User Manual

Transcript

User Manual MM-CTXDAK Cell Master Double Accel Black MM-CTXDAB Cell Master Double Accel Blue www.muchmoreracing.net CELL MASTER DOUBLE ACCEL Thank you for purchasing Muchmore Racing Cell Master Double Accel. Cell Master Double Accel is the world's smallest 2-port charger/discharger. All the features tested and completed by our Team of R&D, Factory team drivers and ISTC World Champion Marc Rheinard. Cell Master Double Accel is designed for expert R/C car drivers; it gives a great race time. FEATURES ● Dual 200-watt(100+100) charging circuits 2-port 200 watts (100W +100 W) charging circuit. Cell Master Double Accel ground breaking charger features 200 watts of power via dual 100+100watt circuits allowing for simultaneous charging of two batteries up to each 10 amps. ● Super compact dual-port charger Muchmore Racing R&D team has succeeded to make the world best compact dual-port charger. It is the fine compact charger with high-tech designed balancing circuit, constructed dual charging system. Very small size, light weight make easy to move on your pit table, can take full advantage of the space. ● High-efficiency charging current reduction technology system Muchmore Racing R&D Team developed high-efficiency currents boost system. For example, when LiPo 2S 10A charge batteries, currents is only required 8A. Do not need a high-capacity power supply. ● High sensitivity touch button system Adopting a very high sensitivity touch button for each menu, you can run briefly. Also prevent the penetration of foreign substances. This system ensures the stable operation of the button on dusty environments such as off-road stadium. ● Quick Easy UI, Fast response Designed UI to use easily is based plenty race experience. Fast response time will help you to conveniently charge. ● Each channel status LED indicator Easier to check charging status; charging, discharging, stand-by, complete, at a glance by Dual blue state indicator LED. ● Intuitive channel button and channel status indicator Under any circumstances, you may want to move the channel to the one-touch. ● Internal resistance view of Lithium battery packs Adopting a new internal resistance, test each cell individually and provides Individual cell and total pack resistance values so you can check the condition of your Lithium battery packs. ● Voltage meter Individual cell and total pack volt shows at a glance. You can check the voltage of the battery before a race. ● Built-in TAMIYA Lithium battery balancing port The world Tamiya R/C race certified Lithium battery can be charged immediately without conversion connector. ● Temperature controlled cooling fans Use Low-noise/high-performance dual cooling fan. Temperature controlled system make the effectual cooling condition. ● USB Firmware upgrade system Muchmore Racing CTX Link™ software you can easily upgrade to the latest firmware. The new firmware for the future simply by updating, you can use the latest features without discomfort. ● Special black back light LCD display All this technology is accessible through an easy-to-read Special black back light LCD display. ● Ready to Race charging Includes high precision Special 2P Balance Charging Lead, can charge directly without conversion connector. ● Safety circuit board and software design When charging NiCd or NiMh, you can set the upper limit of charge current to avoid damage or explosion from high current feeding. If you set the limit of battery temperature the process will be expired forcibly when the limit has reached. Prevent reverse connection of the battery to prevent damage to the equipment and a built-in safety circuit. When you do short-circuits between the output charge lead , LCD screen will let you know. (Optional part : MR-DATC Cell master double accel temp sensor) Specifications Dimensions Weight Input Circuit Power Charge Current Current Drain of Balancing LiPo NiCd/NiMh Cell Count LiPo/LiFe Pb Battery Voltage Discharge Rate Power Requirement Keys Cooling LCD monitor SUPER COMPACT DUAL PORT CHARGER/DISCHARGER 5.1 x 4.5 x 1.9 in (129 x 115 x 49 mm) 18.3oz (520g) DC 11.0 - 15.0V 100W Max charge x 2, 10W Max discharge x 2 0.1 - 10.0A x 2 200mAh/Cell 1 - 17 Cell 1 - 6 Series 6 - 30V 0.1 - 1.3A x 2 10 - 15V DC Power Supply (200 Watt minimum, 250 Watt suggested) 6 button / High sensitivity electronic touch button IC controlled dual fans 16 x 2 lines Black backlight LCD display 1 Muchmore Racing Co., Ltd. Danger/Warning This is not a Toy. Keep