Transcript
IMPORTANT-READ THIS BEFORE RUNNING
1.Before Starting •Please read manual carefully (With a parent, guardian or a responsible adult if necessary).
Included Items
TOOLS NOT INCLUDED IN THE KIT
1.5mm Allen Wrench
2mm Allen Wrench
2.5mm Allen Wrench Cutter CurvedScissors
Craft Knife
Needle Nosed Pliers
PrecisionCaliper
Equipment Needed
2.While Operating •Any running area you choose must be dry. Do not run vehicle near any water or wet areas. •Do not run on public streets. It is very easy to have the car run over or be damaged by hitting the curb. •Do not operate the car in tight confined places. The vehicle is very fast and will easily hit something. •Do not run near people or animals. The car is very fast and could easily seriously injured someone.
•Do not operate the car at night. You will not be able to drive it safely.
3.Before Operating •Make sure that all screws and nuts are properly tightened. •Always use fresh batteries for your transmitter and receiver before running the car. If the radio does not have full control of the car with steering, throttle and brake. Do not run it until corrected. Failure to correct this will result in possible injury and damage to the car or property.
•Please confirm the steering and throttle is at neutral position.
4.Check Your Vehicle After Runing •Turn OFF receiver first, then turn OFF transmitter. This will prevent the car from losing control. •After running radio controlled car, it is necessary to perform routine maintenance.
5.Battery Safety •Please be careful when handling the battery. It will be hot after running. If the wire is frayed, a short circuit can cause a fire.
WARNING : To avoid a possible fire hazard, always unplug the battery. Do not leave your vehicle unattended with the battery plugged.
OVERVIEW
OVERVIEW Components Radio Control Car
Parts Bag
TOOLS NOT INCLUDED IN THE KIT Screw Cement
CA
Screw Cement
Body Reamer
Instant Cemment
GEAR GREASE
Curved Scissors Cutter Gear Grease
Craft Knife
Needle Nosed Pliers
Precision Caliper
Equipment Needed UM-3 "AA" type Batteries ( 8pcs ) Transmitter
Brushless Electric Speed Controller
Brushless Motor
Servo
7.4V L i-Po Battery (Hard Case) Receiver
L i-Po Battery Charger
1 ASSEMBLY OF THE FRONT AND REAR DIFF. Builds two differentials for front and rear. Step 2
Step 1 30779 2x12.8mm Pin
30769 .....x4 30751
30779 30777
30901 Oil
94034 4x4mm Set Screw
.....x2 30620
30620 30751
Oil 30777 P5 O-Ring
30901 .....x4 30769
30777
30779
30779 4X4mm 30620 7x19x6mm Ball Bearing .....x4
2 ASSEMBLY OF THE FRONT AND REAR DIFF. Builds two differentials for front and rear. Tighten Step 1
Step 2 30773
30769 30776 3x12mm Tight the diff. screws in this order.
30776 4x10mm Washer .....x8
94004 3x12mm Hex Screw
1
3
4
2
.....x8
Diff. Oil
30773 4mm Cross Pin
*Put the diff. oil approx 80%.
.....x4
3 ASSEMBLY OF THE FRONT AND REAR BEVEL GEARS Builds two differentials for front and rear.
Step 1
*Push 3mm tubes into the holes of the diff. Case.
Step 2 30121
30121 4x3x3mm Chromed Tube .....x8
30121 3x5mm Screw
.....x8
30121 30121 3x5mm
1
4 ASSEMBLY OF THE GEAR BOX AND FRONT SHOCK STAY Step 1
Step 2 5x5mm
94036 5x4mm Set Screw
.....x1
ew t Scermen C
30010 30630
30082
30262
30630 6x13x5mm Ball Bearing Apply Grease
.....x2
30630
4x10mm
30130 30010 94009 4x10mm Hex Screw
.....x2 3x25mm
94023 3x25mm Flat Head Screw
.....x2
94029 4x25mm Flat Head Screw
.....x2
4x25mm
5 ASSEMBLY OF THE FRONT LOWER ARMS
3mm
3mm 36870 4x10mm Set Screw
.....x2 Ensure Free Movement
94011 4x16mm Hex Screw
36171
4x10mm
36890 .....x2
36171 3mm
30160 Ensure Free Movement
*A 4x10mm set screw is used to adjust the ride-height.
