Transcript
QㆍCAM TRUCK Wireless
QㆍCAM TRUCK Wireless Installation Manual
Wireless Rear View Camera
QㆍCAM TRUCK Wireless
Table of contents 1. Components 2. Specifications 3. Block Diagram 4. Instructions before operating 5. Cautions 6. Warning 7. How to install 8. Installation diagram 9. Location of rear view camera installation 10. Installation 11. Trouble shootings
● ● ● ●
●
Thank you for purchasing a Q-CAM TRUCK WIRELESS. Read manual carefully before operating. It provides instructions on safe installation, use and maintenance. Store the manual where it is easily accessible for future reference. All features and functions of products, specifications of other products and information on the manual subject to change without notice. Wireless connection can be temporarily disconnected under the influence of external environment.
1 Wireless Rear View Camera
QㆍCAM TRUCK Wireless
1. Components After purchasing a product, please check and identify the supplied components. If something is missing, contact where you purchased the product. Designs and specifications of the products are subject to change without prior notice.
OPTION Installation Manual
Cable tie
L-Type bracket (x4)
Adhesive tape (x4)
Toggle Switch
QCAM TRUCK TX
QCAM TRUCK RX
2 Wireless Rear View Camera
Camera
Bracket Allen wrench and bolts
5m Camera extension cable
8Inch Monitor
QㆍCAM TRUCK Wireless
2. Specifications Transmitter
Camera
Receiver
Effective pixels
NTSC : (H)768x(V)494 PAL : (H)752x(V)582
Frequency
2.4 GHz, 20 Channel Frequency Hopping Method
Angle of view
120˚
Image input
NTSC, VGA
IR LED
8PCS of 850mn IR , CDS Sensor 1EA (Approximately 10m visible)
Power consumption
~165mA (+12V DC) ~130mA (+12V DC) /~90mA (+24V DC) /~80mA (+24V DC)
Image sensor
NEXTCHIP Image Signal Processor NVP2080 (PELICAN-S)
Operating voltage
+12V ~ +24V DC
Operating voltage
12V (On:170mA/Off:120mA) ~ 24V (On:80mA/Off:60mA)
Communication distance
Over 100m (Open area)
Operating Temp./Humi.
-20℃ ~ 60℃ 85%RH, Non-Condensing
Video compression
MPEG4
Waterproof
IP 69K
Frame
30 Frame
3 Wireless Rear View Camera
QㆍCAM TRUCK Wireless
3. Block Diagram Monitor
Camera
Analog Image
Analog Image
Transmitter
Receiver
Image Conversion (Analog → Digital)
Image Conversion (Digital → Analog)
Image Compression
Image Extraction
MPEG4
Wireless Module
4 Wireless Rear View Camera
2.4GHz
WIRELESS
COMMUNICATION
MPEG4
Wireless Module
QㆍCAM TRUCK Wireless
4. Instructions before operating 1. This product is a device to assist safe driving and shows images of rear camera through wireless connection when the gear is shifted into reverse. 2. This product can be connected to monitors or navigations to show images of rear camera. 3. Depends on the performance of monitors or navigations, images of reverse camera can be delayed When shifting into reverse. This kind of situation is not relevant to QDIS’S product quality. 4. As a wireless transmitter/receiver, there is no guarantee that interference will not occur by other wireless devices. 5. Images of rear camera may not display under certain environmental or operating situation. 6. It is required to drill some holes for wire connection. Please use caution when drilling holes. Otherwise, it may cause leaks. The limited warranty does not cover damage or failure caused by leaks. 7. This manual is subject to change without notice. 8. Copyright 2015 all rights reserved by QDIS. 9. The synchronization of transmitter and receiver is completed before releasing Q-CAM TRUCK Wireless. 10. Power of this product is 12V~24V and it is a free voltage product (A function of Tube voltage prevention is includedProtect the product from overvoltage).