out of reach of small children. This product is intended for users over 14 years of age. During the use, Heatsink and case will heat up. Please use carefully. If you use this product to wrong way, it can cause fire and serious damage or injury. Please use carefully and remain vigilant at all times. Pay close attention to the following safety precautions as improper Muchmore Racing doesn’t owes any responsibilities to the burns or fires caused by careless use. ※Please Do not disassemble or modify this product. * Recommended charging current of each battery may vary depending on the manufacturer. Use them After confirming the correct selection of currents. * It is only for DC 12V input, Never use a household power outlet. * Stable output Muchmore Racing Power Master World Edition 2 Evo's are recommended. Over 14 years of age * Cell Master Double Accel only for NiCd, NiMh, LiPo, LiFe, Pb, do not use other battery. It causes huge damages. * Please be careful of + (red) , - (black) Input and Output wires, Do not connect in reverse. * Do not use other purpose except charging and discharging. * Please stick Thermo Sensor to battery during Charge/Discharge. * Please do not leave around when charge/discharge. * Please stop charging when noise came from the battery or overheat. * When you charge the Lithium batteries, you have to use Safety bag. * Please do not handle this product in Wet hand * Do not set aside flammable objects and thermal deformation material in the vicinity of the device. * Please do not cover anything in front of cooling air holes. * Please do not insert any bolts, washers in cooling air holes. * Please keep away from water/salt water. * Please do not use the product in places where the product will get hot such as under direct sunlight. * Please do not drop the product and avoid strong shocks or impacts. Names of parts and components LCD Display Channel LED Channel Button Touch Panel State LED ESC - Set Cancel / Back Output Port 2 DOWN - Check settings or data reduction UP - Setting up or data verification Temp Sensor 1 TAMIYA LiFe Balancing Port 1 ENTER - Fixed / Forward / Charge,Discharge start / End Output Port 1 Balance Port 1 -Includes connectorsDC In put wire XT60 1pc Cell Balance Multi adapter AL Type 1pc TX and RX Charging Lead 1pc TX and RX charge connector. Ultra 2P Connector Charging Lead 1pc Special 2P Balance Charging Lead 2pcs Double-sided tape for Power supply fixing Balance Port 2 TAMIYA LiFe Balancing Port 2 Colling Fan CTX Link™ USB Port Input (DC12V) Port Temp Sensor 2 LED STATE & Channel selection STATE LED BLUE CH LED RED LED STATE(BLUE) Lighting Flashing Processing Finished Off Flashing Ready SUPER COMPACT DUAL PORT CHARGER/DISCHARGER Channel selection Button Press button to change the display of each channel. Even during the charge and discharge, it can move other channel. Channel CH1 or CH2 is selected and one of Red LED will turn light on. Error 2 Muchmore Racing Co., Ltd. User Menu Charge Normal Basic charging type of LiPo battery. In normal we recommend this mode. Storage Plan to storage LiPo battery more than 2 weeks. We recommend this mode. LiPo CEV Cut End Voltage Discharge Charge Discharging LiPo battery mode Normal Basic charging type of LiFe battery. In normal we recommend this mode. Storage Plan to storage LiFe battery more than 2 weeks. We recommend this mode. LiFe CEV Cut End Voltage Discharge Discharging LiFe battery mode Charge Basic charging NiCd/NiMh mode NiCd/NiMh Discharge Basic discharging NiCd/NiMh mode Charge Basic charging Pb (lead) mode Pb(lead) Discharge Basic discharging Pb (lead)mode Volt Meter Voltage measurements for each cell and total of LiPo, LiFe battery pack LiPo On/Off LiPo Menu yes / no setting LiFe On/Off LiFe Menu yes / no setting NiCd/NiMh On/Off NiCd / NiMh Menu yes / no setting Pb(lead) On/Off Pb (lead) Menu yes / no setting Volt Meter On/Off Volt Meter Menu yes / no setting Key Tones Sound when you press the button yes / no setting Key Timer Charge / discharge time set alarm shutdown and error messages User Setting Safety Timer Charge / discharge the safe shutdown time set Setting the temperature display (Celsius ℃, Fahrenheit ℉) Temp Unit Battery End Temp Charge / discharge, the battery temperature cut set Power Current The minimum capacity of the external power supply to set Power Voltage The external power supply voltage to set the minimum SUPER COMPACT DUAL PORT CHARGER/DISCHARGER 3 Muchmore Racing Co., Ltd. LiPo, LiFe Batteries