Video Wall Solution (22~82 Inches)

Transcript

Installation and User's Guide VIDEO WALL SOLUTION (22~82 inches) All contents of this document may change without prior notice, and actual product appearance may differ from that depicted herein Installation and User's Guide 1. SAFETY INSTRUCTION Follow this safety instruction to use the monitor properly and prevent the damages. This safety instruction has “Warning” & “Caution” as below Warning - If the user does not follow this instruction, it may cause the serious damage to the user. Caution - If the user does not follow this instruction, it may cause the slight damage to the user or cause some damages to the monitor. Keep this user’s guide book for later use. Warning Never remove the back over and touch the inside of the monitor. If you need a service, please contact the service center. Never push objects of any kind into this product as they may result in a risk of fire or electric shock. Keep away the monitor from the direct sunlight and a heating appliance. Connect the power code to the wall outlet tightly. If the power code or plug are defective and the wall outlet is not tight, please do not use them. 2 Installation and User's Guide Warning Do not install this monitor on the outside and near water. If may cause damage to the product, electric shock and fire. For cleaning do not use liquid cleaners. Never touch the power plug with wet-hands. When lightning and thundering, unplug the monitor from the wall outlet and never touch it. Unplug this product from the wall outlet, when It does not operate for a long time. When smoking and noising from the monitor, unplug the product from the wall outlet and contact a service center. WA R N I N G : How to fix Do not open this product as it contains high voltage inside. It may create an electric shock. It the user disassembles and remove the back cover, it does not make sure to make up for the damages and do a service and exchange the monitor. 3 Installation and User's Guide Cautions Install this monitor some distance From the wall and do not install unless Proper ventilation is provided. Place this product on a stable place. If not, it may fall, causing serious Damages to the monitor and people. The openings must not be blocked by curtain, rug or other similar surface. When carrying this monitor, be careful not to damage the panel and drop it It may cause some trouble. Before carrying the monitor, tum it off and Unplug the signal cables and the power code From the wall outlet. Take the power plug out from the wall outlet. Do not pull the cable. It may snap the innerwires and cause overheating and fire. 4 Installation and User's Guide Cautions Install this monitor about 50cm far from the eyes and an angle of 0~15 degrees below eyes. Too close installation may cause having weak sight. Do not press the LCD panel with hands or the sharpened material hardly. For cleaning, unplug the monitor from the Wall outlet. Do net use the liquid cloth. Use the soft cloth. Do not use the chemical liquid for cleaning. It may cause fading and breakage. WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR WATER. Instructions for Disposal