Transcript
USER MANUAL Table of Contents
Safety Information……………………………………...………………3 Specifications………………………………………...…………………4 Main Power Connection…………………………...…………………..6 DMX-512 Connection……………………………..…………………...6 Rigging the Fixture……………………………….…………………….7 Main Control Menu……………..…………………………………..….7 DMX Profile...................................................................................10 Cleaning & Maintenance...............................................................14 Parts List.......................................................................................14
Check that the unit has not been damaged during transport
Protection Against Fire 1. 3. 4. 5. 6.
Maintain a minimum of 1 foot distance from any type of flame. Replace fuse only with the specified type and rating. Do Not install the unit to close to a heat source. Make sure cable are properly secured away from unit movement. Maximum surface operating temperature 104º.
Protection Against Fire 1. 2. 3. 4.
Disconnect power before lamp replacement or servicing. For connection to main power supply proceed to page 6. This unit must be earthed. (electronically grounded) Do not expose unit to rain or moisture.
Protection Against Mechanical Hazards 1. Use safety chain when hanging unit. 2. Use quality clamps or bolts when positioning unit 3. Do not open unit risk of electrical shock.
3
Specifications Part Numbers Fixture
Lamp
Flight Case
1130 - AXIS 7D5
LLUM75 –75W LED
P-1130
DUALCASE
Mechanical Specifications Pan:
540°
Tilt: 270°
DMX Connectors:
3-pin and 5-pin XLR connectors
Thermal:
Maximum ambient temperature 100° F Maximum surface temperature 130° F
Fastening System:
2 Treaded M8 mounting positions
14 3/8 ”
12.75 ”
13.65 ”
Fixture
Packaged for Shipping
Size: 13.10” x 9” x 17.75” Weight: 21.5 lb
13.30 ”
Size: 21.25” x 17.25” x 11.75” Weight: 24 lb
4.10 ”
9”
Electrical Specifications Power supply:
Auto Switch100V-240V 50/60 HZ
Power consumption:
Amps Watts
Ballast:
Electronic
LAMP:
75 Watt LED
1.20 144
Electromechanical Effects Focus:
Motorized Focus
Prism:
3-Facet prism rotating in both directions at different speeds
Dimmer:
Electronic Lamp Dimmer.
Shutter:
Electronic Lamp strobe of lamp 18 flash per second
Color:
8+Open bi-directional rotation
Gobo:
7+Open bi-directional rotation
4
13.10 ” ( with handles )
Color 1: Open 2: Red 3: Orange 4: Green 5: Light Blue 6: Purple 7: Yellow 8: Blue 9: Pink
Gobo’s Rotating Gobo Wheel
1: Open
2: Gobo 1 3: Gobo 2 4: Gobo 3 5: Gobo 4 6: Gobo 5 7: Gobo 6 8: Gobo 7
(note) Gobo’s on the Axis 7D5 are not removable
Prism Rotating 3 way Prism
5
Main Power Connection Caution! 1. 2. 3.
Do not connect fixture to a dimmer system. This unit must be earthed. (electronically grounded) Replace fuse only with the specified type and rating.
This device is equipped with a auto switching power supply that will allow you to work from 100V-240V 50/60Hz The occupation of the connection-cable is as follows: Cable (USA)
Cable (EU)
Pin
110V
220V
Black
Brown
Live
L
L
White
Light Blue
Neutral
N
L
Green
Yellow/Green
Ground 220V Connec-
L
L
N
L
110V Connec-
DMX-512 Connection The fixture is equipped with 3 pin and 5 pin XLR Sockets for DMX input and output. The sockets are wired in parallel. Only use a shielded twisted pair cable designed for RS-485 and 3 pin or 5 pin XLR plugs and connectors in order to connect the controller with the fixture or the fixture with another.
DMX—output
DMX—input 1. Shield 2. Signal (-) 1
2
5
1
4
2 3
3
3. Signal (+) 4. N/A
1
2
1
5
2
4 3
3
5. N/A
Caution!
