Transcript
V-Station™ Fingerprint
Authentication Reader
Quick Start Instructions Required items for Setup / Installation:
This Quick Start Guide – Included A V-Station unit with mounting plate – Included CD containing application software, Installation and Operation Manuals – Included Security hex key needed to reveal the RJ-12 Aux port - Included An RJ-12 to DB-9 cable for programming the unit through the Aux port – Included DC power supply at 12-24V (UL-listed class II 12V @ 500mA recommended) – Not supplied
Optional items for Setup / Installation:
Networking cable, Wiegand door controller, and Proximity Cards – Not Supplied RS-232/RS-485 Converter – Not Supplied External Wiegand Reader using a supported format – Not Supplied Computer running Windows 98, ME, NT 4.0, 2000, or XP – Not Supplied PC Ethernet NIC card and Ethernet cable (straight thru patch cable if connecting to a switch or hub, or a cross-over cable if connecting directly to the PC Ethernet card) – Not Supplied*
Getting Started Before installation please do the following:
Read both the Operations and Installation Manual (Documents included on the CD-ROM) Read the V-Station Operator’s Manual for instructions on using the V-Station from the keypad Install the VeriAdmin Software on a PC/Laptop. Configure Veri-Series units with correct baud rate, unique Network IDs, and IP address (if using Ethernet*) Become familiar with the V-Station operation, especially enrolling users using either the keypad or the PC software Read the “Veri-Series CHANGES.pdf” file on the CD for the latest updates.
NOTE 1: CAUTION: The silicon sensor used in the Veri-Series product line is an electro-static sensitive device. The EGND connection on the back of the V-Station must be connected to an earth ground for reliable operation. Installing a unit without proper grounding will void the warranty. Refer to the installation manual for specific information. NOTE 2: The V-Station differs from other Veri-Series products in that the pigtail wiring bundle in the back of the unit has been replaced by Weidmuller connections and RJ-11/RJ-45 jacks. RS-232 communication is achieved by plugging into the labeled RJ-11 jack while the RJ-45 jack provides RS-485 communication. Note that there is also a physical switch which enables the RS-485 jack. V-Stations are shipped with this switch in the default position of “OFF” and must be switched to “ON” if RS-485 communication is desired. All ports including the AUX port on the bottom of the unit are set to a baud rate of 57600 from the factory.
430-00120-01
Setting Up the V-Station
Install the VeriAdmin Software (included on CD) on a computer running Windows 98, ME, NT 4.0, 2000, or XP to initially set up the V-Smart. You can install the template management software on your computer by running “Setup.exe” found on the CD.
Apply power to the V-Station through either the DC jack (12V DC) or the Weidmuller connectors in the back: connect DC power (12-24 V) to the +(POS) terminal, and the power return (power ground) to the –(NEG) terminal.
Connect the programming cable to the Aux port in the bottom of the unit.
Run / Open the VeriAdmin software on your PC. Indicate which PC ports you would like to use, either COMM ports or Ethernet* (or both).
Now add units to the logical network tree diagram one at a time assigning unique network IDs. After establishing communication and setting up your network, you may enroll or delete templates, broadcast them to other units, store them on the PC, and configure each reader as desired.
Please refer to the Veri-Series Operations Guide for complete user instructions.
Additional Information The biggest difference between the V-Station and the other Veri-Series products is obviously its keyboard and LCD screen. The product can be configured directly from the keypad and feedback is provided on-screen. Most operations which had to be performed from the PC using VeriAdmin can now be done directly from the keypad. Some of these functions include: 9 9 9 9
Template management (enroll, edit, and delete) System control (time, date, transaction log, etc) Security (biometrics, global threshold, etc) Communications (ports, baud rates, network ID, Wiegand settings, etc)
Not all functionality can be accessed via the keypad. Future firmware versions will add additional functionality but some things will still need to be done via the PC, such as transferring templates to additional units, reading the transaction log, etc.
Technical Support Contact Information: Telephone:
866.304.7180 (toll free) 818.304.7180
Email:
[email protected]
Address:
Bioscrypt, Inc Technical Support Dept 5805 Sepulveda Blvd, Suite 750 Van Nuys, CA, 91411
*Ethernet is supported in version 7.10 and later 430-00120-01
