Video 2.5 Hdd

Transcript

Video 2.5 HDD Product Manual Standard models ST500VT000 ST500VT001 ST320VT000 ST250VT000 100713733, Rev. E Gen 2.1 - April 2016 Document Revision History Revision Date Pages affected and Description of Change Rev. A 07/24/2013 Initial release. Rev. B 05/02/2014 16. Rev. C 11/07/2014 4 & 11. Rev. D FC: New logo & cover design 4: Updated 1st & last support URLs 09/24/2015 7 & 14: Revised Rated Workload statement All: New page numbering convention applied. BC: New logo Rev. E 04/28/2016 7 & 14: Updated Warranty link text to "Is my Drive under Warranty" 15: Updated Section 2.12 Agency Certification a © 2016 Seagate Technology LLC. All rights reserved. Publication number: 100713733, Rev. E April 2016 Seagate, Seagate Technology and the Spiral logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. 3D Defense System and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. The FIPS logo is a certification mark of NIST, which does not imply product endorsement by NIST, the U.S., or Canadian governments. All other trademarks or registered trademarks are the property of their respective owners. No part of this publication may be reproduced in any form without written permission of Seagate Technology LLC. Call 877-PUB-TEK1(877-782-8351) to request permission. When referring to drive capacity, one gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion bytes. Your computer’s operating system may use a different standard of measurement and report a lower capacity. In addition, some of the listed capacity is used for formatting and other functions, and thus will not be available for data storage. Actual quantities will vary based on various factors, including file size, file format, features and application software. Actual data rates may vary depending on operating environment and other factors. The export or re-export of hardware or software containing encryption may be regulated by the U.S. Department of Commerce, Bureau of Industry and Security (for more information, visit www.bis.doc.gov), and controlled for import and use outside of the U.S. Seagate reserves the right to change, without notice, product offerings or specifications. Contents Seagate® Technology Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1.1 About the Serial ATA Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.0 Drive Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2.1 Formatted Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.1.1 LBA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.2 Physical organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.3 Recording and Interface Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.4 Physical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 2.5 Seek time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.6 Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.7 Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.7.1 Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.7.2 Conducted noise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 2.7.3 Voltage tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 2.7.4 Power management modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 2.8 Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 2.8.1 Shock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 2.8.2 Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 2.9 Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 2.9.1 Test for prominent discrete tones (PDTs). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 2.10 Electromagnetic Immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 2.11 Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 2.11.1 Annualized Failure Rate (AFR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 2.12 Agency Certification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 2.12.1 Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 2.12.2 Electromagnetic Compatibility (EMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 2.12.3 FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 2.13 Environmental Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 2.13.1 European Union Restriction of Hazardous Substances (RoHS) Directive . . . . . . . . . . . . . .16 2.13.2 China Restriction of Hazardous Substances (RoHS) Directive . . . . . . . . . . . . . . . . . . . . . . . .16 2.14 Corrosive Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 3.0 Configuring and Mounting the Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 3.1 Handling and Static-Discharge Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 3.2 Configuring the Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 3.2.1 Serial ATA Cables and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 3.3 Drive Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 4.0 Serial ATA (SATA) Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 4.1 Hot-Plug Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 4.2 Serial ATA Device Plug Connector Pin Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 4.3 Supported ATA Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 4.3.1 Identify Device command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 4.3.2 Set Features command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 4.3.3 S.M.A.R.T. commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Seagate Video 2.5 HDD Product Manual, Rev. E 2 Figures Figure 1 Figure 2 Figure 3 Typical 5V Startup and Operation Current Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Attaching SATA Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Mounting Dimensions (for standard models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Seagate Video 2.5 HDD Product Manual, Rev. E 3 Seagate® Technology Support Services For information regarding online support and services, visit: http://www.seagate.com/contacts/ For information regarding Warranty Support, visit: http://www.seagate.com/support/warranty-and-replacements/ For information regarding data recovery services, visit: http://www.seagate.com/services-software/data-recovery-services/ For Seagate OEM, Distribution partner and reseller portals, visit: http://www.seagate.com/partners/ Seagate Video 2.5 HDD Product Manual, Rev. E 4 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following: Seagate® Video 2.5 HDD model drives: Standard models ST500VT000 - 1DK142 ST500VT001 - 1K6142 ST320VT000 - 1DK14C ST250VT000 - 1DK141 These drives provide the following key features:  1000 Gs nonoperating shock and 400 Gs of operating shock.  