUT-L
AUX-L
AUX-R
CD-L
CD-R
TUNER-L
TUNER-R
REC-O_R
REC-O_L
HCD-EP313
– MAIN Board – IC601 BD3881FV
IC204 LA4636
OUTPUT AMP
+ –
INPUT AMP
29
HCD-EP313
6-12. IC Pin Function Description • IC301
LC877140A (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
O-CLOCK
O
Clock output to the CD unit
2
I-SQSO
I
SUB-Q data input from the CD unit
3
O-PWM1
O
PWM1 signal output to the CD unit
4
O-LDON
O
LD ON signal output to the CD unit
5
I-RESET
I
Reset signal input from the reset IC (IC302)
6
32KHz IN
I
Resonator terminal (32.768kHz)
7
32KHz OUT
O
Resonator terminal (32.768kHz)
8
VSS1
—
Ground terminal
9
8.64MHz IN
I
Resonator terminal (8.64MHz)
10
8.64MHz OUT
O
Resonator terminal (8.64MHz)
11
VDD1 +5V
—
Power supply terminal
12
I-HOLD
I
Voltage detection signal input
13
I-VOL
I
Volume signal input from the encoder
14
O-MUTE
O
Muting signal output
15
I-SUFFIX
I
Model setting input terminal
16
I-KEY2
I
Key input 2
17
I-KEY1
I
Key input 1
18
I-CDTSW
I
CD door open/close switch signal input
19
O-CLKSHIFT
O
Clock shift control signal output
20
I-SCOR
I
SCOR signal input from the CD unit
21
O-POWER
O
Power relay control signal output
22
O-DSG
O
DSG signal output
23
I-RMC
I
Remote sensor signal input from the IC303
24 to 38
SEGMENT 0 to 14
O
Segment signal output to the liquid crystal display module
39
VDD2 +5V
—
Power supply terminal
40
GND
—
Ground terminal
41 to 46 SEGMENT 15 to 20
O
Segment signal output to the liquid crystal display module
47
NC
—
Not used (open)
48
AMP STBY
O
Standby control signal output to the power amplifier
49
O-TUMUTE
O
Muting signal output to the tuner
50
I-DECK1
I
Tape switch status signal input from the tape deck
51
I-DECK2
I
Tape switch status signal input from the tape deck
52
O-MOTOR
O
Motor control signal output to the tape deck
53
O-BIAS
O
Bias control signal output to the bias oscillation circuit
54
TU-ON
O
Tuner power supply control signal output
55
O-BKLED
O
Back light control signal output
56
O-STBYLED
O
STANDBY LED control signal output
57
O-KSCAN
O
Not used (open)
58
I-DECK3
I
Tape switch status signal input from the tape deck
59
I-POWERDOWN
I
Power down detection signal input
60
NC
—
Not used (open)
61
COM0/PL0
O
Common signal output to the liquid crystal display module
62
COM1/PL1
O
Common signal output to the liquid crystal display module
63
COM2/PL2
O
Common signal output to the liquid crystal display module
64
NC
—
Not used (open)
65
PWM2
O
PWM2 signal output to the CD unit
66
VSS3
—
Ground terminal
67
VDD3 +5V
—
Power supply terminal
68
O-PWM3
O
PWM3 signal output to the CD unit
69
O-XRST
O
Reset signal output to the CD unit
30
HCD-EP313
Pin No.
Pin Name
I/O
Description
70
O-XLAT
O
Latch signal output to the CD unit
71
O-CDON
O
CD power supply control signal output
72
O-SQCK
O
SUBQ clock output to the CD unit
73
I-SENS
I
SENS signal input from the CD unit
74
I-STEREO
I
Stereo/mono detection signal input from the tuner
75
I-IFC
I
Data input from the tuner
76
I-TUNE
I
Tuner tuned status signal input
77
O-PLLCE
O
Tuner chip enable signal output to the tuner
78
O-PLLCLK
O
Clock signal output to the tuner
79
O-MADATA
O
Data output to the tuner
80
O-DATA
O
Data output to the CD unit
31
HCD-EP313 SECTION 7 EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may have some differences from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.
•
The mechanical parts with no reference number in the exploded views are not supplied. Abbreviation CND : Canadian model
•
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
7-1. Overall Section
CD cabinet section
#2
5 #2
#1
#5
4
#1 #2 #1
3 #2
2
#2 not supplied
#2 Front panel section
#3
6
#1
7
#2
#5
#4
1
9 8 9 10 not supplied
11
T901
11 Ref. No. 1 2 2 3 4 5 6 7 08 08
32
Part No.
Description
MOUNTING LUG A-4732-945-A MAIN BOARD, COMPLETE (AEP,UK) A-4732-950-A MAIN BOARD, COMPLETE (US,CND) TUNER UNIT COVER, CD DECK 4-245-240-01 CABINET,REAR SHIELD PLATE TRANS COVER, PT PWB 1-555-795-00 CORD, POWER (AEP,UK) 1-783-532-11 CORD, POWER (US,CND)
Remark
Ref. No.
Part No.