4x16mm
36890
6 ASSEMBLY OF THE FRONT UPPER ARMS 3mm
Ensure Free Movement
94010 4x12mm Hex Screw
36905
36900 36640
.....x2
36905
30654 3mm
Caster Adjuster
4x12mm
2
*Caster angle will become bigger.
*Caster angle will become less.
7 ASSEMBLY OF THE FRONT KNUCKLE ARMS Assembly for both right and left side.
Step 1
Step 2
*Notice the direction of the plastic washer.
36901 94036 5x5mm Set Screw
.....x2 Ensure Free Movement
36903 36055 2.5x16.8mm Pin
L
36905 .....x2
Do Not Over Tighten
36052 36053
36903
36904
36053 36053 8x16x5mm Ball Bearing .....x4
30656 36905
Do Not Over Tighten
S Cecre m w en t
5x4mm 36055
8 ASSEMBLY OF THE FRONT KNUCKLE AND FRONT SUSPENSION ARMS Assembly for both right and left side.
* Put the drive shaft into cup joint before assembly.
9 ASSEMBLY OF THE FRONT STABILIZER Assembly for both right and left side.
3x8mm Set Screw .....x2
30403 6mm Ball .....x2 Makes two rods for left and right hand-side. 3x16mm Hex Screw
40029 .....x2 30341
94035 3x8mm
40199 94005 3x16mm
3
30403
10 ASSEMBLY OF THE FRONT STABILIZER
94033 3x3mm Set Screw
.....x2
94002 3x8mm Hex Screw
.....x2
3x3mm
Screw t Cemen
S Cecrew me nt
3x3mm
Ensure Free Movement
30261 94040 3x8x0.8mm
3x8mm
11 ASSEMBLY OF THE SERVO SAVER 36740
36740
Step 1
Step 2
Step 3 3x16mm
94041 M3 Nylon Nut
36743 6mm E-Ring
94005 3x16mm Hex Screw
.....x2
36743 6mm
36740
36742
36740
36743 6mm
36741
.....x4
36740
Ensure Free Movement
8x12x1mm 30361
.....x2 30361
30658 M3 Nylon Nut
36743 6mm 36743 6mm
12 ASSEMBLY OF THE SERVO SAVER AND THE STEERING TIE-ROD 3x15mm 3x10mm Step 1
3x15mm
Step 2
3x10mm 30272
94003 3x10mm Hex Screw
.....x3 34014
94021 3x15mm Flat Head Screw
36850
.....x2
36700 36790
40038
1:1 *Approx. 33.5mm *3 ùm 5 ¬ 3 .
30380
4
13 ASSEMBLY OF THE SERVO SAVER ONTO THE FRONT GEAR BOX
94041 M3 Nylon Nut
.....x2 3x15mm
94003 3x10mm Hex Screw
.....x2
94021 3x15mm Flat Head Screw
.....x2
3mm
3x10mm
40039
3x15mm
3mm
40039
14 ASSEMBLY OF THE GEAR BOX AND REAR SHOCK STAY Step 1
Step 2 5x5mm
94036 5x5mm Set Screw
.....x1
ew t Scermen C
3mm
30010 30630
34009
30082 30630 6x13x5mm Ball Bearing .....x2
Apply Grease
30630
3x16mm
30130
30010
94005 3x16mm Hex Screw
.....x2
94022 3x18mm Flat Head Screw
.....x2
94029 4x25mm Flat Head Screw
.....x2
3x18mm
4x25mm
15 ASSEMBLY OF THE REAR LOWER ARMS 3mm *A 4x10mm set screw is used to adjust ride-height. 36870 4x10mm Set Screw
3mm .....x2 Ensure Free Movement
34035 94027 4x16mm Flat Head Screw
4x10mm
36171
.....x2
3mm
30351
Ensure Free Movement
4x16mm
34035
5
16 ASSEMBLY OF THE REAR SUSPENSION ARMS
94036 5x5mm Set Screw
Assembly for both right and left side.
36081 36055 .....x2 36082 36053
94001 3x4mm Hex Screw
5x5mm .....x2
36053 36054 40028
36053 8x16x5mm Ball Bearing .....x4
36055 2.5x16.8mm Pin .....x2
3x4mm 34055
34035
17 ASSEMBLY OF THE REAR SUSPENSION ARMS Step 1
36850 7mm Ball
.....x4
3mm
Step 2
40065
.....x4
94041 3mm Nylon Nut
Ensure Free Movement
40065
36850 36861
94006 3x18mm Hex Screw
.....x2 36850
94008 3x25mm Hex Screw
3mm 3x18mm
.....x2 3x25mm *Approx. 21mm
1:1
Assembly for both right and left side.