16MB buffer. (ST500VT000, ST320VT000 and ST250VT000 models)  32MB buffer. (ST500VT001 model)  5400-RPM spindle speed.  Full-track multiple-sector transfer capability without local processor intervention.  High instantaneous (burst) data-transfer rates (up to 6Gb/s).  Native Command Queuing (NCQ) with command ordering.  Perpendicular recording technology.  Quiet operation. Fluid Dynamic Bearing (FDB) motor.  Reliability for 24x7 video applications.  SeaTools™ diagnostic software performs a drive self-test that eliminates unnecessary drive returns.  State-of-the-art cache and on-the-fly error-correction algorithms.  Support for Read Multiple and Write Multiple commands.  Support for S.M.A.R.T. drive monitoring and reporting.  The 3D Defense System™, which includes Drive Defense, Data Defense and Diagnostic Defense, offers the industry’s most comprehensive protection for disk drives.  Worldwide Name (WWN) capability uniquely identifies the drive. 1.1 About the Serial ATA Interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include:  Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jumpers or other configuration options.  Thinner and more flexible cabling for improved enclosure airflow and ease of installation.  Scalability to higher performance levels. In addition, Serial ATA makes the transition from parallel ATA easy by providing legacy software support. Serial ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disk drive in your current system and expect all of your existing applications to work as normal. The Serial ATA interface connects each disk drive in a point-to-point configuration with the Serial ATA host adapter. There is no master/slave relationship with Serial ATA devices like there is with parallel ATA. If two drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. This essentially means both drives behave as if they are Device 0 (master) devices. Note The host adapter may, optionally, emulate a master/slave environment to host software where two devices on separate Serial ATA ports are represented to host software as a Device 0 (master) and Device 1 (slave) accessed at the same set of host bus addresses. A host adapter that emulates a master/slave environment manages two sets of shadow registers. This is not a typical Serial ATA environment. The Serial ATA host adapter and drive share the function of emulating parallel ATA device behavior to provide backward compatibility with existing host systems and software. The Command and Control Block registers, PIO and DMA data transfers, resets, and interrupts are all emulated. The Serial ATA host adapter contains a set of registers that shadow the contents of the traditional device registers, referred to as the Shadow Register Block. All Serial ATA devices behave like Device 0 devices. For additional information about how Serial ATA emulates parallel ATA, refer to the Serial ATA International Organization: Serial ATA (Revision 2.6). The specification can be downloaded from www.serialata.org. Seagate Video 2.5 HDD Product Manual, Rev. E 5 2.0 Drive Specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models: The specification summaries listed in the following tables are for quick reference. For details on specification measurement or definition, refer to the appropriate section of this manual. Table 1 Drive Specifications Summary Drive Specification ST500VT001 Formatted capacity (1) Guaranteed sectors ST500VT000 ST320VT000 ST250VT000 500 GB 320 GB 250 GB 976,773,168 625,142,448 488,397,168 Heads 2 Disks 1 Bytes per sector 512 (logical) / 4096 (physical) Recording density 1875 Kb/in Track density 375 Ktracks/in avg Areal density 670 Gb/in2 avg Spindle speed 5400 RPM Sustained data transfer rate OD 100 MB/s max I/O data-transfer rate 600 MB/s max PIO modes 0–4 Multiword DMA modes 0–2 Ultra DMA modes 0–6 ATA data-transfer modes supported Cache buffer 32MB 16MB Height 6.8 +/- 0.2 mm (0.268 +/-.008 in) Width 69.85 +/- 0.25 mm (2.750 +/- 0.010 in) Length 100.35 +0.20 / -0.25 mm (3.951 +0.008 / -0.010 in) Weight (typical) <95 g (0.209 lb) Average latency 5.6 ms Startup current (typical) 5V (peak) 1.0 A Voltage tolerance (including noise) 5V ± 5% Operating temperature Nonoperating temperature (Ambient) Temperature gradient (max) Relative humidity Relative humidity gradient Wet bulb temperature (max) Altitude, operating Altitude, nonoperating (below mean sea level, max) Operational Shock Seagate Video 2.5 HDD Product Manual, Rev. E 0° to 60°C –40° to 70°C 20°C per hour max (operating) 35°C per hour max (nonoperating) 5% to 95% (operating) 5% to 95% (nonoperating) 30% per hour max 37.7°C max (operating) 40.0°C max (nonoperating) –304.8 m to 3048 m (–1000 ft to 10,000+ ft) –304.8 m to 12,192 m (–1000 ft to 40,000+ ft) 400 Gs at 2 ms max 6 Drive Specifications Table 1 Drive Specifications Summary (continued) Drive Specification ST500VT001 ST500VT000 Non-Operational Shock ST320VT000 ST250VT000 1000 Gs at 1 ms max 5–200 Hz: 2.0 Gs 201–500 Hz: 1.0 Gs Vibration, operating Vibration, nonoperating 5–500 Hz: 5.0 Gs 1 per 1014 bits read Nonrecoverable read