9 10 11 0 T901 0 T901
CUSHION-R 1-688-570-11 TRANSFORMER BOARD RUBBER FOOT 1-439-656-11 TRANSFORMER, POWER (US,CND) 1-439-657-11 TRANSFORMER, POWER (AEP,UK)
#1 #2 #3 #4 #5
7-685-248-14 7-685-646-14 7-685-661-79 7-685-647-14 7-685-546-14
Description
SCREW +KTP 3X12 TYPE2 NON-SLIT SCREW +BVTP 3X8 TYPE2 N-S SCREW +BVTP 4X12 TYPE2 SLIT SCREW +BVTP 3X10 TYPE2 N-S SCREW +BTP 3X8 TYPE2 N-S
Remark
HCD-EP313
7-2. Front Panel Section #2
61
62 69
60
70 63
58
71
65 64
59
66 #5
57 #4
68 #4
53 67
54 51
#4
55 56
52
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
51 52 53 54 55
A-4737-466-A DOOR CASSETTE ASSY SPRING, CASSETTE 4-245-244-01 HOLDER,CASSETTE 4-238-631-01 TAPE SPRING 4-245-239-01 CABINET,FRONT
63 64 65 66 67
4-245-248-01 BUTTON,CD 4-245-250-01 BUTTON,BASS 4-245-251-01 BUTTON,ENTER KEY CASS, PLATE 4-245-252-01 BUTTON, CASSETTE
56 57 58 58 59
4-244-787-01 4-245-253-01 4-245-245-01 4-245-245-11 4-242-318-01
68 69 69 70 71
1-796-689-11 A-4732-942-A A-4732-948-A 1-688-568-11
60 61 62
4-245-249-01 BUTTON,DISPLAY 4-245-247-01 BUTTON,FUNCTION COVER, KEY SHEET
#2 #4 #5
7-685-646-14 SCREW +BVTP 7-685-647-14 SCREW +BVTP 7-685-546-14 SCREW +BTP
KNOB (VOLUME) PLATE,FUNCTION WINDOW,DISPLAY (AEP,UK) WINDOW,DISPLAY (US,CND) OIL-DMPR, 70
DECK MECHANICAL CONTROL BOARD, COMPLETE (AEP,UK) CONTROL BOARD, COMPLETE (US,CND) BACK LIGHT BOARD WIRE (FLAT TYPE) 3X8 TYPE2 N-S 3X10 TYPE2 N-S 3X8 TYPE2 N-S
33
HCD-EP313
7-3. CD Cabinet Section
101
111 112 113
102
114
S800
104 116 not supplied
105
107 106 115 108
107
115 115
KSM-213EDP
108
#6
110 115
Ref. No.
Part No.
Description
101 102 104 105 106
A-4737-468-A DOOR CD ASSY SPRING, CD 4-242-171-01 DAMPER 150 N 4-247-493-01 PANEL, CD 1-757-055-11 WIRE, PARALLEL (FFC) (16 CORE)
111 112 113 114 115
4-246-193-01 4-246-191-01 4-249-238-01 4-246-192-01 3-921-725-11
HOLDER, CHUCK A PLATE, MAGNET MAGNET BASE, CHUCK N SCREW (2.6X10), +PWH
107 108 110
CUSHION RUBBER CUSHION RUBBER A-4728-536-A CD BOARD, COMPLETE
116 S800 #6
RING PLATE 1-692-960-11 SW, PUSH 1-1-1 7-621-255-32 SCREW +P 2X5
34
Part No.
Description
Remarks
Ref. No.
Remarks
HCD-EP313
7-4. Optical Pick-up Block (KSM-213EDP)
605
604
608
601 606 607
M102
Ref. No.
Part No.
Description
601 0 604 605 606
2-626-908-01 8-820-053-03 2-626-907-11 X-2162-709-1
SHAFT, SLED OPTICAL PICK-UP KSS-213E/C2N GEAR (A) CHASSIS ASSY (CDP), MOTOR
Remarks
Ref. No. 607 608 M102
Part No.
Description
Remarks
2-627-003-01 GEAR GEAR (B) (RP) 3-713-786-51 SCREW +P 2X3 X-2625-769-1 GEAR ASSY (MB) (RP), MOTOR (SLED)
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
35
HCD-EP313 BACK LIGHT
SECTION 8 ELECTRICAL PARTS LIST
CD
NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX, -X mean standardized parts, so they may have some difference from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • CAPACITORS: uF: µF Ref. No.
Part No.
•
• •
RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable COILS uH: µH SEMICONDUCTORS In each case, u: µ, for example: uA...: µA... , uPA... , µPA... , uPB... , µPB... , uPC... , µPC... , uPD..., µPD...
Description
Remarks
1-688-568-11 BACK LIGHT BOARD **************** 4-245-258-01 HOLDER,LED
Ref. No.
•
Abbreviation CND : Canadian model When indicating parts by reference number, please include the board name. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
Part No.
Description
C162 C163 C165 C167 C168
1-126-382-11 1-126-933-11 1-164-360-11 1-162-920-11 1-162-919-11
ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
100uF 100uF 0.1uF 27PF 22PF
20.00% 16V 20.00% 16V 16V 5% 50V 5% 50V
Remarks
C171 C172 C181 C182 C183
1-115-412-11 1-162-927-11 1-115-412-11 1-162-927-11 1-162-968-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
680PF 100PF 680PF 100PF 0.0047uF
5.00% 5% 5.00% 5% 10%
C184 C185 C190 C191 C192
1-162-968-11 1-125-891-11 1-115-156-11 1-126-933-11 1-126-382-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT
0.0047uF 0.47uF 1uF 100uF 100uF
10% 50V 10.00% 10V 10V 20.00% 16V 20.00% 16V
C193 C194 C196 C197 C198
1-126-382-11 1-164-360-11 1-164-360-11 1-107-826-11 1-126-933-11
ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT
100uF 0.1uF 0.1uF 0.1uF 100uF
20.00% 16V 16V 16V 10.00% 16V 20.00% 16V
C199
1-162-962-11 CERAMIC CHIP
470PF
10%
< LED > LED302 LED303 LED304 LED305 LED306
8-719-051-17 8-719-051-17 8-719-051-17 8-719-051-17 8-719-051-17
DIODE DIODE DIODE DIODE DIODE
SLR-342DCT31 SLR-342DCT31 SLR-342DCT31 SLR-342DCT31 SLR-342DCT31
LED307 8-719-051-17 DIODE SLR-342DCT31 ************************************************************ A-4728-536-A CD BOARD, COMPLETE ******************* < CAPACITOR > C101 C102 C103 C104 C108
1-162-967-11 1-107-826-11 1-162-962-11 1-162-962-11 1-107-826-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.0033uF 0.1uF 470PF 470PF 0.1uF
10% 10.00% 10% 10% 10.00%
50V 16V 50V 50V 16V
C109 C110 C111 C112 C114
1-162-965-11 1-162-967-11 1-162-927-11 1-115-156-11 1-164-360-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.0015uF 10% 0.0033uF 10% 100PF 5% 1uF 0.1uF
C116 C117 C118 C121 C122
1-126-382-11 1-126-382-11 1-162-964-11 1-164-360-11 1-126-933-11
ELECT ELECT CERAMIC CHIP CERAMIC CHIP ELECT
100uF 100uF 0.001uF 0.1uF 100uF
20.00% 16V 20.00% 16V 10% 50V 16V 20.00% 16V
C123 C124 C125 C126 C127
