Transcript
USER MANUAL 2AMDI515TPBS
USER MANUAL 2AMDI515TPBS SUBJECT INDEX: DESCRIPTION TECHNICAL SPECIFICATION DEVICE POWER SOURCE AND CONNECTION TO THE LOAD PUSH OPERATION MINIMUM BRIGHTNESS LEVEL CALIBRATION BLUETOOTH MODE
www.nectogroup.com
pag|1
USER MANUAL 2AMDI515TPBS
DIMMER MONOCANALE TRIAC IGBT “CARICO ZERO” BLUETOOTH
2AMDI515TPBS
TECHNICAL NOTES - Mono channel Dimmers with Output phase cut. - Input Range: 80-230V AC. - *Verify the compliance with electronic led power supply and PFC and THD specification. Eventually reduce the power output rate. - Controllable with Android/iOS app IOT LIGHT. - Input Controls: Insulated Push button x1, Bluetooth LE x1. - Printed Circuit UL. - Protection Class: IP20. - Standard Dimension 40x45x22 mm. - Open circuit protection. - Surge voltage protection. - Over current protection. - Over temperature protection.
PULSANTE N/O ISOLATO NO isulated switch
CONTROL INPUTS INSULATED PUSH BUTTON
BLUETOOTH LE
X1
X1
MAX OUTPUT CURRENT (*) DA 0A A 1A
Mono channel Dimmers with Output phase cut. Input Range: 80-230V AC. Controllable with Android/iOS app IOT LIGHT.
www.nectogroup.com
pag|2
USER MANUAL 2AMDI515TPBS
CODE
INPUT VOLTAGE
(MAX) OUTPUT CURRENT
n. OUTPUT CHANNELS
MAX OUTPUT POWER
CONTROL INPUTS
CASE
DIM.
2AMDI515TPBS
80-230V AC
DA 0A A 1A
1
240W @ 240V AC*
INSULATED PUSH BUTTON X1 BLUETOOTH LE X1
YES
40X45 mm h 22 mm
www.nectogroup.com
pag|3
USER MANUAL 2AMDI515TPBS
DEVICE POWER SOURCE AND CONNECTION TO THE LOAD
WIRING DIAGRAM 2AMDI515TPBS 5 WIRES (RECOMMENDED) - FIGURE N. 1 The 2AMDI515TPBS dimmer has to be connected according to the diagram shown in FIG. 1. In particular: - connect the power source to the Input L and N terminals - connect the load between the Output L and N terminals - connect a normally open button (N.O.) between L (line) and SW L terminal
WIRING DIAGRAM 2AMDI515TPBS 4 WIRES - FIGURE N. 2 The 2AMDI515TPBS dimmer has to be connected according to the diagram shown in FIG. 2. In particular: - connect the power source to the Input L and N terminals - connect the load between the dimmer N Output terminals and L (line) of the system - connect a normally open button (N.O.) between L (line) and SW L terminal
In this configuration the load is not protected by the internal fuse of the 2AMDI515TPBS dimmer.
www.nectogroup.com
pag|4
USER MANUAL 2AMDI515TPBS
PUSH OPERATION Once you connected a normally open button as shown in FIG. 1, you can dim the load (incandescent lamps and/or led dimmable phase cut devices) in the following way: PUSH interface operation Single Click (rapid press (<1sec)) - Turns on or off the output (ON/OFF). Double Click (rapid press (<1sec)) - Sets maximum brightness (output= 100%) Long Press (long press (>1sec)) - If the dimmer is in OFF position, it sets the output to the minimum value (default= 1%) - If the dimmer is in ON position, the long press enables the output dimming (up/down).
ATTENTION! IN ORDER TO MAKE THE DIMMER OPERATE CORRECTLY IT IS IMPORTANT TO KEEP THE POWER CABLE BETWEEN THE BUTTON AND THE DIMMER AS SHORT AS POSSIBLE. IN CASE OF ANY MALFUNCTION REGARDING FALSE POSITIVE OR NEGATIVE ON THE BUTTON, IN PARTICULAR WHILE USING VERY LONG CABLES ON THE BUTTON OR DYSFUNCTIONAL SYSTEMS YOU ARE ADVISED TO INSTALL A MONOSTABLE RELAY CONNECTED LOCALLY TO THE DIMMER (FIGURE 3).
WIRING DIAGRAM 2AMDI515TPBS WITH RELAY - FIGURE N. 3
www.nectogroup.com
pag|5
USER MANUAL 2AMDI515TPBS
MINIMUM BRIGHTNESS LEVEL CALIBRATION OPERATION TO BE CARRIED OUT ONLY BY EXPERT OR QUALIFIED OPERATOR Some line voltage LED loads require a calibration of the minimum brightness level to avoid flickering or flashing. On 2AMDI515TPBS dimmer it is possible to calibrate the minimum level of brightness through the hole positioned under the casing. To lower or raise the minimum brightness level it is necessary (with a powered device) to access to the hole with a plastic plug or anyway not conductive material and act on the inner button in this manner: Long Press (long press (>1sec)) If the dimmer is in ON position, the long press enables the output dimming upwards. Another long press enables the output dimming downwards. The level set by the calibration plug will be the minimum level at which the dimmer will set the output. Starting from the v.2.0 firmware you can adjust the brightness level using the Necto Group app.
www.nectogroup.com
pag|6
USER MANUAL 2AMDI515TPBS
BLUETOOTH MODE In order to activate this mode of control/operation it is necessary to install the Necto Group App on the Android or iOS device that you want to use for the 2AMDI515TPBS dimmer control and disconnect any 0-10V (1-10V) inputs or potentiometer connected to the dimmer. The implemented features are: Switching on and off and the brightness level control of each individual light point. Ability to group together and control several light points with just a simple command. Creation and recall of your favourite lighting sceneries. The system management from a single simplified user interface. THE BLUETOOTH LE CONNECTION DOES NOT REQUIRE PAIRING PROCEDURE Necto Group App features (*depending on the device only some functions may be available) Dimmer management at 1 or 4 channels with different modes of operation: - Mono channel - 4 synchronized channels - RGB (3 channels or 3 zones) - RGB + White (4 channels or 4 zones) - Dynamic White
www.nectogroup.com
pag|7
USER MANUAL 2AMDI515TPBS
In order to install the app on your Apple or Android device you need to scan the desired QRCode to be automatically redirected to the IoT Light application.
As an alternative you can download the app by clicking on one of two links below: Apple: https://goo.gl/QezZ5S Android: https://goo.gl/5RKYmm
www.nectogroup.com
pag|8