of Electrical and Electronic Equipment in Private Households Disposal of used Electrical and Electronic Equipment (Applicable in the European Union and other European countries with garbage separate disposal and collection methods) This symbol on the product, or in the related documents in the package, indicates that this product shall not be treated as normal household waste. Instead, it should be taken to a proper applicable collection point or depot for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent possible negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local city authority, your household waste disposal service or the place where you purchased the product. 5 Installation and User's Guide 2. FCC RF INTERFERENCE STATEMENT NOTE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio, TV technician for help. ● Only shielded interface cable should be used. Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment. DOC COMPLIANCE NOTICE This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the radio interference regulation of Canadian Department of communications. 6 Installation and User's Guide TABLE OF CONTENTS 1. SAFETY INSTRUCTION 1-1 Warning 1-2 Caution 2 2. FCC STATEMENT 6 3. INSTALLATION 3-1 Parts 3-2 How to Install 8 4. OSD MENU SETTING 4-1 Mode Setting 4-2 Menu Setting 13 5. FEATURES 21 6. MECHANICAL DRAWING 22 7. TROUBLESHOOTING 23 7 Installation and User's Guide 3. INSTALLATION 3-1 Parts LCD Monitor & Keypad Joint Bracket UTP Cable VGA Cable Serial Cable Trigger Cable (Only 40 inches or more) Power Cable Remote Controller Battery Install CD User Manual 8 Installation and User's Guide 3-2 How to Install KEYPAD CONTROLLER This KEYPAD is attached to a magnet, so you can freely paste UTP Cable (1.5m) If you want to replace with a longer cable Please purchase separately SHORT KEY FUNCTION OSD KEY FUNCTION On/off the OSD menu or exit the source selection menu Move the cursor to choose on the OSD menu Select the source on the INPUT menu Move up the cursor to choose on the OSD menu Activate the auto adjustment of RGB source Control down on the OSD menu or move to the previous menu Volume down Select the OSD menu Control up on the OSD menu Volume up Turn the power ON or OFF. There will be a few seconds delay before the display appears. The power LED (next to the power switch) lights with green when the power is turned ON. The power is turned off by pressing the power switch again and the power LED goes red. 9 Installation and User's Guide CONNECTION 22 inches 1 2 3 4 5 6 1 2 3 4 5 6 14 40~82 inches 7 8 9 10 11 12 1 HDMI HDMI Signal input / loop output 8 VIDEO-2 IN / OUT VIDEO-2 Signal input / loop output 2 DVI DVI Signal input / loop output 9 AUDIO (VIDEO-1) Stereo audio input for VIDEO-1 3 VGA VGA (PC RGB) Signal input / loop output 10 AUDIO (VIDEO-2) Stereo audio input for VIDEO-2 4 RS-232 IN / OUT SERIAL Cable input / output for RS-232 11 TRIGGER TRIGGER Signal input 5 KEYPAD UTP Cable input for KEYPAD 12 SPEAKER OUT Stereo speaker output 6 AUDIO (PC) Stereo audio input for VGA 13 AC POWER AC 100-240V input 7 VIDEO-1 IN / OUT VIDEO-1 Signal input / loop output 14 DC24V DC 24V (Adapter) input 13 10 Installation and User's Guide CONFIGURE THE VIDEO WALL 1. You can combine two or more monitors, and configure the VIDEO WALL. 2. If you want to configure VIDEO WALL, please contact your dealer or a professional installer. 