errors Annualized Failure Rate (AFR) 0.55% Rated workload Average annualized workload rating: <55 TB/year. The AFR specification for the product assumes the I/O workload does not exceed the average annualized workload rate limit of 55 TB/year. Workloads exceeding the annualized rate may degrade the product AFR and impact reliability as experienced by the particular application. The average annualized workload rate limit is in units of TB per calendar year. Warranty To determine the warranty for a specific drive, use a web browser to access the following web page: http://www.seagate.com/support/warranty-and-replacements/ From this page, click on the “Is my Drive under Warranty” link. The following are required to be provided: the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for the drive. Load-unload cycles 600,000 at 25°C, 50% rel. humidity Supports Hotplug operation per the Serial ATA Revision 3.2 specification 1. Yes One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. 2.1 Formatted Capacity Model Formatted Capacity(1) Guaranteed Sectors 500GB model 500 GB 976,773,168 320GB model 320 GB 625,142,448 250GB model 250 GB 488,397,168 1. 2.1.1 Bytes per Sector 512 (logical) / 4096 (physical) One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above. Refer to Configuring and Mounting the Drive on page 17 (words 60-61 and 100-103) for additional information about 48-bit addressing support of drives with capacities over 137 GB. Seagate Video 2.5 HDD Product Manual, Rev. E 7 Drive Specifications 2.2 Physical organization Drive model Read/write heads Number of disks 2 1 ST500VT000 and ST500VT001 ST320VT000 ST250VT000 2.3 Recording and Interface Technology Interface Serial ATA (SATA) Recording method Perpendicular Recording density 1875 Kb/in Track density 375 ktracks/in avg Areal density 670 Gb/in2 avg Spindle speed 5400 RPM +/- 0.2% Sustained data transfer rate 100 MB/s max I/O data-transfer rate 600 MB/s max 2.4 Physical Characteristics Height 6.8 +/- 0.2 mm (0.268 +/-.008 in) Width 69.85 +/- 0.25 mm (2.750 +/- 0.010 in) Length 100.35 +0.20 / -0.25 mm (3.951 +0.008 / -0.010 in) Typical weight <95 g (0.209 lb) All models ST500VT000, ST320VT000 and ST250VT000 16 MB (16,192 KB) Cache buffer ST500VT001 2.5 32MB (32,384 KB) Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows:  Track-to-track seek time is an average of all possible single-track seeks in both directions.  Average seek time is a true statistical random average of at least 5000 measurements of seeks between random tracks, less overhead. Table 2 Typical seek times Typical seek times (ms) Read Track-to-track 1.5 Average 12.0 Average latency 5.6 Note These drives are designed to consistently meet the seek times represented in this manual. Physical seeks, regardless of mode (such as track-to-track and average), are expected to meet the noted values. However, due to the manner in which these drives are formatted, benchmark tests that include command overhead or measure logical seeks may produce results that vary from these specifications. Seagate Video 2.5 HDD Product Manual, Rev. E 8 Drive Specifications 2.6 Start/stop times Table 3 Start/stop times Typical seek times (ms) Typical Max @ 25°C Power-on to ready 3.0 4.0 Standby to ready 2.5 3.0 2.7 Power Specifications The drive receives DC power (+5V) through a native SATA power connector (refer to Figure 2). 2.7.1 Power consumption Power requirements for the drives are listed in the table in Table 4. Typical power measurements are based on an average of drives tested, under nominal conditions, at 25°C ambient temperature. These power measurements are done with Interface Power Management modes like HIPM and DIPM enabled.  Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.  Seek mode During seek mode, the read/write actuator arm moves toward a specific position on the disk surface and does not execute a read or write operation. Servo electronics are active. Seek mode power is measured based on three random seek operations every 100 ms. This mode is not typical.  Read/write power and current Read/write power is measured with the heads on track, based on three 63 sector read or write operations every 100 ms.  Idle mode power Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in a random track location.  Standby mode During standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/write electronics are in power-down mode. Table 4 DC Power Requirements Power Dissipation +5V input average (25° C) Spinup (max) 1.00A Seek average 1.40W Write average 1.70W Read average 1.30W Idle, performance (1) 1.20W Idle, active 0.70W Idle, low power mode 0.45W Standby(2) 0.18W Sleep 0.18W 1. 2. During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. Standby power is measured at steady state (after 200ms from transition) Seagate Video 2.5 HDD Product Manual, Rev. E 9 Drive Specifications 2.7.1.1 Typical current profiles The typical 5V startup and operation current profile is shown in Figure 1. Figure 1 Typical 5V Startup and Operation Current Profile Seagate Video 2.5 HDD Product Manual, Rev. E 10 Drive Specifications 2.7.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line.  Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at up to 20 MHz. Note 2.7.3 Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current. Voltage tolerance Voltage tolerance (including noise):  +5V ± 5% 2.7.4 Power management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, power management is controlled through the system setup program. The drive features the following power-management modes: Power modes Heads Spindle Buffer Active (operating) Tracking Rotating Full power Idle, performance Tracking Rotating Self refresh—low power Idle, active Floating Rotating Self refresh—low power Idle, low power Parked Rotating Self refresh—low power Standby Parked Stopped Self refresh—low power Sleep Parked Stopped Self refresh—low power  Active mode The drive is in active mode during the read/write and seek operations.  