18 ASSEMBLY OF THE REAR STABILIZER
94035 3x8mm Set Screw
Assembly for both right and left side.
.....x2
30403 6mm Ball .....x2 Makes two rods for left and right hand-side.
94006 3x18mm Hex Screw
.....x2
30341
40029
3x8mm
40199 30403
3x18mm
6
19 ASSEMBLY OF THE REAR STABILIZER
94033 3x3mm Set Screw
.....x2
94022 3x8mm Hex Screw
.....x2
3x3mm
ewnt Scrm e Ce
S Cecre m w en t
3x3mm
Ensure Free Movement
34027
3x8x0.8mm 3x8mm
20 ASSEMBLY OF THE REAR BODY POST
Step 1
Step 2 3mm
31159
M2 Nut
33011
.....x2
94041 M3 Nylon Nut
Choose the correct body post pin hole for your body.
3mm 33011
.....x2 33011
31159
2x18mm Screw .....x2
94005 3x16mm Hex Screw
3x16mm
33010 .....x2
2mm 3x16mm
w t re e n Sc em C
S Cecrew me nt
2x18mm
21 ASSEMBLY OF THE ONE SPEED TRANSMISSION INTO THE CENTER MOUNT 10mm
Step 1
94036 5x5mm Set Screw
35222 .....x3
30170
33020 Step 3 30620
94002 3x8mm Hex Screw
0 .....x4
5
10
15
r ew t Scemen C
ewnt Scrm e Ce
5x4mm
5x5mm 30201 Step 2 30110 30170 S Cecre m w en t
ew t Scermen C
3x8mm
5x4mm
30620
22 ASSEMBLY OF THE SINGLE SPEED MOUNT 3x12mm
Step 1 30652 94033 3x3mm Set Screw
.....x1
94004 3x12mm Hex Screw
.....x4
94005 3x15mm Hex Screw
Included Items
TOOLS NOT INCLUDED IN THE KIT
1.5mm Allen Wrench
2mm Allen Wrench
2.5mm Allen Wrench Cutter Curved Scissors
Craft Knife
Needle Nosed Pliers
Precision Caliper
Equipment Needed
.....x2
23 ASSEMBLY OF THE FRONT GEAR CASE ONTO CHASSIS 34056
94019 3x10mm Flat Head Hex Screw
.....x2
94026 4x12mm Flat Head Hex Screw
.....x2
94023 3x25mm Flat Head Hex Screw
.....x2
3x10mm
4x12mm
3x25mm
24 ASSEMBLY OF THE CENTER DIFF. ONTO CHASSIS *Insert the drive shaft into the cap joint before assembly center diff. onto chassis.
34050 94027 4x16mm Flat Head Hex Screw .....x4
4x16mm 4x16mm
25 ASSEMBLY OF THE REAR GEAR CASE ONTO CHASSIS
94027 4x16mm Flat Head Hex Screw
*Insert the drive shaft into the cap joint before assembly rear gear box onto chassis.
.....x4
34050
94023 3x25mm Flat Head Hex Screw
.....x2
4x16mm
3x25mm 4x16mm
26 ASSEMBLY OF THE STONE GUARD ONTO CHASSIS 34080
94019 3x10mm Flat Head Hex Screw
.....x6
3x10mm
3x10mm
3x10mm
27 ASSEMBLY OF VELCRO STRAP INTO BATTERY CASE Step 2 Step 1
30662
30663
28 ASSEMBLY OF THE ELECTRIC SPEED CONTRTOL
Double side tape (Not Included)
Electronic Speed Control (not included)
29 ASSEMBLY OF THE BATTERY TRAY BRIDGE ONTO BATTERY CASE 3x8mm
3x10mm
30662
94002 3x8mm Hex Screw
.....x2
94003 3x10mm Hex Screw
.....x2
30662
30662
30 ASSEMBLY OF THE ELECTRIC SPEED CONTROL WIRE INTO RADIO CASE
Step 1
Step 2
31 ASSEMBLY OF THE STEERING SERVO ONTO RADIO CASE 3x10mm
3x8x0.8mm
3x10mm 3x8x0.8mm Steering Servo (Not Included)
94003 3x10mm Hex Screw
.....x4
30662 94040 3x8x0.8mm Washer
.....x4
32 ASSEMBLY OF THE SERVO WIRE INTO RADIO CASE
33 ASSEMBLY OF THE BATTERY CASE ONTO CHASSIS
94019 3x10mm Flat Head Hex Screw
.....x3
94026 4x12mm Flat Head Hex Screw
.....x1
94053 5x10mm Flat Head Hex Screw
.....x2
5x10mm
3x10mm 3x10mm
34 ASSEMBLY OF THE RADIO CASE ONTO CHASSIS
3x10mm 3x10mm 94019 3x10mm Flat Head Hex Screw
.....x4
35 ASSEMBLY OF THE RECEIVER INTO RADIO CASE 30560 Antenna Wire 3x8mm 40642
Please carefully read the Receiver Instruction Manuals before installation.
