Transcript
DIGITAL MODULATOR DMSD01
AV TO DVB-T ENCODER/MODULATOR
USER MANUAL
DMSD01 Congratulations on your purchase of the DMSD01 This ‘state of the art’ product, is an SD encoder. The video and audio can be taken from CVBS inputs and compressed into MPEG 2 video and AAC or MPEG1-L2 audio. The output is configured as DVB-T transport stream. Stand alone configuration is made easy through 4 tactile switches and ergonomic menu’s. To make the configuration of the DMSD01 ultra simple, a special software DMSDiface is available that you can download on our website: http://antiference.co.uk/product/conexer-dvb-t-modulators/ Please select ‘Downloads’ to commence download.
CONTENTS 1
Safety considerations
2
Description of the different elements
3 Installation and menu structure 3.1
Powering up
3.2 Menu structure 4.0
The DVB settings menu
4.1
The AV settings menu
4.2
The Video settings menu
4.3
The Audio settings menu
4.4
The TS settings menu
4.5
The Language menu
4.6
Default configuration
5
Programming using a PC
6
Technical specifications
7
Declaration of Conformity
2
DMSD01 1 SAFETY CONSIDERATIONS 1.1 Connecting to the mains supply This product has to be connected to a 12v mains supply using the supplied power adaptor. If there is the slightest doubt concerning the type of connection available on the installation, please contact your supplier of electricity. Before carrying out maintenance operation or modification of the installation, the modulator must be disconnected. Only use the power adaptor supplied. 1.2 Over Voltage An over voltage on the mains supply can cause short circuits or risk of fire. Never overload the power cables. 1.3 Liquids This product should be protected from liquid splashes and moisture. Please check that no containers containing liquids are placed on or near this item. 1.4 Cleaning Disconnect the product before cleaning. Use only a damp cloth and never use solvents. 1.5 Ventilation In order to assure an adequate air circulation and to prevent overheating, the ventilation holes should never be obstructed. The product should not be installed in a hermetically sealed environment. Other electronic products or heat producing items should not be placed on or near the product. 1.6 Accessories The use of third party accessories could cause damage to this product. Only use Antiference recommended products. 1.7 Installation of the modulator. This modulator should be installed in a place well protected from direct sunlight and moisture. Do not install near heating elements or other devices producing heat. Check that the modulator is placed at least 10 cm from any other equipment that is susceptible to electromagnetic radiation. Do not place or install the modulator on any unstable items, a fall could cause physical or material damage.
3
DMSD01 2 - Description of the different elements
RF Input
5V/2A Power supply
RF Output
USB for PC connection
Video Input
Right Audio input
Left Audio input
Cancel/Return button
Enter button
Digital Display
Backward/Up button Forward/Down button
4
DMSD01 3 - Installation and menu structure 3.1 - Installation Please find a typical connection and installation layout for the DMSD01 L
R
3.1 Powering Up Plug in the connector of the power supply. The display will show the CONEXER logo while booting. Once the modulator has booted correctly the main menu will appear. In the first line the model number is displayed (DMSD01) followed by the installed firmware version. When the modulator is in Encoding mode, the resolution is displayed at the bottom of the screen. When the modulator is Initialising mode, INIT will be displayed at the bottom of the screen
5
DMSD01 3.2 - Menu Structure The DMSD01 has different menus allowing easy access to the different parameters and to change them when necessary. Below you will find the structure of the different menus:
Menu Selection: In order to scroll from one menu to another, use the move up/down ( and ) buttons to select your required option. Press the enter ( ) button to select your choice. Press the cancel (X) button to go back to the previous menu. Menu Editing: Where available within certain menu options, you can edit values to suit your required parameters. Use the and buttons to move to the desired character and press the enter ( ) button to confirm. Please note the following special characters:
6
DMSD01 4.0 The DVB settings menu In this menu you can set the output frequency, bandwidth, output level and specific parameters for DVB-T. Select the appropriate option with the and buttons and press the enter button to confirm.
• Set the output frequency
MODE • Select the bandwidth
MODE • Set the output level
MODE • Select the mode
• Select the constellation
• Select the F.E.C
• Select the Guard Interval
7
DMSD01 4.1 The AV settings menu
• Set the video bit rate
• Select the audio bit rate
• Select the compression type
VIDEO SETTINGS
4.2 The Video settings menu You are able to edit a comprehensive range of video settings using the following sub menus.
• Set the Video resolution
• Set the compression type
• Set the video bit rate
• Set the format
8
DMSD01 VIDEO SETTINGS
4.2 The Video settings menu continued
• Set the Luminosity
• Set the Contrast
• Set the Saturation
AUDIO SETTINGS
COMPRESSION AUDIO RATE
4.3 The Audio settings menu continued You are able to edit a range of audio settings using the following sub menus.
COMPRESSION AUDIO RATE
AAC-LC MPEG1-L2
COMPRESSION AUDIO RATE
192Kb/s 256Kb/s 320Kb/s 384Kb/s
9
DMSD01 4.4 The TS settings menu • Set the NIT version
• Set the Network ID
• Set the Original Network ID
• Set the Network Name
• Set the Transport Stream ID.
