Transcript
NETWORK SOLUTIONS
VDSLCPEAP VDSL In-Room Splitter - With built-in power injector, filter, wireless AP, support 4 SSID
Overview
The VDSL12Port work together with CPEs at the user-side: VDSLCPE: Standard VDSL modem VDSLCPEAP: VDSL modem / bridge with integrated 802.11g AP Each CPE comes with a built-in POTS splitter to allow simultaneous connection of voice and IP devices. The CPE also comes complete with a Power Over Ethernet (PoE) for easy deployment. VDSLCPEAP comes with built-in wireless access point.
Hardware Configuration
One RJ-45 VDSL/PoE port One RJ-45 10 BaseT/100BaseTX LAN port One RJ-11 port for connection to a telephone Front panel LEDs to indicate various link status
Features Hardware Interface Antenna
One standard PCB Antenna (internal)
Antenna Connector
50 Ω antenna connectors for external antenna connection (optional)
One WAN Port
RJ-45 connector to upstream network/phone line
Two Ethernet Ports
10/100 Base-T (RJ-45 connector) with audio MDIX
DC-IN
9~14V DC thru RJ-45, 12 Watts (optional) 12V DC Jack, 12 Watts (optional)
Hardware Reset (Power Up + Press Down Reset Button)
Reset Back to default factory settings
Hardware Restore (Press Down Reset Button)
Restore settings to last known good state
Interface Standard Wireless LAN
IEEE 802.11 g
LAN
IEEE 802.3 g, 802.3 u
Internet and Intranet Bridge Mode
Bridge between WLAN and Ethernet (see both the MAC addresses of the AP and client, including wired client and wireless client at the gateway server)
Filtering
Selectable Protocol Filtering (IPX, Apple Talk) Broadcast and multicast filtering
WLAN Roaming
Support seamless roaming within the same subnet (this requires appropriate network architecture)
Access Point
Support up to 64 WLAN users, support up to 50 concurrent users
Device Management and Monitor Firmware Upgrade
Firmware upgradeable through Web-server
Telnet
Command line interface for configuration
Web Based Management
Configure and monitor each device through Web browser
Device Search (Viper-QuickStart)
Utility for locating device’s static IP address, subnet mask and MAC address
Software Restore
Restore settings to last known good state
Save Last Known Good State
Save only all active settings
Administrator Authentication
Administrator need to authenticate before configuring the device by providing User ID and Password
SNMP Read
SNMP 802.3 MIBs I & II, 802.11 MIB
Statistic
Ethernet, Wireless
Auto Radio Channel Selection
Automatically identify the most clear or un-used channel to be used at power-up time
Associate MAC address List
Display Associated MAC address
Safety and Access Control Static WEP
64, 128 and 152 Bits encryption
802.1x
Support 802.1x TLS
WPA-PSK
802.1x with dynamic WEP
MAC Address Filtering
Only allow MAC address could pass thru Remark: reject connection, allow wireless associated
Configuration Control
Administrator need to authenticate before configuring the device Remark: user ID and password
Disable SSID Broadcast
Do not broadcast wireless SSID to improve corporate network security Remark: administrator selectable
Wireless Configuration
Disable configuration by wireless clients as a security measure Remark: administrator selectable
Wireless To Wireless LAN client Isolation
Prevent WLAN clients from seeing each other Remark: administrator selectable
Specifications CPE Specifications
Supports subscriber-site plug-and-play operations; VDSL link rates are automatically controlled from remote VDSL concentrators Built-in POTS/ISDN splitter LAN port auto-senses/configures 10/100 Mbps Supports link rates of up to 15 Mbps for distances of up to 1.5km
Electrical Specifications Adaptor Input Voltage
90~264 Vac, 50/60Hz
DC Input Voltage
9~14 V, DC Thru RJ45, 12 Watts or 12 V, DC Thru DC Jack 1 A
Environmental Specifications Operating Temperature
0~50 degree C, ambient temperature
Relative Humidity When Operational
20~90% (non condensing)
Storage Temperature
-20~+75 degree C, ambient temperature
Relative Humidity During Storage
95% Mac (non condensing)
RF Specifications Frequency Range
2.4~2.4835 GHz
Data Rate
57, 48, 36, 24, 18, 12, 11, 9, 6, 5.5, 2, 1 Mbps & 108 Mbps at turbo Mode (optional)
Channels
11 channels (USA) 13 channels (Singapore) 14 channels (Japan)
Transmitter Output Power
18dBm +/- 2dBm
Nominal Antenna Port Impedance
50 Ω (for optional external antenna connector, if applicable)
Media Access protocol
CSMA/CA with ACK
Modulation Technique
OFDM, CCK, DQPSK, DBPSK
Receiver Sensitivity
54 Mbps/10% PER/-68dBm 48 Mbps/10% PER/-68dBm 36 Mbps/10% PER/-75dBm 24 Mbps/10% PER/-79dBm 18 Mbps/10% PER/-82dBm 12 Mbps/10% PER/-84dBm 11 Mbps/8% PER/-82dBm 9 Mbps/10% PER/-87dBm 6 Mbps/10% PER/-88dBm 5.5 Mbps/8% PER/-85dBm 2 Mbps/8% PER/-86dBm 1 Mbps/8% PER/-89dBm
Ordering Information Part No.
VDSLCPEAP
Product Description
VDSL In-Room Splitter - With built-in power injector, filter, wireless AP, support 4 SSID
More Information Learn more about our XPossible Connect solutions at www.xpossible.com
XPossible Technologies was established in 2002 with offices in Bangkok and Singapore. It focuses on high-speed internet solutions for the hospitality industry. The company has local partners and customers in Singapore, Malaysia, Thailand, Indonesia, Cambodia, Vietnam, and Dubai.
Thaicom Public Company Limited (formerly known as Shin Satellite) was founded in 1991 by Shin Corporation Plc. Currently, THAICOM Plc. operates four types of businesses including satellite transponder leasing and related services, internet-related services, telephone-related services (overseas), and telephone directories and distribution. XPossible is their solutions partner for Internet Services for Hotel, Service Apartment, Hospital, etc.
© 2008 XPossible Technologies Pte. Ltd. All rights reserved