1-162-970-11 1-125-891-11 1-164-360-11 1-164-360-11 1-126-382-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT
0.01uF 0.47uF 0.1uF 0.1uF 100uF
10% 25V 10.00% 10V 16V 16V 20.00% 16V
C130 C131 C133 C140 C143
1-164-360-11 1-126-933-11 1-162-921-11 1-115-156-11 1-164-360-11
CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 100uF 33PF 1uF 0.1uF
16V 20.00% 16V 5% 50V 10V 16V
C145 C146 C150 C153 C159
1-164-360-11 1-107-826-11 1-107-826-11 1-164-360-11 1-162-969-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 16V 0.1uF 10.00% 16V 0.1uF 10.00% 16V 0.1uF 16V 0.0068uF 10% 25V
25V 50V 25V 50V 50V
50V
< CONNECTOR > 50V 50V 50V 10V 16V
CN101 CN102
1-770-528-31 CONNECTOR, FFC/FPC 21P 1-779-553-21 CONNECTOR,FFC(LIF(NON-ZIF))16P < DIODE >
D101
8-719-056-77 DIODE UDZ-TE-17-3.9B < FERRITE BEAD >
FB101 FB103
1-469-144-21 FERRITE 1-469-144-21 FERRITE
0uH 0uH
< IC > IC101 IC102 IC103
8-752-402-31 IC CXD3017Q 8-759-549-28 IC BA5974FP-E2 8-752-089-74 IC CXA2581N-T4 < JUMPER RESISTOR >
JR101
1-216-864-11 METAL CHIP
0
5%
< TRANSISTOR >
36
Q101 Q102
8-729-049-31 TRANSISTOR 8-729-920-85 TRANSISTOR
2SB710A-RTX 2SD1664-T100-QR
1/16W
HCD-EP313 CD Ref. No.
Part No.
Description
Remarks
Ref. No.
1-216-821-11 1-216-845-11 1-216-835-11 1-216-839-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 100K 15K 33K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R107 R108 R109 R111 R114
1-216-833-11 1-216-827-11 1-216-857-11 1-216-846-11 1-218-745-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10K 3.3K 1M 120K 160K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/10W
R116 R117 R118 R119 R120
1-216-797-11 1-216-821-11 1-216-809-11 1-216-826-11 1-216-835-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10 1K 100 2.7K 15K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R122 R123 R124 R131 R143
1-216-845-11 1-216-833-11 1-216-845-11 1-216-813-11 1-216-836-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 10K 100K 220 18K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/10W 1/16W
R144 R147 R148 R149 R150
1-216-836-11 1-216-828-11 1-216-797-11 1-216-797-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
18K 3.9K 10 10 10K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R151 R158 R159 R162 R171
1-216-845-11 1-216-837-11 1-216-837-11 1-216-847-11 1-216-837-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 22K 22K 150K 22K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R172 R173 R181 R182 R183
1-216-837-11 1-216-837-11 1-216-837-11 1-216-837-11 1-216-837-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
22K 22K 22K 22K 22K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R190 R191 R192 R193 R194
1-216-813-11 1-216-839-11 1-216-839-11 1-216-846-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
220 33K 33K 120K 100K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R195 R196 R197
1-216-853-11 METAL CHIP 1-216-825-11 METAL CHIP 1-216-821-11 METAL CHIP
470K 2.2K 1K
5% 5% 5%
1/16W 1/16W 1/16W
Description
Remarks
A-4732-942-A CONTROL BOARD, COMPLETE (AEP,UK) ************************ A-4732-948-A CONTROL BOARD, COMPLETE (US,CND) ************************
< RESISTOR > R101 R102 R103 R104 R106
Part No.
CONTROL
4-245-258-01 HOLDER,LED < CAPACITOR > C301 C302 C303 C304 C305
1-124-259-11 1-126-960-11 1-162-966-11 1-126-964-11 1-124-584-00
C306 C307 C308 C309 C310
ELECT ELECT CERAMIC CHIP ELECT ELECT
4.7uF 1uF 0.0022uF 10uF 100uF
20.00% 20.00% 10% 20.00% 20%
35V 50V 50V 50V 10V
1-126-960-11 ELECT
1uF
20.00% 50V
1-164-227-11 CERAMIC CHIP 1-164-156-11 CERAMIC CHIP
0.022uF 0.1uF
10%
C311 C312 C313 C314 C315
1-162-920-11 CERAMIC CHIP 1-162-918-11 CERAMIC CHIP
27PF 18PF
5% 50V 5.00% 50V
1-126-926-11 ELECT 1-164-156-11 CERAMIC CHIP
1000uF 0.1uF
20.00% 10V 25V
C316 C317 C318 C319 C320
1-162-927-11 1-162-927-11 1-162-927-11 1-162-927-11 1-162-927-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
100PF 100PF 100PF 100PF 100PF
5% 5% 5% 5% 5%
C321 C322 C323 C324 C325
1-164-156-11 1-162-927-11 1-164-156-11 1-162-918-11 1-128-551-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT
0.1uF 100PF 0.1uF 18PF 22uF
C326 C327 C328 C329 C330
1-162-970-11 1-162-970-11 1-162-968-11 1-162-968-11 1-127-888-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC
0.01uF 0.01uF 0.0047uF 0.0047uF 0.1uF
10% 10% 10% 10% 10%
C331 C333 C334 C335 C336
1-164-156-11 1-164-156-11 1-162-921-11 1-162-917-11 1-162-925-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.1uF 33PF 15PF 68PF
25V 25V 5% 50V 5% 50V 5.00% 50V
C337 C338 C340
1-162-964-91 CERAMIC CHIP 1-164-156-11 CERAMIC CHIP
1000P 0.1uF
10%
25V 25V
50V 50V 50V 50V 50V
25V 50V 25V 5.00% 50V 20.00% 25V 5%
25V 25V 50V 50V 50V
50V 25V
< NETWORK RESISTOR > < CONNECTOR > RN101
1-233-576-11 RES, CHIP NETWORK 100 < SWITCH >
S101
CN301 CN302
1-568-864-11 CONNECTOR, FFC 21P 1-793-767-11 CONNECTOR, BOARD TO BOARD 30P < DIODE >
1-771-853-11 SWITCH, DETECTION (LIMIT IN) < VIBRATOR >
X101 1-767-226-11 VIBRATOR, CRYSTAL 16.9344MHz ************************************************************
D301 D302 D303 D304 D305
8-719-991-33 8-719-991-33 8-719-010-41 8-719-991-33 8-719-991-33
DIODE DIODE DIODE DIODE DIODE
1SS133T-72 1SS133T-72 UZ-5.6BSA-TP 1SS133T-72 1SS133T-72
37
HCD-EP313 CONTROL Ref. No. D306 D307 D308
Part No.