• Set the Program ID.
• Set the LCN ID.
• Set the LCN number
NIT RELEASE NET ID. ORIG. NET. ID. NETWORK NAME
NIT RELEASE 27_
NIT RELEASE NET ID. ORIG. NET. ID. NETWORK NAME
NET ID. 27_
NIT RELEASE NET ID. ORIG. NET. ID. NETWORK NAME
ORIG. NET ID. 27_
NIT RELEASE NET ID. ORIG. NET. ID. NETWORK NAME
NETWORK NAME NoName
NET ID. ORIG. NET. ID. NETWORK NAME TS ID.
TS ID. 100_
ORIG. NET. ID. NETWORK NAME TS ID. PROGRAM ID.
PROGRAM ID 1_
NETWORK NAME TS ID. PROGRAM ID. LCN ID.
EACEM ITC
TS ID. PROGRAM ID. LCN ID. L.C.N.
L.C.N. 1_
PROGRAM ID. LCN ID. L.C.N. SERVICE NAME 10
SERVICE NAME Chan A_
DMSD01 4.4 The TS settings menu • Set the Programme name
• Set the Video PMT
• Set the Video PID
PROGRAM ID. LCN ID. L.C.N. SERVICE NAME
SERVICE NAME Chan A_
LCN ID. L.C.N. SERVICE NAME PMT PID
VIDEO PMT 32_
L.C.N. SERVICE NAME PMT PID VIDEO PID
VIDEO PID 48_
• Set the Audio PID
SERVICE NAME PMT PID VIDEO PID AUDIO PID
• Set the EIT Title*
PMT PID VIDEO PID AUDIO PID EIT TITLE
EIT TITLE DMSD01_
VIDEO PID AUDIO PID EIT TITLE EIT TEXT
EIT TITLE DESCRIPTION_
• Set the EIT Text*
* The EIT Title and EIT Text will pop up on the TV screen when selecting the INFO button on the TV remote control whilst watching a television programme that is being distributed through the DMSD01 Modulator.
4.5 The Language settings menu Select the chosen language of your choice
11
DMSD01 DEFAULT CONFIG.
4.6 The Default Configuration settings menu Select this to return to original Factory Settings. Please note that ALL modifications will be lost.
5 - Programming using a PC The settings of the DMSD01 can also be changed using a PC. First, please install the software DMHDiFace on your PC. You can download this software from our internet site: http://antiference.co.uk/product/conexer-dvb-t-modulators/ Please select ‘Downloads’ to commence download. After installation of this software, connect the DMSD01 using a USB cable (not included) to your personal computer. Then launch the program DMHDiFace. On the display of the DMSD01 the message ‘USB’ appears, indicating that the programming is now performed through your PC. All parameters previously explained in section 4 manually programmed on the modulator can now be modified and edited on a PC using the DMSDiFace software.
12
DMSD01 6 - Technical Specifications
Video input
Audio input
DVB Processing
DVB-T output
Power
Dimensions
Input
RCA
Resolution modes
PAL-SECAM
Compression
H.264 – / MPEG2-SD / MPEG2 - bitrate 5-15 Mb/s
Input
RCA
Compression
AAC-LC / MPEG1-L2 - bitrate 128-384 Kb/s
Table insertion
PAT, PMT, SDT, NIT, EIT
Configuration
Channel / network name, SID, LCN, TSID, ONID, NID, versions, audio, video PIDs...
Output frequency / level
170-230 MHz + 470-862 MHz / > 80 dBμV
Constellation - FEC
QPSK/16QAM/64QAM - 1/2, 2/3, 3/4, 5/6, 7/8
Guard interval
1/4, 1/8, 1/16, 1/32
Mode - MER
2K/8K - 31 dB
DC 2.1 mm connector
+5V
Consumption
10 Watts
LxWxH
170x130x35mm
Weight
0.6kg
7 - Declaration of Conformity: We, ANTIFERENCE LIMITED herewith declare that the modulator CONEXER DMSD01 complies with all essential requirements and any other applicable conditions set forth on directive 1999/05/CE. According to the WEEE (Waste Electrical and Electronic Equipment) EU Directive, do not dispose of this product as household waste or commercial waste. Waste electrical and electronic equipment should be appropriately collected and recycled as required by practices established for your country. For information on recycling of this product, please contact your local authorities, your household waste disposal service or the shop where you purchased the product. Date of issue: April 2017
13
DMSD01
14
DMSD01
15
www.antiference.co.uk
