Usb Pc Reader

Transcript

DORMA Installation Manual USB PC Reader USB PC Reader Contents Contents 1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1 Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1.2 Correct use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1.3 Safety instructions and warnings . . . . . . . . . . . . . 5 1.4 Functional principle . . . . . . . . . . . . . . . . . . . . . . . 6 1.5 Read procedure . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1.6 Components supplied . . . . . . . . . . . . . . . . . . . . . . . 6 2 Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.1 Connecting the USB PC Reader . . . . . . . . . . . . . . 7 3 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.1 Reader software . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.2 Reading in ID card data . . . . . . . . . . . . . . . . . . . . . 9 3.3 Other software . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.4 Operating mode . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.5 Indala-Trovan reader (PX15) . . . . . . . . . . . . . . . . . 11 3.6 Mifare DESfire reader (PX71) . . . . . . . . . . . . . . . . 11 3.7 LEGIC advant reader (PX51) . . . . . . . . . . . . . . . . 12 EG Declaration of Conformity . . . . . . . . . . . . . . . . . . . 13 4 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  USB PC Reader 1. General Information The information provided in these assembly instructions may be modified without prior notification. All previous versions cease to be valid with the publication of these instructions. The information in these assembly instructions has been compiled to the best of our knowledge and in good faith. DORMA Time + Access GmbH accepts no liability for the correctness and completeness of the details provided. In particular, DORMA Time + Access GmbH cannot accept liability for any consequential damage due to incorrect or incomplete information. DORMA Time + Access GmbH accepts no liability for the perfect functioning of the USB PC Reader in external, nonsystem environments. Despite every effort to prevent mistakes, they can never be completely avoided. Therefore, we would be grateful to receive notification of any errors or omissions. DORMA Time + Access GmbH accepts no liability for the information included in this document being free of protected third-party rights. DORMA Time + Access GmbH does not provide any licences to its own or to third party patents or other protected rights with this document. The recommendations for installation made in this manual are based on the assumption that prevailing basic conditions are favourable. It is not permissible to print, reproduce or pass this manual, or parts thereof, to third parties, other than for your own use, without the approval of DORMA Time + Access GmbH. All rights reserved. DORMA Time + Access GmbH Postfach 21 01 85 53156 Bonn http://www.dorma-time-access.de E-Mail [email protected] © Copyright 2009 by DORMA Time + Access GmbH Drawing no.: 1078G-B1 Status: 01/12 V1.20  USB PC Reader 1. General Information 1.1 Preface This installation manual is intended to enable you to connect and commission the USB PC Reader. 1.2 Correct use This device is intended exclusively for use in attendance recording and access control systems. Further details are described in chapter 1.4. Use for any other purpose than that described is not permitted. 1.3 Safety instructions and warnings This device has been constructed and tested in accordance with all currently applicable technical regulations. It left the factory in perfect condition in terms of safety and reliability. To maintain this condition and to ensure risk-free operation, the instructions and warnings given in this assembly guide must be observed by the user. • The device may only be used for the purpose intended by the manufacturer. Electromagnetic compatibility: • The unit is designed for use in residential, business and commercial areas and conforms to EN 300330-1- and 301489-6-1,-3. • The PCB can be damaged by static electricity discharge, so the relevant precautionary measures must be observed (grounding etc.). • These units may only be operated when mounted. • Before opening the unit, always switch off the power supply. • During assembly, please ensure that the requirements laid down in the relevant equipment safety standard for the unit are adhered to since violating them could affect the safety of the device. • If it must be assumed that safe operation is no longer possible, take the unit out of operation and secure it against accidental use. • Before switching on, ensure that the operating and control voltages connected do not exceed the permissible values, in accordance with the technical data. • This unit conforms to EN 60950-1 protection class III  1. General Information USB PC Reader 1.4 Functional principle The USB PC Reader is an ID card reader that transmits ID data read from the card to a PC application. All variants are based around a contactless reader. The USB PC Reader will read data from an ID card that is within range of the antenna. This requires that the ID card is held over the printed antenna symbol on the reader housing at a minimum distance of 4 cm* for a period of approximately one second. The data read from the ID card is always transmitted as a 16 character value. If the ID data is shorter, additional padding characters will be added as required. 1.5 Read procedure The type of read procedure supported is indicated by the type code on the nameplate. The nameplate is located on the underside of the housing. Type name Date code ************* 5VDC, +/-10%, max.100mA XX XXXXXXXX-XXXXXX XXXX XX Design version Serial number WA Number Item number Code Reader types PX5 LEGIC prime PX51 LEGIC advant PX7 MIFARE Classic PX71 MIFARE DESFire PX10 HITAG PX15 INDALA / TROVAN 1.6 Components supplied A 1x USB PC Reader B 1x manual C 1x CD with reader software D 1x USB cable A B DORMA D C  Installation Manual USB PC Reader USB PC Reader 2. Connection 2.1 Connecting the USB PC Reader The USB PC Reader's USB cable connects to a PC's USB port. The operating system's original virtual COM port driver is used. This should be installed when you first plug in the USB PC Reader. The first time you plug in the USB PC Reader, a search is done for an available COM port. This reader then always occupies the COM port number that is found. (Please note: The driver is not signed although it is from Microsoft and is part of the operating system.) If possible, set the following parameters in the operating system's control panel (on the PC): Transfer rate: 9600 Bits/s Data bits: 8 Parity: even Stop bits: 1 (The setting is only made for compatibility with the old system and is of minor importance because the setting is ignored from this point onwards.)  