3. JOINT BRACKET helps to easily adjust the VIDEO WALL. (Supplied with monitor) SIDE Assemble the JOINT BRACKET using two M4 screws. CENTER Assemble the JOINT BRACKET using four M4 screws. CABLES CONNECTION * Cable connection order, it may be different from the order of the 'SET ID' or 'SEQUENCE' (Refer to page 15~17) OR ONIT 1st M OR ONIT 2nd M OR ONIT 3rd M OR ONIT 4th M HDMI OUT HDMI IN DVI OUT DVI IN VGA OUT VGA IN RS-232 OUT RS-232 IN VIDEO1 OUT VIDEO1 IN VIDEO2 OUT VIDEO2 IN * Please install the VWCP (Video Wall Control Program) for remote control of the monitors through the computer. For information about installing and using VWCP, please refer to the installation disk that came with the monitor. 11 Installation and User's Guide REMOTE CONTROLLER A POWER MUTE VIDEO1 VIDEO2 VGA AUTO DVI HDMI A MODE SELECT MENU VIDEO 1 (Only 40 inches or more) Select VIDEO 1 mode VIDEO 2 (Only 40 inches or more) Select VIDEO 2 mode DVI Select DVI mode VGA (RGB) Select VGA mode HDMI Select HDMI mode COLOR TEMP S.SET SCAN MODE B VOL- VOL+ MENU/EXIT C B PIP KEY LOCK P.INPUT P.LOCATION P.SWAP STILL P.SIZE OSD CONTROL MENU POWER Turn ON / OFF the monitor MUTE Turn ON / OFF the sound AUTO Auto adjust position of the screen (in VGA mode) COLOR TEMPERATURE Select color temperature of the screen SCAN MODE Select the scan mode of the screen VOL- / VOL+ Increase / Decrease the volume level MENU / EXIT Activate and exit the OSD menu KEY LOCK Locking the button (Prevent operation) STILL Freeze the current image C PIP CONTROL MENU S. SET Select between main and PIP audio input PIP Activates PIP/PBP mode P. INPUT Select an input source for PIP mode P. LOCATION Select a location for PIP mode P. SIZE Select a size for PIP mode P. SWAP Swap between main and PIP input 12 Installation and User's Guide 4. OSD MENU SETTING 4-1 Mode Setting INPUT VIDEO1 VIDEO2 √RGB PC DVI HDMI 1. Use Source button and then ▲ or ▼ button to move the source. 2. Press the ► button to select the source. 3. Press the MENU/EXIT button to exit the INPUT menu. ▼/▲:MOVE ▶:ENTER VIDEO1 Select VIDEO1 Mode (Only 40 inches or more) VIDEO2 Select VIDEO2 Mode (Only 40 inches or more) RGB PC Select VGA Mode DVI Select DVI Mode HDMI Select HDMI mode 13 Installation and User's Guide 4-2 Menu Setting PICTURE PICTURE PICTURE CONTRAST BRIGHTNESS COLOR TINT SHARPNESS PEAKING CONTROL COLOR TEMP RED GREEN BLUE SCREEN SETUP RGB SETUP 60% 50% 50% 50% 50% 50% ◀ 1. Press the MENU key to access menu. 2. Use the ▲ or ▼ key to choose PICTURE. 3. Press the ► key to enter the PICTURE menu. 4. Use the ▲ or ▼ key to choose an item of PICTURE. 5. Use the ◄ or ► key to adjust the setting on a selected item. ▶ MEDIUM 128 128 128 CYCLE SETUP TRIGGER ▼/▲ : MOVE ◀/▶ : ADJUST ITEM ▶ : ENTER MENU : EXIT VER : *.