Transcript
User Guide TRACK
MODE
VOL
WP-ID5BT
CORPORATE: SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 WEB: www.SSVworks.com Phone: 818-991-1778 FAX: 866-293-6751 © Copyright 2014 SSV Works
WP-ID5BT-UG Rev. A 2-14-14
Weatherproof Audio System with Bluetooth Audio
Safety Information
Reset
Do not attempt to disassemble or repair the WP-ID5BT yourself. Please call SSV Works for technical assistance or repair information. Changes or modifications to the WP-ID5BT not authorized by SSV Works will void the warranty.
WARNING:
Remove fuse from SSV Works fuse holder located at the battery before charging the battery or jump starting the vehicle.
To reset the microprocessor to the original factory settings:
TRACK
MODE
VOL
1. Press and hold the MODE button until “bA 0” appears in the display.
Button Locations and Functions 1
Hold
Resetting the WP-ID5BT:
2
3
TRACK
MODE
4
2. Press the MODE button four more times and “CLr” will appear in the display.
VOL
Reset Indicator 5 3. Press either the VOL or button and the system will reset the microprocessor to the original factory settings.
TRACK
MODE
VOL
or
6 1. Mute or Play/Pause Button ( ): - Radio Mode (rAd): Press to mute the audio, press again to restore the audio. - Auxiliary Input Mode (AU In): Press to mute the audio, press again to restore the audio. - Bluetooth Mode (bt): Press to pause the track, press again to resume playing the track. - iPod Mode (IPOd): Press to pause the track, press again to resume playing the track. 2. Track Button ( ): - Radio Mode (rAd): Scan Tuning: Press and release, the tuner will scan to the next strong station and stop. Manual Tuning: Press and hold until the desired radio station is tuned-in. - Auxiliary Input Mode (AU In): No function.
3. Mode Button (Mode): Press and release the button to switch between the available sources: radio (rAd), auxiliary input (AU In), Bluetooth audio input (bt) and iPod (IPOd). - Mode Button (Audio Adjustment): Press and hold for 3 seconds to enter the audio adjustment modes: bass, treble, balance and fader. (See Sound Control section for more information). 4. Volume Button ( ): Press to decrease the volume or press to increase the volume. 5. Door Release Handle: Lift up on door handle to open the door. 6. Dome Light Button : Press and release the button to turn on the built-in dome lights, press again to turn off.
- Bluetooth Mode (bt): Press to select a higher or lower track. - iPod Mode (IPOd): Press to select a higher or lower track. 2
11
Button Locations and Functions
Built-in Dome Light Operations Dome Light Button : Built-in LED Dome Lights: Press and release the button to turn on the built-in dome light, press again to turn off.
TRACK
MODE
7
VOL
TRACK
MODE
VOL
8
Built-in Dome Lights
Memory Retaining the Memory: In order for the WP-ID5BT to remember the current radio station and audio settings the unit must be turned off first before turning the vehicle off. To turn the audio system off press the button and the display will become blank.
9 10 11 TRACK
MODE
VOL
12
7. 3.5mm Jack: Plug the 3.5mm jack into a device (MP3 or phone) with a 3.5mm socket. The WP-ID5BT will not control the device, it simply allows the audio to be played through the system.
10. Display Area: This area displays mode information. In the radio mode the radio frequency is displayed.
8. Mounting Straps: Straps your device securely inside the unit. Built-in LED Dome Light
12. Power Button ( ): Press to turn the unit on and off.
11. Built-in LED Dome Light
9. 30-pin Connector for Apple Products: Plug the 30-pin connector into an iPod, iTouch or iPhone. Use the track button to select the desired song. Note 1: Will work with Apple approved 30-pin to lightning adapter. (Cable version) Note 2: The WP-ID5BT can not select menu items.
10
3
Sound Controls
FM Radio Operations
Volume Control: Increase the volume by pressing VOL button. Decrease the volume by pressing the VOL button. The volume level will appear in the display.
Increase TRACK
MODE
VOL
Decrease
Selecting the Play Source:
1. Press and hold the MODE button until “bA 0” appears in the display.
TRACK
MODE
VOL
VOL
TRACK
MODE
VOL
Display
Scan Tuning: Press and release or TRACK button and the tuner will scan to the next strong station and stop. The frequency will appear in the display area.
Hold
MODE
Press the MODE button until “rAd” appears in the display.
Volume Level
Bass Control:
TRACK
Manual Tuning: Press and hold or TRACK button until the desired radio station is appears in the display.
Display
Bass Level
Switching from US to OCEANIA Radio Tuning 2. Press the VOL buttons to increase or decrease the level of bass. The bass level will appear in the display. bA 7 = Maximum bass bA 0 = Neutral bass bA-7 = Minimum bass After 5 seconds control reverts back to volume control.