Idle mode The buffer remains enabled, and the drive accepts all commands and returns to active mode any time disk access is necessary.  Standby mode The drive enters standby mode when the host sends a standby Immediate command. If the host has set the standby timer, the drive can also enter standby mode automatically after the drive has been inactive for a specifiable length of time. The standby timer delay is established using a standby or idle command. In standby mode, the drive buffer is enabled, the heads are parked and the spindle is at rest. The drive accepts all commands and returns to active mode any time disk access is necessary.  Sleep mode The drive enters sleep mode after receiving a sleep command from the host. In sleep mode, the drive buffer is disabled, the heads are parked and the spindle is at rest. The drive leaves sleep mode after it receives a hard reset or soft reset from the host. After receiving a reset, the drive exits sleep mode and enters standby mode with all current translation parameters intact.  Idle and standby timers Each time the drive performs an active function (read, write or seek), the standby timer is reinitialized and begins counting down from its specified delay times to zero. If the standby timer reaches zero before any drive activity is required, the drive makes a transition to standby mode. In both Idle and standby mode, the drive accepts all commands and returns to active mode when disk access is necessary. Seagate Video 2.5 HDD Product Manual, Rev. E 11 Drive Specifications 2.8 Environmental Specifications This section provides the temperature, humidity, shock, and vibration specifications for Momentus drives. Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Above 1000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet. The maximum allowable drive case temperature is 65°C (149°F) Table 5: Environmental specifications Parameters Operating Non-Operating Ambient temperature 0° to 60°C (32° to 140°F) -40° to 70°C (-40° to 158°F) Temperature gradient 20°C per hour (68°F per hour) max, without condensation 35°C per hour (95°F per hour) max, without condensation Humidity 5% to 95% non-condensing (30% per hour) 5% to 95% non-condensing (30% per hour) Wet bulb 37.7°C (99.8°F) max 40°C (104°F) max Altitude -304.8m to 3048m (-1000ft to 10,000ft) -304.8m to 12,192m (-1000ft to 40,000ft) The recommended storage period: Note • 1 year under controlled conditions of 34°C 90%RH or less • 90 days in uncontrolled storage conditions 2.8.1 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y, or Z axis. 2.8.1.1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 400 Gs based on half-sine shock pulses of 2ms. Shocks should not be repeated more than one time per axis 2.8.1.2 Nonoperating shock The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 800 Gs based on a nonrepetitive half-sine shock pulse of 2 ms duration. The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 1000 Gs based on a nonrepetitive half-sine shock pulse of 1 ms duration. 2.8.2 Vibration All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive mounting screws. Vibration may be applied in the X, Y, or Z axis. 2.8.2.1 Operating vibration The maximum vibration levels that the drive may experience while meeting the performance standards specified in this document are specified below. 5–200 Hz 2.0 Gs (0 to peak). Max displacement may apply below 10 Hz. 201–500 Hz 1.0 Gs (0 to peak). Seagate Video 2.5 HDD Product Manual, Rev. E 12 Drive Specifications 2.8.2.2 Nonoperating vibration The maximum nonoperating vibration levels that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation are specified below. 5–500 Hz 2.9 5.0 Gs (0 to peak). Max displacement may apply below 22 Hz. Acoustics Drive emission of sound is measured consistent with the ECMA-74 and its referenced standards. Testing is conducted at room temperature (approximately 25°C). Emission levels are reported as the total A-weighted sound power levers for steady state, idle, and active seeks modes of operation. Table 6 1. Drive A-weighted Sound Power Levels (SWL, BA) Idle(1) Performance Seek 2.0 bels (typ) 2.2 bels (max) 2.2 bels (typ) 2.4 bels (max) During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. 2.9.1 Test for prominent discrete tones (PDTs) Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the use of the absolute threshold of hearing. Seagate uses the lower limit for the threshold curve* to discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA-74 standards. *Defined as the median curve given by ISO 389-7 (Tf curve) minus 10dB at all frequencies. 2.10 Electromagnetic Immunity When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected to the radio frequency (RF) environment as defined in Table 7. Table 7 Radio Frequency Environments Performance Level Reference Standard Test Description Electrostatic discharge Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV B EN 61000-4-2: 95 Radiated RF immunity 80 to 1GHz, 3 V/m, 80% AM with 1 kHz sine 900 MHz, 3 V/m, 50% pulse modulation @ 200 Hz A EN 61000-4-3: 96 ENV 50204: 95 Electrical fast transient ± 1 kV on AC mains, ± 0.5 kV on external I/O B EN 61000-4-4: 95 Surge immunity ± 1 kV differential, ± 2 kV common, AC mains B EN 61000-4-5: 95 Conducted RF immunity 150 kHz to 80 MHz, 3 Vrms, 80% AM with 1 kHz sine A EN 61000-4-6: 97 Power Frequency H-field immunity 1 A/m, 50Hz/60Hz, 3 axes A EN 61000-4-8: 97 Voltage dips, interrupts 30% Reduction for 25 cycles >95% Reduction for 250 cycles >95%, 0.5 cycles C C B EN 61000-4-11: 94 Seagate Video 2.5 HDD Product Manual, Rev. E 13 Drive Specifications 2.11 Reliability 2.11.1 