Var-dvk-am33 Quick Start Guide

Transcript

VAR-DVK-SOLO based on Freescale i.MX6 Development Kit Quick Start Guide 9 10 11 12 13 14 15 16 17 18 19 28 8 29 7 20 6 21 27 22 23 24 5 4 3 Top side: 1. 5V DC In Jack (J19) 2. Boot select switch (SW6) 3. LVDS0 Header (Secondary Display) 4. RS232 Header 5. LVDS1 Header (Primary Display) (J15) 6. MIPI CSI-2 Camera [optional add-on] 7. JTAG Header 8. Capacitive Touch (J7) 9. VAR-SOM-SOLO Connection 10. Headphones Out 11. Line In 12. Parallel Camera Header 13. HDMI 14. CAN Bus Header 15. USB0 Host 2 1 16. 17. 18. 19. 20. 21. 22. 23. 24. Miscellaneous Header USB1 Host I2C/SPI Header 10/100/1000Mbps Ethernet USER Button1 USER Button2 USER Button3 Reset Button OFF/ON Switch (SW5) Bottom side: 25. USB Debug (J103) 26. micro SD Card slot (J102) 27. RTC Battery Holder 28. USB0 OTG 29. Resistive Touch 26 25 DVK initial Setup 1. Carefully remove the 7” LCD and VAR-SOLOCustomBoard board from the package. 2. Connect the 7” LCD Touch and Display cables to the DVK connectors J7,J15 respectively as shown in the upper left picture. Note: Display cable connector pins 1,2 (colored in red) should be connected to J15 pins 1, 2 respectively. Touch cable – connect cable with metal contacts facing down. 3. Plug the USB type A to micro B cable between the USB debug connector (J103) and a PC USB port. 4. Plug the wall adapter’s pin into the VAR-SOLOCustomBoard 5V power jack (J19) and to a 120VAC~240VAC power source. VAR-DVK-SOLO based on Freescale i.MX6 Development Kit Quick Start Guide Setting the Host PC for Debug 1. Download any PC terminal program. Variscite suggests using Putty 2. Set PC terminal software parameters as follows: - Baud Rate: 115200 - Data bits: 8 - Stop bits: 1 - Parity: None - Flow Control: None Using Default file System 1. Set Boot select switch (SW6) left to boot from VAR-SOM-SOLO NAND. 2. Switch ON (upwards) the SW5 switch. 3. Boot messages are printed within PC’s terminal window. Booting from micro SD Card The microSD card is supplied within the package. The image can be also downloaded from Variscite FTP site. Please contact Variscite’s sales for details: [email protected] 1. Verify Switch SW5 is OFF (downwards). 2. Set Boot select switch (SW6) right to boot from microSD Card. 3. Push microSD card into the microSD card slot (J102) of the VAR-SOLOCustomBoard. 4. Switch ON (upwards) the SW5 switch. 5. Boot messages are printed within PC’s terminal window. Burning Recovery File System Please refer to Variscite’s wiki pages at: http://variwiki.com/index.php?title=VAR-SOMMX6_Yocto_NAND_Recovery Additional Support Links 1. Wiki pages: http://variwiki.com/index.php?title=Main_Page 2. Support Forum: http://variscite.com/support-forum/index.php 3. VAR-DVK-SOLO: http://www.variscite.com/products/evaluation-kits/var-som-solo-kits 4. VAR-SOM-SOLO: http://www.variscite.com/products/system-on-module-som/cortexa9/var-som-solo-cpu-freescale-imx6 5. VAR-SOLOCustomBoard: http://www.variscite.com/products/single-board-computers/varmx6customboard Thank you for purchasing Variscite’s product. For additional assistance please contact: [email protected]