User Manual

Transcript

ETK-B2400 User Manual Safety Warnings and Precautions Scope of Warranty and Liabilities • This product is a road safety accessory and the manufacturer is not liable for any losses brought on by malfunctions, loss of data or any other forms of losses from using this product. • This product is an accessory designed for the specific purpose of recording and saving captured video footage of the areas near the vehicle. Certain functions may not be supported depending on the driving conditions and vehicle conditions. The firmware updates for improving performance may result in different performance by each product. The video may not be recorded depending on the conditions in which the device is used. Please use the device only for your reference. The recording may not take place depending on the status of the microSD card. • This device is designed to capture and save accident footages of the vehicle in which the product is installed in. However, it does not guarantee that every accident footage will be recorded. Accidents with very minor level of impact may not activate the impact sensor and the accident may not be recorded as an event footage. • In vehicles that use smart keys, the batteries may discharge while in Parking Mode. 2 Safety Warnings and Precautions Please read the following warnings and cautions thoroughly. These warnings and cautions were made for the safety of the users and to prevent any potential damage caused by improper use. Warning Failure to follow these safety warnings could lead to a serious injury or death. Caution Failure to follow these cautions could lead to an injury or cause loss of property. Do not operate the product while driving. Do not disassemble, or modify the product. Operating the product while driving can lead to driver distractions. If you need to operate the product, do so after pulling over to a safe location. Unauthorized disassembly or modifications of the product can cause product malfunctions. These malfunctions are not covered under the product warranty. Do not cover or place anything on the product, allow for ventilation. Do not operate the product if it has been exposed to debris. It can damage the product and lead to a malfunction. If foreign debris has got on the product, disconnect the power and clean thoroughly with a soft cloth. Note: Use caution if using cleaning solvents. Do not use the product if it is malfunctioning. Only use properly rated fuses for the power outlet. In the event of a malfunction, disconnect the power supply and contact your place of purchase. When you need to replace the fuse, make sure to use a correctly rated fuse. Using a fuse with an incorrect rating can cause a fire. 3 Safety Warnings and Precautions If you need to replace the power cable, mount, or any other part, use original parts offered by the manufacturer only. The consumer is responsible for all malfunctions and accidents resulting from use of unauthorized parts. Obstructing the driver’s field of view can lead to driver distraction. Recommended location for mounting the product, the upper portion of the front windshield, along the central axis of the vehicle. Do not expose the product to moisture or store it under a highly humid environment for an extended period of time. Do not expose the product to the direct heat of the vehicles heating system or other heat-generating appliance. Damage to the product may occur and lead to malfunctions. Exposure to high heat can cause damage to the product and lead to malfunctions. When installing the product, make sure it does not impede with the operation of other onboard devices such as the airbag system. Maintain the ambient temperature to between 0°C and 50°C/32°F and 122°F. Impeding the operation of other onboard devices can lead to an injury. Do not place beverages, chemicals, or other potentially harmful items near the product. 4 When installing the product, make sure it does not obstruct the driver’s field of view. It can damage the product and lead to malfunctions. Temperatures outside this range can lower the performance or damage the product and lead to malfunctions. Do not power off the product abruptly or operate it in an abnormal manner. Doing so can damage the microSD card and the product. Safety Warnings and Precautions Do not touch the product with greasy or wet hands. It can damage the product and lead to malfunctions. Protect the product from heavy impact. It can damage the product and lead to malfunctions. Do not place the product near a magnet, a CRT TV, or any other item emitting a strong magnetic field. It can damage the product and lead to malfunctions. Do not put anything inside the external microSD memory card slot except for the card itself. It can damage the product and lead to malfunctions. Do not