Annualized Failure Rate (AFR) The product will achieve an Annualized Failure Rate (AFR) of 0.55% when operated in an environment of ambient air temperatures of 25°C. Operation at temperatures outside the specifications in Section 2.8, Environmental Specifications may increase the product AFR. AFR is a population statistics that is not relevant to individual units. AFR specifications are based on the following assumptions for consumer electronics environments: • 8760 power-on-hours per year • 10,000 average motor start/stop cycles per year • Operations at nominal voltages • Temperatures outside the specifications in Section 2.8, Environmental Specifications may reduce the product reliability. • Normal I/O duty cycle for consumer electronics environments. Operation at excessive I/O duty cycle may degrade product reliability. The consumer electronics environment of power-on-hours, temperature, and I/O duty cycle affect the product AFR. The AFR will be degraded if used in a enterprise application Nonrecoverable read errors 1 per 1014 bits read, max Load/Unload (U/UL) 25°C, 50% relative humidity 600,000 software-controlled power on/off cycles 20,000 hard power on/off cycles Rated workload Average annualized workload rating: <55 TB/year. The AFR specification for the product assumes the I/O workload does not exceed the average annualized workload rate limit of 55 TB/year. Workloads exceeding the annualized rate may degrade the product AFR and impact reliability as experienced by the particular application. The average annualized workload rate limit is in units of TB per calendar year. Warranty To determine the warranty for a specific drive, use a web browser to access the following web page: http://www.seagate.com/support/warranty-and-replacements/ From this page, click on the “Is my Drive under Warranty” link. The following are required to be provided: the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for the drive. Seagate Video 2.5 HDD Product Manual, Rev. E 14 Drive Specifications 2.12 Agency Certification 2.12.1 Safety certification These products are certified to meet the requirements of UL60950-1, CSA60950-1 and EN60950 and so marked as to the certify agency. 2.12.2 Electromagnetic Compatibility (EMC) Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Electromagnetic Compatibility Directive 2004/108/EC (Until 19th April, 2016) and 2014/30/EU (From 20th April, 2016). Testing is performed to the levels specified by the product standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and the immunity levels are defined by EN 55024. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when used in the test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators should confirm EMC compliance and provide CE marking for their products. Korean RRA If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Radio Research Agency (RRA) Communications Commission, Republic of Korea. These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recognized lab. Australian RCM If these models have the RCM marking, they comply with the Australia/New Zealand Standard AS/NZS CISPR22: 2009, and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communication and Media Authority (ACMA). 2.12.3 FCC verification These drives are intended to be contained solely within a personal computer or similar enclosure (not attached as an external device). As such, each drive is considered to be a subassembly even when it is individually marketed to the customer. As a subassembly, no Federal Communications Commission verification or certification of the device is required. Seagate has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disk drive, motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is likely to result in interference to radio and television reception. Radio and television interference This equipment generates and uses radio frequency energy and if not installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception. This equipment is designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television, which can be determined by turning the equipment on and off, you are encouraged to try one or more of the following corrective measures:  Reorient the receiving antenna.  Move the device to one side or the other of the radio or TV.  Move the device farther away from the radio or TV.  Plug the computer into a different outlet so that the receiver and computer are on different branch outlets. If necessary, you should consult your dealer or an experienced radio/television technician for additional suggestions. You may find helpful the following booklet prepared by the Federal Communications Commission: How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402. Refer to publication number 004-000-00345-4. Seagate Video 2.5 HDD Product Manual, Rev. E 15 Drive Specifications 2.13 Environmental Protection Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 2.13.1 European Union Restriction of Hazardous Substances (RoHS) Directive The European Union Restriction of Hazardous Substances (RoHS) Directive, restricts the presence of chemical substances, including Lead, Cadmium, Mercury, Hexavalent Chromium, PBB and PBDE, in electronic products, effective July 2006. This drive is manufactured with components and materials that comply with the RoHS Directive. 2.13.2 China Restriction of Hazardous Substances (RoHS) Directive 中国限制危险物品的指令 This product has an Environmental Protection Use Period (EPUP) of 20 years. The following table contains information mandated by China's "Marking Requirements for Control of Pollution Caused by Electronic Information Products" Standard. "O" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is lower than the threshold defined by the China RoHS MCV Standard. “O”表示该部件（于同类物品程度上）所含的危险和有毒物质低于中国RoHS MCV标准所定义的门槛值。 "X" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is over the threshold defined by the China RoHS MCV Standard. “X”表示该部件（于同类物品程度上）所含的危险和有毒物质超出中国RoHS MCV标准所定义的门槛值。 2.14 Corrosive Environment Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM B845. However, this accelerated testing cannot duplicate every potential application environment. Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component reliability can be affected by the installation environment. The silver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulcanized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives. Seagate Video 2.5 HDD Product Manual, Rev. E 16 Configuring and Mounting the Drive 3.0 Configuring and Mounting the Drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and Static-Discharge Precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions. CAUTION 3.2 • Keep the drive in the electrostatic discharge (ESD) bag until you are ready for installation to limit the drive’s exposure to ESD. • Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure. • Handle the drive by its edges or frame only. • The drive is extremely fragile—handle it with care. Do not press down on the drive top cover. • Always rest the drive on a padded, antistatic surface until you mount it in the computer. • Do not touch the connector pins or the printed circuit board. • Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination. Configuring the Drive Each drive on the Serial ATA interface connects in a point-to-point configuration with the Serial ATA host adapter. There is no master/slave relationship because each drive is considered a master in a point-to-point relationships. If two drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. Both drives behave as if they are Device 0 (master) devices. 3.2.1 Serial ATA Cables and Connectors The Serial ATA interface cable consists of four conductors in two differential pairs, plus three ground connections. The cable size may be 30 to 26 AWG with a maximum length of one meter (39.37 in). Refer to Table 8 for connector pin definitions. Either end of the SATA signal cable can be attached to the drive or host. For direct backplane connection, the drive connectors are inserted directly into the host receptacle. The drive and the host receptacle incorporate features that enable the direct connection to be hot pluggable and blind mateable. For installations which require cables, you can connect the drive as shown in Figure 2. Figure 2 Attaching SATA Cabling Signal connector Power connector Signal cable Power cable Each cable is keyed to ensure correct orientation. Seagate Video 2.5 HDD drives support latching SATA connectors. Seagate Video 2.5 HDD Product Manual, Rev. E 17 3.3 Drive Mounting You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. Refer to Figure 3 for drive mounting dimensions. Follow these important mounting precautions when mounting the drive:  Allow a minimum clearance of 0.030 in (0.76 mm) around the entire perimeter of the drive for cooling.  Use only M3 x 0.5 mounting screws.  Do not overtighten the mounting screws. Maximum torque: 4.0 in-lb (0.4519 N-m).  Four (4) threads (0.080 in, 2.032 mm) minimum screw engagement recommended.  Avoid excessive drive distortion when mounting. Refer to the following specifications for stiffness/deflection information: Top cover stiffness/deflection Operating: no performance degradation, emitted noise, mechanical damage, or hard errors 10 mm probe: 1.02kgf or 5 mm probe: 0.92kgf Non-operating: no hard errors 20 mm probe: 2.0kgf at any point of top cover 20 mm probe: 15.0kgf at top cover edges only Figure 3 Mounting Dimensions (for standard models) 3.951 +.008 / -.010 in 100.36 +.203 / -.25 mm .835 ± .010 in 21.21 ± .25 mm .334 ± .050 in 8.48 ± 1.27 mm .324 ± .010 in 8.23 ± .25 mm BREATHER HOLE, DO NOT COVER OR SEAL 2.750 ± .010 in 69.85 ± .25 mm .551 in 13.99 mm 3.567 in 90.60 mm 268 ± .008 in 6.81 ± .203 mm 2X .118 in 2.99 mm BOTH SIDES .230 in 5.84 mm .263 in 6.68 mm .551 in 13.99 mm 3.567 in 90.60 mm 2.430 in 61.72 mm .160 in 4.06 mm Seagate Video 2.5 HDD Product Manual, Rev. E 18 Serial ATA (SATA) Interface 4.0 Serial ATA (SATA) Interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. The drive also supports the use of the IORDY signal to provide reliable high-speed data transfers. For detailed information about the Serial ATA interface, refer to the Serial ATA: High Speed Serialized AT Attachment specification. 4.1 Hot-Plug Compatibility Seagate Video 2.5 HDD drives incorporate connectors which enable you to hot plug these drives in accordance with the Serial ATA: High Speed Serialized AT Attachment specification revision 2.0. This specification can be downloaded from www.serialata.org. This device requires a COMRESET from the host after a hotplug event. 4.2 Serial ATA Device Plug Connector Pin Definitions Table 8 summarizes the signals on the Serial ATA interface and power connectors. Refer to the Notes below. Table 8 Serial ATA Connector Pin Definitions Segment Signal Pin Function Definition S1 Ground 2nd mate S2 A+ S3 A- S4 Ground S5 B- S6 B+ S7 Ground Differential signal pair A from Phy 2nd mate Differential signal pair B from Phy 2nd mate Key and spacing separate signal and power segments Power P1 V33 3.3V power P2 V33 3.3V power P3 V33 3.3V power, pre-charge, 2nd mate P4 Ground 1st mate P5 Ground 2nd mate P6 Ground 2nd mate P7 V5 5V power, pre-charge, 2nd mate P8 V5 5V power P9 V5 5V power P10 Ground 2nd mate P11 Ground or LED signal If grounded, drive does not use deferred spin P12 Ground 1st mate P13 V12 12V power, pre-charge, 2nd mate P14 V12 12V power P15 V12 12V power Notes 1 All pins are in a single row, with a 1.27 mm (0.050 in) pitch. 