Transcript
LN10RDT / LN10RDL-20W
®
NXT
Downlight Trim Round 1" Regress
1" Regress 21⁄2” Ø
Plan View
LUMINAIRE INFORMATION LIGHT ENGINE DELIVERED PERFORMANCE 20 Watts NanoLED NXT DOWNLIGHT
80+ CRI 49 1250 1000
Lumens per Watt Source Lumens Delivered Lumens
LN10RDT
315⁄16” Ø
90+ HIGH CRI 40 1025 825
High power white LEDs tightly binned for fixture-to-fixture color consistency within a 2-Step MacAdam Ellipse. MATERIALS: Trim: Precision die cast body with durable UV-stabilized powder coating. Reflector: Interchangeable tooless reflector system allows for flexibility while maintaining design consistency. Available in 25° and 50° distribution. Trim Lens: Solite Baffle Options: High temperature nylon. BM - Black Matte Baffle WM - White Matte Baffle BV - Black Vertical Groove Baffle WV - White Vertical Groove Baffle BA - Black Alzak MA - Matte Alzak
LN10RDL (Trimless) NOTES: • Maximum ceiling thickness up to 11/2" See housing matrix on back for exceptions. • Housing included with trim. • Trimless for drywall installation only • Trimless not available in acoustical ceilings. • Fixture should be installed in applications where ambient temperatures do not exceed 40°C during normal operation. • 5 year warranty • Interior use only.
RATED LIFE: Based on IESNA LM80-2008 50,000 hours at 70% lumen maintenance (L70). COLOR TEMPERATURE Standard CRI 2700K - 82+ CRI +/- 50K 3020K - 82+ CRI +/- 50K 3450K - 80+ CRI +/- 60K
High CRI 2700K - 90+ CRI 3020K - 90+ CRI
HEATSINK: Proprietary high performance aluminum heatsink for maximum LED life.
DRIVER: Field Replaceable DOWNLIGHT TRIM FEATURES Solid state electronic. Constant current. High power High Performance factor. Specify 120V or 277V. Driver complies with Heat Sink IEEE C62.41 surge protection. DIMMING: (optional) Multiple dimming drivers available. See compatibility chart attached.
Interchangeable Reflector
ACCESSORY HOLDER: "C" size accessory holder. Maxium 2 lenses. Die Cast Body
CEILING CUT OUT: 31/2" Ø
Trim Mounting Clips
LISTINGS: Dry/Damp IBEW union made.
HOW TO SPECIFY Trim
–
Baffle Options
– BM - Black Matte (Trim) Baffle LN10RDT (Trimless) WM - White Matte Baffle LN10RDL BV - Black Vertical Groove Baffle WV - White Vertical Groove Baffle MA - Matte Alzak BA - Black Alzak
–
Light – Engine
–
– MTG114 (14W LED) MTG120 (20W LED)
Color Temperature
–
Reflector
– Standard CRI 80+ 27KS - 2700K-82 CRI 30KS - 3020K-82 CRI 35KS - 3450K-80 CRI High CRI 90+ 27KH - 2700K-90 CRI 30KH - 3020K-90 CRI
– Trim Finish – Housing – Voltage – –
–
10 - White LRNT425 25° Distribution 21 - Black 28 - Metalized LRNT450 Grey 50° Distribution RAL - Special Color
– LSP55 LNC61 LNC63 LNC65 LIC1 LIC3 LIC5 LSH43
– 120V 277V
HOUSING DETAILS next page
BOFC - Borocilate Frosted LLFC - Linear Spread Frosted Low Iron SOFC - Solite Frosted PRFC- Prismatic Frosted HEXC- 1/8" Hex Cell Louver ®
USAI
www.usailighting.com
[email protected]
1126 River Road New Windsor, NY 12553
T 845–565–8500 F 845–561–1130
Accessories
CB27 - 27" C-Channel CB52 - 52" C-Channel DIML2- 0-10V Low Voltage 15% Dimming Driver DIML3- Lutron Hi-Lume LED / ECO System Series "A" 2 Wire Control 1% Dimming Driver DIML4 - Lutron Hi-Lume LED / ECO System Series "A" 3 Wire Control 1% Dimming Driver EML - Emergency lighting battery pack w/ remote test switch. Above ceiling access required for service EML not for use with IC/Airtight Housing LENSES and LOUVER © 2012. USAI, LLC. All rights reserved. All designs protected by copyright. Revised 05/22/12
LSP55, LSH43 LNC61, LNC63, LNC65 LIC1, LIC3, LIC5
®
NXT
Housings for use with NanoLED Downlight Trims - Round HOUSING FEATURES
• Easy adjustment aperture plate that allows ceiling thickness adjustment from 7/8" to 11/2". See housing matrix for details. • Patent pending "Slide & Replace" easy driver replacement. • Quick connectors on all wire connections. • Universal housing style allows the ability to swap trim styles between Downlight, Adjustable and Wall Wash. See Plug-and-Play limitations on matrix below. • Fabricated of 20 ga. black powder coated steel with thru wire J-box, 2 in 2 out at min. 90°C, #12 AGW thru branch circuit wiring.
