Transcript
Vehicle Security System
Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED
Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces Avoid mounting components or routing wires near moving parts Tape or loom wires under hood for protection and appearance Use grommets when routing wires through metal surfaces Use a voltmeter for testing and verifying circuits
Technical Support For Authorized Dealers - (800) 421-3209 Hours: 8:00 a.m. - 7:00 p.m. EST Monday thru Friday 10:00 a.m. - 2:00 p.m. EST Saturday This device complies with part 15 of the FCC rules and with RSS-210 of the industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Y10 / Y11 INS0883 Rev. A 11/98
System Layout
RED SIREN OR HORN OUTPUT (-)
FUSED +12V SOURCE
BLACK
ORANGE PARKING LIGHT OUTPUT (+) ILL. ENTRY / ARMED OUTPUT (-) (Y-11 ONLY)
ORANGE/BLACK VIOLET
STARTER KEY STARTER MOTOR TRUNK RELEASE (-) (Y-11 ONLY) +12 VOLTS CHASSIS GROUND (-) LOCK / (+) UNLOCK (-) UNLOCK / (+) LOCK
WHITE RED WHITE TAN RED BLACK BLUE/BLACK GREEN/BLACK
SHOCK SENSOR
WHITE YELLOW GREEN GRAY
POSITIVE DOOR TRIGGER NEGATIVE DOOR TRIGGER NEGATIVE HOOD/TRUNK TRIGGER BLACK
BLUE BROWN
RED
BROWN STATUS INDICATOR
Module Identification: 7 Tab Connectors = Y-11 6 Tab Connectors = Y-10
+12 VOLTS
DISARM BUTTON SWITCHED POWER
Refer to Wire Color / Location Chart for specific wire color, location, and polarity information. 2
1. Installation A. Siren / Horn (ORANGE on 3-Pin Connector) Make appropriate connections below. Siren • Mount bell housing downwards. • Use at least two (2) screws to secure siren to mounting location. • Connect siren BLACK wire to module ORANGE wire. • Connect siren RED wire to a fused +12-volt source. Horn Circuit verification Negative Systems - Target wire will register ground when horn is pressed. Positive Systems - Target wire registers voltage when horn is pressed. Connection Horn
Positive
Negative
Wire Relay Diagram 1
Connect to target wire. Diagram 1
Fused +12V
Module ORANGE wire
Horn
B. 12V+ Main Feed (RED) • Connect to vehicle battery or to main 12-volt lead at ignition switch harness. Circuit Verification - Target wire registers voltage at all times. C. 12V+ Switched Feed (BLUE on 7-Pin Connector) • Connect to switched 12-volt lead at ignition switch harness. Circuit Verification - Target wire registers voltage when ignition key is turned to the ON position and START position. D. Ground (BLACK) • Attach to grounded metal point of vehicle chassis. Note: When installing multiple components (such as an alarm and remote starter), ground the units separately. 3
1. Installation E. Starter Interrupt • WHITE/RED -Starter Key Side • WHITE - Starter Motor Side • Connect to vehicle starter wire at ignition switch harness. Circuit Verification - Target wire registers voltage only when ignition key is turned to the START position. Circuit Verification after starter wire is cut: • KEY SIDE of starter wire registers voltage when ignition key is turned to the START position. • MOTOR SIDE of starter wire registers no voltage. F. Door Pin Switches (YELLOW or WHITE on 7-Pin Connector) Connect appropriate module wire to vehicle target wire. (See diagram 2 below.) Circuit Verification - Refer to Vehicle Wire Color and Location Chart for circuit type and location, or verify the vehicle wire using the following guideline: • Positive Systems - Target wire registers voltage when any door is opened. • Negative Systems - Target wire registers ground when any door is opened. G. Illuminated Entry (VIOLET on 3-Pin Connector) (Y-11 Only) • Circuit Verification - Target wire is usually the door pin switch wire. Refer to section F for verification guideline. • Add a relay and connect as shown below: Door System - Relay Needed
Diagram 2
H. Trunk / Hatch Release (TAN) (Y-11 Only) • Circuit Verification - Refer to Vehicle Wire Color and Location Chart for circuit type and location, or verify the vehicle wire using the following guideline: • Positive Systems - Target wire registers voltage when the trunk / hatch is opened using the vehicle button. • Negative Systems - Target wire registers ground when the trunk / hatch is opened using the vehicle button. Connection Trunk Release 4
Positive
Negative
Wire Relay Diagram 3
Connect to target wire.