Description
Remarks
8-719-991-33 DIODE 1SS133T-72 8-719-991-33 DIODE 1SS133T-72 8-719-991-33 DIODE 1SS133T-72 < FERRITE BEAD >
FB301 FB303
1-400-297-11 INDUCTOR
0uH
< IC > IC301 IC302 IC303
6-802-783-01 IC LC877140A-51E2 6-700-250-01 IC PST3445UL 6-701-681-01 IC RPM7140-V4 < JUMPER RESISTOR >
JR301 JR302 JR303 JR304 JR305
1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
0 0 0 0 0
JR306 JR307 JR308 JR309 JR310
1-216-295-91 1-216-295-91 1-216-295-91 1-216-295-91 1-216-295-91
SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP
0 0 0 0 0
JR311 JR312 JR313 JR314 JR315
1-216-295-91 1-216-295-91 1-216-295-91 1-216-295-91 1-216-295-91
SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP
0 0 0 0 0
JR317 JR318 JR319 JR320
1-216-864-11 1-216-864-11 1-216-295-91 1-216-295-91
METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP
0 0 0 0
5% 5% 5% 5% 5%
5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
1/16W 1/16W
< COIL > L301 L302 L304
1-408-117-00 INDUCTOR
10uH
< LIQUID CRYSTAL DISPLAY > LCD301 1-805-184-11 DISPLAY PANEL, LIQUID CRYSTAL < LED > LED301 8-719-059-98 DIODE SLR-342VCT31 (STANDBY) < TRANSISTOR > Q301 Q302 Q303 Q304 Q305
8-729-230-49 8-729-230-49 6-550-296-01 8-729-230-49 8-729-230-49
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
Q306
8-729-900-53 TRANSISTOR
2SC2712L-TE85R 2SC2712L-TE85R 2SA1980G 2SC2712L-TE85R 2SC2712L-TE85R DTC114EK
< RESISTOR > R300 R301 R302 R303 R304
38
1-216-825-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
2.2K 1K 1K 1K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
Ref. No.
Part No.
Description
R305 R306 R307 R308 R309
1-216-821-11 1-216-821-11 1-216-809-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 1K 100 1K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
Remarks
R310 R311 R312 R313 R314
1-216-814-11 1-216-814-11 1-216-809-11 1-216-825-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
270 270 100 2.2K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R315 R316 R317 R318 R319
1-216-821-11 1-216-809-11 1-216-821-11 1-216-810-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP RES CHIP METAL CHIP
1K 100 1K 120 100
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/10W 1/16W
R320 R321 R322 R323 R324
1-216-809-11 1-216-809-11 1-249-417-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP CARBON METAL CHIP METAL CHIP
100 100 1K 1K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/4W F 1/16W 1/16W
R325 R326 R327 R328 R329
1-216-809-11 1-216-809-11 1-216-821-11 1-249-425-11 1-218-867-11
METAL CHIP METAL CHIP METAL CHIP CARBON METAL CHIP
100 100 1K 4.7K 6.8K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/4W F 1/10W
R330 R331 R332 R333 R334
1-249-427-11 1-216-828-11 1-216-828-11 1-249-422-11 1-249-422-11
CARBON METAL CHIP METAL CHIP CARBON CARBON
6.8K 3.9K 3.9K 2.7K 2.7K
5% 5% 5% 5% 5%
1/4W F 1/16W 1/16W 1/4W F 1/4W F
R335 R336 R337 R338 R339
1-216-824-11 1-249-420-11 1-249-429-11 1-216-833-11 1-216-834-11
METAL CHIP CARBON CARBON METAL CHIP METAL CHIP
1.8K 1.8K 10K 10K 12K
5% 5% 5% 5% 5%
1/16W 1/4W F 1/4W 1/16W 1/16W
R340 R341 R342 R344 R345
1-216-823-11 1-249-425-11 1-216-823-11 1-249-438-11 1-216-809-11
METAL CHIP CARBON METAL CHIP CARBON METAL CHIP
1.5K 4.7K 1.5K 56K 100
5% 5% 5% 5% 5%
1/16W 1/4W F 1/16W 1/4W 1/16W
R346 R347 R348 R349 R350
1-216-837-11 1-216-837-11 1-216-821-11 1-216-841-11 1-216-837-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
22K 22K 1K 47K 22K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R351 R352 R353 R354 R355
1-216-843-11 1-216-840-11 1-249-425-11 1-216-834-11 1-216-821-11
METAL CHIP METAL CHIP CARBON METAL CHIP METAL CHIP
68K 39K 4.7K 12K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/4W F 1/16W 1/16W
R356 R357 R358 R359 R360
1-216-821-11 1-216-821-11 1-216-817-11 1-245-191-21 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 1K 470 10K 10K
5% 5% 5% 1% 5%
1/16W 1/16W 1/16W 1/10W 1/16W
R361 R362 R363 R364 R365
1-216-809-11 1-216-821-11 1-216-833-11 1-216-821-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 1K 10K 1K 100K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
HCD-EP313 CONTROL Ref. No.