37410 30662
*Plug in your speed controller wire to CH2 and steering servo wire to CH1 of your receiver.
30662
Do not cut or shorten antenna wire.
Step detail Receiver(not included)
94002 3x8mm Hex Screw
Use a screwdriver to straighten the antenna wire so it is easier to insert into antenna tube.
.....x2
36 ASSEMBLY OF THE STEERING ROD ONTO STEERING SERVO Sanwa/Airtronics JR
S
J
SAVOX Futaba
F
HiTech
30661 30411
H
Use the screw provided with your servo.
Choose the right servo horn adapter for your servo. 30401 3x12mm 30401
38280(3x36mm)
30661
3x12mm
30411
94004 3x12mm Hex Screw
.....x2
Approx. 19mm 30411 6mm Ball Socket .....x2
13
37 MOTOR INSTALL
Electric Motor (Not Included)
30670-(12T) 30664-(13T) 30665-(14T) 30666-(15T) 30667-(16T) 30668-(17T)
Step detail
*Approx. 20mm
4x4mm
94034 4x4mm Set Screw
.....x1
38 MOTOR INSTALL
94038 3x12mm Cap Screw
Do Not Over Tighten
.....x2
3x12mm
3x8x0.8mm 94040 3x8x0.8mm Washer
Ensure Free Movement
.....x2
39 ADJUST MOTOR AND SPUR GEAR MAINTENANCE
Tighten the 3x12mm screw temporary.
EXTREMELY IMPORTANT
Notebook paper Tighten
Insert a piece of notebook paper between spur gear and pinion gear to make correct gear mesh.
PUSH
Tighten
Adjust the motor position to get proper gear mesh. To get a perfect gear mesh , place a piece of notebook paper between the gears and tighten the motor mount screws. The spur gear will strip if the gear mesh is wrong.
14
40 BATTERY INSTALL
If use hard case battery , make a hole as picture shown.
15mm
8mm Follow the manual instruction provided by ESC manufacturer to install the wire.
41 ASSEMBLY OF THE REAR SHOCKS * Make 2 for Shocks for rear.
Step 1 2.5mm Nylon Nut .....x2
40643 Shock Plastic Ball End *Fit the o-ringinto groove before (Short) assembly.
30403
40636
Step 2 1. Pull down piston and 3. Pull down piston, pour oil into shock attach pressure top cylinder. and shock oil 2.To remove air bubbles overflow with tissue by slowly moving paper. piston up and down.
40634
40635
40090 3.5mm O-Ring .....x4
40637 40090 40090 1mm Washer .....x2 40090
40090 2mm
*Fill the shocks with oil approx 90%.
40736
CORRECT SHOCK ASSEMBLY Carefully screw the shock shaft into the bottom of the plastic ball and until the distance between the ballend and the shock body is 15mm for the front. N.B. Do not over tighten as the plastic will strip.
40643
40090 1mm
2.6x6mm Washer 40638
.....x2 40737
30403 6mm Ball End .....x2
15mm
40640 40090 2mm Washer
40633
2.6x6mm Washer 2.5mm
0
2.6x6mm Washer .....x4
10
30
20
40
42 ASSEMBLY OF THE REAR SHOCKS * Make 2 for Shocks for front. Step 1 2.5mm Nylon Nut .....x2
40643 Shock Plastic Ball End *Fit the o-ringinto groove before (Short) assembly.
30403
40636
Step 2 1. Pull down piston and 3. Pull down piston, pour oil into shock attach pressure top cylinder. and shock oil 2.To remove air bubbles overflow with tissue by slowly moving paper. piston up and down.