4
Increase TRACK
MODE
2nd
Hold
1st
Note: Do not change if using in North America. TRACK
MODE
VOL
VOL
Decrease
1. Press the MODE button until “rAd” appears in the display. 2. Press and hold the VOLUME button first then at the same time press and hold the MODE button for approximately 5 seconds until “SEt” appears in the display. 3. Press the button on the front panel to enter setting menu. 4. Press TRACK button to change the display from “US” to “OCEA”. 5. Press the button on the front panel to confirm the change.
9
Bluetooth Operations Pairing Bluetooth Devices: 1. Open the Bluetooth setup program on the mobile device and activate the Bluetooth feature. 2. Press the
Sound Controls (continued) Hold
Treble Control: TRACK
MODE
VOL
button to turn on the WP-ID5BT.
1. Press and hold the MODE button until “bA 0” appears in the display.
TRACK
MODE
VOL
2. Press the MODE button one more time and “tr 0” will appear in the display.
3. Press the MODE button until “bt” appears in the WP-ID5BT’s display. 4. Once the Bluetooth mode is selected “PAIr” will appear in the display. 5. From your mobile device scan for available devices. Select ”SSV ID5BT” to connect to the unit. 6. When the mobile device has been paired “PLAY” will appear in the WP-ID5BT’s display and audio can be heard through the speakers.
Treble Level
Note 1: A previously paired Bluetooth mobile device will automatically connect to the WP-ID5BT when “bt” is selected using the MODE button (if it is within range). Note 2: If the Bluetooth mobile device is already paired with the WP-ID5BT, select “SSV-ID5BT” on your phone and touch “Connect”.
3. Press the VOL buttons to increase or decrease the level of treble. The treble level will appear in the display.
MODE
VOL
Decrease
tr 7 = Maximum treble tr 0 = Neutral treble tr-7 = Minimum treble After 5 seconds control reverts back to volume control.
Bluetooth Operation: Mode Selection: Press the MODE button until “bt” appears in the display.
Increase TRACK
TRACK
MODE
VOL
Play/Pause Button: Press the button to pause the Bluetooth playback, “PAUS” will appear in the display. Press the button again to resume playback and “PLAY” will appear in the display. Changing the Track: Press the TRACK button to select a higher track. Press the TRACK button to select a lower track. Sound Controls: Use the sound controls on the WP-ID5BT unit to adjust the volume and sound quality. Note: For optimum sound quality make sure the media volume on the device is set at 75% or greater.
Hold
Balance Control: 1. Press and hold the MODE button until “bA 0” appears in the display.
TRACK
MODE
VOL
2. Press the MODE button two more times and “L = r” will appear in the display.
Balance Level
8
5
Sound Controls (continued)
iPod, iTouch or iPhone Operations Left Speaker
Balance Control: (continued) 3. Press the VOL buttons to adjust the output of the left and right speakers. The balance setting will appear in the display.
TRACK
MODE
VOL
Right Speaker
L-r - = Equal sound left and right r 7 = Right speakers only L 7 = Left speakers only
iPod, iTouch or iPhone Operation: 1. Plug your iPod, iTouch or iPhone into the 30-pin connector.
MODE
VOL
Warning: DO NOT plug in the 3.5mm jack when the 30-pin connector is plugged in. 2. Secure the iPod with the mounting straps. 3. Close the weatherproof door. 4. Turn on the WP-ID5 by pressing the button. 5. Press the MODE button until “IPOd” appears in the display. The iPod will automatically start playing. 6. Press the TRACK buttons to select the desired track.
After 5 seconds control reverts back to volume control.
TRACK
30-Pin Connector
Note 1: Press to pause the track, press again to resume playing the track.
1. Press and hold the MODE button until “bA 0” appears in the display.
Note 2: If using a newer iPod or iPhone with “Shake to Shuffle” you will need to go into settings and turn this function “Off”.
Hold
Fader Control: TRACK
MODE
VOL
Note 3: You may receive the “this accessory is not made to work with iPhone” message just press “NO” and the device will function normally.
2. Press the MODE button three more times and “F=r” will appear in the display.
Auxiliary Input Operations Fader Level 3. Press the VOL buttons to adjust the output of the front and rear speakers. The fader setting will appear in the display. F-r - = Equal sound front and rear r 7 = Rear speakers only F 7 = Front speakers only After 5 seconds control reverts back to volume control.
TRACK
MODE
VOL
Front Speakers Rear Speaker
3.5mm Audio Input Operation: 1. Plug the 3.5mm jack into your phone or MP3 player. 2. On your device select the desired track, press play and set the volume between 80-90%. 3. Secure the device with the mounting straps. 4. Close the weatherproof door. 5. Turn on the WP-ID5BT by pressing the button. 6. Press the MODE button until “AU In” appears in the display. The audio from your device can now be heard thru the speakers.
TRACK
MODE
VOL
3.5mm Jack
Note in Auxiliary Mode: The WP-ID5BT does not control the device, it simply allows the audio to be played through the system.
6
7