Remarks
Part No.
Description
Part No.
Description
R366 R367 R368 R369 R370
1-247-887-00 1-216-841-11 1-216-835-11 1-216-845-11 1-216-841-11
CARBON METAL CHIP METAL CHIP METAL CHIP RES CHIP
220K 47K 15K 100K 47K
5% 5% 5% 5% 5%
1/4W 1/16W 1/16W 1/16W 1/10W
C222 C223 C224 C225 C226
1-126-947-11 1-126-962-11 1-126-961-11 1-126-961-11 1-164-174-11
ELECT ELECT ELECT ELECT CERAMIC CHIP
47uF 3.3uF 2.2uF 2.2uF 0.0082uF
20.00% 20.00% 20.00% 20.00% 10%
R371 R372 R373 R374 R375
1-249-417-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-841-11
CARBON METAL CHIP METAL CHIP METAL CHIP RES CHIP
1K 100 100 100 47K
5% 5% 5% 5% 5%
1/4W F 1/16W 1/16W 1/16W 1/10W
C227 C228 C229 C230 C240
1-164-174-11 1-162-968-11 1-162-968-11 1-164-156-11 1-126-956-91
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT
0.0082uF 0.0047uF 0.0047uF 0.1uF 0.1uF
10% 10% 10%
25V 50V 50V 25V 20.00% 50V
R376 R377 R378 R379 R380
1-216-821-11 1-249-429-11 1-216-825-11 1-216-833-11 1-216-810-11
METAL CHIP CARBON RES CHIP METAL CHIP RES CHIP
1K 10K 2.2K 10K 120
5% 5% 5% 5% 5%
1/16W 1/4W 1/10W 1/16W 1/10W
C241 C242 C243 C248 C249
1-126-956-91 ELECT
0.1uF
20.00% 50V
1-164-156-91 CERAMIC CHIP
0.1uF
25V
C400 C415 C416 C417 C441
1-126-947-11 1-216-964-11 1-126-935-11 1-164-156-11 1-126-934-11
ELECT METAL ELECT CERAMIC CHIP ELECT
47uF 62K 470uF 0.1uF 220uF
20.00% 25V 1% 0.6W 20.00% 16V 25V 20.00% 10V
C442 C446 C447 C450 C451
1-164-156-11 1-126-947-11 1-164-156-11 1-164-156-11 1-164-156-11
CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 47uF 0.1uF 0.1uF 0.1uF
25V 20.00% 25V 25V 25V 25V
C452 C453 C454 C455 C456
1-126-934-11 1-162-979-11 1-162-979-11 1-162-979-11 1-162-970-11
ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
220uF 0.0027uF 0.0027uF 0.0027uF 0.01uF
20.00% 10.00% 10.00% 10.00% 10%
10V 50V 50V 50V 25V
C457 C461 C462 C501 C502
1-106-361-00 1-162-935-11 1-162-935-11 1-162-970-11 1-126-947-11
MYLAR CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT
0.0056uF 4PF 4PF 0.01uF 47uF
5.00% 0.25PF 0.25PF 10% 20.00%
100V 50V 50V 25V 25V
C540 C588 C601 C602 C603
1-164-230-11 1-126-934-11 1-164-730-11 1-164-730-11 1-126-961-11
CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT
220PF 220uF 0.0012uF 0.0012uF 2.2uF
5.00% 20.00% 10.00% 10.00% 20.00%
50V 10V 50V 50V 50V
C604 C611 C612 C613 C614
1-126-961-11 1-126-956-91 1-126-956-91 1-216-957-91 1-216-957-91
ELECT ELECT ELECT METAL METAL
2.2uF 0.1uF 0.1uF 33K 33K
20.00% 20.00% 20.00% 1% 1%
50V 50V 50V 0.6W 0.6W
C619 C620 C637 C638 C639
1-126-961-11 1-126-961-11 1-162-923-11 1-162-923-11 1-164-315-11
ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
2.2uF 2.2uF 47PF 47PF 470PF
20.00% 20.00% 5% 5% 5.00%
50V 50V 50V 50V 50V
C640 C641 C642 C643 C644
1-164-315-11 1-100-229-11 1-100-229-11 1-128-551-11 1-128-551-11
CERAMIC CHIP C-CAP, U C-CAP, U ELECT ELECT
470PF 5.00% 50V 6800P-50 K B GRM 6800P-50 K B GRM 22uF 20.00% 25V 22uF 20.00% 25V
C645 C646 C647 C648 C649
1-162-970-11 1-162-970-11 1-100-229-11 1-100-229-11 1-164-218-11
CERAMIC CHIP CERAMIC CHIP C-CAP, U C-CAP, U CERAMIC CHIP
0.01uF 10% 25V 0.01uF 10% 25V 6800P-50 K B GRM 6800P-50 K B GRM 180PF 0.25PF 50V
< SWITCH > S301 S302 S303 S304 S305
1-786-050-21 1-786-050-21 1-786-050-21 1-786-050-21 1-786-050-21
SWITCH, KEY BOARD (CD) SWITCH, KEY BOARD (DISPLAY) SWITCH, KEY BOARD (MD) SWITCH, KEY BOARD (TUNER) SWITCH, KEY BOARD (>)
S306 S307 S308 S309 S310
1-786-050-21 1-786-050-21 1-786-050-21 1-786-050-21 1-786-050-21
SWITCH, KEY BOARD (DSG) SWITCH, KEY BOARD (.) SWITCH, KEY BOARD (BASS/TRE) SWITCH, KEY BOARD (x) SWITCH, KEY BOARD (M)
S311 S312 S313 S314 S315
1-786-050-21 1-786-050-21 1-786-050-21 1-786-050-21 1-786-419-11
SWITCH, KEY BOARD (l/ 1) SWITCH, KEY BOARD (m) SWITCH, KEY BOARD (X) SWITCH, KEY BOARD (PLAY/MODE) SW, RTRY RE121PVB25FINB1-24E (VOLUME) < VIBRATOR >
X301 9-300-001-87 VIB,XTAL 32.768KHZ CFS-308 CT X302 1-795-880-11 VIBRATOR, CERAMIC 8.64MHz ************************************************************ A-4732-950-A MAIN BOARD, COMPLETE (US,CND) ********************* A-4732-945-A MAIN BOARD, COMPLETE (AEP,UK) ********************* 7-685-546-14 SCREW +BTP
3X8
TYPE2 N-S
< CAPACITOR > C200 C201 C202 C203 C204
1-126-941-11 1-164-156-11 1-162-968-11 1-162-970-11 1-162-970-11
ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
470uF 0.1uF 0.0047uF 0.01uF 0.01uF
20.00% 25V 25V 10% 50V 10% 25V 10% 25V
C205 C206 C207 C208 C209
1-162-970-11 1-128-548-11 1-164-156-11 1-130-495-00 1-104-666-11
CERAMIC CHIP ELECT CERAMIC CHIP MYLAR ELECT
0.01uF 4700uF 0.1uF 0.1uF 220uF
10% 20%
25V 25V 25V 5% 50V 20.00% 25V
C210 C211 C212 C213 C221
1-130-495-00 1-130-495-00 1-130-495-00 1-130-495-00 1-126-960-11
MYLAR MYLAR MYLAR MYLAR ELECT
0.1uF 0.1uF 0.1uF 0.1uF 1uF
5% 5% 5% 5% 20.00%
50V 50V 50V 50V 50V
Ref. No.