operate the product with sharp instruments such as a pen or pencil. It can damage the product and lead to malfunctions. Do not attach a sticker or apply paint on the device or the microSD card. It can damage the product or microSD card and lead to malfunctions. Remove any sunshade film or any other material obstructing the view. Do not take the microSD card out during operation. It may hinder the quality of images recorded. This can damage the product and any data on the microSD card. Use approved SD memory cards only. Replace old SD memory cards. Failure to comply can lead to data loss on the SD memory card. Prolonged usage of the microSD memory card can lead to data loss. 5 Safety Warnings and Precautions Data Loss/Corruption (microSD Card Care) Damage to the microSD card can result in data corruption or loss. • microSD card is a highly sensitive piece of technology that can become defective due to changes in external environment or severe impact. Protect the card against impact and damage. • The manufacturer will not be held responsible in the event of microSD card damage due to user negligence or external factors. ※ We recommend using bulls-i models ETK - XX GB microSD cards. Causes of microSD Card Damage and Data Corruption • External impact during installation/uninstallation. • Abnormal disruption in power supply, such as sudden disconnection of the power cable while the black box is in use, can damage the microSD card. • External impact on the product while it is in operation can also cause data corruption or damage the microSD card itself. To minimize loss and damage brought on by microSD card damage regularly check and back up your data. 6 Safety Warnings and Precautions Caution Format the microSD card once a month. 기 품 확인하기 microSD Card Use 포장을 입하셨을 평한 할 장소에 바닥이나 벗겨낸 때본먼저 후 기기를 사용할 평평한 포장을 내려놓고 장소에 바닥이나 벗겨낸 본다음 기기를 사용할 평평한 내려놓고 장소에 바닥이나 본다음 기기를 사용할 내려놓고 장소에 본다음 기기를 내려놓고 다음 microSD cards have a후 service life. When the card you are using reaches the end of its service life, check the 빠져있을 card구입한 for damage replace it with부속품이 a new제품을 unit. The actual 경우 service제품을 life of a given 부속품이 속품이 있는지 야 합니다. 빠져있을 확인해 모두 만약 들어 보아야 부속품이 경우 있는지 제품을 합니다. 확인해 만약 보아야 부속품이 경우and 제품을 합니다. 빠져있을 구입한 만약 경우 빠져있을 구입한 구입한 microSD card varies depending on the actual use and care of the card. 의하여 니다. 주시기 바랍니다. microSD Card Recording Capacity Guide (Recording Quality: High) 4GB 8GB 16GB 32GB 4GB: 1 hrs to 8GB: 2 hrs to 16GB: 3 hrs 30 mins 32GB: 6 hrs 30 mins 30시거잭 mins 30시거잭 mins hrs hrs 케이블 본체 거치대 시거잭 Micro 케이블 SD1 hrs 메모리카드 거치대 Micro 케이블 SD2 hrs 메모리카드 Micro 케이블 SDto 4메모리카드 Micro SDto 7메모리카드 ※ This product has been designed as a road safety accessory. The manufacturer will not be held liable whatsoever in the event of an accident while using this product. Please use this product for intended purposes only. Recommended microSD Cards We recommend that you purchase bulls-i 8GB/16GB microSD cards from an authorized dealer. Visit케이블 www.bulls-i.co.kr and 케이블 navigate to Customer Center 8GB/16GB 명서 D 메모리카드 3M 테이브 사용설명서 3M클립 테이브 사용설명서 클립 사용설명서 케이블> Notices 클립 > bulls-i 케이블 클립microSD Card Retail Information. 리더기 (거치대 부착용) (거치대 부착용) Transcend class 10 microSD cards are also compatible. (Supports HD and SDHC) 그림은 를•수본있습니다. 실제 사용설명서의 제품과※다를 그림은 수 있습니다. 실제 다를 6수months 있습니다. microSD Card제품과 Warranty: 들은 위해 없이 •본 제품 이용자에게 변경될 제품의 성능수구성품들은 향상을 있습니다 통보 위해 없이제품 이용자에게 변경될 성능수향상을 있습니다 통보 위해 없이 이용자에게 변경될 수 있습니다 통보 없이 변경될 수 있습니다 7 7 7 77 Safety Warnings and Precautions GPS Use • If you are using the product for the first time or using it after an extended period of nonuse (3 days or longer), it will take longer than usual for the GPS to determine your current location. • GPS signal strength is susceptible to weather conditions (rain, fog, etc.) and radio wave interference. • The ideal ambient temperature range for the GPS receiver is 0℃ - 60℃/32°F -140°F. Maintain this temperature range inside the vehicle, especially during summer and winter months. • GPS reception may be low underneath an overpass, inside a tunnel, or with a high density of buildings nearby. • The GPS receiver may not function properly in vehicles with special coating or tinting on the windshield or equipped with electromagnetic wave-generating devices on board. • GPS reception may be low or unavailable altogether near high-rise buildings or power cables due to the effects of high voltage. • With poor GPS reception, it may take longer to determine the current location if the vehicle is moving. • Time and speed displays may not function properly in GPS shadow zones and under poor GPS reception conditions. 