At the last fixture the DMX signal needs to be terminated with a terminator. Solder a 120 Ohm resistor between the (-) and the (+) signal into a 3 pin or 5 pin XLR plug and plug it in to the last fixture on the signal run. Pre-manufactured terminator plugs are available for purchase from your Mega-Lite dealer (P-DMX-T). 6
Rigging the fixture Caution! 1. The installations must be carried out by an authorized dealer or trained professional. 2. Unit may cause severe injures if you have doubts concerning the safety do not install. 3. Unit is to be 24inches away from flammable materials (decoration material) 4. Use high quality installation equipment to hang unit.
When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experience including but not limited to calculating working loads, material being used and periodic safety inspections. If you lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger. When rigging the unit always be secured with a secondary safety attachment. The installation location of the projector has got to be built in the way that it can hold 10 times the weight for 1 hour with out any harming. Installation should be checked at least one time a year by a skilled person.
Main Control
DMX
The control board on the fixture base is your interface to access and control all the functions on the unit. Its LED display gives you a code view of the options and functions. The following will explain each function and its options.
ERR ▲ MENU
Introduction Resetting
Setup Menu Press the ▲ and then press the Enter button to Access the setup menu
001 Set
Manu
Sys
Advan
►Setting Run Mode DMX Address Channel Mode Invert Pan Invert Tilt Swap Pan-Tilt Encoder Pan-Tilt No DMX Signal Display Power Save Load Default
DMX 001 15CH OFF OFF OFF ON KEEP OFF
Run Mode DMX Address Channel Mode Invert Pan Invert Tilt Swap Pan-Tilt Encoder Pan-Tilt No DMX Signal Display Power Save Load Default
DMX 001 15CH OFF OFF OFF ON KEEP OFF ►
Run Mode DMX Sound Random F-Sleep 8 F-Stand 8 Draw Up 8 Auto 1 thru 4
Will operate using a DMX controller The light will activate it’s built in programs with sound activation The preprograms will be activated randomly Slow large figure 8 movement program Slow small figure 8 movement program Figure 8 movement in the up position Built in programs
DMX Address Press Enter use the ▲ or ▼ to select the desired DMX start Channel. Press Enter to confirm the setting .
7
▼
UP DOWN ENTER
Run Mode DMX Address Channel Mode Invert Pan Invert Tilt Swap Pan-Tilt Encoder Pan-Tilt No DMX Signal Display Power Save Load Default
DMX 001 15CH OFF OFF OFF ON KEEP OFF ►
Channel Mode
Run Mode DMX Address Channel Mode Invert Pan Invert Tilt Swap Pan-Tilt Encoder Pan-Tilt No DMX Signal Display Power Save Load Default
DMX 001 15CH OFF OFF OFF ON KEEP OFF ►
Invert Pan
Run Mode DMX Address Channel Mode Invert Pan Invert Tilt Swap Pan-Tilt Encoder Pan-Tilt No DMX Signal Display Power Save Load Default
DMX 001 15CH OFF OFF OFF ON KEEP OFF ►
Invert Tilt
Run Mode DMX Address Channel Mode Invert Pan Invert Tilt Swap Pan-Tilt Encoder Pan-Tilt No DMX Signal Display Power Save Load Default
DMX 001 15CH OFF OFF OFF ON KEEP OFF ►
Swap Pan-Tilt
Run Mode DMX Address Channel Mode Invert Pan Invert Tilt Swap Pan-Tilt Encoder Pan-Tilt No DMX Signal Display Power Save Load Default
DMX 001 15CH OFF OFF OFF ON KEEP OFF ►
Encoder Pan-Tilt
Run Mode DMX Address Channel Mode Invert Pan Invert Tilt Swap Pan-Tilt Encoder Pan-Tilt No DMX Signal Display Power Save Load Default
DMX 001 15CH OFF OFF OFF ON KEEP OFF ►
No DMX Signal
Run Mode DMX Address Channel Mode Invert Pan Invert Tilt Swap Pan-Tilt Encoder Pan-Tilt No DMX Signal Display Power Save Load Default
DMX 001 15CH OFF OFF OFF ON KEEP OFF ►
Display Power Save
Run Mode DMX Address Channel Mode Invert Pan Invert Tilt Swap Pan-Tilt Encoder Pan-Tilt No DMX Signal Display Power Save Load Default
DMX 001 15CH OFF OFF OFF ON KEEP OFF ►
Load Default
This function allows you to select what operating mode you would like to use 15CH or 19CH. Press Enter use the ▲ or ▼ to select the desired DMX profile mode. Press Enter to confirm the setting .