MAIN Remarks 25V 50V 50V 50V 25V
39
HCD-EP313 MAIN Ref. No.
Part No.
Description
Part No.
Description
C650 C651 C652 C660 C663
1-164-218-11 1-126-961-11 1-126-961-11 1-162-927-11 1-164-156-11
CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP
180PF 2.2uF 2.2uF 100PF 0.1uF
0.25PF 20.00% 20.00% 5%
Remarks 50V 50V 50V 50V 25V
Ref. No. D404 D405 D501 D602 D603
8-719-991-33 8-719-109-89 8-719-991-33 8-719-109-85 8-719-109-85
DIODE DIODE DIODE DIODE DIODE
1SS133T-72 MTZJ-T-72-5.6B 1SS133T-72 MTZJ-T-72-5.1B MTZJ-T-72-5.1B
Remarks
C665 C666 C667 C668 C670
1-162-970-11 1-126-935-11 1-104-665-11 1-162-970-11 1-162-967-11
CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP
0.01uF 470uF 100uF 0.01uF 0.0033uF
10% 20.00% 20.00% 10% 10%
25V 10V 10V 25V 50V
D801 D802 D803 D804
8-719-923-60 8-719-991-33 8-719-923-60 8-719-991-33
DIODE DIODE DIODE DIODE
MTZJ-T-77-9.1A 1SS133T-72 MTZJ-T-77-9.1A 1SS133T-72
C671 C681 C682 C683 C684
1-162-967-11 1-162-966-11 1-162-966-11 1-110-563-11 1-110-563-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.0033uF 0.0022uF 0.0022uF 0.068uF 0.068uF
10% 10% 10% 10% 10%
50V 50V 50V 16V 16V
C700 C705 C706 C708 C709
1-126-947-11 1-126-963-11 1-162-970-11 1-126-947-11 1-162-970-11
ELECT ELECT CERAMIC CHIP ELECT CERAMIC CHIP
47uF 4.7uF 0.01uF 47uF 0.01uF
20.00% 20.00% 10% 20.00% 10%
25V 50V 25V 25V 25V
C800 C801 C802 C803 C804
1-126-961-11 1-126-961-11 1-162-964-11 1-162-964-11 1-162-970-11
ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
2.2uF 2.2uF 0.001uF 0.001uF 0.01uF
20.00% 20.00% 10% 10% 10%
50V 50V 50V 50V 25V
C805 C806 C807 C808 C809
1-162-970-11 1-126-935-11 1-162-970-11 1-126-963-11 1-126-963-11
CERAMIC CHIP ELECT CERAMIC CHIP ELECT ELECT
0.01uF 470uF 0.01uF 4.7uF 4.7uF
10% 20.00% 10% 20.00% 20.00%
25V 16V 25V 50V 50V
C814 C815 C816 C817
1-165-176-11 1-126-933-11 1-162-970-11 1-165-176-11
CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP
0.047uF 100uF 0.01uF 0.047uF
10% 20.00% 10% 10%
16V 16V 25V 16V
< FERRITE BEAD >
< CONNECTOR > CN202 * CN305 * CN501 * CN502 CN701
1-793-766-11 1-564-704-11 1-564-710-11 1-564-709-11 1-568-830-11
CONNECTOR, BOARD TO BOARD 30P PIN, CONNECTOR (SMALL TYPE) 2P PIN, CONNECTOR (SMALL TYPE) 8P PIN, CONNECTOR (SMALL TYPE) 7P CONNECTOR, FFC 11P
FB201 FB202 FB401 FB701 FB710
1-400-297-11 INDUCTOR 1-400-297-11 INDUCTOR
0uH 0uH
< IC > IC200 IC204 IC601 IC800
8-759-231-53 6-704-060-01 6-702-895-01 8-759-167-88
IC IC IC IC
TA7805S LA4636 BD3881FV NJM4565D
< JACK > J201 J202 J203
1-793-484-11 JACK, PIN 2P 1-816-219-11 JACK, HEADPHONE 1-536-708-81 TERMINAL BOARD, PUSH (4P) (SPEAKER) < COIL >
L200 L201 L202 L203 L204
1-400-297-11 1-456-107-11 1-456-107-11 1-456-107-11 1-456-107-11
INDUCTOR COIL, K (MDEC) COIL, K (MDEC) COIL, K (MDEC) COIL, K (MDEC)
L205 L451
1-408-117-00 INDUCTOR 1-456-094-11 COIL, OSC
0uH
10uH 85KHZ BIAS
< CARBON > 0 PR200 0 PR501
1-249-385-11 CARBON 1-249-385-11 CARBON
2.2 2.2
5% 5%
1/6W F 1/6W F
< TRANSISTOR > < DIODE > D200 D201 D202 D203 D204
6-500-376-01 6-500-378-01 6-500-378-01 6-500-378-01 6-500-378-01
DIODE DIODE DIODE DIODE DIODE
1N4003LES 1N5402GW(F20) 1N5402GW(F20) 1N5402GW(F20) 1N5402GW(F20)
D205 D206 D207 D208 D209
8-719-991-33 8-719-991-33 8-719-991-33 8-719-991-33 8-719-991-33
DIODE DIODE DIODE DIODE DIODE
1SS133T-72 1SS133T-72 1SS133T-72 1SS133T-72 1SS133T-72
D210 D211 D212 D213 D403
8-719-991-33 8-719-991-33 8-719-991-33 8-719-991-33 8-719-109-97
DIODE DIODE DIODE DIODE DIODE
1SS133T-72 1SS133T-72 1SS133T-72 1SS133T-72 MTZJ-T-77-6.8B
Q200 Q205 Q206 Q400 Q401
8-729-230-49 6-550-333-01 6-550-333-01 8-729-120-28 8-729-120-28
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
2SC2712L-TE85R 2SC5343GL 2SC5343GL 2SC3052F-T1-LF 2SC3052F-T1-LF
Q402 Q403 Q404 Q405 Q406
8-729-024-94 6-550-296-01 6-550-333-01 6-550-333-01 6-550-344-01
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
2SB1370-EF 2SA1980G 2SC5343GL 2SC5343GL 2SC3266GR
Q450 Q451 Q453 Q454 Q501
8-729-120-28 6-550-333-01 6-550-333-01 6-550-333-01 8-729-901-97