charging and discharging LiPo, LiFe Mode is only suitable for charging and discharging Lithium batteries. Do not use this mode to other battery. Actual battery during charging and discharging must match the reference. If not match the battery, also in case of overcharging, over discharging, it has huge damage and risk battery explosion. Charging and discharging function is only for LiPo, LiFe battery. Do not use the other type of batteries. LiPo, LiFe Charge ◈ EP ◈ ◈ EP ◈ ◈ Charging current *LiPo* 1 Charge Discharge - select menu 1 LiPo Set Charge and press Select LiPo or LiFe and press Enter button 6.5A Normal Charge Mode button EP ◈ 2S(7.4V) 3000mA Battery cells Charging Capacity Connect the battery And If you want to cell balance charge, connect the Cell balancer too. ◈ Information of STEP 3 LCD Charging Current : Set the charging current to charge the battery, enter the value of the amp. LiPo, LiFe batteries are recommended to charge 1C normally. (3000mAh battery is 3.0A charge) : Select the number of charge the battery pack, specify the number of cells. If you change the number of cells in the pack voltage will be displayed automatically. : There are three modes in LiPo, LiFe charging. Select the desired charge mode by buttons. Charge Mode Charging Capacity : limit capacity of charging. Function of Limit the charging capacity, also it can be turned off. Battery Cells ● Charging Mode Normal Basic charging type of LiPo, LiFe battery. In normal we recommend this mode Storage Plan to storage LiPo, LiFe battery more than 2 weeks. We recommend this mode. Over-discharged batteries cause damage. To avoid this, the initial voltage of the battery and keep the correct voltage to detect the state of the mode is automatically charged and discharged. CEV (Cut End Voltage) CEV charger mode only for LiPo, LiFe, battery. This function makes voltage drop LiPo/4.20V, LiFe/3.60V during the race. It maintains this voltage till you start to drive. LiPo, LiFe discharge rate form and the charging voltage depending on a battery internal resistance value of the battery becomes lowered differently. CEV after charging mode, press the button to set the termination voltage can be charged. The higher the value of the termination voltage, the voltage remains high after charging completed. *Use Each LiPo, LiFe pack in accordance with the appropriate CEV value after test. ● Capacity(mAh) Setup limits value of charge capacity. When the charge capacity is reached the setup capacity (target capacity), charge will be terminate. This is very useful for battery storage or prevent over charging. Basically set capacity value up to 10% higher than battery capacity (ex : battery capacity is 4600, setup to 5100) OFF is turn off this function. ※ Press the button at least 2 seconds after setting all of the charge, it moves to Check Battery with informing battery check on a screen. ● Battery Cell condition check EQU USER 2S(7.4V) 2S(7.4V) EQU USER EQU Auto detect Cell number and Voltage (from Cell Master Double Accel IC) USER Cell number and Voltage from actual user If detecting voltage and actual voltage are same, press button, and start to charge But, if the actual cell number is different from detected cell number, please adjust the cell number in manual. ※ Mismatch cell number will cause battery or device damage, please use carefully. ● Charging information Battery type/ Cell num, Channel Charging currents Charging voltage * Optional charging keys. During the charge, press button shown 3 information on the screen. If not press the button, it moves back to charging mode screen after 5 seconds. 1. Current capacity of each cell 2. Setting value capacity, CEV(Cell End Volt) value 3. EQU Temp(device temperature), BAT Temp(battery temperature) LiPo 6.0A 8.35V CHG 122mA 8:11 Mode state Charging capacity Charging time SUPER COMPACT DUAL PORT CHARGER/DISCHARGER 4 Muchmore Racing Co., Ltd. ● Quit charging, Cancel charging Press the button for 2 seconds during the charging, stops charging, and the status of CHG (channel), End (channel) messages are shown on the intersection. At this point, press the button to proceed the Setup screen. ● Change the value in the charging On-touch the button, blink the charging current. At this time press the button, change the value, and press , it change the charging value without stop charge. ● Display after the end of the charge Setup battery type Finish battery voltage * You can see each information’s on your screen push the button. 