8 Main Features 200만 화소 200만 화소 2채널 카메라 2채널 카메라 전방 : 1280 전방x 720(HD) : 1280 x 720(HD) 후방 : 640후방 x 480 : 640 x 480 영상 압축 영상 : H.264 압축 : H.264 화소 Full-HD200만 Video 전방 : 1280 x 720(HD) 후방 (Full-HD) : 640 x 480 1080 ACC OFF 영상 압축 : H.264 • 1920 x • Video Compression: H.264 고감도 GPS 수신 고감도 GPS 수신 GPS Security 수신 GPS 정보를 통한 LED 수신 정보를 통한 3극 상시 전원 위치, 속도, 운행속도, 경로를 위치, 운행 경로를 Highly Sensitive GPS Google Map에 표시 Google Map에 표시 Receiver (sold sepaGPS 수신 rately) 고감도 GPS 수신 정보를 통한 위치, 속도, 운행 경로를 to • Uses incoming GPS signals Google Map에 표시 indicate the current location, speed, and route on Google Full-Touch LCD LCD Full-Touch Maps®. 2.4인치 터치 LCD를 통한 2.4인치 터치 LCD를 통한 편리한 기능 사용 기능 사용 편리한 카메라 Voice Guidance2채널 전방과 후방 동시 녹화 • Voice responses for greater ease of use. 다양한 녹화 모드 다양한 녹화 모드 상시 녹화, 수동녹화, 녹화,수동 녹화, 3 상시 Security LED 충격 녹화를 음성과 함께 충격 녹화를 음성과 함께 Wi-Fi Smartphone 동영상 저장 동영상 저장 Connectivity 다양한 녹화 모드 • View real-time video feeds, 상시 녹화, 수동 녹화, play back recordings, configure 충격 녹화를 음성과 함께 settings, receive alerts,동영상 report 저장 accidents, and GPS track using your smartphone. 즉시 재생 즉시 재생 저장 된 영상을 LCD를 저장 된 영상을 LCD를 통하여 즉시 재생,즉시 확인재생, 확인 통하여 Security LED Video Out • Security LED activation LCD ACCFull-Touch OFF in Parking2.4인치 Mode.터치 LCD를 통한 • View real-time video feeds and 즉시 재생 change the settings on저장 exter된 영상을 LCD를 nal AV devices such as통하여 a GPS 즉시 재생, 확인 navigation unit. Secur 편리한 기능 사용 Security LED 전방과 후방 동시 후방 녹화 동시 녹화 전방과 3극 상시 전원 Parking Mode 주차 감시 모드 주차 감시 모드 Battery Protection 배터리 방전 차단 배터리 방전 차단 주차 감시 모드 배터리 방전 차단 주차 중 움직임 및 움직임 충격이 주차 중 충격이 • Starts recording when및motion 녹화 경우 녹화 감지되는 or감지되는 impact경우 is detected while the (모션디텍션) (모션디텍션) vehicle is parked. 주차 중 움직임 및 충격이 감지되는 경우 녹화 (모션디텍션) • Prevents the batteries from방전 차량의 배터리 차단 방전 차단 차량의 배터리 completely discharging while in Parking Mode. 차량의 배터리 방전 차단 9 GPS GPS 수신 GPS GPS 수신 정보를 수신 수신 정보를 정보를 정보를 통한 통한 통한 통한 위치, 위치, 위치, 속도, 위치, 속도, 속도, 운행 속도, 운행 경로를 운행 운행 경로를 경로를 경로를 Google Google Google Google Map에 Map에 Map에 Map에 표시 표시 표시 표시 다양한 녹화 모드 차량에 과도한 충격이 가해지는 경우 자동 녹화 상시 녹화, 수동 녹화, 충격 녹화를 음성과 함께 동영상 저장 Main Features 3G 충격 센서 모드 다양한 다양한 녹화 녹화 모드 모드 녹화, 상시상시 녹화,녹화, 수동수동 녹화,녹화, 과 함께충격충격 녹화를 녹화를 음성과 음성과 함께함께 동영상 동영상 저장저장 3G 충격 상시 상시 녹화, 상시 상시 녹화, 녹화, 수동 녹화, 수동 녹화, 수동 수동 녹 충격 충격 녹화를 충격 충격 녹화를 녹화를 녹화를 음성과 음성과 음성 음 함 동영상 동영상 동영상 동영상 저장 저장 저장 저장 센서 3G3G 충격 충격 센서 센서 차량에 과도한 충격이 차량에 차량에 과도한 과도한 충격이 충격이 가해지는 경우 자동 녹화가해지는 가해지는 경우경우 자동자동 녹화녹화 Full-Touch Full-Touch Full-Touch Full-Touch LCD LCD LCD LCD 2.4인치 2.4인치 2.4인치 2.4인치 터치 터치 LCD를 터치 터치 LCD를 LCD를 통한 LCD를 통한 통한 통한 편리한 편리한 편리한 편리한 기능 기능 사용 기능 기능 사용 사용 사용 저장 저장 된 저장 저장 된 영상을 된 영상을 된영상을 영상을 LCD를 LC 통하여 통하여 통하여 통하여 즉시 즉시 재생, 즉시 즉시 재생, 재생 확인 재 즉시 재생 저장 된 영상을 LCD를 통하여 즉시 재생, 확인 즉시 즉시 재생 재생 기능 설정 넓은 화각 Wide Recording 120도 시야각 넓은 화각 • 140° Recording 120도Angle 시야각 사용자 필요에 의한 Angle 기능 설정 OFF 사용자ACC 필요에 의한 CD를 저장저장 된 영상을 된 영상을 LCD를 LCD를 확인 통하여 통하여 즉시즉시 재생,재생, 확인확인 기능을 바로 설정 주차 주차 주차 감시 주차 감시 감시 모드 감시 모드 모드 모드 Security LED 3극 상시 전원 주차 주차 중 주차 주차 중 움직임 중 움직임 중움직임 움직임 및및 충격이 및 충격이 및충격이 충격이 감지되는 감지되는 감지되는 감지되는 경우 경우 녹화 경우 경우 녹화 녹화 녹화 3-Axis Acceleration (모션디텍션) (모션디텍션) (모션디텍션) (모션디텍션) 배터리Shock 방전 차단 Detection 3G 충격 센서 과도한 충격이 차량의 배터리 방전 차단 차량에 충격 센서 Sensor 3G 가해지는 경우 자동 녹화 차량에 과도한 충격이 12~24V 12~24V 12~24V 12~24V 충격충격 (이벤트) 충격 충격 (이벤트) (이벤트) (이벤트) 기능 설정 녹화녹화 녹화 녹화 Event필요에 Recording 사용자 의한 기능 설정 바로 설정 Constant기능을 Power 기능 기능 설정 설정 (Triaxial) 사용자 사용자 필요에 필요에 의한의한 기능을 바로바로 설정설정 activates Parking • 기능을 Automatically Mode when ignition is shut off. 배터리 배터리 배터리 배터리 방전 방전 방전 차단 방전 차 차량의 차량의 차량의 차량의 배터리 배터리 배터리 배터리 방전 방전 차 방 microSD Formatting • Format the microSD SD card directly 포맷 제품에서 SD card를 from the bulls-i. 차단 배터리 배터리 방전 방전 차단 차단 SD card 포맷 • 차단 Shock Detector with Adjustable 가해지는 경우 자동 녹화 제품에서 SD card를 전 차단차량의 차량의 배터리 배터리 방전방전 차단 바로 포맷 Sensitivity. 전원전원 전원 DC: 12V to전원 24V 즉시 즉시 즉시 재생 즉시 재생 재생 재생 바로 포맷 SDSD card card 포맷 포맷 제품에서 제품에서 SD card를 SD card를 바로바로 포맷포맷 상시상시 상시 상시 녹화녹화 녹화 녹화 Continuous Recording 수동수동 수동 수동 녹화녹화 녹화 녹화 Manual Recording 기능을 바로 설정 사용자 필요에 의한 기능을 바로 설정 수동 녹화 o SD 통한 그레이드 micro SD 통한 업그레이드 micro micro SD 통한 SD 녹화통한 영상 업그레이드 업그레이드 순차 삭제 Upgrade via microSD Card 10 녹화 영상 순차 삭제 녹화녹화 영상영상 전자 순차순차 삭제삭제 액자 Overwriting SD card 포맷 제품에서 SD card를 SD card 포맷 바로 포맷 제품에서 SD card를 바로 포맷 전자 액자 전자전자 음성 녹음 액자액자 ON / OFF Audio Recording On/Off 음성 녹음 ON / OFF 음성음성 녹음녹음 ON /ON OFF / OFF Settings micro micro mi SDm 업그레이 업그 업 Accessories SD/MMC/RS-MMC USB 2.0 Mount Power Cable (Plug-in or Wire-in) microSD Card (adapter included) Cable Clips User Manual microSD Card Reader Use rM an ua l bulls-i Vehicle Drive Recorder Double-sided Tape • Images used in this manual may differ from the actual product. • Accessories offered by the manufacturer as part of the product package may change without prior notice. 11 Accessories Accessories (Sold Separately) Video Cable GPS ※ Available for purchase at www.bulls-i.co.kr. • Images used in this manual may differ from the actual product. 