Transcript
Video Extender Category 5 UTP VGA/Multisync Video Extender
Installation Manual ST121UTP
1 Overview The ST121UTP Video Extender allows you to extend the distance between the computer system unit and the display monitor by up to 130 meters (430 feet). This is accomplished with a local transmitting unit and a remote receiving unit. The St121UTP is ideal for factory and construction sites, or in any installation where the display needs to reside in a harsh setting but you want the system equipment kept in an enviromentally friendly location.
Features • Extends video cables by up to 130m (430') • Consists of 1 Base unit for the local display, and 1 Remote unit for the remote display • Uses standard Category 5 straight-wired, twisted-pair, network patch cable for economical and reliable data transmission • Provides crystal clear picture quality • 212MHz VGA bandwidth allows resolutions of up to 1600x1200 @ 85Hz refresh rate • Supports VGA, SVGA, and Multisync monitors • Includes VGA extension cable to connect the Base unit to the computer, and AC power adapters • No software required
Specifications Connectors
Local Unit
Remote Unit
Input
High Density DB15 Male
RJ45 Female
Output
High Density DB15 Female, RJ45 Female
High Density DB15 Female
LEDs
Power
VGA Resolution
640x480@60Hz to 130m (430’), 1600x1200@85Hz to 80m (262’)
Signal Type
VGA, SVGA, Multisync
Cable Type
Category 5 shielded twisted pair (STP)
Max. Cable Distance
130m (430’)
Weight
240g
Dimensions
119x86x58mm (4.7x3.4x3.1")
Power Consumption
AC 9V 130mA (max.)
Certifications
CE Mark, FCC Part 15
235g
AC 9V 180mA (max.)
Getting Started This section is designed to help you prepare the ST121UTP for installation. Please read through this section carefully before attempting to install the card.
2 Unpacking the ST121UTP This package should contain: 1 x Remote unit ST121UTP 1 x Local Unit ST121UTP 2 x 9V AC adapter
Installation UTP VGA Video Extender
1
Long
2
To Remote Unit
3
AC 9V
4
Short
ST121UTP
Local Unit
Monitor
5
For PC
6
Power
UTP VGA Video Extender
ST121UTP
Remote Unit
1
To Remote Unit
2
AC 9V
3
Local Unit 1. Range Switch 2. Remote I/O connector 3. AC 9V Power Jack 4. Power LED 5. Monitor connector 6. PC connector
Monitor
4
Remote Unit 1. Remote I/O connector 2. AC 9V Power jack 3. Power LED 4. Monitor connector
Power
1. Make sure that the computer and monitors you are using for the installation are all powered off. 2. Plug the male end of a male to female VGA extension cable into the computer’s video output port; plug the female end of the cable into the Local unit’s PC port. 3. Plug the local monitor’s VGA cable into the Local unit’s Monitor port. 4. Plug one end of the power adapters into an AC source; plug the adapter’s power cable into the Local unit’s AC 9V power jack. 5. Plug one end of the Category 5 twisted pair cable into the Local unit’s Remote I/O port. 6. Slide the Range Switch to the Long position if the Remote unit is located a long distance away; slide the switch to the Short position if the Remote unit is located a short distance away. 8. Plug the remote monitor’s VGA cable into the Remote unit’s Monitor port. 9. Plug the second power adapter into an AC source; plug the adapter’s power cable into the Remote unit’s AC 9V power jack. 10. Power on the computer and monitors.
3 Troubleshooting No Video: Make sure that all cables are securely plugged into their sockets.
Technical Details Cable Length Table Resolution 640 x 480
Distance (m) @ 60 Hz
@ 75 Hz
130
800 x 600
100
1024 x 768
100
1280 x 1024 1600 x 1200
@ 85 Hz 100
100 100
80
TP Pin Assignment Pin
Assignment
1
V OUT G
2
/V OUT G
3
V OUT B
4
V OUT R
5
/V OUT R
6
/V OUT B
7
GND
8
GND
TP Wiring Diagram Pair 3 Pair 2
Pair 1
Pair 4
1 2 3 4 5 6 7 8 W-G
G W-O
BL W-BL O W-BR BR
Jack Positions