1. Each cell capacity 2. Total resistance value of Batteries 3. Each cell resistance. (Press the button, detect the resistance and show on the screen, it need to 5~ 7 seconds to detect) LiPo 0.0A 8.40V CHG 2800mA 12:02 Finish charging capacity charging time Discharging LiPo, LiFe ◈ E ◈ ◈ E ◈ ◈ Discharging current *LiPo* 1 Charge Discharge -select menu 1LiPo Select LiPo or LiFe and press Enter button Set Discharge and press button E 1.0A Cut V ◈ 2S(7.4V) 3.2V/Cell Battery cell number Cell voltage Connect the battery And If you want to cell balance discharge, connect the Cell balancer too. ◈ Information of STEP 3 LCD Discharging current : Set the discharging current, enter the value of the amp. Battery cell number : Select the number of charge the battery pack, specify the number of cells. If you change the number of cells in the pack voltage will be displayed automatically. : Set a finish discharge current of each cell. Cell voltage ※After all discharge setup, press the button at least 2 seconds, it moves to Check Battery with informing battery check on a screen. ● Check battery cell condition EQU Auto detect Cell number and Voltage (from Cell Master Double Accel IC). EQU USER 2S(7.4V) 2S(7.4V) E USER Cell number and Voltage from actual user. If detecting voltage and actual voltage are same, press button, and start to charge But, if the actual cell number is different from detected cell number, please adjust the cell number in manual. E ※ Mismatch cell number will cause battery or device damage, please use carefully. ● Display discharging Battery type/ Cell num, Channel Discharging currents Battery voltage *Optional discharging function key During the discharge, press button shown 3 information on the screen. If not press the button, it moves back to discharging mode screen after 5 seconds. 1. Current capacity of each cell 2. Setting value capacity, Discharging cut Volt value 3. EQU Temp(device temperature), BAT Temp(battery temperature) LiPo 2.0A 8.35V DCH 122mA 8:11 Mode state Discharging capacity Discharging time ● Cancel Discharging Press the button for 2 seconds during the discharging, stops discharging, and the status of CHG (channel), End (channel) messages are shown on the intersection. At this point, press the button to proceed the Setup screen. ● Display after the end of the discharge Setup battery type Finish battery voltage * You can see each information’s on your screen push the button. 1. Each cell capacity 2. Total resistance value of Batteries 3. Each cell resistance. (Press the button, detect the resistance and show on the screen, it need to 5~ 7 seconds to detect) LiPo 0.0A 8.00V DCH 2800mA 12:02 Finish discharging capacity discharging time SUPER COMPACT DUAL PORT CHARGER/DISCHARGER 5 Muchmore Racing Co., Ltd. Charge / Discharge NiCd/NiMh battery NiCd/NiMh mode is covered all kinds of NiCd/NiMh battery. This Mode is only suitable for charging and discharging NiCd/NiMh batteries. Do not use this mode to other battery. Actual battery during charging and discharging must match the reference. If not match the battery, also in case of overcharging, over discharging, it has huge damage and risk battery explosion. Do not use the other type of batteries. About Delta peak for NiCd/NiMh charging, starting the NiCd/NiMh, the peak voltage flew the battery. Its voltage level goes up, it draws Positive delta V and when the battery is fully charged, the voltage level goes down with Negative delta V. This charging way stop charge after check precision converter which perfect detects the voltage decrease and terminates. Delta peak charge is the best way of the NiMh battery charging. NiCd/NiMh Charge ◈ EP ◈ ◈ EP ◈ ◈ EP ◈ Charging current select menu 1NiCd/NiMh Select NiCd or NiMh and press Enter button *NiCd/NiMh* 1 Charge Discharge Set Discharge and press Delta peak button Battery cell number 5.0A 6C(7.2V) D/P:12mV 3000mA Charging Capacity Connect the battery And If you want to cell balance discharge, connect the Cell balancer too. ◈ Information of STEP 3 LCD Charging current : Set the charging current to charge the battery, basically recommend 1C charging SUB-C battery normally. (5,000mAh battery is 5.0A charge) Battery cells : Select the number of charge the battery pack, specify the number of cells. If you change the number of cells in the pack Delta peak : Setup delta peak value. 