LISTINGS: Dry/Damp IBEW union made.
NOTES: • Maximum ceiling thickness 11/2". See matrix for ceiling thickness options. • Housing included with trim. • Trimless for drywall installation only • Trimless not available in acoustical ceilings. • Fixture should be installed in applications where ambient temperatures do not exceed 40°C during normal operation. • 5 year warranty
DRIVER: (Field Replaceable) Solid state electronic. Constant current. High power factor. Specify 120V or 277V. DIMMING: (optional) 3 wire dimming driver available. See compatibility chart attached. MOUNTING: Butterfly brackets and adjustable nailer bars with integral nails provided. Nailer bars are extendible from 14" to 24" centers.
HOUSING INFORMATION - See limitations below New Construction
New Construction
New Construction
IC / Airtight
LSP55 - DL only (Max. Ceiling Thickness - 11/2")
LSH43 - DL / WW (Max. Ceiling Thickness - 11/4")
LNC61 - DL / ADJ / WW (Max. Ceiling Thickness - 7/8")
LIC1 - DL / ADJ / WW (Max. Ceiling Thickness - 7/8")
LNC63 - DL / ADJ 30° / WW (Max. Ceiling Thickness - 11/4")
LIC3 - DL / ADJ 30° / WW (Max. Ceiling Thickness - 11/4")
LNC65 - DL / ADJ 20° (Max. Ceiling Thickness - 11/2")
LIC5 - DL / ADJ 20° (Max. Ceiling Thickness - 11/2")
43/4"
51/2"
41/2" 63/4"
77/16"
131/4"
12"
51/4" 131/4" 171/2"
163/8"
163/8"
175/8"
Order housings with trims on reverse side.
®
USAI
www.usailighting.com
[email protected]
1126 River Road New Windsor, NY 12553
T 845–565–8500 F 845–561–1130
© 2012. USAI, LLC. All rights reserved. All designs protected by copyright. Revised 05/22/12
®
DIMMING DRIVER COMPATIBILITY SELECTION GUIDE DIML2 & DIML3
NXT
DIMMING DRIVER WIRING SCHEMES:
DIML2 LED: 0-10V FL Dimming Driver Wiring (Dims down to 15%)
Compatible Crestron Dimming System NOTE: Consult dimmer manufacturer for detailed installation information.
NOTE: Consult dimmer manufacturer for detailed installation information. For use with 0-10V fluorescent type controls. Use only with approved vendor models: Lutron: DIVA DVTV-XX XX=Color Leviton: IP710-DLX Lightolier: V2000FAMU 0-10V Dimmer (By Others)
LED 0-10V VIOLET CCT GREY
VIOLET GREY
DIMMING DRIVER
RED BLACK
+
-
Creston Model
Compatible
CLS-EXP-DIMFLV DIN-4DIMFLV4 DIN-A08 GLX-DIMFLV8 GLXP-DIMFLV8
Y Y Y Y Y
Min # of Creston Measured Fixtures Min-Max % Light Output Required (1) Limits (2) (3) 1 0-100% 15-100% 1 0-100% 15-100% 1 0-100% 15-100% 1 0-100% 15-100% 1 0-100% 15-100%
GROUND WHITE BLACK
(1) Operating dimmers with less than minimum required fixtures may cause flicker. The Max number of fixtures is limited by dimmer rating unless otherwise noted. (2) % Level refers to the Crestron Control System Intensity. Operating the dimmer below the Min % level may cause flicker. Operating the dimmer above the Max % may show no additional brightness. (3) % Level of light output from fixture when connected directly to power source (4) Dimmer requires a direct connection to neutral unless otherwise noted.
