Transcript
V28R Installation Housing Setup Guide
Unpack Everything Check that the following items are included in your box: - MagnaView V28R enclosure - Hardware kit - V28 Series Gimbal - V28R Installation Gimbal Setup Guide - Product Warranty card - Mounting template - Lens package (option)
Important Safeguards Installation and servicing should be done by certified technicians to conform to all local codes and to maintain your warranty.
Installation Conduit Plug CAUTION
To minimize moisture leaking into the MagnaView V28R housing, position the enclosure with the conduit ponting down.Apply an appropriate sealant around the conduit connection.
Your MagnaView V28R camera enclosure comes with a conduit plug pre-installed in the ½”conduit entry on the back.This plug may be removed and installed in the side 3/4” conduit entry (see Figure 1).
Figure 1 Conduit Plug Installation Back View
Side View Retainer Plate
Captive Screw
Gasket
Conduit Plug Installation
Conduit Plug
Mounting Guide 1. 2.
Affix the mounting template (supplied) to the mounting surface (see Figure 2). Pre-drill four holes as indicated on the template, using the recommended hole size for the screws being used. 3. Drill out conduit hole, if required. Note Alternate fasteners (preferably stainless steel) can be used, provided they are not larger than a #12 screw.
-1-
Figure 2 Mounting Template Guide
Mount Wall ended m recomis way th
nting Mou te V28 pla Tem
Wiring Options Warning!
The use of a CSA Certified/UL Listed Class 2 power adapter is required to ensure compliance with electrical safety standards.
Your MagnaView camera is supplied with one of the three different termination PC boards mounted to the bottom of the housing.All connections are made here. See Figure 3 for the wiring option you have selected.
Figure 3 Wiring Options UTP Termination Board
+-
+Video
+++Audio Power
Video Audio
Power Not used Case/Ground
Not used Case/Ground
Fiber Termination Board with ST Connector
- + Power
Case/Ground
-2 -
+-
Coax Termination Board
Wiring Connections You can connect your coaxial, UTP, or fiber video cable directly to the termination board.You can also connect the coaxial cable to the mini coax BNC pigtail (supplied). Note
For direct connections to the termination board, it is recommended that you route the cable using the cable clamp supplied to restrain the cable (see Figure 4).
Figure 4 Video Cable Connection
Termination board
Cable Guidelines Note
Metric conversions are approximate.
Maximum Power Supply Cable Length (feet/meters) Cameras With AC/DC Power Supplies Total load 2.5 W 2.5 W 3.5 W 3.5 W
Power supply 15 VDC 24 VAC 15 VDC 24 VAC
24 AWG 260/79 608/185 60/18 470/143
22 AWG 415/126 980/299 100/30 760/232
18 AWG 1055/321 2515/767 250/76 1926/587
16 AWG 1680/512 3930/1198 400/122 3065/934
Note Calculations are based on an unregulated linear power supply, which would be worse case. Using a regulated or switching power supply can increase the cable distance. Silent Witness recommends using a CSA Certified/UL listed Class 2 power adapter to ensure compliance with electrical safety standards.
Maximum Video Coaxial Cable Length (feet/meters) RG-59 RG-6 Cable type 23 AWG* 18 AWG* Wire gauge 750/229 1500/457 Max length * Copper clad steel core, 95% braided shield -3-
RG-11 16 AWG* 2000/610
Specifications Application: Mounting: Cable entry: Construction: Base/Cover Dome Finish: Dimensions: Weight: Ratings:
Indoor/outdoor Ceiling/wall 3/4” (side of base) / 1/2”(bottom of base) Cast aluminum alloy Hard coated polycarbonate White urethane powder paint 6.1” (w) x 3.8” (h) (154.94 mm x 96.52 mm) 3.0 lbs (1.36 kg) UL 2044, UL 50 NEMA 4X IP66X FCC, CE
This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.
RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
This symbol indicates that important operating and maintenance instructions accompany this unit.
-4-
Regulatory Notices FCC Statement (U.S.A.) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Industry Canada Notice This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur la matériel brouilleur du Canada. Œ The Œ mark on the product indicates that the system has been tested to, and conforms with, the provisions noted within the 89/336/EEC Electromagnetic Compatibility Directive.
Warranty and Service Subject to the terms and conditions listed on the Product Warranty Card, during the warranty period, Silent Witness will repair or replace, at its sole option, free of charge, any defective products returned prepaid. In the event you have a problem with any Silent Witness product, please call the Service Department for assistance or to request a Return Authorization (RA) number. In the U.S.A. and Canada, call 1.800.893.9513 Or call +1.604.574.1523. Be sure to have the model number, serial number, and the nature of the problem outlined for the technical service representative. Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped to Silent Witness without a clearly identified Return Authorization (RA) number may be refused.
-5-
MagnaView Series Model No Format Example: V28 R C B21 XXX
029, 036, 060, 080, 120, 160,AV1,AV2, VPI Lens Type: Camera Type (EIA/NTSC): B1= B/W Std, B6= B/W High Res, C1= Color Std, C6= Color High Res (CCIR/PAL)): B21= B/W Std, B26=B/W High Res, C21= Color Std, C26= Color High Res E1=Color Std EXview (NTSC), E21 = Color Std EXview (PAL) C= Coaxial interface,T= UTP interface, F= Fiber Optic Interface* Interface: R= Round, S=Square, C=Corner Mount Case Type: V28 MagnaView Series Model No. *V28R only
AV1 = 4-8 mm Auto Iris AV2 = 2.6-5.6 mm Auto Iris VP1 = 2.9, 6, 8 mm Fixed Lens
Cameras in the V28 MagnaView Series: MagnaView V28R MagnaView V28S MagnaView V28C Accessories Available: V28R-PK Pendant (Accessory to V28R) V28R-WK Wallmount (Accessory to V28R) V28C-TC Top Cap (Accessory to V28C)
www.silentwitness.com
Sales: Tech Service: Phone: Fax: Email:
6554 - 176th Street 1.888.289.2288 Surrey, BC V3S 4G5 1.800. 893.9513 CANADA 1.604.574.1526 1.604.574.7736
[email protected] Document 920.0116 REV 4.00 Specifications subject to change without notice.
MagnaView and Advanced Surveillance™ are trademarks, and Silent Witness® is a registered trademark of Silent Witness Enterprises Ltd. © 2002 Silent Witness Enterprises Ltd.All rights reserved. Printed in Canada.