12 Wi-Fi Dongle Table of Contents Safety Warnings and Precautions Main Features Accessories Table of Contents 1. Overview 2 9 11 13 14 5. Using the Dedicated Viewer 34 5-1 Program Installation 34 5-2 Launching the Program 35 5-3 Using the Launcher 36 5-4 Dedicated Viewer 37 14 5-5 Dedicated Viewer Controls 38 1-2 Mount 17 5-6 Open File 40 2. Installation 18 5-7 Route Display (GPS) 40 2-1 Precautions 18 5-8 Miscellaneous Features 41 2-2 bulls-i Installation 19 5-9 Program Settings 42 5-10 Clock 43 1-1 bulls-i 3. Using the bulls-i Vehicle Drive Recorder 21 5-11 Time Zone Configuration 44 3-1 Recording 21 5-12 microSD Card Folders 44 3-2 Reset 24 5-13 Upgrading Firmware 45 3-3 microSD Memory Card Removal 25 4. Video Out 26 6. Product Specifications and Certifications 46 26 6-1 Product Specifications 46 28 6-2 Product Certifications 47 33 7. Troubleshooting 8. Warranty 48 49 4-1 Video Out Connection 4-2 Recording Playback and Settings 4-3 Warnings and Cautions 13 1. Overview 1-1 bulls-i 6 4 1 2 7 5 Name 8 3 Function Name Function 1 1. Camera Lens Records front-facing video. 5 5. Memory Card Slot for microSD cards. Slot 2 2. Power Jack Input for the power cable. 6 6. Wi-Fi Dongle Port Port for the Wi-Fi dongle. 3 3. GPS IN Input for the GPS cable. 7 7. Speaker (buzzer) Emits auditory signals and warnings and voice guides. 4 4. Video IN Input for the video cable. 8 8. LED Indicates the bulls-i operating status. • Images used in this manual may differ from the actual product. • Accessories offered by the manufacturer as part of the product package may change without prior notice. 14 1. Overview 1 2 3 4 5 Basic Function Video Out Function 1 Power/ Rec Power on/off (hold for 3 seconds)/Manual recording (normal press) Manual Recording 2 OK/MIC Audio recording on/off Menu mode on/off (hold) 3 CLR/SPK Speaker on/off/Wi-Fi data reset (hold for 5 seconds and select OK (yes)) Previous menu 4 UP System reset (hold for 5 seconds and select OK (yes)) Folder navigation and file selection 5 DOWN microSD card formatting (hold for 5 seconds and select OK (yes)) Folder navigation and file selection • Images used in this manual may differ from the actual product. • Accessories offered by the manufacturer as part of the product package may change without prior notice. 15 1. Overview 1 2 3 56 4 Name Function 1 Power LED Flashes during power up and stay lit when powered on 2 Event LED Turns on when event (impact), manual, and parking recording is in progress 3 GPS LED Turns on when receiving a GPS signal 4 Security LED Flashes while in Parking Mode and stays lit when recording is in progress while in Parking Mode 5 Speaker LED Turns on when the speaker is turned on. 6 MIC LED Turns on when audio recording is turned on. • Images used in this manual may differ from the actual product. • Accessories offered by the manufacturer as part of the product package may change without prior notice. 16 1. Overview 1-2 Mount 3 2 1 Name Description 1 Mount Used to attach and detach the bulls-i to the vehicle. 2 Mount Angle Adjuster Adjust the angle and tighten the screw to set in place. 3 Double-Sided Tape Used to attach the mount to the front windshield. 17 2. Installation 2-1 Precautions Parts & Accessories • Make sure you have all the parts and accessories before installing the bulls-i. ► Page 11 • If you are missing parts or accessories, contact your place of purchase. Installation The bulls-i’s position on the front windshield and its forward-facing angle greatly affect the video recording quality. Follow these instructions to get the best results: • Install the mount on the central axis of the vehicle. • Do not use the bulls-i without the mount. • Do not place any item between the bulls-i and the front windshield or cover up the bulls-i. • Secure the mount in place using the double-sided tape. However, make sure the windshield area where you will be attaching the mount to is free of dust and other forms of contaminants. 18 2. Installation 2-2 bulls-i Installation Check the installation site and have everything in place. Refer to page 2 for installation precautions. This device must be installed on the central axis of the vehicle and on the upper portion of the windshield in order to achieve optimal recording performance. 1 Clean the windshield using a clean piece of cloth. 2 Remove the protective film from the strip of double-sided tape attached to the mount. 4 Insert the microSD card all the way inside the bulls-i's microSD card slot until it clicks in. 5 Attach the bulls-i to the mount. 3 Attach the mount flush to the windshield. 19 2. Installation 6 Connect the power cable to the units PWR IN port. 7 Insert the other end of the power cable into the vehicle's power outlet. 