Transcript
Rev. 122013
INTERFACING SOLUTIONS
RVCFD-79
REAR-VIEW INTEGRATION INTERFACE FOR FORD VEHICLES w/ MyFord Touch RADIOS We recommend reading this installation guide first before starting any INSTALLATION OVERVIEW work. Following these instructions from “Start” to” Finish” will ensure a smooth and hassle free installation. We offer telephone support M-F 9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help. DOES NOT REQUIRE DOES YOU TO NOT REQUIRE YOU TO FACTORY PARTSTOINCLUDED:
(2) FD-79DISPLAY Interfaces 54-PIN (1) FD-79 T-Harness (female plug) (1) 15ft Extension Cable -----------------------------------(1) Instruction ------------------
FORD: 2011 - 2014 2011 - 2014 2012 - 2014 2013 - 2014 2013 - 2014 2013 - 2014 2013 - 2014 2013 - 2014 2013 - 2014 2013 - 2014 2013 - 2013 2013 - 2014 2013 - 2014 2013 - 2014
TAPTO FOR REVERSE SIGNAL TAP FOR REVERSE SIGNAL FACTORY (SIGNAL (SIGNAL IS FROM MODULE) DISPLAYIS FROM MODULE) 54-PIN
54-PIN
(male plug)
(female plug)
-----------------------------------------------------
Edge Explorer Focus Focus ST Taurus Escape F150 F150 Raptor F250, 350, 450, 550 Fusion Hybrid Fusion Energy Taurus C-Max Hybrid C-Max Energy
LINCOLN: 2011 - 2012 MKX 2013 - 2014 MKS 2012 - 2014 MKT
WORKS FOR ALL: MyFord Touch Radios
- Remove the negative side of the battery to avoid any short circuits 12V installation.OPTIONAL/ 12V OPTIONAL/ durring the TOGGLE SWITCH TOGGLE SWITCH NOT INCLUDED NOT INCLUDED FUSE FUSE - Do not install the interface near any major components or near the 15 FT. (NOT INCLUDED) (NOT INCLUDED) HVAC system. This may cause damage or overheating to the vehicle. TOEXTENTION FRONT END
C-500
WHITE/ OPTIONAL 12V OUTPUT
INTERFACE INTERFACE Please read the entire manual before installing this interface. GROUND This interface does not activate DVD reader. ON
ON
INSTALLING THE INTERFACE: 1
2
3
4
5
6
1
BLACK/
8-PIN
2
3
4
5
ON 1
ON
8-PIN
2
3
4
5
(male plug)
6
1
C-125
2
3
4
5
6
C-500
RED/ CAMERA POWER
WHITE/ REVERSE 12V OUTPUT
YELLOW RCA/ VIDEO SIGNALCAMERA
3. Connect both interfaces to the T-Harness provided. 4. Remove the 54-Pin connector from behind the display. 6. Make the T-Harness connections behind the factory display, and turn the key to the “ON” position. 5. On the C-125 module only, set Dip 2 to ON and wait for the display to reset, this may take up to 1 minute. 7. Connect the RED power wire from the camera to the WHITE wire on the C-125 module only. The C-500 module’s White wire is strictly a 12v Accessory Output wire, not a Reverse trigger. 8. Test the back-up camera before re-installing the dash assembly.
CAMERA RCA
(SIGNAL IS FROM MODULE)
54-PIN
(female plug)
ON 1
2
3
4
5
54-PIN
(male plug)
8-PIN
CAMERA
(male plug)
6
RED/ CAMERA POWER
RED BARREL/ 12V CAM POWER
4-PIN BARREL CONNECT FOR CAMERA POWER AND SIGNAL
C-125
INTERFACE 12V
WHITE/ REVERSE 12V OUTPUT
FUSE (NOT INCLUDED)
OPTIONAL/ TOGGLE SWITCH NOT INCLUDED
ON 1
C-500
2
3
4
5
6
GREEN/ 12V POWER SWITCH (SAME FUNCTION AS DIP 1) NON-PERMANENT
WHITE/ OPTIONAL 12V OUTPUT
INTERFACE
ON DEACTIVATING THE RVC CODING
ON 1
(male plug)
3
4
5
6
C-125
WHITE WIRES CONNECT TO INVERT IMAGE
GREEN WIRES CONNECT TO ACTIVATE GRID LINES
WHITE/BLACK/ REVERSE 12V OUTPUT GROUND SCREW HOLES
8-PIN
(male plug)
8-PIN
2
15 FT.
EXTENTION TO FRONT END OF THE CAR
8-PIN
1 2 3 4 5 6 1. Remove the factory display to gain access to the C-125 module. 2. Turn the key to the “ON” position. 3. On the C-125 module only, set Dip 2 to OFF and wait for the display C-125 to reset, this may take up to 1 minute. INTERFACE
“SET TO OFF, WITH KEY ON”
POWER FOR CAMERA *Camera not provided
-----------------------------------------------------
RED BARREL/ 12V CAM POWER 8-PIN (male plug)
1. Set dip switch number “1” on both C-125 and C-500 to “ON”.
(male plug)
YELLOW RCA/ VIDEO SIGNAL
RED/ CAMERA POWER
CAMERA
RED BARREL/ 12V CAM POWER
WHITE/ REVERSE 12V OUTPUT
ON 1
NOTE: The radio system will go through a reboot process that may take up to 1 minute. It will initialize and re-load all previous settings. Once complete it will resume the original radio display.