40634
40635
40090 3.5mm O-Ring .....x4
40637 40090 40090 1mm Washer
40090 2mm 40054
.....x2 40090
*Fill the shocks with oil approx 90%.
CORRECT SHOCK ASSEMBLY Carefully screw the shock shaft into the bottom of the plastic ball and until the distance between the ballend and the shock body is 32mm for the front. N.B. Do not over tighten as the plastic will strip.
40643
40090 1mm 2.6x6mm Washer
.....x2
40638 40632
30403 6mm Ball End .....x2
2.6x6mm Washer .....x4
32mm
40640
40090 2mm Washer
40633
2.6x6mm Washer 2.5mm
0
10
20
30
40
43 ASSEMBLY OF THE FRONT AND REAR SHOCK SPRING
* Assemble 2 Sets for Front
* Assemble 2 Sets for Rear
30274
30275 40643
40643
44 ASSEMBLY OF THE FRONT SHOCK ABSORBER 3x25mm
94041 3mm Nylon Nut
.....x2
94007 3x20mm Hex Screw
.....x2
40531 94040 3x8mm
90018 3x25mm Cap Screw
3mm .....x2
Do Not Over Tighten
3x20mm
Assembly for both right and left side.
45 ASSEMBLY OF THE REAR SHOCK ABSORBER
94041 3mm Nylon Nut
.....x2
94007 3x20mm Hex Screw
.....x2
40531 3x8mm
90018 3x25mm Cap Screw
3x25mm
3mm .....x2
Do Not Over Tighten
3x20mm Assembly for both right and left side.
16
46 ASSEMBLY OF THE FRONT BUMPER 33011
Choose the correct body post pin hole for your body.
33011
Step 1
Step 2 31159
2mm 33011 M2 Nut .....x2
2x18mm 34091
2x18mm Screw .....x2
94010 4x12mm Hex Screw
33011 .....x2 34090
94011 4x16mm Hex Screw
.....x4
4x12mm 4x16mm
47 ASSEMBLY OF THE TIRES AND WHEELS
86050 *Pull back the tire bead slightly and spot glue in four spots as shown. When dry, glue the rest of the wheel between the spots. Repeat the procedure on the other side of the wheel until fully glued.
Contact Adhesive
10239 IN ST GL ANT UE
Contact Adhesive
86026 86059 Inner Sponge (WidE) 86059 Inner Sponge (Narrow)
48 ASSEMBLY OF THE WHEELS ONTO THE FRONT KNUCKLE AND REAR HUB
Assembly for both right and left side.
40550
40550 Wheel Nut .....x4
40550
Tire and wheel assembly.
40550
40550
OPERATING YOUR MODEL SAFELY Before Running Your radio control model can move at high speed and therefore can cause injury to people or damage property. It is your responsibility to operate your model safely.
Engine Start-Up
While Running
Cautions for Safety
For engine use, refer to the manual included with the engine.
Check that the model turns in proportion to the amount you move the steering control of the transmitter.
Do not run your model through water. This may cause rust or electrical problems.
To prime the engine with fuel, press down the primer button.
Check that the speed of the model changes in proportion to the amount you move the speed control of the transmitter.
For radio equipment, refer to the manual included with the radio.
Check that all screws and nuts arc tight.
If the model begins to operate by itself, there is someone else on your frequency. Do not try to operate your model under these conditions for it may go out of control.
If model does not operate correctly stop it and find the cause.
Check the batteries. Attach one clip to the glow plug's end and the other clip to one of the cylinder cooling fins.
After Running
By pushing with your fingers the air cleaner, interrupt the engine
Fill in the fuel.
After each run, the model is hot. Beware of getting burned.
Quickly. pull the starter rope (to start the engine).
Fully extend transmitter antenna.
Switch off receiver.
Keep hands and tools away from moving parts. Adjust by screwing the needle little by little.
Switch off transmitter.
Switch on transmitter.
OFF OFF
ON
ON Remove the clips from the engine. Proper maintenance extends the life of the model.
Switch on receiver.
Use genuine parts.
Never throw burning, gleaming or smouldering things into fuel cans even if these happen to be empty. This is very dangerous to life! I!
SETTING GUIDE FRONT TOE-IN AND TOE-OUT SETTING Use a 5mm allen wrench to adjust toe-in for front . (Front) Adjust the length of the front steering rod to change the toe angle. NEUTRAL POSITION
Making the steering rod longer will make the front tires become toe-in. Response will be slower and will over steer.