1. Installation Diagram 3
I. Parking Lights (ORANGE/BLACK Wire on 3-Pin Connector) • Circuit Verification - Refer to Vehicle Wire Color and Location Chart for circuit type and location, or verify the vehicle wire using the following guideline: • Positive Systems - Target wire registers voltage when parking lights are on. • Negative Systems - Target wire registers ground when parking lights are on. Connections Parking Lights
Positive System Connect to Target wire
Parking Light System - Relay Needed
Negative System • Add relay (dia. 4) Diagram 4
J. Hood / Trunk Pin Switch (GREEN Wire on 7-Pin Connector) • Circuit Verification - Refer to Vehicle Wire Color and Location Chart for circuit location, or install a pin switch and connect to the module GREEN wire. K. Power Door Locks • BLUE/BLACK: (-)Lock, (+)Unlock • GREEN/BLACK: (-)Unlock, (+)Lock • Circuit Verification - Refer to Vehicle Wire Color and Location Chart for circuit type and location. 5
1. Installation Connections
Type 1
Door Locks
Dia. 5
Type 2 Dia. 6
Type 3 Dia. 7
Type 4 Dia. 8
Type 5 Dia. 9
Other See specifications in Vehicle Wire Color / Location Guide or call Technical Support
Diagram 5 GREEN/BLACK - LOCK (+) BLUE/BLACK - UNLOCK (+)
Type 1 - Positive 3-Wire Door Lock System
Diagram 6 BLUE/BLACK - LOCK(-) GREEN/BLACK - UNLOCK(-)
Type 2 - Positive 5-Wire Door Lock System Diagram 7 BLUE/BLACK - LOCK (-) GREEN/BLACK - UNLOCK (-)
6
Type 3 - Negative 3-Wire Door Lock System
1. Installation K. Power Door Locks (cont.) Diagram 8
BLUE/BLACK - LOCK(-) Module Wires GREEN/BLACK - UNLOCK(-)
Factory Vacuum Pump
Cut Here
Type 4 - Vacuum Door Lock System Note: Turning on option 8, the Long Locks feature, in programmable options is required with this type of locks.
Resistors
Diagram 9
BLUE/BLACK - LOCK(-) Module Wires GREEN/BLACK - UNLOCK(-)
If door lock system requires (+), connect to 12V+. If system requires (-), connect to Ground. Vehicle Door Lock Switch or Plunger
20A
12V+ To Control Relays
Type 5 - Multiplex Door Lock System L. Status Indicator (GRAY Wire on 7-Pin Connector) • Locate a visible location on the dash with 11/2” clearance. • Drill 1/4” hole and snap the status indicator in place. • Connect the status indicator BLACK wire to the module GRAY wire. • Connect the status indicator RED wire to a fused +12-volt source.
7
1. Installation M. Shock Sensor (Optional on some systems) • Using supplied tie wrap, mount the shock sensor to the steering column or a sturdy brace or wire harness. • Plug the impact detector onto the 4-pin module connector. Note: Some shock sensors may already be attached to the harness.
N. Override/Programming Button The override/programming button must be installed for all installations • Find a suitable mounting location for the override/programming button. The selected mounting location should be as difficult as possible for an unauthorized person to find. It is recommended that the override button be mounted in different location in each installation. • Drill a 9/32 hole mounting hole in the selected mounting location and mount as shown. • Connect one of the override button wires to the module brown wire. • Connect the remaining override / programming button wire to a solid chassis ground.