5 Wireless Rear View Camera
QㆍCAM TRUCK Wireless
5. Cautions 1. Do not leave or use the product in direct sunlight or in a car heated by sunshine. 2. Do not bend or deform the product. 3. Do not disassemble or damage the product. 4. In case of using old or low picture quality monitors or navigations, picture quality may not be good. This kind of situation is not relevant to QDIS’S product quality. 5. In case of changing the location of rear camera, remember to adjust the camera angle before operating. 6. Connect cables as indicated on instructions when installing the product. Especially, make sure to connect a power cable and a video cable correctly. 7. Constantly check the surface of camera angle and keep it clean. 8. Do not expose to high humidity. Also, if the product is exposed to liquid, it may damage the product and it may not be repaired. 9. Use the product in temperatures between -20°C~+80°C, if possible. Exposing the product to extremely low or high temperatures may result in damage and malfunction. 10. Only use genuine products and accessories specified by the manufacturer. The company holds no liabilities for the damage to the product or accident caused by using other companies’ product or accessories.
6 Wireless Rear View Camera
QㆍCAM TRUCK Wireless
6. Warning Read all instructions before use. For your safety, the information in this manual must be followed to prevent from any risks. The company holds no liability for accidents or events caused by not following the instructions in the manual. 1. Do not use the damaged cable to reduce the risk of fire or electronic shock. 2. Leaks or improper connections may cause the risk of fire. Make sure that all the products are properly installed before turning on the product. 3. Do not excessively bend or pull on the power cable in order to reduce the risk of fire or electronic shock. 4. Do not handle the product with wet hands while connecting/disconnecting power cables in order to reduce the risk of electronic shock. 5. Do not use the product while driving. It may cause car accidents. 6. Do not install the product near any heat sources in order to prevent the risk of fire or electronic shock. 7. Do not deform or cut power cables. It may cause the damage to products and vehicles. Also, the risk of fire and electronic shock will be increased. 8. Install the product in a place where it doesn’t block driver’s view. 9. In case of not using it for long period, disconnect power cables from the product. All steps of installation should be done by well-trained specialists. Otherwise, it may cause the damage to products and vehicles. 10. The company holds no liability for damages caused by a person who is not expert.
7 Wireless Rear View Camera
QㆍCAM TRUCK Wireless
7. How to install (Turn off the device before the installation) 1. Find a place to install a camera.
2. Find a place to install a bracket.
3. Tighten screws to fix the bracket .
4. Install the rear camera on the bracket and check the camera angle.
8 QㆍCAMRear Wireless TRUCK View Wireless Camera
QㆍCAM TRUCK Wireless
7. How to install (Turn off the device before the installation) 5. The completion of the rear camera installation.
6. Find a place to install a transmitter.
7. Remove foreign materials on the surface.
8. Attach double-sided adhesive tape at the bottom of a transmitter.
9 Wireless Rear View Camera
QㆍCAM TRUCK Wireless
7. How to install (Turn off the device before the installation) Performance of transmitters and receivers is affected by certain conditions such as the directions of two devices and the surrounding environment between them. When locating the place for two devices, avoid the place where it is surrounded by metal resources in order to maximize the reception. 9. Attach the transmitter on the surface. Top surface of transmitter should face the receiver and place two devices as close as possible.
10. Tighten screws to fix L-type brackets .
11. Fix the transmitter on the surface by using cable ties.
12. Fill gaps between the transmitter and the surface with a silicone sealant.
10 QㆍCAMRear Wireless TRUCK View Wireless Camera
QㆍCAM TRUCK Wireless
7. How to install (Turn off the device before the installation) In case of connecting to a rear lamp cable, the rear image will be displayed when shifting into reverse. In case of connecting to a ACC cable, the rear image will be displayed while driving. However, we recommend to connect the transmitter power cable to the rear lamp cable considering the situation when it is required to pair the transmitter and the receiver. Otherwise, it is difficult to turn on and off the transmitter in case of pairing. 13. Detach a rear lamp connector.