TOE-IN TOE-OUT
TOE-OUT
Making the steering rod shorter will make the front tires become toe-out. Response will be quicker and will under steer. We recommended adjusting the front toe-out to 1.5 degrees.
4'5'5.5'7mm Allen Wrench
Steering Rod
Use rear tor-in adjuster.
Rear Toe-In
Rear Toe-In
1 Degree
1.5 Degree
Set triangle marks in the direction shown in Fig.(1)
Fig.1
FRONT AND REAR CAMBER ANGLE SETTING c rn w x h m .5 2 e s U ¡¯ @ ¡p o d tu b m lra je s @ ¡ft in .ro
Note: Place the model car on a flat surface. Raise the chassis to it's maximum clearance before the wheels leave the ground. Adjust the length of the front and rear upper arms so that the wheels are right angles to the ground.
(REAR)
(FRONT)
+ Positive
-
-
+
+ Positive
Negative
-
-
+
Negative Turnbuckle
The front camber adjustment can be made by moving the 14mm steering ball at the front upper arms on knuckles, clockwise or anticlockwise. We suggest using 1.5 degress of negative camber for the front.
Adjust the length of the turnbuckle on the rear upper arms can be change the rear camber. We suggest using 2 degress of negative camber for the rear.
FRONT AND REAR SHOCK ANGLE SETTING Firm
Soft
(FRONT)
Soft
(REAR)
123
Firm
Soft
1 2
Firm
Firm front suspension, less steering. Soft front suspension, more steering.
1 2 3
Soft
12
Firm
Firm front suspension, less steering. Soft front suspension, more steering.
3 4 3 0 6 U L T R A G T P 2 e P A R T S L IS T O FN A 30010 30080 30082 30202 30262 30272 30273 30274 30275 30110 30120 30121 30130 30160 30201 30341 30351 30361 30380 30401 30403 30411 30482 30620 30630 30649 30653 30654 30656 30658 30659 30661 30662 30663 30665 30673 30674 30675 30751 30761 30769 30773 30776 30777 30779 30779 30780 30901 30911 31159 31300 33010 33011 34014 34027 34050 34054 34055 34090 34091 34110 36052 36053 36055 36081 36082 36100 36170 36171 36640
D ESC R IPT IO N S M AIN G EAR C ASE, Q U IC K C H AN G E JO IN T C AP, 6m m , 2 PC S. JO IN T C APS, 6m m , 2 PC S. C EN T ER , D IFF AD APT ER SH O C K T O W ER FR O N T G T P 2 H .C . FR O N T PLAT E JO IN T H .C . G T P 2 ST ABILIZER BAR 2.5m m G T P 2 SPR IN G FR O N T G T P 2 1.8x6T SPR IN G R EAR G T P 2 1.8x10T G EAR , SPU R (N YLO N ) U LT R A G EAR , BEVEL 44T , ST O C K M ISC BEVEL M O U N T IN G H AR D W AR E G EAR , BEVEL PIN IO N FR O N T PLAT E, AR M PIN H O LD ER S C EN T ER , D IFF M O U N T , N EW T YPE BALL EN D W IT H C O LLAR , 6m m R EAR AR M H O LD ER 3PC S SER VO SAVER SH AFT SER VO SAVER PO ST S, 2 PC S. ST EER IN G EN D S, PLAST IC 6 PC S. 6m m BALL, ST EEL (N O C O LLAR ) 6m m BALLS w/C O LLAR ,ST EER IN G 6P SPAC ER S, R AISE EN G IN E M O U N T BEAR IN G KIT , 7x19m m , 6 PC S. BEAR IN G KIT , 6x13m m 12PC S. SH O C K T O W ER R EAR LX 1 H .C . C EN T ER T O P PLAT E LX 1 H .C . H O LD ER , U PPER AR M ALU . LX 1 H .C W H EEL H U B, LX 1 H .C . SER VO SAVER C O N N EC T O R H .C . LX 1 FR O N T T O P PLAT E H .C . LX 1 SER VO H O R N H EAVY D U T Y BLAC K BAT T ER Y C ASE,R X BO X LX -1e BAT T ER Y VELC R O ST R APS LX -1e PIN IO N 14T 5M M SH AFT AR M H O LD ER FR H .C . LX -1 SER VO SAVER PLAST IC SET LX -1 C N C M O T O R M O U N T LX -1e C ASE, D IFF (K), FR O N T or R EAR C ASE, D IFF C ASE (K), C EN T ER D IFF G EAR ,SILVER BEVEL,SET 4m m C R O SS PIN AX LES, 4m m ST EEL W ASH ER , 4x10x0.2m m 4PC S. SEAL, O -R IN G (LAR G E) D IFF C ASE M ISC . PAR T S, O LD D IFF & (k) M ISC . PAR T S, O LD D IFF & (k) PIN S, 2X 12.8m m FO R D IF 2PC S C AP JO IN T W /SH AFT F /R D IFF C AP JO IN T W /SH AFT , BR AKE BO D Y C LIPS, C H R O M E AN T IR O LL BAR G T P FR O N T & R EAR M O U N T IN G KIT , G T P M O U N T IN G KIT , SED AN (G T P) BR AC E, FR O N T C H ASSIC ,U LT R AC O M P AN T I-R O LL BAR KIT , U .C O M P,LX 1 C EN T ER BO N ES, U LT R A G T , 2PC S SH AFT , R EAR D O G BO N E 93m m PR . PIN S, LO W ER R EAR AR M S 3x42.6m m BU M PER , U LT R A SED AN G T P/R ALLY FO AM BU M PER , G T P/R ALLY BEAR IN G , 5x10, 2 PC S C VA JO IN T S,F/R W II&M BX 95 8m m PR BEAR IN G , 8x16m m , PAIR PIN , 2.5x17m m , H EX H U BS, 4PC S R EAR U P-R IG H T (8m m BEAR IN G ) PR R EAR AX LES, 8m m PAIR C EN T ER D O G BO N ES,SET 86 & 90m m R EAR AR M PIN S, 3m m 4PC S AR M PIN 4m m FR O N T IN SID E LX 1 AR M SH AFT , 4m m , SH O R T , 2PC S
R ET AIL 14.95 9.95 9.95 1.95 7.95 7.95 3.95 5.95 5.95 7.95 10.95 1.95 14.95 4.95 13.95 3.95 3.95 5.95 4.95 2.95 4.95 4.95 4.95 29.95 59.95 11.95 6.95 7.95 11.95 6.95 6.95 4.95 19.95 9.95 12.95 12.95 7.95 29.95 9.95 9.95 14.95 3.95 1.95 3.95 9.95 9.95 3.95 11.95 11.95 4.95 24.95 9.95 12.95 3.95 3.95 15.95 15.95 15.95 12.95 15.95 6.95 49.95 12.95 3.95 12.95 10.95 16.95 7.95 5.95 9.95
O FN A 36680 36690 36700 36741 36742 36743 36790 36861 36890 36900 36901 36903 36904 36905 37410 38280 40028 40029 40038 40039 40055 40060 40065 40090 40199 40531 40550 40632 40633 40634 40636 40637 40638 40640 40642 40643 40736 40737 41033 86023 86024 86025 86026 86027 86028 86029 86030 86050 86051 86052 86053 86059
D ESC R IPT IO N ST IFFEN ER SU PPO R T ,7m m F&R 3PC . U PPER BALL EN D , 7m m 6PC S ST EER IN G BALL EN D , 7m m , 8PC S. SPR IN G , SER VO SAVER N EW H AR D BU SH IN G , SER VO SAVER 6m m E-C LIP, SER VO SAVER 4x46M M T U R N BU C KLES,4PC S. 5x40m m T U R N BU C KLES, 2 PC S BLK FR O N T LO W ER AR M S (m bx4) PAIR FR O N T U PPER AR M S (m bx4) PAIR KN U C KLE, PIVO T BALL (m bx4) 2PC PIVO T BALLS, ST EEL (m bx4) 4PC S 14m m ALU M . N U T (m bx4) 4 PC S W ASH ER PLAST IC , 14m m N U T S BO D Y C LIPS, 10 PC S. SM ALL JL10 3x36m m T U R N BU C KLE D O G BO N ES, 93M M PAIR LX 1 BALL EN D S, PLAST IC , AN T I-R O LL BALLS, 7M M 4PC S. C O N E, ALU M . 