Transcript
Velocitydvi-3 A/N+
The Velocitydvi Digital Video/Audio/Network Extension System-3 A/N+ from Thinklogical™ permits the placement of a digital monitor or projector, audio devices and 10/100 ethernet up to 1000 meters (3280 feet) away from a controlling computer without loss of resolution. Each system consists of a transmitter and a receiver connected by multi-mode fiber optic cable(s). Dual fiber is used for some DDC modes to provide communications to and from the transmitter and is required for network connectivity. The receiver unit provides an interface to the display, audio devices and network. Installation is plug-and-play and no adjustments are necessary.
QUICK START GUIDE
Each of the Thinklogical™ DVI A/N+ Extension Systems is designed for high resolution video, audio and network extension applications such as remote projection centers, theaters and assembly halls, and for secure computer installations. It is now possible to position the monitor or projector in any setting from office to lecture hall to boardroom while keeping the computer secure in a remote, controlled location. All physical connections to the product use industry-standard connectors.
STEP 5: Connect the supplied AC
FOL
The Future of Access and Control
TX RX LNK/ACT
Power 5VDC +
Velocitydvi
L1: Data Tx to Rx and Video L2: Data Rx to Tx
Status
Connect L1 to L1 and L2 to L2: Optical Fibers available with ST-, SC- or LC-type connectors.
DVI to Local Display
Transmitter
Powered by MRTS Technology
Transmitter
STEP 4: Connect your fiber optic cable, up to 1000 meters (available through
DVI-D Connector 1
6
TX RX LNK/ACT
Connect one end of a DVI-D Male to Male Cable to the Video Source (DVI-D video card). Connect the other end to the Transmitter’s DVI from CPU connector. A local display may also be connected using the supplied 2 meter DVI-D Male to Male Cable (CBL-000009-002MR).
5VDC
3
+
Velocitydvi
Network
FD COL
Line OUT ►
Status
Powered by MRTS Technology
Power Supply
Receiver
The Status LEDs on the Tx and Rx units are used to indicate the status of connections to the extender. Tx Status LED · Green = Fiber L2 is connected and a good link is established. · Orange = Local Static Mode selected and no fiber link from Rx to Tx (L2 is not connected) or both DDC mode buttons are held down and the unit is waiting to reload the default DDC table. · Red Flashing = No Fiber Link from Rx to Tx (Not available in Local Static mode.) Rx Status LED · Green = Good Link and DVI device connected to primary port (port on left in the diagram below). · Orange = No DVI device connected to primary port. · Red Flashing = No Fiber Link from Tx to Rx (L1 is not connected).
The Primary Port on the Rx is used for DDC. The Secondary Port carries video data only. Acquire Button · Used to initiate DDC collection. Works with all modes except Pass-Thru. Must be pressed after switching between DDC modes. Select Button · Used to select the DDC mode. The modes will cycle through Remote Dynamic, Remote Static, Pass-Thru and Local Static. Both Buttons held 5 seconds · Holding both buttons for 5 seconds will reload the default DDC table into the Tx and switch to Remote Static mode. 100/10: When lit, speed of link is 100 Mb. When off, speed of link is 10 Mb. FD/COL: When lit, indicates operation in Full Duplex. When off, indicates operation in Half Duplex. When blinking, indicates Collision.
Optional Secondary DVI Port Primary DVI Port DDC
Select REM LCL
Acquire
DDC Mode
GND
to the appropriate Receiver ports. Turn the devices ON.
L2 ◄ Data L1 ► Video/Data
Fiber-optic cable ports.
STEP 2: Connect your Mic IN, Line OUT and CAT5 Cable
Digital Video Extension System – 3A/N+
Receiver
2
◄ Mic IN
DVI to Display
Power
Local Monitor
*The Transmitter and Receiver Network Ports can be used interchangeably as an input or an output.
Network
Line Out Mic In
Connect the supplied AC Power Adapter (PWR000022-R) to the Receiver and plug it in to a standard AC source.
The Future of Access and Control
CPU
RJ45 Network Device*
DVI to Display DDC
STEP 3:
FOL
DVI-D Connector 2
STEP 6:
Thinklogical™) between the Transmitter and Receiver Units. Do not kink or pinch the cable and be sure to keep all bend radii to no less than 3 inches.
100 10
4
LCL
DDC Mode
L1 L2
Acquire
L1 ◄ Video/Data L2 ► Data
7
Mic OUT ►
Digital Video Extension System – 3A/N+
FOL, TX, RX and LNK/ACT indicator LEDs
When lit, the solid green LED indicates that power is applied.
Active Network
◄ Line IN
DVI from CPU
·
5
Network
Select
·
DVI Extender Transmitter DVI Extender Receiver DVI-D Male to DVI-D Male Cable, 2 Meter (CBL00009-002MR) Two CAT5 Cables, 2M (CBL000001-002M) Two 3.5mm Audio Cables (CBL000016-006FR) Two Universal AC Power Adapters (PWR-000022-R) DVI Extender Product Manual
Mic Out Line In
· ·
Power Supply
the CPU to the appropriate Transmitter ports. Connect the Network Cable to an active Network. Ensure that all the devices are turned on and all system functions are operating properly.
REM
· · ·
Power Adapter (PWR-000022-R) to the Transmitter unit and plug it in to a standard AC source.
100 10
Upon receiving your Thinklogical™ Velocitydvi-3 A/N+ Extender System, you should find the following items:
STEP 7: Connect the Line IN and Mic OUT audio cables from
Network
Contents
FD COL
Digital Video, Audio and Network Extension System
STEP 1:
1
On the RJ45 connector: Green LED = Link Yellow LED (blinking) = Activity
Secondary DVI Port
LCL OFF
Projector
REM
DDC MODE
GREEN
REMOTE DYNAMIC
EDID READ FROM REMOTE DISPLAY AND UPDATED EACH TIME REMOTE DISPLAY CHANGES.
REMOTE STATIC
EDID READ FROM REMOTE DISPLAY WHEN ACQUIRE BUTTON IS PRESSED.
PASSTHRU
ACTS AS A DIRECT CONNECTION BETWEEN CPU AND DISPLAY. NO EMULATION IS PERFORMED.
LOCAL STATIC
EDID READ FROM LOCAL DISPLAY WHEN ACQUIRE BUTTON IS PRESSED.
ORANGE GREEN
Connect one end of a DVI-D Male to Male Cable to the primary viewing device. Connect the other end of the cable to the Primary (left) Receiver DVI-D connector. A second device can also be installed to the right- side, secondary port using a similar DVI-D Male to Male cable. If using only one device, it must be connected to the Primary Port. Turn ON the DVI video device(s).
GREEN GREEN
GREEN ORANGE
DESCRIPTION
Copyright © 2010. All rights reserved. Printed in the U.S.A. All trademarks and service marks are the property of their respective owners.
PHONE: WEBSITE: EMAIL:
1-800-291-3211 www.thinklogical.com
[email protected]
VELOCITY-3AN+_Quick_Start_Rev_A
Visit us online at www.thinklogical.com for more product information, current updates and the complete line of Thinklogical™ products.
