Transcript
ChapterⅠ 1.1 1.2 ChapterⅡ 2.1 2.2 2.3 2.4
Ins tal lation---- ---------------------------------------------------------1 Safety Instructio n------------------------------------------------------- 1 Instal lation Instruction--------------------------------------------------- 2 Maintenance--- -------------------------------------------------------- 3 Foreword--------------------------------------------------------------3 Troubleshooting-------------------------------------------------------- 3 Note---------- ------------------------------------------------------- -6 Attached drawing s------------------------------------------------------ -6 Electric diagram-------------------------------------------------------- 7
1.1 Safety Instruction After unpacki ng, the appliance should be checked to see if there is any damage to it. The dishwasher is intended to wash dishes and plates by adult s. When using the dishwasher , some basic principals should be followed: 1) Extended power cord and adaptor shoul d not be used. 2) The power cord should not be too long or knotted. 3) Swi tch off the power before maki ng any repair of the dishw asher. Children should be kept away from the detergent and the opened dishwasher. Then dishwasher should not be install ed in an unsheltered pl ac e or exposed to the rain or other natural environment. Never touch the heating el ement during or immediately after u se. The dishwasher shoul d not be lean on or sit on when i t is open , otherwi se it will be overturned. If the dishwasher malfunctions, turn off the water inl et and cut off the power before you read the instruction of C hapterⅡ. If the problems cannot be solved by y ourself, please contact the professi onal technici ans. The dishwasher could not be repai red by unprofessional personnel wi th non-original spare parts. It is recommended that i f the di shwasher wi ll not be used for a long time, it should be cut off the water inlet, remove the plug and keep the door of dishwasher a j ar.
1
1.2 Installat ion Instruction Unpacking 1) Remov ing the packing accessories, please pay attention that the plas tic bag should be out of the reach of c hildren. 2) Open th e door of the dishwasher to check the baskets are placed in the proper pl ace (manufact ures may fix the baskets by some simple ways for the sake of safety). Locate the dishwasher 1) The dis hwasher should be kept away from heating resources and not be exposed to the sun to prevent its coating from fading or fal ling off. 2) The back of the dishwasher shoul d rest against the wall behind it and the sides, along the adj acent c abinets or wall. The water supply and drain hose of the dishwa sher coul d be positioned to the ri ght o f the left to facili tate proper instal lation. 3) The dis hwasher should be buil t in the cabi net and fixed it on the cabi net by two screw.
Installat ion steps
1) Install the aesthetic pannel on the outer door of the dishwasher. 2) Adj ust the tension of door spring. 3)level the dishwahser and touch the cabi net by adjusting the four l eveli ng legs i ndividuall y. 4) Conne ct the inl et, and drain hoses, and power cord . 5) pushi ng the dishwasher into the cabinet. 6)fixing t he di shwasher into the cabinet by two countersunk head screw.
2
6
1
5
Aestheti c pan el
3
Install ation steps
When you want more particular content about installation, please t o see the installation manual w e edited. 2
2.1 Foreword
Be fore any repai r service, you should check: a) Whether the dishwasher i s properly installed according to the in stallation manual. b) Whether the damaged components have been repaired or not. c) Whether the charging hose and the drai n hose are properly inst alled. d) Whether the di shwasher is level or not. e) Whether there is salt in the water softener. f) Whether there is rinse agent in the dispenser.
The ci rcuit board is the centrum of the whole control system of the dishwasher. When dishwasher is w ashing though a i nformation comes to the circui t, then th e circuit deli vers various dictate to ev ery department of di shwasher to keep the dishwasher mo ving. the dishwasher move with a arranged program. If you know the program and structure o f the dishwasher, the bel ow table shoule be hel pful to establish a resolve to any problems occurred.
2.2 Troubleshooting Questions put forward by users The dishwasher do es not st art
By misusage of users
* Somet hing wrong with the socket * No water (t he water valve is closed) * Improper electrical connection * The door is not properly closed * Incorrect position of charging hose
The problems problem sofofthe t hedishwasher dishwasheritself it self
* Power cord * "ON/OFF" switch * Door switch * Wat er inlet valve * Pressure switch * Aqua-stop switch
Water fl oods in the dishwasher
** Air Airleakage leakageof of the thechamber chamber ** The Thehose hoseof ofpressure pressureswitch switch ** Pressure Pressureswitch switch ** Wat Watererinlet inletvalve valve
The dishwasher do es not heat
* Malf unction of heating element * The circuit is not properly contacted * Malf unction of t he thermocouple
No water comes into the dishwasher * Wat er supply is cut off * The f ilter of the water inlet valve is clogged.
* Connection to the inlet valve is broken or damaged. * Electrical connection is cut off. * Pressure switch * Aqua-stop switch * The softener is blocked.
