Transcript
VCXG-53M
Art. No. 11151554
Technical Data
Digital Monochrome Matrix Camera, GigE Firmware Revision 1.1 Sensor Information Model Name Type Shutter Resolution Scan Area Pixel Size
ON Semiconductor Python 5000 1“ progressive scan CMOS global 2592 x 2048 pixels 12.44 x 9.83 4.8 μm x 4.8 μm
Data Quality
@ 20 °C, gain = 1, exposure time = 4 msec
Dark Noise () Saturation Dynamic Range SNR Quantum efficiency η
11 e- typical 8400 e- typical 57 dB typical 39 dB typical 56 % @ 536 nm typical
Acquisition Resolution Acquisition Frame Rate Interface Frame Rate Sensor Graph: Relative Response
(depends on used GigE interface performance)
Pixel Formats Partial Scan
Frame Rates / Partial Scan (Measured at Mono8/BayerRG8-Format)
Adjustable Acquisition Frame Rate Acquisition Mode Acquisition Status Exposure Mode Readout Mode
2592 px x 2048 px 28 fps | treadout = 35.3 msec (max. Resolution) @ 10 bit1) max. Frame Rate Format Resolution (@ Trigger Mode)
Full Frame 2592 x 2048 23.5 fps Binning 2x2 1296 x 1024 28.0 fps Binning 2x1 1296 x 2048 28.0 fps Binning 1x2 2592 x 1024 28.0 fps Mono8, Mono10 True Partial Scan with increasing Frame Rate on Y direction, Region of Interest (ROI) arbitrary Off or 0.01 … 1780 Hz Continuous, Single Frame and Multi Frame AcquisitionActive, AcquisitionTrigger Wait Timed Overlapped, Sequential
Image Pre-Processing Analog Controls
Digital Output: High Active
1)
Gamma Correction LUT Color Models Color Tolerance Color Processing Color Adjustment Binning Horizontal Binning Vertical Image Flipping Defect Pixel Correction Fix Pattern Noise Correction
Exposure Time (20 µsec … 1 sec | Step Size 1 µsec) Gain (0…12 dB), Offset (0 ... 63 LSB | 10 bit) Gamma (0.1 … 2 | available if LUT is enabled) Luminance (12 bit) Mono 1 or 2 1 or 2 Horizontal, vertical via Defect Pixel List with up to 512 Pixel Coordinates Yes
Sensor readout, different from pixel format
The Information in this document is subject to change without notice.
TDS_VCXG-53M 25.08.2016
1
Baumer Optronic GmbH Radeberg, Germany
Digital Output: Low Active
Process Synchronization Trigger Mode Trigger Overlap Type Trigger Sources
Off (Free Running), On (Trigger) Readout Hardware (Line0,1,2), Software, All, ActionCMD (Action 1) or Off Trigger Delay out of treadout: 6 μsec @ 10 bit1) max. Trigger Delay during treadout: 42 μsec @ 10 bit1)
Trigger Delay
Digital Input
0 ... 2 sec, Tracking and buffering of up to 0 ... 2 sec, Tracking and buffering of up to 256 triggers Sequencer Characteristics Sequencer Parameters External Flash Sync via Exposure Active tdelay flash ≤ 3 µsec, tduration =texposure
Digital I/Os Lines Output Sources
Input: Line 0, Output: Line3, GPIO: Line 1, Line 2 Off, ExposureActive, Timer1, ReadoutActive, UserOutput 1 and TriggerReady Low and high signal separately selectable Debouncing Time 0 … 5 msec, Step Size: 1 μsec
Line Debouncer Trigger Mode: Start up time and valid Trigger
Interfaces and Connectors Data and Power Interface
Process Interface GPIO IN
GPIO
Caution
Gigabit Ethernet Transfer Rate 1000 Mbits/sec Fast Ethernet Transfer Rate 100 Mbits/sec Connector: 8P8C Modular Jack (RJ45) screw lock type Pin Assignment: 1 – MX1+ 5 – MX32 – MX16 – MX23 – MX2+ 7 – MX4+ 4 – MX3+ 8 – MX4Connector: M8/8-pin (SACC-DSI-M8FS-8CONM10-L180 SH) Assignment 1 – GPIO (Line2) 5 – Power VCC OUT1 : 2 – Power Vcc 6 – OUT1 (Line3) 3 – IN1 (Line0) 7 – GND (Power, GPIO) 4 – GND IN1 8 – GPIO (Line1) * Note GPIOs: Ground loops are to be avoided and can lead to destruction of the device.
Mechanical Data Housing
Zinc die casting, nickel-chrome-plated, IP40 (with mounted lens and GigE cable)
Dimensions
GPIO OUT High Active
Weight
120 g
The Information in this document is subject to change without notice.
