Transcript
GORILLA GADGETSTM JungleConcert
TM
Premium Bluetooth
User Guide
TM
Headphone
Table of Contents 1. Introduction
3
2. Safety
3
3. Package Contents
4
4. Control Diagram
4
5. User Guide 5.1 General Use 5.2 Pairing to a mobile phone or other BluetoothTM–enabled device 5.3 Pairing to a computer 5.4 Wired Line-in Input 5.5 USB Audio Input 5.6 Charging your JungleConcertTM Stereo Headphone
5 5 7 8 8 8 9
7. Service and Support
10
8. Frequently Asked Questions (FAQ’s)
10
1. Introduction Whether you’re in the rain forest or deep in the urban jungle, you’re TM TM going to love your new JungleConcert Bluetooth Stereo Headphones. This brief instruction manual will help you become familiar with all the features that are built into your headphone, and we strongly advise you to read it before attempting to connect. But if you’re like 99% of the other gorillas out there, you’ll pop open the package, go as far as you can, and then check out this booklet when you get stumped. That’s OK, too, but don’t say we didn’t tell you so…
2. Safety It’s like, really hard to hurt yourself with a battery-driven stereo headphone, but someone will figure out a way, so we’re going to tell you the obvious here: 1)
Read the manual before you use the headphone. It has a lot of good information in it.
2)
Watch for sharp edges, uneven surfaces, or metal parts that could scratch or cut you.
3)
Don’t try to modify, repair, or dismantle this headphone. Doing so could result in fires, electric shocks, complete destruction of the headphone or worse, all of which will not be covered under your warranty. So don’t do it. Send it to us if it’s under warranty, and we’ll either replace it or repair it for you.
4)
Don’t use solvents or volatile liquids to clean your JungleConcert headphone.
5)
Don’t use your JungleConcert Headphone in any area that could be considered hazardous – especially those areas where you need to be hearing what’s going on around you.
3. Package Contents •
JungleConcert Bluetooth
•
USB Charging Cable
•
Audio Cable
•
User Manual
•
Carrying case
TM
4. Control Diagram
Stereo Headphone
5. User Guide 5.1 General Use To do this: Turn on
Follow these instructions: Press the MFB button for 3 seconds when the device is off. A pink LED will slowly flash and you’ll hear a tone beeping.
Enter the Pairing Mode
Press the “+/-“ button with the power on, and hold it for 6 seconds. A white and red LED will alternately flash and you’ll hear a two beep tone.
Pairing
You can pair with your mobile phone or any other Bluetooth enabled master device
Turn Off
Press the MFB button for 3 seconds when the device is in the ‘on’ mode. You’ll hear a tone beep and all the LED lights will go off.
Low Battery Warning
The red LED will flash continuously.
Charging
Plug your USB (supplied) cable into the built-in port
Answer a Call
Touch the MFB button when you know there’s a call coming in.
End a Call
Same thing. Touch the MFB button and you’ll disconnect the call.
Shift between two devices
Double press the MFB button to transfer from one device to another; ie.to answer a call or to go from a call to another
device.
Reject a call
Press the MFB button for 1-2 seconds to reject an incoming call.
Volume Up
A short press on the “+” button will take the volume up a notch.
Volume Down
A short press on the “-“ button will knock the volume down a notch.
Next
A short press on the “>” button will advance you to the next selection.
Previous
A short press on the “<” button will take you back to the previous selection
Battery Power Indication
When you pair to an iPhone, the battery power on your headphone will be indicated on your iPhone.
Play/Pause
A short press of the “>” key will play or pause the music when your headphone is connected.
Multi-point Connection
In pairing mode, short press the “>” button to enable the multi-point option; double press the MFB to disable the multipoint option.
Factory Reset
Long press both “>” and “<” when you’re in the pairing mode to reset or clear the paired device list.
5.2 Pairing to a mobile phone or other BluetoothTM–enabled device TM
To use your JungleConcert Bluetooth Headphone, you must first pair your TM headphone with a phone or a computer that is also Bluetooth enabled. Once your headphone is paired to a specific phone or computer, it will remain paired and will automatically recognize each other whenever they are within range. TM
1)
Turn on your phone and make sure the Bluetooth activated
function has been
2)
Turn on your JungleConcert Headphone and go to the pairing mode
3)
Search the list of Bluetooth devices available on your phone by following your phone’s instructions. Refer to your phone’s instruction manual if you still have it.
4)
After a few seconds, the phone will detect the JungleConcert headphone as a ‘discovered’ device. Select it, and follow your phone’s instructions to select this particular pairing.
5)
Your phone may request a Passkey or PIN; enter 0000 as your PIN or Passkey.
6)
Your phone will confirm the pairing. Press ‘Yes’ or ‘OK’ if it asks.
TM
Select the option to connect with the device from your phone’s screen. 7)
You can play music, watch TV or a movie, or play games on your phone while listening to the audio on your JungleConcert Stereo Headphones. You can control the audio from the headphone using the touch control panel on the side.
5.3 Pairing to a computer
TM
1)
Make sure your computer is Bluetooth enabled. If it is not, you will TM need to acquire a Bluetooth adapter. Once it is in place, make sure TM the Bluetooth function is activated.
2)
Turn on your JungleConcert Headphone and go to the pairing mode
3)
Open the Bluetooth software that is installed on your computer, and TM then select the option that searches for Bluetooth devices. Refer to the software manual if you still have it.
4)
After a few seconds, the name of your device will be listed on your computer as a ‘discovered device”.
5)
Select the device’s icon and click the right-side button on your mouse to choose the ‘Pairing’ option; then select “connect with audio device”.
6)
Go to your media player, or whatever program you want to transfer the audio from, and listen in complete privacy to the clean, clear sounds.
TM
5.4 Wired Line-in Input Your JungleConcert Stereo Headphone supports a 3.5mm audio jack line-in cable if you should desire to go that way. The only reasons we can think of are if the batteries go low, or if wireless devices aren’t permitted wherever you are. When you use the line-in cable, the TM Bluetooth option will automatically power off.
5.5 USB Audio Input You can charge your JungleConcert Stereo Headphone and listen to music at the same time when you connect it with the USB cable to your computer.
5.6 Charging your JungleConcert Stereo Headphone Your Headphone uses a USB – to – Micro USB charger. Make sure that your JungleConcert headphones are fully charged (at least 6 hours) before your first use. When the headphone is charging, you’ll see a red LED light in the constant ‘on’ mode. When charging is complete, the red LED will go off, and a white LED will go on.
Warning: You must fully charge your JungleConcert Headphone if it has not been used for more than 12 months.
6. Technical Specifications
7. Service and Support If you believe your JungleConcert Headphone is not working properly, please contact Gorilla Gadgets Customer Service. Our contact information is available at www.gorillagadgets.com.
8. Frequently Asked Questions (FAQ’s) The headphone doesn’t show any power, even when it’s turned on. Make sure you’ve charged the battery for up to 6 hours when you use it for the first time. The LED will be a solid red while charging, and will turn white when it’s done charging. There is no sound coming from my headphone Check the connection between your headphone and your phone or computer/laptop. If the connection is not established, follow the instructions to reconnect. Make sure the headphone is paired or connected with your target phone or other master device. I can’t seem to connect the headphone to a second device Set the headphone to ‘pairing mode’, and do a short press on the “>” button to multipoint mode. Connect the headphone to phone #1. Press the “+” and “-“ buttons for 6 seconds to enter the pairing mode again and then connect the headphone to phone #2. Then use phone #1’s paired device list to reconnect to the headphone.