* FUNCTION DEFAULT VALUE AVAILABLE MODE CONTRAST Adjust the contrast level of color 60% All modes BRIGHTNESS Adjust the brightness level of color 50% All modes COLOR Adjust the depth of color 50% VIDEO, HDMI TINT Adjust the tint of color (only NTSC signal) 50% VIDEO, HDMI SHARPNESS Adjust the sharpness of picture 50% VIDEO, HDMI PEAKING CONTROL Adjust the sharpness of outline 50% HDMI COLOR TEMP Set the color temperature of screen (MEDIUM, WARM, USER, COOL) MEDIUM All modes 14 Installation and User's Guide SCREEN PICTURE SCREEN SETUP RGB SETUP CYCLE SETUP SCREEN H MONITORS V MONITORS SEQUENCE H GAP V GAP SCAN MODE PIP PIP INPUT PIP SWAP PIP SIZE PIP LOCATION ◀ ◀ ◀ ◀ ◀ ◀ ◀ ◀ ▶ ◀ ◀ 01 01 01 00 00 FULL OFF VIDEO2 ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ SMALL R/B ▶ ▶ 1. Press the MENU key to access menu. 2. Use the ▲ or ▼ key to choose SCREEN. 3. Press the ► key to enter the SCREEN menu. 4. Use the ▲ or ▼ key to choose an item of SCREEN. 5. Use the ◄ or ► key to adjust the setting on a selected item. TRIGGER ▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT ITEM VER : *.* FUNCTION DEFAULT VALUE AVAILABLE MODE H MONITORS Set the total number of horizontally installed monitors on the video wall situation (01 ~ 99) 01 All modes V MONITORS Set the total number of vertically installed monitors on the video wall situation (01 ~ 99) 01 All modes SEQUENCE Set the sequence of installed monitors on the video wall situation (01 ~ 99) 01 All modes H GAP Set the horizontal gap between adjacent panels caused by bezel width (00 ~ 99) 00 All modes V GAP Set the vertical gap between adjacent panels caused by bezel width (00 ~ 99) 00 All modes SCAN MODE Select the scan mode of the screen (FULL, REAL,*UNDER, OVER, 4:3) FULL All modes PIP Activate PIP/PBP mode (OFF, ON, DW1, DW2) (Only 40 inches or more) OFF HDMI *UNDER : It does not appear in HDMI mode 15 Installation and User's Guide ex) In case of 3X2 Video Wall Setting 1 5 9 13 2 6 10 14 3 7 11 15 4 8 12 16 V GAP : 01 SEQUENCE numerical order H MONITORS : 03 V MONITORS : 02 SEQUENCE : 01 H MONITORS : 03 V MONITORS : 02 SEQUENCE : 02 H MONITORS : 03 V MONITORS : 02 SEQUENCE : 03 H MONITORS : 03 V MONITORS : 02 SEQUENCE : 04 H MONITORS : 03 V MONITORS : 02 SEQUENCE : 05 H MONITORS : 03 V MONITORS : 02 SEQUENCE : 06 H GAP : 01 SCAN MODE REAL : Display original images entered from the source intactly UNDER : Display the image on the smaller area than the screen Original image is fully displayed. OVER : Display the image on the broader area than the screen Original Image is cut off on the edge. 4:3 : Display the image to 4:3 aspect ratio PIP Default Setting is OFF and changeable to ON, DW1 and DW2 PIP/PBP modes. OFF : PIP/PBP modes are not activated. ON : Switch on PIP/PBP mode DW1 : change to Double Window mode 1 DW2 : change to Double Window mode 2 After selecting PIP/PBP modes, following items are activated. PIP INPUT : Select an input source for PIP image (VIDEO 1, VIDEO 2) PIP SWAP : Swap main picture and sub picture PIP SIZE : Select the size of PIP image (SMALL, NORMAL, LARGE) PIP LOCATION : Select the position of PIP image (R/B, L/B) 16 Installation and User's Guide SETUP SETUP PICTURE SCREEN SETUP RGB SETUP CYCLE SETUP TRIGGER INPUT LANGUAGE AUDIO MUTE AUDIO OUT NOISE REDUCTION OSD TIME DEFAULT SET ID KEY LOCK LINE SHIFT FAN CONTROL FAN AUTO REF FAN SPEED CURRENT TEMP ▼/▲ : MOVE ◀/▶ : ADJUST ITEM ◀ ◀ ◀ ◀ ◀ VIDEO1 ENGLISH OFF INTERNAL ON ▶ ▶ ▶ ▶ ▶ ▶ ◀ ◀ ◀ ◀ 01 OFF OFF AUTO ▶ ▶ ▶ ▶ ◀ NORMAL ▶ 15s 1. Press the MENU key to access menu. 2. Use the ▲ or ▼ key to choose SETUP. 