Transcript
ULTRA 180 ARM INSTALLATION If you have any questions, please call 1-800-558-4435
IF MOUNTING TO THE ULTRA WALL TRACK a MOUNT ULTRA TRACK TO WALL
Remove small socket head cap screw in the top middle of the Wall Track. Remove plastic cover.
Locate the wall stud and mark the top hole of the Wall Track, drill 11/64 pilot hole and insert #14 screw and tighten slightly. Use a level, mark the lower holes, drill pilot holes and then insert the #14 screws. NOTE: #14 Wood screws are supplied with unit. If installing into metal studs, you will need to replace these with proper metal stud fasteners
b
ATTACH SLIDER TO ULTRA TRACK Insert Slider into Wall Track as shown at left and replace the small socket head cap screw and plastic cover.
Once you have adjusted the slider to the desired height, tighten down the Track Slider using the handle on the slider as shown. Once tight, make sure the handle is positioned so that it is pointing down as far as possible. Pull and turn handle to position.
IF MOUNTING TO A DESK ATTACH DESKMOUNT TO DESK Drill a 3/8 hole through the horizontal surface you intend to mount to and push the 3/8 stud on the desk mount through the hole. Slip the large mounting washer over the stud from underneath, add the 3/8 splitwasher, and secure in place with the 3/8 nylock.
Page 1 of 4
Desk Screw stud into desk mount
Washer
Desk Nylock
ULTRA 180 ARM INSTALLATION - rev 04/09/14 pjm
ULTRA 180 ARM INSTALLATION IF MOUNTING TO A WALL ATTACH WALL PLATE TO WALL Locate the stud and mark the top hole, drill 11/64 pilot hole and insert #14 screw and tighten slightly. Using a level, mark the lower hole and drill pilot hole, insert #14 screw and, with the unit level, tighten both screws.
W2
W3
NOTE: ICW supplies #14 wood screws. If installing onto metal studs, you will need to replace with proper metal stud fasteners.
IF MOUNTING TO A POLE ATTACH POLE CLAMP TO POLE
Using the 1/4” hex key, separate the two halves of pole mount as shown, place around pole at the desired height and reassemble.
IF USING EV65 ATTACH VESA TO MONITOR Attach the monitor mount assembly to the back of your monitor, using the 4mm screws provided.
Page 2 of 4
ATTACH VESA TO EV65 JOINT Insert stubs on VESA plate into holes in the Ergovision joint assembly. Insert 5/16 x 3/4 socket cap screws provided in both sides and tighten. Use the handle under mount to loosen tilt friction and adjust monitor tilt.
Socket cap screw
VESA plate
ULTRA 180 ARM INSTALLATION - rev 04/09/14 pjm
ULTRA 180 ARM INSTALLATION IF USING EV710 ATTACH BALL VESA
ATTACH VESA TO MONITOR
Mount the VESA assembly to the slide rails. Screw the slider knob through the rails and into the VESA assembly as shown.
Attach VESA to monitor using four 4mm screws in the hardware bag.
ADJUST BALL VESA HEIGHT & TENSION 1. To adjust the height of monitor, loosen slider knob, set monitor height on slider rails, then tighten knob.
Slider knob
2. To adjust pivot tension, gently and evenly tighten or loosen the four screws on the back of the ball VESA.
Pivot tension adjustment screws
IF ATTACHING TO ULTRA FLIP-UP
IF ATTACHING TO QUICK DISCONNNECT
ATTACH FLIP UP
ATTACH QUICK DISCONNECT
1. Remove screws from drop extension using 5/32” hex key. 2. Align holes in keyboard tray with screw holes in drop extension. 3. Attach keyboard tray using the provided screws.
1. Remove beauty cap on quick disconnect block. 2. Remove screw using 3/16” hex key. 3. Slide keyboard tray into quick disconnect block. 4. Replace screw and tighten. 5. Replace beauty cap.
Page 3 of 4
Beauty cap Screw
ULTRA 180 ARM INSTALLATION - rev 04/09/14 pjm
ULTRA 180 ARM INSTALLATION ULTRA CORD MANAGEMENT 1. Prepare all cables to route within the arm by placing them near cavity of arm and bundling together if necessary. 2. Remove cover by unscrewing four socket head cap screws. Screws are captured by the cover so they cannot fall out. Once screws are disengaged, pull cover out of arm. 3. Place cables within the channel. Do not block the holes where screws will engage in arm. 4. Replace cover and tighten screws. Cables should be able to pull through to desired position if necessary.
ULTRA 180 ARM CABLE MANAGEMENT RUN CABLES THROUGH UL180 ARM
STORE CABLE INSIDE COVER PLATE
1. Cover plate is spring loaded. Loosen cover plate screws on side of arm just enough to fit cables through gap. 2. Run cables loosely between cover plate and arm. Cables can be run on either or both sides of the arm. 3. Push cover plate against arm and tighten screws, being careful not to pinch cables.
Extra cable can be looped inside the cover plate to provide a neater appearance and simplify cleaning.
ADJUSTING ARM TENSION IMPORTANT Extend the UL180 straight out and be sure all equipment is mounted on the arm before adjusting he arm’s resistance. Use the T-handle provided to adjust the arms’ resistance. Do not use power tools to adjust.
Page 4 of 4
ADJUST UL180 ARM TENSION Using the 3/16” T-handle hex wrench provided, turn the screw in the UL180 arm clockwise to lighten the arm’s load resistance, or counter-clockwise to increase the load resistance.
ULTRA 180 ARM INSTALLATION - rev 04/09/14 pjm