This function allows you to invert the Pan via display command. Press Enter use the ▲ or ▼ to select pan rotation configuration. Press Enter to confirm the setting .
This function allows you to invert the Tilt via display command. Press Enter use the ▲ or ▼ to select Tilt rotation configuration. Press Enter to confirm the setting .
This function will Swap the Pan Tilt channel on DMX control via display command. Press Enter use the ▲ or ▼ to select Swap the DMC channels for the Pan & Tilt Press Enter to confirm the setting . CH 1&2 Pan CH 3&4 Tilt =OFF CH 1&2 Tilt CH 3&4 Pan =ON
This function will allow you to enable or disable the encoders for the Pan and Tilt. Press Enter use the ▲ or ▼ to select ON or OFF Press Enter to confirm the setting . (note) encoders are electronics that will reposition the unit if it manually moved.
If DMX signal is removed or terminated the fixture will keep the last command or it will clear the command and place the fixture at 0 on all channels. Press Enter use the ▲ or ▼ to select KEEP or CLEAR Press Enter to confirm the setting .
This command will allow you to select to leave the display permanently on when the fixture is on, or it will let you turn off the display after 30 seconds of no pressing the buttons. Press Enter use the ▲ or ▼ to select OFF or ON Press Enter to confirm the setting .
This command will allow you to restore the fixture display commands to the factory setting . Press Enter to access the command and press Enter to reset and Menu to cancel.
8
Manual Control Press the ▲ or ▼to select the Manu then press the Enter button to Access the manual control functions
001 Set
Manu
Sys
►Manual 1. Pan 2. Pan Fine 3. Tilt 4. Tilt Fine 5. Pan-Tilt Time 6. Stop/Strobe 7. Dimmer 8. Color 9. Gobo Change 10. Gobo Rotation 11. Focus 12. Prism Insertion 13. Prism Rotation 14. Macro Function 15. Reset 16. Colour2 17. Color Time 18. DimPriFrost Time 19. Gobo Time
Advan
255 000 000 000 000 000 000 000 000 000 000 000 000 000 000
Manual Control Channels This feature allows you to access all the functions of the light. Press Enter use the ▲ or ▼ to select the function press Enter use the ▲ or ▼ to select the value that you would like to set that function press Enter to confirm. (note Ch16 –19 only available on 19 Ch mode)
Systems Report Press the ▲ or ▼to select the Sys then press the Enter button to see the system report of the fixture.
001 Set
Manu
Sys
►System Firmware DMX Monitor System Errors Total Fixture Hours Partial Fixture Hours
Advan
XUCM9A107 ► ► 00035:00 00005:58
System Firmware DMX Monitor System Error Total Fixture Hours Partial Fixture Hours
XUC-M9 A 107 Will give you a value look at what each channel is doing Will report any system error in code view Total amount of time the fixture has been powered on Total amount of time the LED has been powered on
Advance Factory authorized access only
001 Set
Manu
Sys
Advan
9
Axis 7D5 15 Ch Mode DMX Channel 1 2 3 4 5
Function Pan Pan Fine Tilt Tilt Fine Pan/Tilt Speed
6
Shutter
7
Dimmer
8
Color
9
Gobo
Description Pan Course Pan Fine Tilt Course Tilt fine Pan Tilt Speed (Slow to Fast) Closed Strobe (slow to fast) Open Dimmer off to full Open White+Red Red Red+Orange Orange Orange+Green Green Green+Light Blue Light Blue Light Blue+Purple Purple Purple+Yellow Yellow Yellow+Blue Blue Blue+Pink Pink Pink+White Color Scroll (Slow to Fast) Open Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Gobo 7
Value 0-255 0-255 0-255 0-255 0-255 0-3 4-251 252-255 0-255 0-4 5-9 10-14 15-19 20-24 25-29 30-34 35-39 40-44 45-49 50-54 55-59 60-64 65-69 70-74 75-79 80-84 85-89 90-255 0-4 5-9 10-14 15-19 20-24 25-29 30-34 35-39