BUILDING POWER WIRING NOTE GROUND WIRE
DIML3 LED: Lutron Hi-Lume A-Series 2 Wire Fwd Phase (with neutral) / LED Dimming Driver Wiring (Dims down to 1%) Compatible Lutron Dimmers / Test Results NOTE: Consult dimmer manufacturer for detailed installation information.
Product
Part Number
NovaT Maestro Wireless RadioRA 2 1000W RadioRA 2 Adaptive dimmer RadioRA 600W RadioRA 1000W HomeWorks QS 600W HomeWorks QS 1000W HomeWorks QS Adaptive dimmer HomeWorks QS WPM HomeWorks 600W dimmer HomeWorks 1000W dimmer HomeWorks WPM GRAFIK Eye QS GRAFIK Eye 3000 RPM-4U Module (LCP, HomeWorks, GRAFIK Systems, Quantum) RPM-4A Module (LCP, HomeWorks, GRAFIK Systems, Quantum) GP Panels (LCP, HomeWorks, GRAFIK Systems, Quantum) Stanza
Fixtures Measured Per Dimmer Light Output 120V Only* Range
NTLV-600-CPN0199 MRF2-6ND-120 RRD-10ND RRD-6NA RA-6ND RA-10ND HQRD-6ND HQRD-10ND HQRD-6NA HQRJ-WPM-6D-120
1–8 1–8 1 – 13 1–8 1–8 1 – 13 1–8 1 – 13 1–8 1 – 11 (per output) HRD-6ND 1–8 HWD-10ND, HRD-10ND 1–8 HWI-WPM-6D-120 1 – 10 (per output) QSGR-, QSGRJ1 – 10 (per output) GRX-3100, GRX-3500 1 – 10 (per output) HW-RPM-4U-120, 1 – 26 LP-RPM-4U-120 (per output) HW-RPM-4A-120, LP-RPM-4A-120
1–8 (per output)
100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1%
Compatible ETC Dimming Cabinets / Test Results Approved for use with: ETC Sensor + Cabinet with D20 dimming module Measured light output 100% - 1% ETC Unison DRd Cabinet with D20F dimming module NOTE: Additional dim configuration required for optimum performance. Measured light output 100% - 1%
100% - 1% 100% - 1% 100% - 1% 100% - 1%
Wire Diagram for 2-Wire Control
100% - 1% 100% - 1% 100% - 1%
Forward Phase with Neutral 2-Wire Dimmer (By Others)
LED BLACK
SWITCHED HOT
WHITE GREEN
NEU GND
VV+
BLACK RED
100% - 1% DRIVER (BACK SIDE OF MTG PLATE)
Various
1 – 27
100% - 1%
SZ-6ND
1–8
100% - 1%
* Fixtures per Dimmer value assumes a 40W fixture. Number of fixtures may be higher if wattage is less than 40W. NOTE: Contact Lutron tech support for deganging rules when using wallbox controls on the Hi-lume A-Series LED Driver.
®
USAI
www.usailighting.com
[email protected]
1126 River Road New Windsor, NY 12553
T 845–565–8500 F 845–561–1130
© 2012. USAI, LLC. All rights reserved. All designs protected by copyright. Revised 05/22/12
®
DIMMING DRIVER COMPATIBILITY SELECTION GUIDE DIML4
NXT
DIMMING DRIVER WIRING SCHEMES:
DIML4 LED: Lutron Hi-Lume A-Series LED Driver with Eco System Control / LED Dimming Driver Wiring (Dims down to 1%) Compatible Lutron Dimmers / Test Results NOTE: Consult dimmer manufacturer for detailed installation information.