3. Press the ► key to enter the SETUP menu. 4. Use the ▲ or ▼ key to choose an item of SETUP. 5. Use the ◄ or ► key to adjust the setting on a selected item. 42c 42c ▶ : ENTER MENU : EXIT VER : *.* FUNCTION DEFAULT VALUE AVAILABLE MODE INPUT Select the input source for main picture LANGUAGE Set the language of OSD (ENGLISH, ITALIAN, FRENCH, SPANISH, GERMAN) ENGLISH All modes AUDIO MUTE Turn on/off the audio output OFF All modes AUDIO OUT Select the speaker for audio output (INTERNAL, EXTERNAL) INTERNAL All modes NOISE REDUCTION Set the noise reduction mode ON All modes OSD TIME Set the time duration of OSD menu (5~30s) 15s (seconds) All modes DEFAULT Factory default setting SET ID Allocate an ID of the set for RS-232 control 01 All modes KEY LOCK Lock the key action (Prevent operation) OFF All modes LINE SHIFT Move the image a little instantaneously to protect the screen OFF All modes FAN CONTROL Select the control method of FAN (AUTO, ON, OFF) AUTO All modes FAN AUTO REF Set the reference temperature for automatic FAN control (20~60c) 42c (celsius) All modes FAN SPEED Select the speed of FAN (NORMAL, FAST, SLOW) NORMAL All modes CURRENT TEMP Display the current temperature All modes All modes All modes 17 Installation and User's Guide To cancel KEY LOCK mode Remote Controller : Press KEY LOCK button Keypad : Press ▲ & ◄ buttons simultaneously RGB SETUP (ONLY RGB PC MODE) RGB SETUP PICTURE H-POSITION V-POSITION CLOCK PHASE AUTO ADJUST POWER SAVING AUTO REPEAT SCREEN SETUP RGB SETUP 100% 0% 0% 0% ▶ ◀ ◀ ▶ ▶ OFF OFF 1. Press the MENU key to access menu. 2. Use the ▲ or ▼ key to choose RGB SETUP. 3. Press the ► key to enter the RGB SETUP menu. 4. Use the ▲ or ▼ key to choose an item of RGB SETUP. 5. Use the ◄ or ► key to adjust the setting on a selected item. CYCLE SETUP TRIGGER ▼/▲ : MOVE ◀/▶ : ADJUST ITEM ▶ : ENTER MENU : EXIT VER : *.* FUNCTION DEFAULT VALUE AVAILABLE MODE H-POSITION Adjust the horizontal position of the screen RGB PC V-POSITION Adjust the vertical position of the screen RGB PC CLOCK Adjust the clock of the screen RGB PC PHASE Adjust the phase of the screen RGB PC AUTO ADJUST Adjust all of above items for suitable screen RGB PC POWER SAVING Adjust the power saving mode OFF RGB PC AUTO REPEAT Repeat AUTO ADJUST action automatically OFF RGB PC 18 Installation and User's Guide CYCLE SETUP (ONLY 40 INCHES OR MORE) CYCLE SETUP PICTURE CYCLE TIME CYCLE VIDEO1 VIDEO2 RGB PC DVI HDMI SCREEN SETUP RGB SETUP 10s ◀ ◀ ◀ ◀ ◀ ◀ ▶ ▶ ▶ ▶ ▶ ▶ OFF OFF OFF OFF OFF OFF 1. Press the MENU key to access menu. 2. Use the ▲ or ▼ key to choose CYCLE SETUP. 3. Press the ► key to enter the CYCLE SETUP menu. 4. Use the ▲ or ▼ key to choose an item of CYCLE SETUP. 5. Use the ◄ or ► key to adjust the setting on a selected item. CYCLE SETUP TRIGGER ▼/▲ : MOVE ITEM ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : *.* FUNCTION DEFAULT VALUE AVAILABLE MODE CYCLE TIME Adjust the time interval to display selected mode 10s (seconds) All modes CYCLE Display selected modes sequentially in set cycle time OFF All modes VIDEO1 Choice as to whether to cycle of VIDEO1 mode OFF All modes VIDEO1 Choice as to whether to cycle of VIDEO2 mode OFF All modes RGB PC Choice as to whether to cycle of RGB PC mode OFF All modes DVI Choice as to whether to cycle of DVI mode OFF All modes HDMI Choice as to whether to cycle of HDMI mode OFF All modes 19 Installation and User's Guide TRIGGER (ONLY 40 INCHES OR MORE) TRIGGER PICTURE TRIGGER MODE TRIGGER INPUT TRIGGER DWELL SCREEN ◀ ◀ ▶ ▶ OFF VIDEO1 10s SETUP 1. Press the MENU key to access menu. 2. Use the ▲ or ▼ key to choose TRIGGER. 3. Press the ► key to enter the TRIGGER menu. 4. Use the ▲ or ▼ key to choose an item of TRIGGER. 5. Use the ◄ or ► key to adjust the setting on a selected item. RGB SETUP CYCLE SETUP TRIGGER ▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT ITEM VER : *.* FUNCTION DEFAULT VALUE AVAILABLE MODE TRIGGER MODE Set the trigger mode OFF All modes TRIGGER INPUT Select the input source of trigger mode (VIDEO1, VIDEO2) VIDEO1 All modes TRIGGER DWELL Set the display time of trigger mode (10~60s) 10s (seconds) All modes INPUT SIGNAL MODE TABLE INPUT SIGNAL VGA / DVI HDMI MODE RESOLUTION VERTICAL FREQUENCY (Hz) VGA 640X480 60 / 72 / 75 VGA 720X400 70 SVGA 800X600 56 / 60 / 75 XGA 1024X768 60 / 75 SXGA- 1280X960 60 SXGA 1280X1024 60 / 75 WXGA 1366X768 60 WXGA+ 1440X900 60 FHD 1920X1080 60 SDTV 480i 720X480 30 SDTV 576i 720X576 25 EDTV 480p 720X480 60 EDTV 576p 720X576 50 HDTV 720p 1280X720 50 / 60 HDTV 1080i 1920X1080 25 / 30 HDTV 1080p 1920X1080 50 / 60 20 Installation and User's Guide 5. FEATURE Bezel Width Display Interface RNK22SNH RNK40NHF RNK46NHF RNK46SHF RNK55NHF RNK55SNF RNK82NNF Outside to BEZEL 5.7 mm (Two Sides) 13.0 mm 15.5 mm 5.7 mm (Two Sides) 15.5 mm 5.7 mm (Two Sides) 23.5~34.0 mm Outside to Active Area 5.9 mm (Two Sides) 14.2 mm 17.5 mm 5.9 mm (Two Sides) 17.5 mm 5.9 mm (Two Sides) 26.3~36.3 mm Screen Size 21.6 inches 40.0 inches 46.0 inches 46.0 inches 54.6 inches 54.6 inches 81.6 inches Resolution 960*960 pixels 1920*1080 pixels 1920*1080 pixels 1920*1080 pixels 1920*1080 pixels 1920*1080 pixels 1920*1080 pixels Pixel Pitch 0.135*0.135 mm 0.461*0.461 mm 0.530*0.530 mm 0.530*0.530 mm 0.630*0.630 mm 0.630*0.630 mm 0.941*0.941 mm Brightness 450 cd/m^2 700 cd/m^2 700 cd/m^2 700 cd/m^2 700 cd/m^2 450 cd/m^2 450 cd/m^2 Contrast Ratio 4000:1 3000:1 3000:1 3500:1 4000:1 3500:1 5000:1 Aspect Ratio 1:1 (Mosaic) 16:9 16:9 16:9 16:9 16:9 16:9 Viewing Angle (H/V) 178/178 degrees 178/178 degrees 178/178 degrees 178/178 degrees 178/178 degrees 178/178 degrees 178/178 degrees 16.7 million Display Color 16.7 million 16.7 million 16.7 million 16.7 million 16.7 million 16.7 million Response Time 8 ms 8 ms 8 ms 8 ms 8 ms 8 ms 8 ms Video System NTSC/PAL NTSC/PAL NTSC/PAL NTSC/PAL NTSC/PAL NTSC/PAL NTSC/PAL 50,000 hours Panel Life Time 50,000 hours 50,000 hours 50,000 hours 50,000 hours 50,000 hours 50,000 hours Video In/Out (BNC Type) N/A 2/2 2/2 2/2 2/2 2/2 2/2 VGA In/Out (15Pin D-Sub) 1/1 1/1 1/1 1/1 1/1 1/1 1/1 DVI In/Out 1/1 1/1 