User's Manual Facia Plate Scosche Si2227b For Suzuki Grand Vitara (044)361-05-06 Icq:495-089-192

Transcript

(044)361-05-06 ICQ:495-089-192 (067)469-02-12 ICQ:613-211-859 (099)048-99-03 (093)672-77-76 User's Manual Facia Plate Scosche SI2227B for Suzuki Grand Vitara In the online store Winauto you also can buy Facia Plate Scosche SI2227B Suzuki Grand Vitara. Delivery in Kyiv and throughout Ukraine with payment upon receipt! winauto.ua Sale - Car Receivers - Facia Plates - Head Units - Car TVs and Monitors - Antennas - Car Audio - DVR - GPS Navigation - Trip Computers - Car Alarm Systems - Mechanical Locking - Parking Systems - Car Cameras - Xenon and Lights - Established Optics - Tuning - Car Heating and Cooling Sound Marine and Electronics - Car Accessories - Isolation - Installation Components - Batteries, Power - Oils and Fluids - POCKET ASSEMBLY 6193 KIT PANEL a to .u FACTORY METAL BRACKET IN-DASH INSTALLATION KIT FOR SI2227B 6194 POCKET 2006-UP SUZUKI GRAND VITARA 6193 KIT PANEL INTRODUCTION / PRELIMINARY CAUTION: DISCONNECT YOUR VEHICLE'S NEGATIVE BATTERY TERMINAL BEFORE THE INSTALLATION TO HELP PREVENT ELECTRICAL DAMAGE. WE RECOMMEND THE USE OF A VOLT/ OHM METER OVER A TEST LIGHT TO CHECK WIRING. A TEST LIGHT OR GROUNDED WIRE PROBE CAN CAUSE DAMAGE TO THE VEHICLE'S COMPUTER AND/OR DIAGNOSTIC SYSTEMS. AVOID ALL FACTORY AIR BAG WIRING - AIR BAGS CAN ACCIDENTALLY DEPLOY CAUSING SERIOUS INJURY OR DEATH. Thank you for purchasing the Scosche SI2227B Kit. This kit was manufactured with the highest of quality standards. in au ATTACHING THE TRIM RING: Press the pocket into the lower position of the mount opening. There are (4) hole mounting locations to mount. Use supplied screws from installation kit. 6194 POCKET NOTE: REAR SUPPORT AVAILABLE SEPARATELY. REAR SUPPORTING THE RADIO ADDS TO THE INSTALLATION’S STRUCTURAL INTEGRITY. MOUNTING THE RADIO MOUNTING THE RADIO FOR SINGLE DIN OR DOUBLE DIN: A. Mount the aftermarket DIN radio to the factory metal mounting brackets using top holes with the factory hardware. B. For Double din aftermarket radio align factory brackets to double din holes, two top hole and one bottom hole should be usable. Align radio mounting assembly to the kit panel trim ring. C. Secure the whole panel assembly to the dash using screws used to secure the factory radio. ASSEMBLED 6193 PANEL 6193 PANEL STEREO INSTALLATION 1. Using a panel removal tool, remove the trim on both sides of radio and A/C control. This piece extends from side of shifter up to side of AC vents above stereo. 2. Remove the (6) Phillips Screws holding the radio and climate control. Disconnect and remove. 3. Remove (3) screws on each side of radio. 4. Remove (2) Phillips Screws holding A/C control to radio. 2 © 2007 SCOSCHE INDUSTRIES, INC. SI03B SI -04/07 - SI2227B (3000003) If you have any further questions, call our toll free technical help line at: 1-800-621-3695x3 This instruction booklet is based on carefully documented data and research of automobile dash disassembly, wire harness/codes and information pertaining to installation of this kit (SI2227B) in 2006-UP Suzuki Grand Vitara Vehicles. Scosche Industries, Inc. can not be held responsible for discrepancies/inconsistencies that may occur due to the automobile manufacturing changes or options, or damage that may occur in the automobile during the installation of components while using this booklet. LIABILITY DISCLAIMER SI03B 1996-UP Suzuki Harness PROVIDE EASY CONNECTION OF YOUR CAR STEREO TO FACTORY WIRING HARNESS. CAR STEREO CONNECTORS FACTORY WIRING CODES • Read all instructions accompanying your car stereo/cassette player for proper wiring and mounting instructions. NOTES: • See your vehicle's instructions for any special tools your installation might require. w Интернет-магазин автозвука и автотоваров Винавто