8 Use the included cable clips to hide loose cables. • The unit generates warning messages if the microSD card is not recognized. (audio message and LED) • Contact a professional installer if you wish to use the constant power source cable. Black: GND/White: ACC/Red: BAT(B+) • If you are not using GPS, you can set the clock using the PC viewer. 20 3. Using the bulls-i Vehicle Drive Recorder 3-1 Recording 3-1-1. Powering On and Continuous Recording 1 2 3 Turn the unit on. --The blue LED will flash. Start recording. --The unit generates warning messages. (audio message and LED) The unit begins [Continuous Recording] once the LED lights up steadily. End recording. --Shut off the ignition and the unit will turn off after 10 to 20 seconds of data parsing. (Switches to Parking Mode automatically if using a constant power source.) 21 3. Using the bulls-i Vehicle Drive Recorder 3-1-2. Event Recording Recording is automatically triggered in the event of an impact detection. and Red LEDs: On/Buzzer: 2 beeps -Blue 3-1-3. Manual Recording Press the power button to start recording. and Red LEDs: On/Buzzer: 2 beeps -Blue In Event Recording, it records a total of 20 seconds per event, 5 seconds prior to the event and 15 seconds after the event. Recording time may vary depending on image quality and resolution settings. 22 Pre Recording: 5 seconds Post Recording: 15 seconds Event Occurrence 3. Using the bulls-i Vehicle Drive Recorder 3-1-4. Parking Mode Recording If connected to a constant power source, the bulls-i automatically begins recording. --Security LED: Flashes in Parking mode. --Security LED: Steadily lit while recording in Parking mode. Values configured under Settings during video out or using the Dedicated Viewer apply to Parking mode recordings. Continuous Continuous and impact recording Motion Motion and impact recording Impact Impact recording 23 3. Using the bulls-i Vehicle Drive Recorder 3-2 Reset 3-2-1. Resetting Wi-Fi Data 1. Press and hold the SPK/CLR key for 5 seconds. 2. LEDs above the OK and CLR keys light up. 3. To reset, press the OK key. If not, press the CLR key. 3-2-2. Resetting Settings 1. Press and hold the UP key for 5 seconds. 2. LEDs above the OK and CLR keys light up. 3. To reset, press the OK key. If not, press the CLR key. 3-2-3. Formatting Memory Card 1. Press and hold the DOWN key for 5 seconds. 2. LEDs above the OK and CLR keys light up. 3. To reset, press the OK key. If not, press the CLR key. 24 3. Using the bulls-i Vehicle Drive Recorder 3-3 microSD Memory Card Removal Always remove the microSD card from the slot in the following order: 1 2 Shut off the ignition and then hold the unit's power button for 3 seconds to turn it off. (Alternatively, you can unplug the power cable from the unit or the cigarette jack.) Push down on the microSD card. Once the card pops out, remove it from the slot. Removing the microSD card while the black box is turned on will cause data corruption. 25 4. Video Out 4-1 Video Out Connection Connect the video cable to a GPS navigation unit or an external AV device. 4-1-1 Booting and Recording ► 1 Once bulls-i is powered on, it will take 10 to 15 seconds for the unit to boot up. --Blue LED flashes. ► 2 Once the bulls-i finishes booting up, it will automatically enter Continuous Recording mode. (Home Screen) --Blue LED lights up steadily. Video Out is not supported in Parking mode. 26 3 Once the vehicle's ignition is turned off, it will take 10 to 15 seconds for bulls-i to save the recording file and turn off. --All LEDs turned off. 4. Video Out 4-1-2. Event Recording Live View > Event Recording Screen Event recording message will appear in the event of an impact detection while in Live View mode. and Red LEDs: On/Buzzer: 2 beeps -Blue 4-1-3. Manual Recording Press the power button to start manual recording. and Red LEDs: On/Buzzer: 2 beeps -Blue Continuous and Event (impact) recording is not supported while in menu mode. 27 4. Video Out 4-2 Recording Playback and Settings 4-2-1 Recording Playback (under development) ► Press and hold the OK key to enter the menu mode. ► Press the OK key to access the video playback menu. Continuous/Parking List of Continuous recordings Event List of Event recordings ► Select a file from the video list and press the OK key. Selected file is played on the screen. Menu mode will automatically switch over to Continuous Recording screen after 10 seconds of inactivity. Menu mode cannot be accessed while Event recording is in progress. 