1/1 1/1 1/1 1/1 1/1 HDMI In/Out 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 RS-232 In/Out 1/1 1/1 1/1 1/1 1/1 1/1 Audio In (RCA Type) N/A 2 2 2 2 2 2 PC Stereo In 1 1 1 1 1 1 1 Built in Speakers Y (1W*2) Y (7.5W*2) Y (7.5W*2) Y (7.5W*2) Y (7.5W*2) Y (7.5W*2) Y (7.5W*2) Remote Control Y Y Y Y Y Y Y RS-232 Control Special Features Dimension Cabinet Circumstance Mounts Monitor OSD & Multi Vision Monitor OSD & Multi Vision Monitor OSD & Multi Vision Multi Display Function PIP/PBP PIP/PBP PIP/PBP PIP/PBP PIP/PBP PIP/PBP PIP/PBP Filter Type 3D Comb Filter 3D Comb Filter 3D Comb Filter 3D Comb Filter 3D Comb Filter 3D Comb Filter 3D Comb Filter Deinterlacing Y Y Y Y Y Y Y Auto Pixel Shift Y Y Y Y Y Y Y FAN On/Off Conrol N/A Y Y Y Y Y Y Temperature Sensor N/A Y Y Y Y Y Y Y One Stretch Image by Edge Set Y Y Y Y Y Y Trigger Source Switching N/A Y Y Y Y Y Y Noise reduction Y Y Y Y Y Y Y Auto source sequencing Y Y Y Y Y Y Y Multi Lingual Language Eng, Spa, Fre, Ger, Ita Eng, Spa, Fre, Ger, Ita Eng, Spa, Fre, Ger, Ita Eng, Spa, Fre, Ger, Ita Eng, Spa, Fre, Ger, Ita Eng, Spa, Fre, Ger, Ita Eng, Spa, Fre, Ger, Ita 15.48*15.48*3.94 inches 35.99*20.73*5.16 inches 41.33*23.74*5.20 inches 40.31*22.78*5.04 inches 49.00*28.17*3.94 inches 47.85*27.02*5.08 inches 73.17*42.69*4.72 inches 393.26*393.26*100 mm 914.1*526.6*131 mm 1049.8*603*132 mm 1023.98*578.57*128 mm 1244.6*715.4*100 mm 1215.5*683.3*129 mm 1858.4*1084.4*120 mm Cabinet Color Black Black Black Black Black Black Black Cabinet Material Electro-Galvanized Steel Electro-Galvanized Steel Electro-Galvanized Steel Electro-Galvanized Steel Electro-Galvanized Steel Electro-Galvanized Steel Electro-Galvanized Steel Outline Dimension Regulations Power Monitor OSD & Multi Vision Monitor OSD & Multi Vision Monitor OSD & Multi Vision Monitor OSD & Multi Vision Electrical Ratings CE, FCC CE, FCC CE, FCC CE, FCC CE, FCC CE, FCC CE, FCC DC 24 V AC 100~240 V (50/60Hz) AC 100~240 V (50/60Hz) AC 100~240 V (50/60Hz) AC 100~240 V (50/60Hz) AC 100~240 V (50/60Hz) AC 100~240 V (50/60Hz) Operating Temperature 0~40 celsius 0~40 celsius 0~40 celsius 0~40 celsius 0~40 celsius 0~40 celsius 0~40 celsius Storage Temperature -20~65 celsius -20~65 celsius -20~65 celsius -20~65 celsius -20~65 celsius -20~65 celsius -20~65 celsius VESA Mounts Size 300*300 mm 600*300 mm 600*400 mm 600*400 mm 600*400 mm 600*400 mm 800*600 mm 21 Installation and User's Guide 6. MECHANICAL DRAWING Units : mm [inches] RNK22SNH RNK40NHF RNK46NHF RNK46SHF RNK55NHF RNK55SNF 22 Installation and User's Guide RNK82NNF 7. TROUBLESHOOTING * When the following troubles are occurred, follow the trouble shooting. Before contacting a service center. Troubleshooting The screen doesn’t show up Troubleshooting Tip 1. Make sure if the power supply is connected property 2. Turn on the power. 3. Select the input signal right for the connected port. The screen is too light or to dark Control the BRIGHTNESS The screen size is not fit for the PC signal Press the AUTO key among keys in the front. (It is used only in the PC signal) The screen color shows strange in the PC signal In the FUNCTION menu of OSD menu, perform the AUTOADJUST. 23