12 means 12mv, normally start to charge with 2mv (If 6 cell - 6cell X 2mv = 12mv) voltage will be displayed automatically. If the battery's temperature is too low when charging has done, you can increase delta peak value for suitable situation. All batteries have own battery internal resistance and character, this function very useful to charge, for many kinds of battery manufacture. Charge capacity : When the charge capacity is reached the setup capacity (target mAh), charge will be terminate. This is very useful for battery storage. Basically set capacity value up to 10% higher than battery capacity (ex-battery capacity is 4600, setup to 5100) OFF is turn off this function ※Press the button at least 2 seconds after setting all of the charge, it moves to Check Battery with informing battery check on a screen. ● Display charging information Battery type/ Cell num, Channel Charging currents Battery voltage * Optional charging keys. During the charge, press button shown 3 information on the screen. If not press the button, it moves back to charging mode screen after 5 seconds. 1. Setup value / Peak voltage 2. End Temp(End charging temperature), BAT Temp(battery temperature) 3. EQU Temp(device temperature), Delta peak value ChMh 6.0A 8.35V CHG 122mA 8:11 Mode state Charging capacity Charging time ● Quit charging, Cancel charging Press the button for 2 seconds during the charging, stops charging, and the status of CHG (channel), End (channel) messages are shown on the intersection. At this point, press the button to proceed the Setup screen. ● Change the value in the charging On-touch the button, blink the charging current. At this time press the button, change the value, and press , it change the charging value without stop charge. ● Display after the end of the charge Setup battery type Peak voltage * Check the internal resistance of cell and voltage. You can see each information’s on your screen push the button. (Press the button, detect the resistance and show on the screen, it need to 5~ 7 seconds to detect) CdMh 0.0A 8.40V CHG 2800mA 12:02 Finish Charging capacity Charging time SUPER COMPACT DUAL PORT CHARGER/DISCHARGER 6 Muchmore Racing Co., Ltd. Discharging NiCd, NiMh ◈ EP ◈ ◈ EP ◈ ◈ Discharging current *NiCd/NiMh* 1 Charge Discharge -select menu 1NiCd/NiMh Select NiCd or NiMh and press Enter button Set Discharge and press EP 1.0A Cut V ◈ 6C(7.2V) 0.9V/Cell Battery cell number Each cell current Connect the battery button ◈ Information of STEP 3 LCD Discharging current : Set the discharging current, enter the value of the amp. Battery cell number : Select the number of charge the battery pack, specify the number of cells. If you change the number of cells in the pack voltage will be displayed automatically. : Set a finish discharge current of each cell. Each cell current ※After all discharge setup, press the button at least 2 seconds, it moves to Check Battery with informing battery check on a screen. ● Display discharging Battery type/ Cell num, Channel Discharging currents Battery voltage *Optional discharging function key During the discharge, press button shown 3 information on the screen. If not press the button, it moves back to discharging mode screen after 5 seconds. 1. Setting value capacity, Discharging cut Volt value 2. End Temp(End charging temperature), BAT Temp(battery temperature) 3. EQU Temp(device temperature), AVG Voltage CdMh 1.0A 8.35V DCH 122mA 8:11 Mode state Discharging capacity Discharging time ● Cancel Discharging Press the button for 2 seconds during the discharging, stops discharging, and the status of CHG (channel), End (channel) messages are shown on the intersection. At this point, press the button to proceed the Setup screen. ● Display after the end of the discharge Setup battery type Finish battery voltage * Check the internal resistance of cell and voltage. You can see the information on your screen push the CdMh 0.0A 6.20V End1 2800mA 58:02 1. Each cell resistance (Press the button. button, detect the resistance and show on the screen, it need to 5~ 7 seconds to detect) 2. AVG Volt Finish discharging capacity discharging time Charge / Discharge Pb(lead) Battery Pb mode is programmed only for Pb, lead-sulphuric acid, lead-gel battery charging and discharging with nominal volatage 6~30V only. Pb battery only deliver low current, so it cannot possible to quick charge, it needs 12~16 hours by 1/10C. This mode is only for Pb battery, do not use this mode with other type battery. Charge Pb(lead) battery ◈ EP ◈ ◈ -select menu 1Pb(lead) Select Pb(lead) and press Enter button EP ◈ ◈ *Pb(lead)* 1 Charge Discharge