28 4. Video Out 4-2-2 Settings Press and hold the OK key to enter the menu mode. Press the OK key to access the settings menu. Speaker Activates/deactivates buzzer warnings and voice guides. Sound Recording Activates/deactivates audio recording via the MIC. Image Quality Specify the recording image resolution. Parking Specify the recording mode to use when parked. Impact Sensitivity Used to adjust the impact detection sensitivity. Format microSD Card Formats the microSD card. 29 4. Video Out 4-2-2-1 Functions Settings > Speaker ► ► ► Adjust the buzzer and voice guide volume. the speaker volume turns off the speaker -Muting LED. Settings > Audio Recording ► Activates/deactivates audio recording via the MIC. this option to turns on the MIC LED. -Setting 30 4. Video Out Settings > Image Quality Specify the recording image resolution. ► Full HD -1080p: HD -720p: Settings > Parking Mode Recording ► ► Parking recording is activated automatically when the ignition is turned off. There are 3 Parking modes to choose from. * Motion Detection Parking Mode: This is the default setting. Recording automatically starts when motion or change in the lighting condition is detected. * Continuous Parking Mode: Constantly records video while the vehicle is parked. * Impact Parking Mode: Recording automatically starts when impact is detected. In order to maximize the microSD card's recording capacity, we recommend you use the Motion Detection Parking mode. Settings > Impact Sensitivity ► ► Used to adjust the impact detection sensitivity. (Recommended Setting: Medium) 31 4. Video Out Settings > Foarmat SD This option formats the microSD card inserted into bulls-i. ► 1 Format: Formats the card. Cancel: Cancels formatting. ► 2 Formatting in Progress 3 Do not remove the micro SD card while formatting is in progress. 32 Once formatting is complete, bulls-i will reboot. 4. Video Out 4-3 Warnings and Cautions When a microSD card is missing or a microSD card error has occurred. When switching to a different mode. When upgrading firmware. When it's time to format the microSD card. (Once a month) Resuming recording. 33 5. Using the Dedicated Viewer 5-1 Program Installation The viewer lets you play back recorded video on a computer. ► 1 Uncompress the downloaded file and double-click "setup.exe". To download the program, visit www.bulls-i.co.kr and navigate to Downloads. 2 Designate the installation folder and click [Install]. 4 A launch icon will appear on the desktop. ► 3 34 Once the program is installed, click [Close]. • bulls-i Viewer: Viewer • bulls-i Suite: Launcher 5. Using the Dedicated Viewer 5-2 Launching the Program MC S-M C/R MM SD/ USB 2.0 ► Disk San 4GB 1 Connect microSD Card to the Computer --Insert the micro SD card into the reader and then plug in the reader to your computer’s USB port. 2 Launching the Program --Double-click on the launcher icon on the desktop. Make sure the micro SD card is right side up when inserting it into the reader. 3 Program launcher will appear on the screen. The viewer and the launcher operate in conjunction with one another. 35 5. Using the Dedicated Viewer 5-3 Using the Launcher 12 3 4 5 6 7 8 9 Name Description 1 Model Inserting the micro SD card displays the product's model name. 2 Firmware Version Inserting the microSD card displays the product's firmware version. 3 Viewer (Analysis) Program Launches the dedicated viewer. 4 Settings Launches the viewer's settings screen. 5 Firmware Download Downloads the latest firmware version. 6 Format microSD Card Lets you format the micro SD card from your computer. 7 Miscellaneous New bulls-i feature. 8 New Product Info Introduces new bulls-i products. 9 Website Link Link to the bulls-i website. 36 5. Using the Dedicated Viewer 5-4 Dedicated Viewer • In order to use Google Maps, you will need to have Internet access and Internet Explorer 7.0 or above installed on your system. • The map feature may not function properly with files that are missing GPS data due to poor signal reception at the time of their recording. • The map feature is only available when the GPS module (optional) is connected to the unit. 1 2 1 2 3 4 5 6 7 8 9 0 3 4 5 67 8 9 0 Name Description Main Panel 3-axis Sensor Sensor Readings Speedometer GPS Signal Video Progress Bar Coordinates Panel Swap Sub-Panel Map Open Displays the front camera's recording. Displays the impact sensor's axial (X, Y, and Z) readings. Displays the vehicle's speed. (GPS models only) Indicates the GPS signal reception status. (GPS models only) Indicates video playback progress. Displays lateral and longitudinal GPS coordinates. (GPS models only) Used to swap the main panel with the sub-panel. (2CH models only) Displays the rear camera's recording. (2CH models only) Indicates the vehicle's location on a map. (GPS models only) Used to select and open a file for playback. 37 5. Using the Dedicated Viewer 5-5 Dedicated Viewer Controls Name Description 1 Settings Used to configure bulls-i's settings. 2 Screenshot Captures and saves a screenshot of the video. (.png or .jpg) 3 Print Prints the current frame. 38 5. Using the Dedicated Viewer 5-5 Dedicated Viewer Controls Name Description 1 Play Plays the selected video file. 2 Pause Pauses playback. 3 Stop Stops playback. 