Transcript
QUICK START GUIDE
NWKED
VIDEO ENCODER/DECODER KIT FOR USE WITH NETWAVE WIRELESS ETHERNET
This manual serves the following ComNet Model Number: NWKED
Thank you for purchasing NetWave® from ComNet. This quick start guide is designed to walk you through installation. This guide applies to the following models: NWKED: Analog Video Encoder/Decoder Kit for use with NetWave Wireless Ethernet See Figures 1 through 4 for Installation instructions.
INS_NWKED_QS_REV– 05/20/13 PAGE 1
QUICK START USER GUIDE
NWKED
FIGURE 1 – NWKED ENCODER
FIGURE 2 – NWKED DECODER
TECH SUPPORT: 1.888.678.9427
INS_NWKED_QS_REV– 05/20/13 PAGE 2
QUICK START USER GUIDE
NWKED
FIGURE 3 – INSTALLATION INSTRUCTIONS Step 1. Unpack the hardware from the box. Instructions for the Decoder and the Encoder are the same.
Step 2. A. Connect the Power Adapter with the Terminal Block B. Connect the Terminal Block to the power port on the device
Step 3. Connect the video source to BNC Port on the Encoder. Press and twist the BNC connector to ensure a secure fit. Connect the Coaxial cable from the receiver to the composite port on the Decoder. Press and twist the BNC connector to ensure a secure fit. Step 4. A. Connect one end of an RJ-45 Ethernet cable to the OUT port of the Power Injection Module (PIM) and the other end to LAN of the access point. Maximum length of the RJ-45 CAT5 cable is 100 meters. B. Connect the RJ-45 Ethernet cable attached to the PIM to the Encoder/Decoder. C. Connect the power adaptor to the main electrical supply and the power plug into the socket of the PIM.
D
PoE power input: Passive PoE (range 12 to 24 VDC) D. Connect the RJ-45 cable from Port 2 on the access point to an external PoE device, typically a camera as shown. E. A Drip Loop is recommended as additional precaution against moisture.
B
A
E
C
E
E
TECH SUPPORT: 1.888.678.9427
INS_NWKED_QS_REV– 05/20/13 PAGE 3
QUICK START USER GUIDE
NWKED
INSTALLATION REQUIREMENTS Shielded outdoor CAT 5 or better should be used for all out of plant Ethernet connection and should be properly grounded through the PoE AC ground. Industrial grade shielded Ethernet cable is recommended to help prevent ESD damage commonly experienced with outdoor installations. Visit www.comnet.net/comnet-products/cables
CONFIGURING NETWAVE 1. Connect an Ethernet cable from the port labelled as Ethernet on the Encoder or Decoder to either a laptop or a PC LAN port. 2. Connect the terminal block the provided power supply and connect to the Encoder/Decoder. Connect the power supply to a power outlet. You should notice the red PWD LED illuminate. 3. Set the IP address of the laptop being used to configure Netwave to static and the subnet to 192.168.10.x/24 subnet. 4. Point the browser to the Encoder/Decoder IP address. The default addresses are: Decoder: 192.168.10.200 Encoder: 192.168.10.201 NOTE: Internet Explorer 11 in Compatibility mode is highly recommended. 5. A login prompt will pop up. Enter: ID: admin Password: 123456 6. To configure the Decoder login then Select Connection Settings and set the desired settings. • Select Apply Settings • Select Save • Select Reboot to store settings. 7. To configure the Encoder login then Select the Setup Tab and make the necessary changes. • Select Apply Settings • Select Save • Select Reboot to store settings.
DEFAULT CONFIGURATIONS IP Address of Decoder Web Server 192.168.10.200
Connection Type TCP
IP Address of Encoder Web Server 192.168.10.201
Enable Audio In Off
LAN Mode for Web Server
Enable Control Data
Static Addressing
On
Web Server User ID admin
Stream Port
Web Server Password 123456
Control Port 6001
6002
Video Stream MPEG4 NOTE: A Reset to defaults (performed on the ADMIN page) will erase all user configurations.
FIGURE 4 – TYPICAL APPLICATION
LEGEND
10/100 Ethernet
WIRELESS
10/100 Ethernet
Video
CAT5 COAX
Monitor
Decoder
TECH SUPPORT: 1.888.678.9427
NW1 Access Point (not included)
NW1 Client (not included)
Encoder
Camera
ETHERNET VIDEO
INS_NWKED_QS_REV– 05/20/13 PAGE 4
QUICK START USER GUIDE
NWKED
Need Additional Assistance? Visit our website http://www.comnet.net or contact Comnet tech support: Tel: (203) 796-5300 Toll free: (888) 678-9427 Email:
[email protected] Additional Technical support contact details can be found at: http://www.comnet.net/services/technical-support.html Or Visit our pre-sales design center: http://www.comnet.net/services/design-center.html Or our customer care: http://www.comnet.net/services/customer-care.html Additional Downloads Datasheets, Installation manuals and other product documentation can be found at: http://www.comnet.net/comnet-products/ethernet/wireless/
3 CORPORATE DRIVE | DANBURY, CT 06810 | USA T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 |
[email protected] 8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE T: +44 (0)113 307 6400 | F: +44 (0)113 253 7462 |
[email protected] © 2014 Communications Networks Corporation. All Rights Reserved. “ComNet,” the “ComNet Logo,” “NetWave,” and the “NetWave Logo” are registered trademarks of Communication Networks, LLC. INS_NWKED_QS_REV– 05/20/13 PAGE 5