3
* The f ilter is clogged. * Unqualified d etergent or the dosage in the container is not correct. * No salt in the softener * No rinse agent * Incorrect loading of dishes * Something wro ng wit h t he drain pipe in the home
* Flow and pressure of washing pump ** Flow and pressure of washing Detergent is not released frompump * Detergent is not released from dispenser dispenser * Heating elem ent is not working ** Heating elem ent is notbyworking The noz zle is blocked food *part Theicles noz zle is blocked by food part * Noicles water c oming into the *dishwasher No water c oming into the dishwasher * The dispe nser malfunctions ** The dispeinnser malfunctions someth g wrong wit h the pressure * Sth wrong with t hewater pressure switch sw itch re du ci ng press ure and the cha rging water is not enough
The dishwasher doe sn't wash properly
* Wrong loading position of t he dishes.
* Short circuit of startup capacit ance * Washing motor is blocked or burnt * Pressure switch * Malf unction of t he circuit board
The dishes are wet
* The customer chose t he program without drying performance
*Therm ocouple doesn't work properly * Heating ele m ent has malfunct ioned * Somet hing is wrong with t he circuit board
The dishes are no t completely dried
* Incorrect loading of t he dishes * Earlier opening of the door * No rinse agent or the dosage is not enough * Incorrect program selection
* The passage of the air breather is blocked * The drain pump does not drain out water * Detergent is not released from the dispenser
Too much nois e
* I ncorrect loading of dishes
Elect rical charges from dis hwas her
* The electrical wire in the house is not earthed.
Water leakage an d f lo od of the dishwasher
* Too much detergent * Using the detergent not int ended for use w it h dishwashers.
The dishes are not clean enough after washing
4
* Nois e from washin g pump * Nois e from drain pum p * Nois e from water inlet valve *Nois e from air brea ther
* Connection of the t erm inal box * Grounding of t he heat ing element * Circuit and its components
* Pressure switch * Door gasket * Wat er leakage of pipes , gasket s and bolts * Drain hose * Washing pum p * Soft ener valve * Soft ener * Air breather
Unu suel smell in the dishwas her
* Food particles on the tub bot tom * Food particles on the heating element * Plastic dishes used in t he dishwasher
* The w at er t emperature is too high when drying (overheat ing) * Therm ocouple doesn't work prope rly
Long time for a washing cycle
* Inlet pressure is too low * Incorrect locat ion of charging and drain hoses or t hey are bent * The f ilter of inlet valve is blocked
* The drain hose is crimped or bent * Malf unction of t he drain pum p * Inf ill of t he inlet valve is blocked * Clog of the soft ener * Malf unction of t he therm ocouple
The det ergent co uld not be released from the dispenser
* Bad qualit y of the det ergent * The detergent is damped int o blocks * Wrong location of t he dishes
* The plug of detergent container could not be opened. * No act ion of the solenoid valve of elect ric feeding dispenser. * Malf uncti on of t he elect ric circuit * Malf uncti on of t he therm ocouple
Dishwasher stops when cyclin g
* The door is not complet ely shut * The f ilter is blocked * Too much detergent
* Electric ci rcuit * Door swit ch * Pressure switch * The circui t board * Power sw itch
Dishes are dama ged or glassw are is broken
* The dishes are not suitable for washing in t he dishwasher * The dishes are overturned * The w ashing temperature is not suitable f or glassware
* Basket is dam aged * Malf uncti on of t he therm ocouple
The dishwasher does not drai n
* Block of drain hose
* Malf uncti on of drain pump * Improper connect ion of electric circuit * Malf uncti on of t he therm ocouple
Lime deposit s form on t he dishes
* Too much detergent
* Reduce the dosage
The dishes look greasy and a blue f ilm forms on them s omet im es
* Too much rinse agent
* Reduce the dosage
Dirty spots o n t he surf ace of the dishwasher
* The detergent sticks to t he damp surf ace
* Use the deter gent according t o t he user's manual * The detergen t should not be spilled on the surface of the dishwasher
Strange color o f the surface of the washed dishes
* The salt is not int ended to use in the dishwasher.
* The influe nce of salt on the resin
5
2.3 Notes
E8.If the distributary valve have worked for 150 seconds, and could not reach right position during wash cycle,after the cycle is finished, the dishwasher will shut off all loads, the alarm buzzer will ring for 30 seconds and the window will display "E8" at rate of 1Hz in 30 seconds, and then display "E8" , drain water for 2 minutes meanwhile
Control Panel Auto 3 in1
2 3 4
1 1 2 3
Display window: Program remaining time, delay time, running indicator, Program indicator, Salt and rinse aid indicator, Error codes, etc. Program button: To select one of the six programs. .
5
Delayed Start Button: To preset the wash timer and delay the starting time up to 24 hours. Every press of this button increases the time by one hour. （for example: one press for an hour, two for two hours... ... ） 5 Power switch: To turn on/off the power supply.
4
3in1 and half load function button: To select and show 3in1 and Half load functions. (Half load function means that the lower spray arm does not run, so you should load the upper basket only ).
Error Codes When some malfunctions come on, the appliance will display error codes to warn you:
Codes
Meanings
Possible Causes
E1
Longer inlet time.
Tap is not opened, or water intake is restricted,or water pressure is too low.
E4
Overfilled.
Too much inlet water.