3M M , 4PC S. SH AFT S,3.5m R EAR SH O C KS, 2PC S N YLO K N U T , 2.5, PIST O N N U T , 4 BALL EN D S, PLAST IC , R EAR U PPER SEALS,SH O C K R EBU ILD , 9.5 X -1 ST EER IN G BALL EN D ,PLAST IC , 6m m SH O C K BALL PO ST /O N E-PIEC E/T O P W H EEL N U T 5m m SH O C K BO D Y FR O N T 13m m SH O C K C AP, 13m m SH O C K SPR IN G S AD JUST ER , 13m m O -R IN G 15x1m m FELT F O R R ED D U ST , 13m m SH O C K SH O C K PIST O N 13m m SH O C K, PR ESSU R E T O P, O R AN G E AN T EN N A , FIX IN G N U T PLAST IC SH O C K PAR T S,13m m SH O C K SH O C K SH AFT D M -1 SH O C K BO D Y, 13m m D M -1 ST O N E G U AR D S X 2T 17m m W H EELS, V SPO KE, BLAC K PK 17m m W H EELS, V SPO KE, BLU E PK 17m m W H EELS, V SPO KE, LIM E PK 17m m W H EELS, V SPO KE, W H IT E PK 17m m W H EELS, V SPO KE,O R AN G E PK 17m m W H EELS, V SPO KE, G R AY PAK 17m m W H EELS, V SPO KE, YEL PAC K 17m m W H EELS, V SPO KE,C H R O M E PK 1:8 T IR E, SLIC K w/o BELT , PAIR 1:8 T IR E, SLIC K with BELT ,PAIR 1:8 T IR E,T R EAD ED w/o BELT , PR . 1:8 T IR E,T R EAD ED with BELT ,PR . FO AM ST R IPS, IN SER T S, LO W -PR O
30664 30666 30667 30668 30774 31010 31138 31040 31141 31144 31295 33992 33994 33995 33996 33997 41116
PIN IO N 13T 5M M SH AFT PIN IO N 15T 5M M SH AFT PIN IO N 16T 5M M SH AFT PIN IO N 17T 5M M SH AFT C R O SS PIN AX LES, 4m m ALU M 6PC S G EAR , BEVEL 44T , H D ST EEL BO D Y, D T M M -T YPE C LEAR G EAR , SPU R , 51T ST EEL BO D Y, M -T YPE W IT H D EC ALS BO D Y, V-G T P W IT H D EC ALS R EAR PIVO T BALL KIT ,U LT R A G T P PC R FR ST IFFN ER BR AC E U LT R A PC R U PPER FR AR M U LT PC R ST EER IN G LIN K PLAT E U LT R A PC R U PPER PLAT E, FR O N T D IFF U L PC R C EN T ER D IFF. T O P PLAT E U LT C N C ALU M . BALLS SET H AR D C O AT ED
R ET AIL 8.95 6.95 6.95 3.95 1.95 2.95 10.95 6.95 13.95 11.95 13.95 7.95 9.95 5.95 3.95 5.95 19.95 3.95 9.95 3.95 7.95 4.95 4.95 7.95 7.95 9.95 4.95 24.95 18.95 9.95 3.95 1.95 7.95 5.95 2.95 9.95 7.95 24.95 15.95 19.95 19.95 19.95 19.95 19.95 19.95 19.95 23.95 19.95 35.95 19.95 35.95 9.95
LX-1e O PTIO N PARTS 12.95 12.95 12.95 12.95 9.95 28.95 64.95 29.95 64.95 59.95 54.95 24.95 13.95 14.95 15.95 15.95 24.95
BLANK
OWNER’S REGISTRATION CARD OFNA Racing congratulates you on your purchase of our fine OFNA Product. With proper maintenance and handling this kit will provide many hours of enjoyment. The registration card should be filled out and mailed to OFNA Racing within 10 days of purchase date. In the event that the kit is incomplete or component parts are broken due to error in manufacturer, contact your dealer from which you purchased the kit for replacement part or call OFNA at (949) 586-2910 for your nearest dealer location. Other items such as radio and engine other covered by individual warranties. IMPORTANT! Please print or type, filling in the information listed below and mail immediately
MAIL TO: OFNA RACING 7 VANDERBILT IRVINE, CA. 92618 TEL: (949) 586-2910
Write in Your Model Name and Part Number
REGISTRATION CARD
RACER’S NAME
TEL:(
)
ADDRESS
CITY
STATE
DEALER’S NAME
ZIP
TEL: (
ADDRESS
CITY
OFNA 7 Vanderbilt Irvine, Ca. 92618
STATE
ZIP
)