Counter Clockwise Gobo scroll (Fast to Slow) Open Clockwise Gobo scroll (Slow to Fast) Gobo 1 Shake (Slow to Fast) Gobo 2 Shake (Slow to Fast) Gobo 3 Shake (Slow to Fast) Gobo 4 Shake (Slow to Fast) Gobo 5 Shake (Slow to Fast) Gobo 6 Shake (Slow to Fast) Gobo 7 Shake (Slow to Fast)
40-129 130-134 135-220 221-225 226-230 231-235 236-240 241-245 246-250 251-255
10
10
Gobo Rotation
11 12
Focus Prism
13
Prism Rotation
14
Macros
15
Control
Gobo Rotation Counter Clockwise Gobo Rotation (Fast to Slow) Clockwise Gobo Rotation (Slow to Fast) Gobo Shake (Slow to Fast) Focus No Function Prism Engage Prism Rotation Prism Shake (Fast to Slow) Prism Rotation Counter Clockwise (Fast to Slow) Prism Rotation Clockwise (Slow to Fast) No Function Macros No Function Motor Function Reset (hold for 5 seconds) Pan Tilt Reset (hold for 5 seconds) All Reset (hold for 5 seconds)
0-63 64-127 128-191 192-255 0-255 0-127 128-255 1-63 64-127 128-191 192-255 0-5 5-255 0-25 26-76 44-127 128-255
Axis 7D5 19 Ch Mode DMX Channel Function 1 Pan 2 Pan Fine 3 Tilt 4 Tilt Fine 5 Pan/Tilt Speed 6
Shutter
7
Dimmer
8
Color
Description Pan Course Pan Fine Tilt Course Tilt fine Pan Tilt Speed (Slow to Fast) Closed Strobe (slow to fast) Open Dimmer off to full Open White+Red Red Red+Orange Orange Orange+Green Green Green+Light Blue Light Blue Light Blue+Purple Purple Purple+Yellow Yellow Yellow+Blue Blue Blue+Pink Pink Pink+White Color Scroll (Slow to Fast) 11
Value 0-255 0-255 0-255 0-255 0-255 0-3 4-251 252-255 0-255 0-4 5-9 10-14 15-19 20-24 25-29 30-34 35-39 40-44 45-49 50-54 55-59 60-64 65-69 70-74 75-79 80-84 85-89 90-255
9
Gobo
10
Gobo Rotation
11 12
Focus Prism
13
Prism Rotation
14
Macros
15
Control
16
Color Effect
Open Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Gobo 7 Counter Clockwise Gobo scroll (Fast to Slow) Open Clockwise Gobo scroll (Fast to Slow) Gobo 1 Shake Gobo 2 Shake Gobo 3 Shake Gobo 4 Shake Gobo 5 Shake Gobo 6 Shake Gobo 7 Shake Gobo Rotation Counter Clockwise Gobo Rotation (Fast to Slow) Clockwise Gobo Rotation (Slow to Fast) Gobo Shake (Slow to Fast) Focus No Function Prism Engage Prism Rotation Prism Shake (Fast to Slow) Prism Rotation Counter Clockwise (Fast to Slow) Prism Rotation Clockwise (Slow to Fast) No Function Macros No Function Motor Function Reset (hold for 5 seconds) Pan Tilt Reset (hold for 5 seconds) All Reset (hold for 5 seconds) Open White+Red Red Red+Orange Orange Orange+Green Green Green+Light Blue Light Blue Light Blue+Purple Purple Purple+Yellow
12
0-4 5-9 10-14 15-19 20-24 25-29 30-34 35-39 40-129 130-134 135-220 221-225 226-230 231-235 236-240 241-245 246-250 251-255 0-63 64-127 128-191 192-255 0-255 0-127 128-255 1-63 64-127 128-191 192-255 0-5 5-255 0-25 26-76 44-127 128-255 0-4 5-9 10-14 15-19 20-24 25-29 30-34 35-39 40-44 45-49 50-54 55-59
16
Color Effect
17 18 19
Color Speed Dim/Pri Speed Gobo Speed
Yellow Yellow+Blue Blue Blue+Pink Pink Pink+White White Red Orange Green Light Blue Purple Yellow Blue Pink White Color Wheel Rotation Speed (Fast to Slow) Dimmer / Prism Speed (Fast to Slow) Gobo Wheel Speed (Fast to Slow)
13
60-64 65-69 70-74 75-79 80-84 85-89 90-94 95-114 115-134 135-154 155-174 175-194 195-214 215-234 235-254 255 0-255 0-255 0-255
Cleaning and maintenance Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installations and electronics checked by an expert every 2 years. The following points have to be considered during the inspection: 1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded. 2) There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing). 3) Mechanically moved parts like axles and other must not show any traces of wearing and must not rotate with unbalances. 4) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments. Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed. Disconnect from mains before starting maintenance operation!