INTERFACE TO FACTORY DISPLAY
1. Remove the factory display to gain access to the factory connectors. YELLOW RCA/ VIDEO SIGNAL 2. Place both interfaces with the dip switch configuration as follows: C-125 C-125 INTERFACE Dip switch number “6” to ON. INTERFACE
OPTIONAL/ GREEN WIRES TOGGLE SWITCH CONNECT TO NOT INCLUDED ACTIVATE GRID LINES
(SIGNAL FROM CAMERA) DOES NOT REQUIRE YOU TO WHITE/ OPTIONAL SCREW *Camera not provided 12V OUTPUT HOLES TAP FOR REVERSE SIGNAL
C-500
SCREW HOLES
(male plug)
6
54-PIN
(male plug)
BOTH GREEN/ 12V POWER SWITCH (SAME FUNCTION AS DIP 1) NON-PERMANENT
8-PIN
(male plug)
USING THE VIDEO IN-MOTION
This interface does not offer the Force RVC feature.
WHITE WIRES 15 FT. 12V CONNECT TO EXTENTION GREEN WIRES INVERT IMAGE TO FRONT END CONNECT TO FUSE OF THE CAR ACTIVATE GRID (NOT INCLUDED) LINES
BLACK/ GROUND
As an option we have provided a 12v output wire (WHITE) from our C-500 interface, as the vehicle does not provide av12v Acc. Do not use if not needed.
See page 2 for compatible Radio. (new cameras available)
WHITE WIRES CONNECT TO INVERT IMAGE
GREEN/ 12V POWER OF SWITCH THE CAR (SAME FUNCTION AS DIP 1) NON-PERMANENT
GREEN/ 12V POWER SWITCH (SAME FUNCTION AS DIP 1) NON-PERMANENT
(SIGNAL IS FROM MODULE)
54-PIN
(female plug)
4-PIN BARREL ---------------FOR - - - - - ---------CONNECT - - - - - - ------------CAMERA -----POWER AND SIGNAL
- Do not disconnect the airbag connection behind the radio panel. WHITE/ PRELIMINARY :12VOPTIONAL C-500 OUTPUT
(male plug)
4-PIN BARREL CONNECT FOR CAMERA POWER AND SIGNAL
PRECAUTIONS:
TO FACTORY DISPLAY
54-PIN
MyFord Touch
DOES NOT REQUIRE YOU TO TAP FOR REVERSE SIGNAL
2
3
4
5
6
Important: If both modules are not set to the same setting, this feature will not work properly. Please make sure both interfaces have Dip 1 to the ON position.
Trouble Shoot: If the VIM is not functioning, move the vehicle forward or backward to try correcting the problem.
TROUBLE SHOOTING 1. No video display from the camera. - Make sure the dip switches are in the correct position. For more support contact tech support.
Rev. 122013
INTERFACING SOLUTIONS
RVCFD-79
FORD: 2011 - 2014 2011 - 2014 2012 - 2014 2013 - 2014 2013 - 2014 2013 - 2014 2013 - 2014 2013 - 2014 2013 - 2014 2013 - 2014 2013 - 2013 2013 - 2014 2013 - 2014 2013 - 2014
REAR-VIEW INTEGRATION INTERFACE FOR FORD VEHICLES w/ MyFord Touch RADIOS COMPATIBLE RADIO:
Edge Explorer Focus Focus ST Taurus Escape F150 F150 Raptor F250, 350, 450, 550 Fusion Hybrid Fusion Energy Taurus C-Max Hybrid C-Max Energy
LINCOLN: 2011 - 2012 MKX 2013 - 2014 MKS 2012 - 2014 MKT
WORKS FOR ALL: MyFord Touch Radios
See page 2 for compatible Camera and Radio.
AVAILABLE FORD CAMERA’S: FORD EMBLEM CAMERA CFD-03E
FORD HANDLE CAMERA CFD-03F
This interface does not offer the Force RVC feature. NOTE: The radio system will go through a reboot process that may take up to 1 minute. It will initialize and re-load all previous settings. Once complete it will resume the original radio display.
www.cruxinterfacing.com