14. Strip rear lamp & ground wires.
15. Connect transmitter cables to the rear lamp& ground wires respectively.
16. Attach the rear lamp connector.
11 Wireless Rear View Camera
QㆍCAM TRUCK Wireless
7. How to install (Turn off the device before the installation) 17. Organize Transmitter/Rear camera cables.
12 QㆍCAMRear Wireless TRUCK View Wireless Camera
18. The completion of the rear camera and the transmitter.
QㆍCAM TRUCK Wireless
7. How to install (Turn off the device before the installation) 19. Attach double-sided adhesive tape at the bottom of a receiver.
20. Rotate the receiver within 180 degree to find the position where the reception bars shows more than 3 bars on the monitor.
※Check the status of wireless connection displayed by the antenna bar at the top left corner of the monitor. Also, rotate the receiver within 180˚ in order to search for the best wireless connection condition between the transmitter and the receiver before attaching the receiver to the dashboard firmly.
13 Wireless Rear View Camera
QㆍCAM TRUCK Wireless
7. How to install (Turn off the device before the installation) 21. Dismantle a fuse box.
22. Attach the receiver ground cable to the surface.
23. Find the ‘cigarette lighter’ fuse on the list.
24. Detach the fuse and wrap power wires.
hter rette lig a ig c A F31 10
14 Wireless Rear View Camera
QㆍCAM TRUCK Wireless
7. How to install (Turn off the device before the installation) ※Rotate the receiver within 180 degree to find the position where the reception bars shows more than 3 bars on the monitor. 25. Reconnect the fuse.
26. Connect the extension cable to AV port of a Monitor.
27. Link the extension cable to the receiver RCA cable.
28. Check whether the rear image displays when shifting into reverse.
15 Wireless Rear View Camera
QㆍCAM TRUCK Wireless
8. How to pair Transmitter and Receiver Caution : Pairing between the transmitter and the receiver is already completed before they are released. Please refrain from doing this task except special occasion. 1. Turn off the transmitter. Connect toggle switch to the receiver pairing connector. (※ it is possible to use a double-pole switch instead of the toggle switch.) 2. Turn on the monitor and the receiver. The monitor will show the following message for 2 seconds. “No video signal” 3. Before the message disappears, press the toggle switch for more than 5 seconds. Then, the monitor will show the new message of “Please Press Pair Key on Tx Side”. Also, it will start counting down from 30. 4. Remove the hand from the toggle switch. Moreover, turn on the transmitter and wait for pairing before it counts down to 0. 5. The monitor shows the rear camera image after it shows “Wait signal… Pair OK” message. Finally, pairing is complete.
16 Wireless Rear View Camera
QㆍCAM TRUCK Wireless
9. Installation Diagram - Refrigerated truck (Use of Camera extension cable – Option)
Camera Monitor Video Connection Receiver
Fuse Box
Transmitter
Rear lamp
※This is an installation guide. Find the best position where to install the transmitter & the receiver in order to get least 3 reception bars when installing the device. Wireless Rear View Camera
17
QㆍCAM TRUCK Wireless
9. Installation Diagram - Cargo Truck ※ If the cable is not long enough to connect camera and transmitter, we recommend that you should purchase the 5 meter long c amera extension cable – Option.
Monitor Video Connection Receiver
Fuse Box
Transmitter
Camera Rear lamp
※This is an installation guide. Find the best position where to install the transmitter & the receiver in order
18
to get least 3 reception bars when installing the device.
Wireless Rear View Camera
QㆍCAM TRUCK Wireless
10. Location of Rear View Camera installation The location would be varied depends on the car model. If there is any space to install the camera, user can install it anywhere.
1. Rear view camera on the top
2. Rear view camera in the middle
3. Rear view camera on the bottom
QㆍCAM QㆍCAM
TRUCK
Cement Mixer, BCT, Agricultural truck and etc.
Cargo truck, Flatbed truck, Truck tractor and etc.
TRUCK
QㆍCAM TRUCK
Refrigerated Truck, Catering truck, Tank truck, pump truck and etc.