Set Charge and press Charging Current Bagic Mode button 0.3A Normal EP ◈ 12.0V 3000mA Battery Cells Charging Capacity Connect the battery ◈ Information of STEP 3 LCD Charging current : Set the charging current, enter the value of the amp. Battery cells : Select the number of charge the battery pack, specify the number of cells. If you change the number of cells Basic mode : Fixed Basic Charging mode Normally Pb battery is recommended to charge 1/10 C (3,000mAh battery is 0.3A charge) in the pack voltage will be displayed automatically. Set a limit charging capacity : When the charge capacity is reached the setup capacity (target mAh), charge will be terminate. This is very useful for battery storage. Basically set capacity value up to 10% higher than battery capacity (ex : battery capacity is 4600, setup to 5100) Function of Limit the charging capacity, also it can be turned off. ※ After all charge setup, press the button at least 2 seconds, it start to charge Battery with informing battery check on a screen. SUPER COMPACT DUAL PORT CHARGER/DISCHARGER 7 Muchmore Racing Co., Ltd. ● Battery Cell condition check EQU USER EQU Auto detect Cell number and Voltage (from Cell Master Double Accel IC) E 6S(12.0V) 6S(12.0V) E USER Cell number and Voltage from actual user If detecting voltage and actual voltage are same, press button, and start to charge But, if the actual cell number(voltage) is different from detected cell number, push and adjust the voltage in manual. ※ Mismatch cell number will cause battery or device damage, please use carefully. ● Display charging information Battery type/ Cell num, Channel Charging currents Battery voltage *Optional charging key During the charge, press button shown 3 information on the screen. If not press the button, it moves back to charging mode screen after 5 seconds. 1. Setting value capacity, charging cut Volt value 2. End Temp(End charging temperature), BAT Temp(battery temperature) 3. EQU Temp(device temperature), AVG Voltage Pb 3.0A 12.0V CHG 1980mA 12:02 Mode state Charging capacity Charging time ● Quit charging, Cancel charging Press the button for 2 seconds during the charging, stops charging, and the status of CHG (channel), End (channel) messages are shown on the intersection. At this point, press the button to proceed the Setup screen. ● Change the value in the charging On-touch the button, blink the charging current. At this time press the button, change the value, and press , it changes the charging value without stop charge. ● Display after the end of the charge Battery type Peak voltage Pb 0.0A 12.0V CHG 3000mA 12:02 Finish Charging capacity * Check the internal resistance of cell and voltage. You can see each information’s on your screen push the button. Charging time Discharge Pb(lead) battery ◈ E ◈ ◈ E ◈ ◈ Discharging current *Pb(lead)* 1 Charge Discharge -select menu 1Pb(lead) Select Pb(lead) and press Enter button Set Discharge and press button E 1.0A Cut V ◈ 6S(12.0V) 1.5V/Cell Ba e y cell Each cell current Connect the battery ◈ Information of STEP 3 LCD Discharging current : Set the discharging current, enter the value of the amp. : Select the number of charge the battery pack, specify the number of cells. Battery cells If you change the number of cells in the pack voltage will be displayed automatically. : Set a finish discharge current of each cell. Each cell current ※After all discharge setup, press the button at least 2 seconds, it moves to Check Battery with informing battery check on a screen. ● Battery Cell condition check EQU USER 6S(12.0V) 6S(12.0V) EQU Auto detect Cell number and Voltage (from Cell Master Double Accel IC) E E USER Cell number and Voltage from actual user If detecting voltage and actual voltage are same, press button, and start to charge But, if the actual cell number (voltage) is different from detected cell number, push and adjust the voltage in manual. ※ Mismatch cell number will cause battery or device damage, please use carefully. SUPER COMPACT DUAL PORT CHARGER/DISCHARGER 8 Muchmore Racing Co., Ltd. ● Discharge Pb(lead) battery Battery type/ Cell num, Channel Discharging currents Battery voltage Pb 1.0A 8.35V DCH 122mA 8:11 Mode state Discharging capacity Discharging time *Optional discharging function key During the discharge, press button shown 3 information on the screen. If not press the button, it moves back to discharging mode screen after 5 seconds. 