USB PC Reader 3. Commissioning 3.1 Reader software Description: The supplied software is used to read in ID card numbers via an ID card reader. Every ID card number that is read without error will be entered into an interface file (ASCII format). Please note that the interface file only stores the most recently read ID card number. Installation Copy the PC reader software into the desired working directory: ID card reader application: 'pcauswl.exe' Configuration file: 'pcawl.ini' Configuration: Configure the PC reader software via the menu by selecting menu option . • Starting the ID card reader automatically when the application is opened The connection to the ID card reader is automatically created when the PC software is started. • PC ID card reader interface Specifies which of the PC's COM ports the reader is connected to. • Transfer file for ID card number Directory: Name of directory in which the ID card number transfer file should be created (leave empty: the reader software's current working directory) File name: the file name of the ID card number transfer file • ID card number definition The PC reader always outputs the full ID card number as read out from each ID card. Use this setting to specify which portion of the card number read should be recorded in the ID card number transfer file. Start position: The position of the character in the ID card number that should be used as the first character in the transfer file. Number of characters: Number of characters from the start position that should be recorded. The configuration data is saved in the 'pcawl.ini' INI file in the PC reader software's working directory.  USB PC Reader 3. Commissioning 3.2 Reading in ID card data 3.2.1 Starting the reader software 3.2.2 Using the 'Connect PC to reader' button Start the communication with the PC ID card reader (if it does not start automatically when the application is started). 3.2.3 Present an ID card. 3.2.4 The transfer file containing the ID card number will be created and can be evaluated. The ID card information recorded in the transfer file will be displayed in the 'ID card number' field. 3.3 Other software Further functionality is provided by the application software for the various time and access systems. Please refer to the appropriate online help or manual for information on the functionality offered by these systems and how to use them.  3. Commissioning USB PC Reader 3.4 Operating mode The USB PC Reader has a number of operating modes. They are set using the DIP switch SW101 on the USB card. The housing must be opened to access the switch. The antenna is glued onto the housing cover. Care should be taken not to damage the antenna connection cable. All the switches should be set to OFF for the read mode described in this document. Switch 101 1 2 3 Function Operating mode Default off off off 4 5 6 7 8 off off unused off off off Switch 101 1 2 3 off off off Enable Close-Check The Alive Message is DORMA specific off off on Enable Close-Check The Alive Message is a NULL-Character off on off Disable Close-Check off on on free on off off free on off on free on on off free on on on free 10 Function 3. Commissioning USB PC Reader 3.5 Indala-Trovan reader (PX15) The read procedure used by the PX15 reader can be changed using DIP switch SW101 located on the reader module. The housing must be opened to access the switch. Switch 101 1 Function 3 unused off Default 2 off 4 5 6 Reader Function off 1) 1) 1) 7 8 unused off 3801261 ######## ## ## off Switch 101 4 5 6 Function off off off Indala-Trovan (Kombi) off off on 1) off on off Trovan (TIMAC) off on on free on off off Trovan Altkunde (TIMAC) on off on free on on off 1) on on on free Indala (Flexpass) The antenna is glued onto the housing cover. Care should be taken not to damage the antenna connection cable. Trovan (IPEV) 3.6 Mifare DESfire reader (PX71) The read procedure used by the PX71 reader can be changed using DIP switch SW101 located on the reader module. The housing must be opened to access the switch. Switch 101 1 2 Function Default 3 4 5 6 7 8 off off off off unused off off off on Switch 101 7 Function off Normal operation on VT100 terminal operation The antenna is glued onto the housing cover. Care should be taken not to damage the antenna connection cable. 11 3. Commissioning USB PC Reader 3.7 LEGIC advant reader (PX51) 1 1 1 The read procedure used by the PX51 reader can be changed using DIP switch SW101 located on the reader module. The housing must be opened to access the switch. Switch 101 1 2 Function Default 3 4 5 6 7 8 off off off off unused off off off on Switch 101 7 Function off Normal operation on VT100 terminal operation SW101 XX XX XXXXXXXXXX 3801400 The antenna is glued onto the housing cover. Care should be taken not to damage the antenna connection cable. 12 USB PC Reader EG Konformitätserklärung EC Declaration of Conformity CE Déclaration de conformité 13 USB PC Reader 4. Technical data Technical data Available reader systems • LEGIC prime, LEGIC advant • MIFARE Classic, MIFARE DESFire • HITAG (HITAG1, HITAG2, EM4102, EM4450) • INDALA-TROVAN Display elements 1x LED (green) 1x LED (yellow) Read distance INDALA-TROVAN: max. 8 cm (approx.) MIFARE: max. 4 cm (approx.) LEGIC: max. 5 cm (approx.) HITAG: max. 8 cm (approx.) Storage temperature -20 °C to +70 °C Interfaces USB Protection rating IP 30 Interface connection USB cable length type 1.5 m Dimensions L118 x W79 x H19 (mm) USB ports power supply 5 V DC, max 100 mA Weight Reader unit approx. 200 g Operating temperature 0 °C to +45 °C General design EN 60 950-1, protection class III We reserve the right to make technical modifications and improvements that assist the further development of our equipment. DORMA Time + Access GmbH Postfach 21 01 85 • D-53156 Bonn • Mainzer Straße 36-52 • D-53179 Bonn Tel. +49 (0) 2 28/85 54-0 • Fax +49 (0) 2 28/85 84-1 75 • www.dorma-time-access.de DORMA GmbH + Co. KG Postfach 40 09 • D-58247 Ennepetal • DORMA Platz 1 • D-58256 Ennepetal Tel. +49 (0) 23 33 / 793-0 • Fax +49 (0) 23 33 / 79 34 95 • www.dorma.com 14 USB-PC Reader Notes 15