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
2SC3052F-T1-LF 2SC5343GL 2SC5343GL 2SC5343GL 2SA1036K-T-147-Q
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
40
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
HCD-EP313 MAIN Ref. No.
Part No.
Description
Part No.
Description
Q502 Q504 Q505 Q506 Q507
6-550-296-01 8-729-901-05 8-729-045-62 8-729-901-05 8-729-045-62
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
2SA1980G DTA124EK 2SK2158-T2B DTA124EK 2SK2158-T2B
Remarks
R441 R442 R443 R444 R445
1-216-817-11 1-249-425-11 1-216-807-11 1-249-429-11 1-216-822-11
METAL CHIP CARBON METAL CHIP CARBON METAL CHIP
470 4.7K 68 10K 1.2K
5% 5% 5% 5% 5%
1/16W 1/4W F 1/16W 1/4W 1/16W
Q508 Q509 Q510 Q511 Q601
8-729-045-62 8-729-216-22 8-729-216-22 1-809-869-11 8-729-030-03
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
2SK2158-T2B 2SA1162-G 2SA1162-G DTA124EL-TL2 DTC144ESA-TP
R446 R447 R453 R454 R455
1-216-818-11 1-216-821-11 1-216-825-11 1-249-392-11 1-216-836-11
METAL CHIP METAL CHIP METAL CHIP CARBON METAL CHIP
560 1K 2.2K 8.2 18K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/4W F 1/16W
Q602 Q701 Q702 Q801 Q802
8-729-030-03 6-550-305-01 8-729-030-03 8-729-920-31 8-729-920-31
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
DTC144ESA-TP 2SA1296GR DTC144ESA-TP DTC343TK DTC343TK
R456 R458 R459 R460 R465
1-216-836-11 1-216-829-11 1-216-842-11 1-216-845-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
18K 4.7K 56K 100K 10K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
Q803 Q804
6-550-296-01 TRANSISTOR 8-729-029-69 TRANSISTOR
2SA1980G DTC114TSA-TP
R466 R467 R470 R502 R503
1-216-833-11 1-216-833-11 1-249-393-11 1-249-409-11 1-216-864-11
METAL CHIP METAL CHIP CARBON CARBON METAL CHIP
10K 10K 10 220 0
5% 5% 5% 5% 5%
1/16W 1/16W 1/4W F 1/4W F 1/16W
R504 R505 R525 R527 R528
1-216-821-11 1-216-825-11 1-216-857-11 1-249-436-11 1-216-828-11
METAL CHIP METAL CHIP METAL CHIP CARBON METAL CHIP
1K 2.2K 1M 39K 3.9K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/4W 1/16W
R530 R593 R594 R599 R603
1-216-833-11 1-249-429-11 1-249-429-11 1-249-421-11 1-216-840-11
METAL CHIP CARBON CARBON CARBON METAL CHIP
10K 10K 10K 2.2K 39K
5% 5% 5% 5% 5%
1/16W 1/4W 1/4W 1/4W F 1/16W
R604 R609 R610 R611 R612
1-216-840-11 1-216-827-11 1-216-827-11 1-249-432-11 1-249-432-11
METAL CHIP METAL CHIP METAL CHIP CARBON CARBON
39K 3.3K 3.3K 18K 18K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/4W 1/4W
R613 R617 R618 R619 R620
1-216-829-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
4.7K 1K 1K 1K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R633 R634 R635 R636 R637
1-218-867-11 1-218-867-11 1-216-808-11 1-216-808-11 1-216-817-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
6.8K 6.8K 82 82 470
5% 5% 5% 5% 5%
1/10W 1/10W 1/16W 1/16W 1/16W
R638 R639 R640 R641 R642
1-216-817-11 1-216-826-11 1-216-826-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
470 2.7K 2.7K 1K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R643 R644 R645 R646 R647
1-216-821-11 1-216-821-11 1-216-833-11 1-216-833-11 1-216-825-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 1K 10K 10K 2.2K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R648 R649 R650 R651
1-216-825-11 1-216-836-11 1-249-432-11 1-216-822-11
METAL CHIP METAL CHIP CARBON METAL CHIP
2.2K 18K 18K 1.2K
5% 5% 5% 5%
1/16W 1/16W 1/4W 1/16W
< RESISTOR > R200 R201 R202 R203 R204
1-249-398-11 1-216-829-11 1-216-822-11 1-247-807-31 1-249-385-11
CARBON METAL CHIP METAL CHIP CARBON CARBON
27 4.7K 1.2K 100 2.2
5% 5% 5% 5% 5%
1/4W F 1/16W 1/16W 1/4W 1/6W F
R205 R206 R207 R208 R209
1-249-385-11 1-249-385-11 1-249-385-11 1-249-429-11 1-249-429-11
CARBON CARBON CARBON CARBON CARBON
2.2 2.2 2.2 10K 10K
5% 5% 5% 5% 5%
1/6W F 1/6W F 1/6W F 1/4W 1/4W
R221 R222 R223 R224 R225
1-216-839-11 1-216-841-11 1-216-837-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
33K 47K 22K 1K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R226 R227 R228 R229 R230