1. Setting value capacity, Discharging cut Volt value 2. End Temp(End charging temperature), BAT Temp(battery temperature) 3. EQU Temp(device temperature), AVG Voltage ● Cancel Discharging Press the button for 2 seconds during the discharging, stops discharging, and the status of CHG (channel), End (channel) messages are shown on the intersection. At this point, press the button to proceed the Setup screen. ● Display after the end of the discharge Battery type Battery voltage * Check the internal resistance of cell and voltage. You can see the information on your screen push the Pb 0.0A 6.20V End1 2800mA 58:02 1. Check resistance value (Press the button. button, detect the resistance and show on the screen, it need to 5~7 seconds to detect) Finish Discharging capacity Discharging time Volt Meter Volt Meter is function to check each cell voltage and total voltage of LiPo and LiFe. It is very useful to detect difference of each cell, total voltage, condition of charging/discharging. * Quik Volt Meter: Push the ESC button at least 3 seconds in main menu, it moves Volt Meter mode -select menu 1Volt Meter BAT Total Volt 25.12 Select the Volt meter Total voltage When you click the 4.18 4.18 4.19 4.19 4.19 4.19 Each cell present voltage , changed to page. USER SETTING Select User Setting. -select menu 1User Setting Main menu On/Off LiPo On/Off - Key tonesOn / Off - Key timer 5sec Main menu On/Off This is function of customizing; you can make user’s memory. Put your battery and setting on/off function. *Use the button, memorized current function On or Off. Apply menu (LiPo, LiFe, NiCd/NiMh, Pb(lead), Volt Meter) Key tones Sonds on/off Key timer Set a ring buzzer time when error, finishing charge/discharge. If set off, it just indicate LED without sounds. Set Forever, it rings till push the button. Setting mode - Off, 5sec, 15sec, 30sec, Forever SUPER COMPACT DUAL PORT CHARGER/DISCHARGER 9 Muchmore Racing Co., Ltd. Safety timer When the set time is exceeded, quit operation by force. Prevent errors due to the excessive charge and discharge. If the set time is too short, during the process of charging and discharging operations can be terminated. Set the charge and discharge time longer than usual. Ex) Charge 2000mA 1A expecting time : 120minutes x 1.3(about 30% add) = 156minutes. (30-250Min, 10Level) - Safety timer 120Min Temp Unit Change the Notation of Celsius and Fahrenheit. - Temp Unit C /F Battery End Temp 40C - Power Current 10.0A - 25,0A - Power Voltage 10.0V - 12.0V Battery End Temp Using a temperature sensor mounted on left / right of the 3-pin port, stop charge and discharge when the temperature reaches the set temperature. Protect the battery from over charging/discharging. ※ Valid set temperature: 40℃~55℃ (104℉~131℉) * This function needs an option part. (Extra buying) MR-DATS Cell Master Double Accel Micro Temp Sensor Power current Power unit is lower than the setting value, the input power apparatus stops. Power Voltage In case of using car battery to input power, avoid over-charging function. Power unit is lower than the setting value, the input power apparatus stops. Product Warranty MUCHMORE RACING warrants their Cell Master Double Accel to be free from defects in material and workmanship for a period of 120 days from the date of purchase MUCHMORE RACING (or their associated distributors) will repair or replace without charge or refund the purchase price of any product which fails during the warranty period by reason of defect in material or workmanship found upon examination by MUCHMORE RACING to have been the cause of failure. This warranty does not cover any failures attributable to abuse, mishandling, failure to follow operating instruction, alteration or accident, result of normal wear, misuse or improper maintenance. ■ ■ ■ ■ ■ ■ Explosion and Fire The case damage Damage to electronic components and circuit boards A circuit board soldering To receive warranty service, the product of all the parts before the first check and troubleshooting instructions. To obtain warranty service on products purchased on the receipt of the products you need. (If you do not have a receipt, the warranty period is not to be recognized.) ■ For faster delivery failure or defect repairs and for more information, please fill out the address and contact details r Ra . C ., . 502-17 Baengma-ro, ilsandong-gu, Goyang-city, Gyeonggi-do, 410-842, Rep. of KOREA Tel +82-31-903-0487 | Fax +82-31-903-0497 http://www.muchmoreracing.net SUPER COMPACT DUAL PORT CHARGER/DISCHARGER 10 Muchmore Racing Co., Ltd.