2. System Power-Up • Check all connections and wire routing. • Turn ignition to the ON position. • Replace the 20-amp fuse in the module RED wire. • Turn the ignition off. 8
Programming Remote Transmitters Note: The Y-11 has four “slots”, or memory locations, to store remote transmitter codes, giving it the ability to operate from up to four remote transmitters. The Y-10 has two slots. For proper operation, a transmitter code must be stored into each memory slot. When using less than four transmitters, follow the suggested programming parameters: • One Remote Transmitter - Program four (4) times for the Y-11 or two (2) times for the Y-10. • Two Remote Transmitters - Program each transmitter two (2) times for the Y-11 or once (1) for the Y-10. • Three Remote Transmitters - Program one transmitter twice, and each remaining transmitter once. (Y-11 only) 1. Open the driver’s door and leave open. 2. If not already on, turn the ignition key to the “RUN” position. 3. Press and hold the programming button. In 15 seconds the system will chirp the siren. 4. Release the override/programming button. The system is now in the transmitter learn mode. 5. Wait five (5) seconds. 6. Press ARM button on the first transmitter. The system will chirp the siren to indicate that this transmitter code has been learned. 7. Repeat step 6 for transmitter #2 (programming each transmitter twice). 8. Turn the ignition key off to exit the learn mode. 9. Close all doors to reset the system operation.
9
3. Programming Selectable Options Note: You can go into option programming mode without exiting the transmitter learn mode. To do so, do not turn the ignition key off or close the doors at the end of the transmitter programming section and proceed directly to step 2 below. 1. Enter the transmitter programming mode as indicated above. 2. Press and release the programming button one time. The siren will chirp three (3) times to indicate the system is in the option programming mode. 3. Press the ARM button one time to select option #1. The siren will chirp one time. Pressing the disarm button on a programmed transmitter toggles the selected option’s state on or off. The status indicator (LED) will display the state of the selected option. Pressing the ARM button on a programmed transmitter selects the next option. The siren will emit a number of short chirps corresponding to the selected option number. Pressing ARM and DISARM buttons at the same time will reset all options to their factory preset states. The siren will chirp and the door locks will cycle once to indicate that the options have been reset to their factory preset programming. 4. When all options are set as desired, turn the ignition key off to exit the options programming mode. 5. Close all doors to reset the system operation.
Button 1 Press to Advance to Next Option Press BOTH Buttons (1 and 2) to Reset all Options to Factory Settings
Button 2 Press to Turn Option ON or OFF
Status Indicator Displays Option Status (ON or OFF)
Number of Siren Chirps Indicate Option Number
Status Indicator
Y-11
Y-10
Option Number and Description Bold Type Indicates Factory Settings 1 Siren chirps when arming and disarming 2 System arms automatically 60 seconds after last door is closed 3 (1) Siren output enable (2) Horn output enable 4 Doors lock when ignition is turned on 5 Doors unlock when ignition is turned off 6 Double unlock pulse enable 7 Armed out put enable 8 Door lock / unlock output duration is (1)1/2 second or (2) 6 seconds * Siren output is the default on the Y-11, Horn is the default on the Y-10
10
ON
YES YES (1) YES YES YES YES (2)
OFF NO NO
(2)* NO NO
NO NO (1)
Testing the Alarm System Arming and Disarming Close all doors and press ARM on remote transmitter. Press Disarm on remote transmitter.
• All doors lock • Siren chirps two times / parking lights flash • Status indicator flashes steadily • All doors unlock • Siren Chirps once / parking lights flash • Status indicator turns off
Alarm Triggering / Starter Interrupt / Trip ID / Lock Options Arm system. Wait 10 seconds, then • Siren sounds / parking lights flash open door. With siren sounding, attempt to • Vehicle will not start start vehicle. Wait until siren stops, then press DISARM • Siren chirps / parking lights flash 4 times on transmitter. (System was triggered) (Y-11 only) Press Override button. • Siren chirps two times (System was triggered by door) (Y-11 only) Close doors and attempt to start vehicle. • Vehicle starts • Doors lock (if Ignition Lock Option is activated) (Y-11 only) Turn ignition off. • Doors unlock (if Ignition Unlock Option is activated) (Y-11 only) Panic Press both buttons
• Siren sounds / parking lights flash for 30 seconds.
Passive Arming (Test only if Passive Option is activated) Enter vehicle and close doors. Turn Ignition • Alarm arms one minute after door is closed on for 5 seconds, then, turn off. Exit vehicle and close doors. Valet Enter Vehicle With system disarmed, turn ignition on, then press ARM. Turn ignition off. With system in valet mode, turn ignition on then press DISARM
• Status Indicator emits a double-blink pattern. (Enters valet mode) • Status Indicator will continue to emit double-blink pattern. • Status indicator turns off (Valet mode is exited)
Antenna Placement Keep the antenna as straight as possible, and route away from vehicle harnesses.
11
12