1-216-821-11 1-216-821-11 1-216-825-11 1-216-825-11 1-249-427-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP CARBON
1K 1K 2.2K 2.2K 6.8K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/4W F
R231 R232 R233 R234 R237
1-249-427-11 1-216-822-11 1-216-822-11 1-249-433-11 1-216-864-11
CARBON METAL CHIP METAL CHIP CARBON METAL CHIP
6.8K 1.2K 1.2K 22K 0
5% 5% 5% 5% 5%
1/4W F 1/16W 1/16W 1/4W 1/16W
R238 R239 R240 R241 R245
1-216-864-11 1-216-222-00 1-216-825-11 1-216-825-11 1-216-840-11
METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP
0 10K 2.2K 2.2K 39K
5% 5% 5% 5% 5%
1/16W 1/8W 1/16W 1/16W 1/16W
R246 R247 R248 R400 R401
1-216-840-11 METAL CHIP
39K
5%
1/16W
1-216-825-11 METAL CHIP 1-216-825-11 METAL CHIP
2.2K 2.2K
5% 5%
1/16W 1/16W
R402 R403 R404 R405 R406
1-216-841-11 1-216-857-11 1-216-833-11 1-216-821-11 1-216-828-11
47K 1M 10K 1K 3.9K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
Ref. No.
Remarks
41
HCD-EP313 MAIN Ref. No.
TRANSFORMER Part No.
Description
Remarks
R652
1-216-822-11 METAL CHIP
1.2K
5%
1/16W
R655 R656 R657 R658 R660
1-216-836-11 1-216-836-11 1-216-852-11 1-216-852-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
18K 18K 390K 390K 10K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R662 R665 R672 R673 R674
1-216-829-11 1-249-413-11 1-216-833-11 1-216-833-11 1-249-429-11
METAL CHIP CARBON METAL CHIP METAL CHIP CARBON
4.7K 470 10K 10K 10K
5% 5% 5% 5% 5%
1/16W 1/4W F 1/16W 1/16W 1/4W
R675 R681 R682 R688 R689
1-249-429-11 1-216-825-11 1-216-825-11 1-216-843-11 1-216-843-11
CARBON METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10K 2.2K 2.2K 68K 68K
5% 5% 5% 5% 5%
1/4W 1/16W 1/16W 1/16W 1/16W
R694 R695 R696 R697 R698
1-249-413-11 1-249-438-11 1-249-438-11 1-216-842-11 1-216-842-11
CARBON CARBON CARBON METAL CHIP METAL CHIP
470 56K 56K 56K 56K
5% 5% 5% 5% 5%
1/4W F 1/4W 1/4W 1/16W 1/16W
R701 R702 R705 R706 R708
1-216-864-11 METAL CHIP 1-216-864-11 METAL CHIP 1-216-864-11 METAL CHIP
0 0 0
5% 5% 5%
1/16W 1/16W 1/16W
1-216-864-11 METAL CHIP
0
5%
1/16W
R709 R710 R711 R712 R713
1-216-864-11 1-216-837-11 1-216-837-11 1-216-825-11 1-216-864-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
0 22K 22K 2.2K 0
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R714 R800 R801 R802 R803
1-216-864-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
0 10K 10K 10K 10K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R804 R805 R806 R807 R810
1-216-820-11 1-216-829-11 1-216-829-11 1-216-820-11 1-216-825-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
820 4.7K 4.7K 820 2.2K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
Ref. No.
Part No.
Description
Remarks
< COIL > 0 L901 < TRANSFORMER > 0 PT901 0 PT902 0 PT902
1-439-734-11 TRANSFORMER, POWER (US,CND) 1-439-735-11 TRANSFORMER, POWER (AEP,UK) < RESISTOR >
0 R901
1-219-236-51 RES SOLID
2.2M
20%
1/2W
< RELAY > 0 RY901 1-755-276-11 RELAY, POWER ************************************************************ MISCELLANEOUS ************** 08 08 68 106 0 604
1-555-795-00 1-783-532-11 1-796-689-11 1-757-055-11 8-820-053-03
M102 0 T901 0 T901
X-2625-769-1 GEAR ASSY (MB) (RP), MOTOR (SLED) 1-439-656-11 TRANSFORMER, POWER (US,CND) 1-439-657-11 TRANSFORMER, POWER (AEP,UK)
CORD, POWER (AEP,UK) CORD, POWER (US,CND) DECK MECHANICAL WIRE, PARALLEL (FFC) (16 CORE) OPTICAL PICK-UP KSS-213E/C2N
R811 1-216-821-11 METAL CHIP 1K 5% 1/16W R814 1-249-404-00 CARBON 82 5% 1/4W F R815 1-249-404-00 CARBON 82 5% 1/4W F R816 1-249-407-11 CARBON 150 5% 1/4W F R817 1-216-823-11 RES CHIP 1.5K 5% 1/10W ************************************************************ 1-688-570-11 TRANSFORMER BOARD ******************* < CAPACITOR > C901
1-126-941-11 ELECT
470uF
20.00% 25V
< DIODE > D901 D902 D903 D904
42
8-719-991-33 8-719-991-33 8-719-991-33 8-719-991-33
DIODE DIODE DIODE DIODE
1SS133T-72 1SS133T-72 1SS133T-72 1SS133T-72
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
HCD-EP313
MEMO
43
HCD-EP313
REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver.
Date
1.0
2003.04
Description of Revision New