4 Previous File Plays back the previous file. 5 Rewind 1 Frame Rewinds by 1 frame. 6 Fast Forward 1 Frame Fast forwards by 1 frame. 7 Next File Plays back the next file. 8 Zoom-In Zooms in on the video. 9 Zoom-Out Zooms out from the video. 0 1:1 Ratio Displays the video in its original ratio. ! Pan Pan while zoomed-in on a video. @ Vertical Flip Vertically flips the video. 39 5. Using the Dedicated Viewer 5-6 Open File Click on the button and select a file. 5-7 Route Display (GPS) Displays the route taken on a map using GPS data. • This feature is available with models that have the GPS module installed only. • This feature is only available with an Internet connection. 40 5. Using the Dedicated Viewer 5-8 Miscellaneous Features Full Screen: Right-clicking on the playback screen displays it in full screen mode. 41 5. Using the Dedicated Viewer 5-9 Program Settings Video/ Audio Resolution Specify the resolution you wish to use. Video Quality Adjust the video recording quality. Video Frame Rate Choose the frame rate. Sound Recording Activate/deactivate audio recording. Sound Volume Adjust the buzzer and voice guide volume. Time Setting Used to set the black box's system clock. You can retrieve and use the computer's system time settings. (Make sure the computer's time setting is correct.) DTS Setting Subtracts 1 hour from the clock during the specified period. Use if DST is in effect in your area. The clock will be adjusted automatically on the specified starting date. GMT Setting Used to select your time zone. Shock Sensitivity Adjust the impact detection sensitivity. Time Function Viewer Settings 42 Event Files Specify the number of event files to keep on the memory card. Motion Sensitivity Used to adjust the motion detection sensitivity for Parking mode. Battery Prevention Specify when you want the Battery Protection feature to be activated. Speed Unit Specify the black box's speed unit. Security LED Enable/disable security LED while parked. Language Select the viewer's display language. Speed Unit Specify the speed unit displayed on the viewer. 5. Using the Dedicated Viewer 5-10 Clock Used to set the unit's clock. Select Retrieve Time to use the computer's system clock settings. 43 5. Using the Dedicated Viewer 5-11 Time Zone Configuration Used to select your time zone. 5-12 microSD Card Folders Folder Name Description • Contains Continuous and Parking (inc. motion detection) recording files. “rec” --Continuous Recording: 1-minute files --Motion Detection Parking Mode: 20-second files/Continuous Parking: 1-minute files e.g.) Continuous: 20120412_111535_I.avi Parking: 20120412_111535_P.avi • Contains Event, Manual, and Parking Event recording files. “event” “update” 44 --Event (Impact) Recording: 20-second files (10 to 40 files by default) --Parking Event: 20-second files e.g.) Continuous Event: 20120412_111535_I.avi Parking Event: 20120412_111535_P.avi • Used for updating the firmware. • Also contains a text (.txt) file that indicates the current firmware version. 5. Using the Dedicated Viewer 5-13 Upgrading Firmware 1 Connect the microSD card to the computer. 2 Create an "update" folder on the microSD card. 3 Copy the firmware files to the "update" folder. 4 Insert the microSD card into the bulls-i and reconnect the power cable. 5 The firmware will be upgraded automatically and the bulls-i will reboot. • Do not forcibly turn off the bulls-i or remove the microSD card while firmware update is in progress. It could cause the system to malfunction. • The microSD card's file system must be set to FAT16 or FAT32. Other system formats, including NTFS, are not supported. 45 6. Product Specifications and Certifications 6-1 Product Specifications Function Camera Recording GPS Storage Audio Power Wi-Fi Miscellaneous Image Sensor Channels Recording Angle Video Compression Resolution Frame Rate Recording Modes Event Recording Sensor Event Recording Time Parking Mode Speed, Location, Google Map Default Maximum Input Output Main Power Sub Power (Internal) Smartphone Connectivity Video Playback/Settings Voice Guide Specification_ETK-B2400 2.0 megapixels 1 140° H.264 1920 X 1080 (Full-HD), 1280 X 720 (HD) 30 fps (Max) Continuous, Manual, Event, Parking 3-Axis Acceleration Shock Detection Sensor 5 seconds backwards and 15 seconds forwards (Full-HD) Motion detection and 3-Axis Acceleration Shock Detection Sensor Supported (sold separately) 16GB microSD card 32GB Built-in MIC Speaker (voice guide) DC 12V to 24V, 200mA Super Capacitor 802.11n Video Out (GPS navigation unit and external AV devices) Supported • This product’s firmware is upgradeable. Firmware updates may improve the product’s performance and are available for download at the manufacturer’s website (www.bulls-i.co.kr). • Specifications of this product are subject to change without prior notice. 