Caution Danger to life!
We recommend a frequent cleaning of the device. Please use a moist, lint free cloth. Never use alcohol or solvents! 1) The objective lens will require periodic cleaning on usage and environment. Environment with foggers will require more periodic cleaning as fog fluid tends to build up residues, reducing the light output. 2) The cooling-fans should be cleaned monthly. DO NOT blow high pressure air into fans as incorrect rotation can damage the fans operation. 3) The gobos, dichroic color filters and internal lenses may be cleaned with soft brush using soapy water. 4) The interior of the fixture should be cleaned using a vacuum. 5) We recommend proper lubrication of the motor wheel. The quantity of the oil must not be excessive in order to avoid oil run outs when motor wheel rotates Note: There is no serviceable parts inside the device except for the fuse. Maintenance and service operations are to be carried out by authorized dealers. Replacing the fuse: Only replace the fuse with the same type and rating. Replacing the power cable: If the power cable of this device becomes damaged, it has to be replaced by authorized dealers only Should you have further questions , please contact your dealer.
Parts List P-1130
Dual Axis 7D5 Case
1130-PL
Primary Lens
L-HL75
HL-75W LED
1130-ARMB
Arm Body Set
1130-LD
Lamp Driver
1130-DISB
Display Body Set
1130-DIS
Display Card
1130-HEADB
Head Body Set
1130-FAN
Fan
1130-MC
Color Motor
1130-PS
Power Supply
1130MRG
Rotating Gobo Motor
1130-QRM
Quick Release Mount Set
1130-MGR
Gobo Rotator Motor
1130-FU
Replacement Fuse
1130-MF
Focus Motor
14
Warranty Information Warranty Conditions -Unless otherwise stated in writing, your product is covered by a one year parts and labor limited warranty. -LEDs are not guaranteed to match in color temperature or output. -It is the owner’s responsibility to furnish receipts or invoices for verification of purchase, date, and reseller or distributor. If purchase date cannot be provided, date of manufacture will be used to determine warranty period. -Goods returned under warranty must follow the proper authorization procedure and must be accompanied by a copy of the original invoice. -Goods repaired under warranty will be returned to the owner with the freight prepaid by MSI via the most economical means of shipment. -Repair or replacement as provided for under this warranty is the exclusive remedy of the consumer. MEGA SYSTEMS INC. makes no warranties, express or implied, with respect to any product, and Mega Systems specifically disclaims any warranty of merchantability or fitness for a particular purpose. Mega Systems shall not be liable for any indirect, incidental or consequential damage, including lost profit, sustained or incurred in connection with any product or caused by product defect or the partial or total failure of any product regardless of the form of action, weather in contract, tort (including negligence), strict liability or otherwise, and weather or not such damage was foreseen or unforeseen. - Warranty is void if the product is misused, damaged, modified in any way, or for unauthorized repairs or parts. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Mega-Lite 5718 Kenwick St San Antonio, TX 78238 Ph 210-684-2600 Fax 210-855-6279 www.mega-lite.com /
[email protected]