Product
Part Number
1-59 1-29 1-59 1-29 1-29 1-29 1-29 1-29 1-22
1-61 1-46 1-61 1-46 1-46 1-46 1-46 -
100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1%
1-22 1-22
1-46 1-46
100% - 1% 100% - 1%
1-22 1-29 1-22 1-22 1-59 1-59
1-46 1-46 1-46 1-46 1-123 -
100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% – 1% 100% - 1% 100% - 1%
BLACK ORANGE WHITE GREEN
SWITCHED HOT DIMMED HOT VV+ NEU GND E2 E1
BLACK RED
DRIVER (BACK SIDE OF MTG PLATE)
ECO-SYS BUS CAP WIRES
Wire Diagram for ECO System Digital Control CAP LEAD
LED
ECO SYSTEM Control (By Others)
100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1%
BLACK ORANGE WHITE GREEN
SWITCHED HOT DIMMED HOT VV+ NEU GND E2 E1
BLACK RED
DRIVER (BACK SIDE OF MTG PLATE)
PURPLE
32 per module
LED FL Control (By Others)
PURPLE/GREY
64 per EcoSystem
Wire Diagram for 3-Wire FL Control (no Eco System Control)
PURPLE
NTF-10, NTF-103P, NTF-10-277 NTF-103P-277 NF-10 NF-103P, NF-10-277 NF-103P-277 VF-10 SF-10P, SF-103P SF-12P-277,SF-12P-277-3 DVF-103, DVSCF-103P DVF-103P-277,DVSCF-103P-277 AYF-103P AYF-103P-277 VTF-6AM MAF-6AM, MAF-6AM-277, MSCF6AM, MCSF-6AM-277 Maestro Wireless MRF2-F6AN-DV Spacer System SPSF-6A,SPSF-6A-277, SPSF6AM, SPSF-6AM-277 Lyneo LX LXF-103PL Lyneo LX LXF-103PL-277 Radio RA 2 RRD-F6AN-DV HomeWorks QS HQRD-F6AN-DV Interfaces (1) PHPM-3F -120, PHPM-3F-DV NGRX-FDBI-16A Energi Savr Node CS-1L-WM, CS-2L-WM, with EcoSystem CS-1LCM, CS-2L-CM Grafik Eye QS QS with EcoSystem with ECO System Quantum Quantum PowerPak dim RMJ-ECO32-DV-B module ECOSystem
Measured Light Output Range
PURPLE/GREY
NovaT NovaT NovaT Nova Nova Nova Vareo Skylark Skylark Diva Diva Ariadni Ariadni Vierti Maestro
Fixtures Per Dimmer 120V 277V
ECO-SYS BUS
(1) For use with 3 Wire controls or Commercial Systems, RA Systems or Home Systems applications. *Contact Lutron tech support for deganging rules when using wallbox controls on the Hi-lume A-Series LED Driver. **Fixtures per Dimmer value assumes a 40W fixture. Number of fixtures may be higher if wattage is less than 40W.
Compatible ETC Dimming Cabinets / Test Results Approved for use with: ETC Sensor+ Cabinet with D20 dimming module Measured light output 100% - 1% ETC Unison DRd Cabinet with D20F dimming module NOTE: Additional dim configuration required for optimum performance. Measured light output 100% - 1%
®
USAI
www.usailighting.com
[email protected]
1126 River Road New Windsor, NY 12553
T 845–565–8500 F 845–561–1130
© 2012. USAI, LLC. All rights reserved. All designs protected by copyright. Revised 05/22/12
®
ColorPrecise Pro LED Module ™
NXT
USAI Interchangeable LED Light Engine PERFORMANCE SUMMARY 14 Watts 20 Watts
®
NXT
PERFORMANCE Lumens per Watt Source Lumens
90+ 90+ 80+ HIGH 80+ HIGH CRI CRI CRI CRI 87 875
Drive Current
71 715
350 mA
71 59 1250 1025
Light Engine
500 mA
SPECIFICATIONS
PHYSICAL DIMENSIONS
PHYSICAL CHARACTERISTICS MODULE SOURCE TYPE: Field replaceable discrete LED light engine utilizing CREE LEDs. CONNECTION: Micro quick release connector with locking feature. PROTECTION: Bidirectional 1500W transient voltage suppression. CONSTRUCTION: Aluminum core board with integral thermal pad.
2-1/8" Ø
PHOTOMETRICS COLOR CONSISTENCY: High power white LED tightly binned for fixture-tofixture color consistency within a 2-Step MacAdam Ellipse.