46 6. Product Specifications and Certifications 6-2 Product Certifications • KCC: Broadcasting/communications device certification • CE: European certification for industrial safety and quality • FCC: U.S. Federal Communications Commission certification • RoHS: Restriction of Hazardous Substances Directive 47 7. Troubleshooting If you are having trouble with this product, please check the following troubleshooting information before requesting servicing. Contact the customer center only if the problem persists after implementing the measures described below. Problem 48 Solution Video recordings are not being saved to the microSD card. • Remove the microSD card and try inserting it again. The bulls-i is unable to read the memory card. • Format the microSD card and try again. • If the microSD card is old (expired), replace it with a new one. What happens if the microSD card becomes full? • Existing recording data are overwritten with new data, starting with the oldest. The recordings have poor picture quality. • Check to see if the protective film has been removed from the camera lens. • Check to see if the camera lens is dirty. • Check to see if the windshield is dirty or has obstacles such as dark tinting. The bulls-i is not working. • Check the power connection. • Check to see if you are using an original power cable from the manufacturer. 8. Warranty Regarding product servicing… ● In compliance with consumer compensation rules and regulations, Ether Technology Inc. offers the following warranty coverage for this product. ● If you experience a malfunction and require servicing, contact the nearest Ether Technology Inc. bulls-i product retailer. ● Visit www.bulls-i.co.kr for the bulls-I for warrenty coverage and details. Covered Malfunctions arising under normal use within the warranty period (1 year) are eligible. Warranty period for products used for commercial purposes, however, is half that of the normal warranty period (6 months). Paid Servicing 1) Non-Malfunctions Once a servicing request is made, the consumers will be charged with a servicing fee if the concerned issue is found to be a non-malfunction. It is therefore important that you read this user manual carefully before making any servicing request (limited to cases where repairing is not possible and is subject to separate standards). 2) Malfunctions due to Consumer Negligence □ Malfunctions caused by disassembly or modification of the product by the consumer at their own discretion or due to consumer negligence (submersion in water, damage, etc.). □ Malfunctions arising from repair of the product by an individual who is not a technician from Ether Technology Inc. or one of its authorized affiliates. □ Malfunctions arising from use of unauthorized parts and/or accessories. The product is □ Malfunctions arising from failure to adhere to the Safety Warnings and Precautions contained in the user manual. covered under 3) Other Circumstances warranty for a □ Malfunctions caused by natural disasters (fire, salt, water, lightening damage, etc.). period of one □ Expired parts and accessories (attachments). year. □ Use of an unstable power supply against which impulse voltage cannot offer protection. Consumer Damage Defects and malfunctions arising under normal use during the warranty period Malfunctions caused by consumer negligence Need for critical repair within 10 days of purchase Need for critical repair within 1 month of purchase Product damage that arose during transportation or installation Need for critical repair within 1 month of receiving a replacement Replacement not available Malfunction with the same root cause occurs 3 times Can be repaired Malfunctions with different root causes occur 5 times Misplacement of a product handed in by the consumer for repair purposes Repair not possible because of parts unavailability Required parts are available, but the repair cannot be performed Cannot be repaired Can be repaired Compensation During Warranty Period After Warranty Period Replacement Replacement Replacement Not applicable Replacement Refund Replacement Paid servicing Replacement Paid servicing Replacement Product replacement following deduction of Replacement depreciation value Replacement Product replacement following deduction Product replacement following deduction of paid of paid servicing fee servicing fee and depreciation value Paid servicing Paid servicing Refund: Purchase Price (must present receipt) About the Serial Number The serial number identifies individual products, and it is important that you do not misplace it. The manufacturer assumes no responsibility for any loss or damage resulting from misplacement of the serial number. Product Model Vehicle Drive Recorder ETK-B2400 Date of Purchase Place of Purchase Serial Number Price 49 ETK-B2400