※This is an installation guide. Find the best position where to install the transmitter & the receiver in order to get least 3 reception bars when installing the device. Wireless Rear View Camera
19
QㆍCAM TRUCK Wireless
11. Installation
Transmitter
Receiver
20 Wireless Rear View Camera
QㆍCAM TRUCK Wireless
11. Installation – Wing body / Refrigerated truck
Camera Receiver Monitor
GND
ACC
GND Rear lamp
Transmitter
※This is an installation guide. Find the best position where to install the transmitter & the receiver in order to get least 3 reception bars when installing the device. Wireless Rear View Camera
21
QㆍCAM TRUCK Wireless
11. Installation – Tank lorry truck Camera
Receiver Monitor
GND
ACC
GND Rear lamp
Transmitter
※This is an installation guide. Find the best position where to install the transmitter & the receiver in order
22
to get least 3 reception bars when installing the device.
Wireless Rear View Camera
QㆍCAM TRUCK Wireless
11. Installation – Mixer truck
Camera Receiver
Transmitter Monitor
GND
ACC GND Rear lamp
※This is an installation guide. Find the best position where to install the transmitter & the receiver in order to get least 3 reception bars when installing the device. Wireless Rear View Camera
23
QㆍCAM TRUCK Wireless
11. Installation – Bulk cement trailer
Receiver Monitor
GND
Camera
ACC
Transmitter
GND
24
Rear lamp
※This is an installation guide. Find the best position where to install the transmitter & the receiver in order to get least 3 reception bars when installing the device.
Wireless Rear View Camera
QㆍCAM TRUCK Wireless
11. Installation – Trailer
Receiver Monitor
GND
ACC
Transmitter Camera GND
Rear lamp
※This is an installation guide. Find the best position where to install the transmitter & the receiver in order to get least 3 reception bars when installing the device. Wireless Rear View Camera
25
QㆍCAM TRUCK Wireless
11. Installation – Dump truck
Receiver Monitor
GND
ACC
Transmitter Camera
Rear lamp GND
26
※This is an installation guide. Find the best position where to install the transmitter & the receiver in order to get least 3 reception bars when installing the device.
Wireless Rear View Camera
QㆍCAM TRUCK Wireless
11. Installation – Cargo truck
Receiver Monitor
GND
ACC
Transmitter
Camera GND
Rear lamp
※This is an installation guide. Find the best position where to install the transmitter & the receiver in order to get least 3 reception bars when installing the device. Wireless Rear View Camera
27
QㆍCAM TRUCK Wireless
12. Trouble shootings Q: No image displays after the message of ‘No Video Signal’. A: Check if the receiver is properly connected to the power. Check if the cables between the monitor and the receiver are properly linked. Q: No image displays after the message of ‘Wait Signal’. A: Check if the transmitter is properly connected to a ACC power or a rear lamp. Check the status of wireless connection displayed by the antenna bar at the top left corner of the monitor. When installing the devices, it should display least 3 reception bars on the monitor. Also, rotate the receiver within 180˚ in order to search for the best wireless connection between the transmitter and the receiver before attaching the receiver to the dashboard firmly. In addition, remove any obstacles that may influence on the wireless connection or install the transmitter/the receiver in other place where there are no obstacles Q: When the picture is distorted. A: Make sure that cable connections between the camera and the transmitter are correctly linked or replace the cable. Make sure that cable connections between the monitor and the receiver are correctly linked or replace the cable. Q: No image displays even though the antenna bar at the top left corner of the monitor is showing 3~4 antennas. A: Check the cable connections between the camera and the transmitter. Check if the camera power cable connection is properly installed. Q: When the transmitter and the receiver are not paired. A: Pairing is already completed when the devices are released from the factory. Except the special occasion, please refrain from pairing the transmitter to the receiver manually. However, when two devices are not paired due to changing the rear trailer, please refer to the above instruction “How to pair transmitter/receiver.”
28 Wireless Rear View Camera
QㆍCAM TRUCK Wireless Wireless Rear View Camera