Standard CRI
High CRI
2700K - 82+ CRI +/- 50K
2700K - 90+ CRI
3020K - 82+ CRI +/- 50K
3020K - 90+ CRI
3450K - 80+ CRI +/- 65K
−
4000K - 80+ CRI +/- 70K
−
5/16"
NOTE: LIGHT ENGINES ARE INCLUDED WITH ALL NanoLED NXT FIXTURES
COLOR RENDERING INDEX: >80 or >90. COLOR RENDERING INDEX CONSISTENCY: +3 / -0 pts. LIGHT ENGINE LIFE: Lumen maintenance L70/B50 50,000 hrs. DIMMING: Multiple dimming options available. See fixture spec sheets.
COLOR CONSISTENCY 2-STEP
SPECTRAL DISTRIBUTION
3000K
LIGHT ENGINE REPLACEMENT
1.2
Spectrum
1.0 0.8 0.6 0.4 0.2 0.0
USAI Lighting Coordinates
380
500 600 Wavelength (nm)
700
2-Step MacAdam Ellipse for Fixture- NanoLED 3000K Spectral Power to-Fixture Color Consistency Distribution
OTHER
WARRANTY
REGULATORY: UL recognized. RoHS compliant. MERCURY CONTENT: None. UV OR IR CONTENT: None
5 year warranty.
®
USAI
www.usailighting.com
[email protected]
1126 River Road New Windsor, NY 12553
800
Simple Light Engine Replacement
T 845–565–8500 F 845–561–1130
© 2012. USAI, LLC. All rights reserved. All designs protected by copyright.
USAI Lighting LED Performance Summary BeveLED2.0 16 Watts BeveLED 2.0 DOWNLIGHT Lumens per Watt Source Lumens Delivered Lumens (30°) BEAM OPTIONS 10° 30° 50°
90+ HIGH CRI 55 1165 900
80+ CRI 68 1425 1100
24 Watts 80+ CRI 64 1725 1525
COMPARED TO:
33 Watts
90+ HIGH CRI 53 1410 1250
80+ CRI 63 2400 2100
32W CFL 42W CFL
90+ HIGH CRI 52 1960 1720
82 CRI 39.3 2400 1404
90W PAR 38 HALOGEN SPOT
82 CRI 38.5 3200 1872
99 CRI 12.9 1310 1159
80°
COMPARED TO: 16 Watts BeveLED 2.0 ADJUSTABLE
80+ CRI Lumens per Watt 62 Source Lumens 1425 Delivered Lumens 1025 Center Beam Candle Power (10°) 14000
90+ HIGH CRI 51 1165 835 11500
24 Watts 80+ CRI 59 1725 1400 19800
33 Watts
90+ HIGH CRI 48 1410 1160 16000
80+ CRI 58 2400 1950 26970
90+ HIGH CRI 48 1960 1600 22900
20W CMH 20W CMH 90W PAR 38 PAR 20 PAR 30 HALOGEN SPOT 81 CRI 39 1000 850 13000
81 CRI 46 1200 1020 19000
99 CRI 12.9 1310 1159 20000
BEAM OPTIONS 10° 30°
16 Watts BeveLED 2.0 WALL WASH
90+ HIGH CRI 43 1165 700
80+ CRI 52 1425 850
Lumens per Watt Source Lumens Delivered Lumens
24 Watts 80+ CRI 49 1725 1125
90+ HIGH CRI 41 1410 1040
33 Watts 80+ CRI 49 2400 1635
90+ HIGH CRI 43 1960 1435
SPACING CRITERIA 1.27
NanoLEDNXT 20 Watts Downlight NanoLED NXT 20 Watts Lumens per Watt Source Lumens Delivered Lumens Center Beam Candle Power (10°)
80+ CRI 49 1250 1000
90+ HIGH CRI 40 1025 825
BEAM OPTIONS 25° 50°
Adjustable 80+ CRI 46 1250 952 8725
90+ HIGH CRI 38 1025 780 7000
Wall Wash 80+ CRI 35 1250 725
USAI
99 CRI 18.25 912 804 9056
BEAM OPTIONS SPACING CRITERIA 10° 25° 1.27
® www.usailighting.com
[email protected]
90+ HIGH CRI 29 1025 600
COMPARED TO MR16 50W MR16 SPOT
1126 River Road New Windsor, NY 12553
T 845–565–8500 F 845–561–1130
© 2012. USAI, LLC. All rights reserved. All designs protected by copyright. Patent pending. CA-027 03/2012
®
BeveLED2.0
10° Beam
®
80+ CRI 90+ CRI
NXT
2-STEP
3000K
10° Beam
USAI Lighting Coordinates