2 The comments on the mating sequence apply to the case of backplane blindmate connector only. In this case, the mating sequences are: • the ground pins P4 and P12. • the pre-charge power pins and the other ground pins. • the signal pins and the rest of the power pins. 3 There are three power pins for each voltage. One pin from each voltage is used for pre-charge when installed in a blind-mate backplane configuration. 4 All used voltage pins (Vx) must be terminated. Seagate Video 2.5 HDD Product Manual, Rev. E 19 4.3 Supported ATA Commands Table 9 lists Serial ATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA International Organization: Serial ATA (Revision 2.6). Refer to www.sata-io.org. Refer to S.M.A.R.T. commands on page 27 for details and subcommands used in the S.M.A.R.T. implementation. Table 9 Supported ATA commands ATA-standard commands names Command code (in hex) Device Configuration Restore B1h/C0h Device Configuration Freeze Lock B1h/C1h Device Configuration Identify B1h/C2h Device Configuration Set B1h/C3h Download Microcode 92h Execute Device Diagnostics 90h Flush Cache E7h Flush Cache Extended EAh Identify Device ECh Initialize Device Parameters 91h Read Buffer E4h Read DMA C8h Read DMA Extended 25h Read DMA without Retries C9h Read Long with Retries 22h Read Long without Retries 23h Read Multiple C4h Read Multiple Extended 29h Read Native Max Address F8h Read Native Max Address Extended 27h Read Sectors 20h Read Sectors Extended 24h Read Sectors without Retries 21h Read Verify Sectors 40h Read Verify Sectors Extended 42h Read Verify Sectors without Retries 41h Seek 70h Set Features EFh Set Max Address F9h Note: Individual Set Max commands are identified by the value placed in the Set Max Features register as defined to the right. Address: Password: Lock: Unlock: Freeze Lock: Set Max Address Ext 37h Set Multiple Mode C6h S.M.A.R.T. Disable Operations B0h/D9h S.M.A.R.T. Enable/Disable Autosave B0h/D2h Seagate Video 2.5 HDD Product Manual, Rev. E 00H 01H 02H 03H 04H 20 Serial ATA (SATA) Interface Table 9 Supported ATA commands ATA-standard commands names Command code (in hex) S.M.A.R.T. Enable Operations B0h/D8h S.M.A.R.T. Enable/Disable Auto Offline B0h/DBh S.M.A.R.T. Enable One Attribute Modification B0h/E0h S.M.A.R.T. Execute Offline B0h/D4h S.M.A.R.T. Free Fall Protection Host Interface FEh S.M.A.R.T. Read Attribute Thresholds B0h/D1h S.M.A.R.T. Read Data B0h/D0h S.M.A.R.T. Read Log Sector B0h/D5h S.M.A.R.T. Return Status B0h/DAh S.M.A.R.T. Save Attribute Values B0h/D3h S.M.A.R.T. Write Attribute Thresholds B0h/D7h S.M.A.R.T. Write Attribute Values B0h/E1h S.M.A.R.T. Write Log Sector B0h/D6h Write Buffer E8h Write DMA CAh Write DMA Extended 35h Write DMA without Retries CBh Write Long with Retries 32h Write Long without Retries 33h Write Multiple C5h Write Multiple Extended 39h Write Sectors 30h, 31h Write Sectors Extended 34h ATA-standard power-management commands Check Power Mode E5h Idle E3h Idle Immediate E1h Sleep E6h Standby E2h Standby Immediate E0h ATA-standard security commands Security Set Password F1h Security Unlock F2h Security Erase Prepare F3h Security Erase Unit F4h Security Freeze Lock F5h Security Disable Password F6h Seagate Video 2.5 HDD Product Manual, Rev. E 21 Serial ATA (SATA) Interface 4.3.1 Identify Device command The Identify Device command (command code ECH) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in Table 10. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive. Refer to Drive Specifications on page 6 for default parameter settings. The following commands contain drive-specific features that may not be included in the Serial ATA specification. Table 10 Identify Device command Word Description Value 0C5AH 0 Configuration information: • Bit 15: 0 = ATA; 1 = ATAPI • Bit 7: removable media • Bit 6: removable controller • Bit 0: reserved 1 Number of logical cylinders 16,383 2 Specific configuration C837H 3 Number of logical heads 16 4 Retired 0000H 5 Retired 0000H 6 Number of logical sectors per logical track: 63 003FH 7–9 Retired 0000H 10–19 Serial number: (20 ASCII characters, 0000H = none) ASCII 20 Retired 0000H 21 Retired 8000H 22 Obsolete 0004H 23–26 Firmware revision: (8 ASCII character string, padded with blanks to end of string) x.xx 27–46 Drive model number: (40 ASCII characters, padded with blanks to end of string) ST500VT000 ST500VT001 ST320VT000 ST250VT000 47 (Bits 7–0) Maximum sectors per interrupt on Read multiple and Write multiple (16) 8010H 48 Trusted Computing Feature set options 0000H 49 Standard Standby timer, IORDY supported and may be disabled 2F00H 50 Capabilities 4000H 51 PIO data-transfer cycle timing mode 0200H 52 Retired 0200H 53 Words 54–58, 64–70 and 88 are valid 0007H 54 Number of current logical cylinders xxxxH 55 Number of current logical heads xxxxH 56 Number of current logical sectors per logical track xxxxH 57–58 Current capacity in sectors xxxxH 59 Number of sectors transferred during a Read Multiple or Write Multiple command xxxxH Seagate Video 2.5 HDD Product Manual, Rev. E 22 Serial ATA (SATA) Interface Table 10 Identify Device command Word Description Value 60–61 Total number of user-addressable sectors This field contains a value that is one greater than the total number of user-addressable sectors. The maximum value that shall be placed in this field is 0FFFFFFFh. The 0FFFFFFFh value applies to all capacities over 137GB (see Section 2.1 for related information). ST500VT000 = 0FFFFFFFh ST500VT001 = 0FFFFFFFh ST320VT000 = 0FFFFFFFh ST250VT000 = 0FFFFFFFh 62 Retired 0000H 63 Multiword DMA active and modes supported (see note following this table) xx07H 64 Advanced PIO modes supported (modes 3 and 4 supported) 0003H 65 Minimum multiword DMA transfer cycle time per word (120 ns) 0078H 66 Recommended multiword DMA transfer cycle time per word (120 ns) 0078H 67 Minimum PIO cycle time without IORDY flow control (240 ns) 0078H 68 Minimum PIO