TDS_VCXG-53M 25.08.2016
2
Baumer Optronic GmbH Radeberg, Germany
Pin Assignment Data Interface
Optical Data Lens Mount Optical Filter
C-Mount -
Electrical Data Power Supply (ext.) Power over Ethernet
Pin Assignment Process Interface (on camera side)
5
6
Power Consumption
Digital Input
4
7
3 1
2 8
wire colors on connecting cables (ordered separately) 1 White 5 Grey 2 Brown 6 Pink 3 Green 7 Blue 4 Yellow 8 Red
Device Temperature: T = Measurement Point
Digital Output
GPIO GPIO used as Input:
GPIO used as Output: Caution
VCC: 12 … 24 V DC ± 20% I: 282 … 563 mA Class 0 device VCC: 36 … 57 V DC I: 87 mA @ 48 VDC approx. 3.2 W @ 12VDC and 23.5 fps approx. 3.7 W @ 48 VDC (PoE) and 23.5 fps (Factory Setting “Default”) Optocoupler UIN(low) : 0.0 … 4.5 VDC UIN(high) : 11.0 … 30.0 VDC IIN : 3.0 … 10.0 mA min. Impulse Length: 2.0 μsec Optocoupler UEXT: 5 … 30 V DC IOUT: max. 50 mA tON = typ. 3 µsec tOFF = typ. 40 µsec direct, without optocoupler UIN(low) : 0.0 … 0.8 VDC UIN(high) : 2.0 … 30.0 VDC min. Impulse Length: 2.0 μsec UOut(low): 0.0 … 0.4 VDC (Isink max: 50 mA) UOut(high): 2.4 … 3.3VDC (Imax : 1 mA) * The General Purpose I/Os (GPIOs) are not potential-free and do not have an overrun cut-off. Incorrect wiring (overvoltage, undervoltage or voltage reversal) can lead to defects in the electronic system. Ground loops are to be avoided and can lead to destruction of the device.
LED Signalling Green flash Green Yellow Yellow flash
LED
LED Signalling
Environmental Data Storage Temperature Operating Temperature
Int. Temperature Sensor Humidity
Conformity
RX active Link ON Error TX active
-10 °C … +70 °C +5 °C … +65 °C @ T = Measurement Point or +5 °C … +75 °C @ internal Temperature Sensor Ambient temperature above 30 °C requires cooling measures. 0 °C ... +85 °C accuracy: ±1 K 10 % … 90 % non-condensing
Network Interface Data Interface Ethernet IP Configuration Packet Size Image Buffer
Gigabit Ethernet 1000BASE-T 1000 Mbits/sec Fast Ethernet 100 BASE-T 100 Mbits/sec Persistent IP, DHCP, LLA 576 … 9000 Byte, Jumbo Frames supported 8 Images (Trigger Mode) / 1 Image (Free Running Mode)
The Information in this document is subject to change without notice.
TDS_VCXG-53M 25.08.2016
3
Baumer Optronic GmbH Radeberg, Germany
®
GigE Vision Features Events Transmission via Asynchronous Message Channel
Action CMD Frame Counter Payload Size Timestamp Packet Delay Packet Resend GigE Vision
GenICam
TM
PrimaryApplicationStitch, GigEVisionError, GigEVisionHeartbeatTimeOut, EventLost, Line0..3 FallingEdge, Line0..3 RisingEdge, ExposureStart, ExposureEnd, FrameStart, FrameTransferSkipped, TransferBufferFull, TriggerReady, TransferBufferReady, TriggerOverlapped, TriggerSkipped yes, Action 1 for Trigger up to 232 0 … 10617044 Byte 64 bit 0 .. 232– 1 Ticks Resend Buffer: 41 MB (8 Images) v2.0 (v1.2 backward compatible)
Features Timer Selector: Timer 1 TimerTriggerSource: Line0, SoftwareTrigger, ExposureStart, ExposureEnd, FrameTransferSkipped, TriggerSkipped, Action 1 and Off TimerDelay: 0 μsec … 2 sec, Step Size: 1 μsec TimerDuration: 10 μsec … 2 sec, Step Size: 1 μsec Factory Settings: UserSet0 (read only) Freely Programmable: UserSet1, UserSet2, UserSet3 Parameters: any user definable Parameter Delay up to 35.3 msec v2.1
Timer
User Sets
Acquisition Abort SFNC Version
Factory Settings after Start-Up Trigger Mode Analog Controls Pixel Format Partial Scan Acquisition Frame Rate Timer Defect Pixel Correction Fixed Pattern Noise Correction Digital Input Digital Output GPIO 1/2 TriggerSource
Off (Free Running) Exposure Time: 4 msec, Gain: 0 dB, Offset: 0 Mono8 Off Off Off ON ON Line0, invert = false Line3, invert = false, line source = Off Line1, Line2, invert = false, LineMode = Input All
The Information in this document is subject to change without notice.
TDS_VCXG-53M 25.08.2016
4
Baumer Optronic GmbH Radeberg, Germany
