Vf-at-nk Install Pg2-3

Transcript

Step 7. Cable Management - Ensure Arm is fully extended. *To insert Cable Covers: Route the Cables underneath the Arms, inserting the Primary and Secondary Arm Cable Covers to hold the Cables in place. IMPORTANT: The “User Operating Card” must be left with Visidec Focus Articulated Arm once installed. VF-AT-NK Installation Instructions visidec Focus Notebook Mount Accessory Component Checklist ec id is v Hardware A. Insert tabs... Primary Arm Cable Cover Self Adhesive Hook-and-Loop Fasteners (x4 sets) B. Push in... Insert Primary Arm Cable Cover* Notebook Tray and Arm Assembly Insert Secondary Arm Cable Cover* TIP: Leave enough slack in the cables at the joints to allow full movement. C. Then push up Step 8. Display Alignment Set the height and position of the Notebook Tray and Monitor as desired. The height can be adjusted by unlocking the Handgrips (see Steps 3, D and E). For the optimal position of your display, refer to the Ergonomic Guidelines in your ‘User Operating Card’. Secondary Arm Cable Cover Hand Grip IMPORTANT INFORMATION ! ! ! ! ! IMPORTANT - Install Visidec Focus Notebook Mount as per Installation Instructions. This product is deisgned to be used in conjuction with an external keyboard and mouse. To be used with existing Visidec Focus Mount. Visidec Focus Notebook Mount supports Notebooks up to 18”, weighing up to 8kg (17 1/2lbs). The Manufacturer accepts no responsibility for incorrect installation. Step 1. Check Components Check you have received all parts against the Component Checklist and Hardware above. Step 2. Remove existing Arm and Monitor from Visidec Pole (ensure monitor cables are unplugged) Remove the Pole Top Cap and 5mm Allen Key from the Visidec Pole. UP Handgrips BACK: FRONT: Installation Complete Whilst supporting the weight of the Monitor, unlock the Hand Grip. Monitor Lift the Monitor and Focus Arm, removing them both from the Visidec Pole. Hand Grip UP Pole Top Cap 5mm Allen Key UNLOCK Your Visidec Focus Notebook Mount installation is complete and ready for use. Visidec Pole Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 22.04.09 © Visidec Pole Step 3. Attach the new Arm Assembly onto the Visidec Pole A. Slide the Handgrip onto the top of the Visidec Pole so the Handgrip Tab protrudes. B. Slip the Arm Assembly over the Handgrip Tab and then onto the Visidec Pole. Step 5. Install the Notebook Computer C. Slide the Arm Assembly towards the base of the Visidec Pole. Handgrip Tab A. Adjust the Support Tabs to suit the width of your Notebook Computer. Notebook Computer NOTE: Ensure that the Support Tabs do not obstruct any cable ports. Handgrip B. To increase stability, use the Self Adhesive Hook-and-Loop Fasteners supplied: Arm Assembly D. Lock the Handgrip UÊÊ*iiÊœvvÊ̅iÊL>VŽˆ˜}Ê«>«iÀÊvÀœ“Ê̅iÊ>ÃÌi˜iÀð UÊÊ
ÌÌ>V…Ê>ÃÌi˜iÀÃÊ̜ÊޜÕÀÊ œÌiLœœŽÊ Computer and the Notebook Tray. UÊÊ ˜ÃÕÀiÊ̅>ÌÊi>V…ÊÃiÌʜvÊ>ÃÌi˜iÀÃÊ>Ài correctly aligned, i.e. Hook to Loop. Notebook Tray Support Tabs (x2) >ÃÌi˜iÀÃÊ­œœŽÊÝ{® Step 4. Re-install the existing Arm and Monitor B. Lock the Monitor Arm Handgrip. LOCK Handgrip >ÃÌi˜iÀÃÊ­œœ«ÊÝ{® Notebook Tray Step 6. Connect Cables Connect cables to your Notebook Computer. Cables A. Slide the existing Arm and Monitor onto the Visidec Pole. C. Position your Notebook Computer onto the Notebook Tray. Notebook Computer Lift the Cable Management Clip on the back of the Notebook Tray, and route the Cables underneath. Release the Clip to hold the Cables in place. Cable Management Clip C. Replace the Pole Tap Cap and 5mm Allen Key, inserting them into the top of the Visidec Pole. Pole Top Cap LIFT 5mm Allen Key Cables