Transcript
L9BHM_WA(VA-80BW)(GB_JP).book 0 ページ
２００６年１２月２７日 水曜日 午前１１時１９分
INSTRUCTION MANUAL Wall Mounting Bracket
VA-80BW
This installation should be made by a qualified service person and should conform to all local codes. About this manual This bracket is designed for ceiling mounting installation. Before installing and using this unit, please read this manual carefully. Be sure to keep it handy for later reference.
日本語
Important • Be careful when opening holes for installing the unit. Work with the power and video cables pulled out for easy installation. • Make sure to properly perform waterproofing for the wall where you are installing the unit. • Make sure that the surface in the installation location has no unevenness and is strong enough to bear the total weight of the unit. • Install this unit in an environment where the temperature range stays between -30°C and +50°C (-22°F and +122°F) (no condensation allowed).
bSpecifications Color: Beige Material: Metal Waterproof Standard: Conforming to IP66 Weight: Approx. 750 g (1.7 lb)
Example of outdoor use
☞P1
☞P2
Allowable Load: Max. 20 kg (44.1 lb)
Dimensions: 240 (9.4) 192 (7.6)
191 (7.5) 161 (6.3)
17(0.7) 56 (2.2)
Example of indoor use
Ǿ97 (3.8)
Accessories (For outdoor housing) 4-Ǿ10.8 (0.4) 75 (3.0) 105 (4.1)
Bolts, washers
Rubber band
Features and specifications are subject to change without prior notice or obligations.
English
CAUTION: Install this bracket securely according to this installation manual. Be aware that allowing the bracket to fall with the camera on it may cause personal injury.
Unit: mm (inch)
L9BHM_WA(VA-80BW)(GB_JP).book 1 ページ
２００６年１２月２７日 水曜日 午前１１時１９分
Indoor Type Make sure to also consult the relevant instruction manuals. Connection cables M8 (5/16”): 40 mm (1.6”) or more
the locations on the wall and drill the 1 Mark holes for the cables and screws.
A
And pull out the cables from the wall hole and pass them through the bracket as shown in the figure. the bracket to the wall using commercially 2 Fix available screws (A) in 4 places.
Video cable
A
the power board unit onto the 3 Mount attachment. (1) Pass the screws supplied with the attachment through each of the power board unit screw holes (B) and fasten them loosely using washers (4 places). (2) Align the blue sticker (C) on the attachment and the arrow (C) of the same color on the power board unit, and tighten firmly the screws loosely fastened in the previous step.
Power Board Unit: VA-84S/80S
B
3 B
B B
C; Blue
a b
Attachment: VA-80A
sticker (D) facing toward you, fix the 4 With attachment onto the bracket using the 4 bolts
E E
(E) supplied with the attachment. • To fix the attachment, use the hexagonal wrench supplied with the attachment. • Make sure that the attachment is fixed, then peel-off the sticker. the cables to the power board unit 5 Connect and mount the camera unit onto it. ☞ For details, please refer to Installation Manual that
comes with the camera unit. “Connections and Settings” “Surface Mount”
D
• Be sure to fix the bracket securely using M8 (5/16”) screws. Using other bolt sizes may cause the bracket to fall together with the camera on it. • Route the connected cables so that they do not touch the power board unit and other parts.
Attachment accessories
b
E
a Screws, washers (for power borad unit)
1
Bolts (10 mm/0.4”)
Hexagonal wrench
L9BHM_WA(VA-80BW)(GB_JP).book 2 ページ
２００６年１２月２７日 水曜日 午前１１時１９分
Outdoor Type Make sure to also consult the relevant instruction manuals.
Connection cables
M8 (5/16”): 40 mm (1.6”) or more
the locations on the wall and drill the 1 Mark holes for the cables and screws.
A
And pull out the cables from the wall hole and pass them through the bracket as shown in the figure. Video cable
the bracket to the wall using commercially 2 Fix available screws (A) in 4 places.
3
A
Mount the dome cover and the power board unit onto the housing.
B
☞ For details, please refer to the Outdoor Housing
Instruction Manual. “1. Attaching the dome cover” “2. Mounting the power board unit” the supplied rubber bands (B) to the 4 Attach housing as shown in the figure.
D
D
sticker (C) facing toward you, 5 With temporarily mount the housing on the bracket. the housing onto the bracket using 4 sets 6 Fix of supplied bolts and bolt washers (D).
C
• To fix the housing, use the hexagonal wrench supplied with the housing. • Make sure that the housing is fixed, peel off the sticker, then remove the rubber band. the cables to the power board unit 7 Connect and mount the camera unit onto it.
Outdoor Housing: VA-80EX
3
☞ For details, please refer to the Outdoor Housing
1. Attaching the dome cover
Instruction Manual. “3. Connecting cables” “4. Mounting the camera unit”
Dome Cover: • VA-CM8C (Clear) • VA-CM8S (Smoked)
• Be sure to fix the bracket securely using M8 (5/16”) screws. Using other bolt sizes may cause the bracket to fall together with the camera on it. • Route the connected cables so that they do not touch the power board unit and other parts.
3
2. Mounting the power board unit
Power Board Unit: VA-84S/80S This mounting bracket can be installed on a pole or a wall corner by using the appropriate mounting adaptor. For installation details, refer to the instruction manual for the pole mounting adaptor (VA-80AP) or the corner mounting adaptor (VA-80AC).
2
Video cable