cycle time with IORDY flow control (120 ns) 0078H 69–74 ATA-reserved 0000H 75 Queue depth 001FH 76 Serial ATA capabilities 0D06H 77 ATA-reserved 0000H 78 Serial ATA features supported 0048H 79 Serial ATA features enabled 0048H 80 Major version number 01F0H 81 Minor version number 0029H 82 Command sets supported 746BH 83 Command sets supported 7D69H 84 Command sets support extension 61E3H 85 Command sets enabled 7469 86 Command sets enabled BC49H 87 Command sets enable extension 61E3H 88 Ultra DMA support and current mode (see note following this table) xx7FH 89 Security erase time xxxxH 90 Enhanced security erase time xxxxH 91 Current APM values 8080H 92 Master password revision code FFFEH 93 Hardware reset value (see description following this table) xxxxH 94 Auto acoustic management setting xxxxH 95 Stream Min. Request Size 0000H 96 Streaming Transfer Time - DMA 0000H 97 Streaming Access Latency - DMA and PIO 0000H 98-99 Streaming Performance Granularity 0000H Seagate Video 2.5 HDD Product Manual, Rev. E 23 Serial ATA (SATA) Interface Table 10 Identify Device command Word Description Value 100–103 Total number of user-addressable LBA sectors available (see Section 3.2 for related information) These words are required for drives that support the 48-bit addressing feature. Maximum value: 0000FFFFFFFFFFFFh. ST500VT000 = 976,773,168 ST500VT001 = 976,773,168 ST320VT000 = 625,142,448 ST250VT000 = 488,397,168 104 Streaming Transfer Time - PIO 0000H 105 Reserved 0000H 106 Physical sector size / Logical sector size 6003H 107 Seagate reserved 0000H 108-111 The mandatory value of the world wide name (WWN) for the drive. NOTE: This field is valid if word 84, bit 8 is set to 1 indicating 64-bit WWN support. Each drive will have a unique value. 112-118 ATA-reserved 0000H 119 Free Fall Protection support (bit 5) 1 = Free Fall Protection supported 0 = Free Fall Protection not supported 120 Free Fall Protection enable/disable (bit 5) 1 = Free Fall Protection feature is enabled 0 = Free Fall Protection feature is disabled 121–127 ATA-reserved 0000H 128 Security status 0021H 129–159 Seagate-reserved xxxxH 160–221 ATA-reserved 0000H 222 Transport major version number 101FH 223–254 ATA-reserved 0000H 255 Integrity word xxA5H Note See the bit descriptions below for words 63, 88 and 93 of the Identify Drive data. (on next page) Seagate Video 2.5 HDD Product Manual, Rev. E 24 Serial ATA (SATA) Interface Table 11 Bit Descriptions Description (if bit is set to 1) Bit Word 63 0 Multiword DMA mode 0 is supported. 1 Multiword DMA mode 1 is supported. 2 Multiword DMA mode 2 is supported. 8 Multiword DMA mode 0 is currently active. 9 Multiword DMA mode 1 is currently active. 10 Multiword DMA mode 2 is currently active. Bit Word 88 0 Ultra DMA mode 0 is supported. 1 Ultra DMA mode 1 is supported. 2 Ultra DMA mode 2 is supported. 3 Ultra DMA mode 3 is supported. 4 Ultra DMA mode 4 is supported. 5 Ultra DMA mode 5 is supported. 6 Ultra DMA mode 6 is supported. 8 Ultra DMA mode 0 is currently active. 9 Ultra DMA mode 1 is currently active. 10 Ultra DMA mode 2 is currently active. 11 Ultra DMA mode 3 is currently active. 12 Ultra DMA mode 4 is currently active. 13 Ultra DMA mode 5 is currently active. 14 Ultra DMA mode 6 is currently active. Bit Word 93 13 1 = 80-conductor cable detected, CBLID above VIH 0 = 40-conductor cable detected, CBLID below VIL Seagate Video 2.5 HDD Product Manual, Rev. E 25 Serial ATA (SATA) Interface 4.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the Features register are defined as follows: Table 12 Set Features command values 02H Enable write cache (default). 03H Set transfer mode (based on value in Sector Count register). Sector Count register values: 00H Set PIO mode to default (PIO mode 2). 01H Set PIO mode to default and disable IORDY (PIO mode 2). 08H PIO mode 0 09H PIO mode 1 0AH PIO mode 2 0BH PIO mode 3 0CH PIO mode 4 (default) 20H Multiword DMA mode 0 21H Multiword DMA mode 1 22H Multiword DMA mode 2 40H Ultra DMA mode 0 41H Ultra DMA mode 1 42H Ultra DMA mode 2 43H Ultra DMA mode 3 44H Ultra DMA mode 4 45H Ultra DMA mode 5 46H Ultra DMA mode 6 55H Disable read look-ahead (read cache) feature. 82H Disable write cache AAH Enable read look-ahead (read cache) feature (default). C1H Disable the Free Fall Protection feature (41H above enables the Free Fall Protection feature) F1H Report full capacity available Note At power-on, or after a hardware or software reset, the default values of the features are as indicated above Seagate Video 2.5 HDD Product Manual, Rev. E 26 Serial ATA (SATA) Interface 4.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T. commands and implementation, see the Draft ATA-5 Standard. SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4H) that eliminates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at: http://www.seagate.com/support/downloads/seatools/. This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that supports S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the drive uses. Table 13 S.M.A.R.T. Commands Code in features register S.M.A.R.T. command D0H S.M.A.R.T. Read Data D2H S.M.A.R.T. Enable/Disable Attribute Autosave D3H S.M.A.R.T. Save Attribute Values D4H S.M.A.R.T. Execute Off-line Immediate (runs DST) D5H S.M.A.R.T. Read Log Sector D6H S.M.A.R.T. Write Log Sector D8H S.M.A.R.T. Enable Operations D9H S.M.A.R.T. Disable Operations DAH S.M.A.R.T. Return Status Note If an appropriate code is not written to the Features Register, the command is aborted and 0x 04 (abort) is written to the Error register. Seagate Video 2.5 HDD Product Manual, Rev. E 27 Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000 ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888 EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00 Publication Number: 100713733, Rev. E April 2016