View The Manual

Transcript

OPERATOR’S MANUAL MANURE SPREADER MS1223 MS1227 HSMFG0903 Rev. 2 HPOMSP4 TABLE OF CONTENTS TABLE OF CONTENTS............................................................................INSIDE COVER WARRANTY & NOTES.............................................................................................................................1 DEALER PRE-DELIVERY & DELIVERY CHECKLIST...................................................3 S P E C I F I C AT I O N S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 BOLT TORQUE CHART................................................................................................6 BE ALERT SYMBOL.....................................................................................................7 SAFETY RULES........................................................................................................8-9 DANGER - WARNING DECALS..............................................................................10-11 OPERATION MS1223 & MS1227...........................................................................12-13 ADJUSTMENTS........................................................................................................13-15 LUBRICATION GUIDE MS1223 & MS1227.............................................................15-17 DECAL LOCATION MS1223 & MS1227................................................................18-19 TROUBLE SHOOTING.................................................................................................20 OPTIONAL EQUIPMENT....................................................................................................21 ORDERING PARTS - ABOUT IMPROVEMENTS...........................................................22 SERVICE & PARTS NOTES......................................................................................23 PARTS LISTS & DIAGRAMS MS1223 & MS1227.............................................24-45 SEMI-LIQUID PAN...................................................................................................24-25 OPTIONAL HYDRAULIC ENDGATE.......................................................................32-33 OPTIONAL TOP BEATER..............................................................................................37 OPTIONAL HYDRAULIC DRIVE.....................................................................................................40-45 SERVICE RECORDS.................................................................................................46 WARRANTY: Warranty coverage is provided by John Deere according to the terms of the Agricultural/Commercial & Consumer Equipment Warranty Statement. Carefully read the warranty statement on the back of your original purchase order for details on coverage and limitations of this warranty. NOTES -1- AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS FRONTIER DEALER PRE-DELIVERY CHECK LIST After the Manure Spreader has been completely set-up, check to be certain it is in correct running order before delivering to the customer. The following is a list of points to inspect. Check off each item as you have made the proper adjustments and found the item operating satisfactorily. ! ! ! ! ! ! ! PTO shields turn freely. All Shields and Guards are in place and fastened. All grease fittings have been lubricated and gearbox filled to proper level See lubrication guide in this manual. All mechanisms are operating trouble free. All roller chains are at proper tension. All bolts and fasteners are tight. All decals are in place and legible. (Dealer’s Name) Model Number Serial Number (Signature of Pre-Delivery Inspector) (Inspection Date) DEALER DELIVERY CHECK LIST This check list that follows is an important reminder of valuable information that should be passed on to the customer at the time this Manure Spreader is delivered. Check off each item as you explain it to the customer. This delivery check list, when properly filled out and signed assures the customer that the Pre-delivery service was satisfactorily performed. ! ! ! ! Explain to the customer that the pre-delivery inspection was made. Explain to the customer all saftey precautions they must exercise when operating this unit Explain recommended loads for different types of materials. Explain to customer that regular lubrication is required for proper operation and long life of machine. Show customer the lubrication section of Owner’s Manual. ! Give the customer Owner’s Manual and make sure he reads and understands all operating and service instructions. ! Record Serial Number on page 22 of this Manual. Date Delivered Dealer’s Name By Signature of Original Buyer -3- FRONTIER MODEL MS1223 & MS1227 MANURE SPREADER Your Frontier spreader has been manufactured of the finest quality materials and components. The performance you get from your machine is largely dependent upon how well you read and understand this manual and apply this knowledge. There is a right and a wrong way to do everything. Please do not assume that you know how to operate and maintain your spreader before reading this manual carefully. Keep this manual available for ready reference. S P E C I F I C AT I O N S MS1223 MS1227 Top Flare Width. . . . . . . . . . . . . . . . . . . . . . . . . . . . .68”. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68” Inside Width. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59-3/4”. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59-3/4” Inside Length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12’-1”. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14’-1” Inside Depth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28-3/8”. . . . . . . . . . . . . . . . . . . . . . . . . . . . .28-3/8” Overall Width w/295/75R22.5 Tires. . . . . . . . . . . . 92-1/2”. . . . . . . . . . . . . . . . . . . . . . . . . . . . .92-1/2” Overall Length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18’-6”. . . . . . . . . . . . . . . . . . . . . . . . . . . .20’-5-1/2” Overall Loading Height (Top of Flare). . . . . . . . . .51-1/2”. . . . . . . . . . . . . . . . . . . . . . . . . . . .51-1/2” Overall Height w/Hyd. Endgate. . . . . . . . . . . . . . . . 55”. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55” Diameter of Beater. . . . . . . . . . . . . . . . . . . . . . . . . .29”. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29” Weight w/295/75R22.5 Tires. . . . . . . . . . . . . . . . . 2890 Lbs. . . . . . . . . . . . . . . . . . . . . . . . .3230 Lbs. Capacity (Old Rating). . . . . . . . . . . . . . . . . . . . . . . .235 Bu. . . . . . . . . . . . . . . . . . . . . . . . . . . . .270 Bu. Capacity - Cu. Ft. Struck Level. . . . . . . . . . . . . . . . 143. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167 Rear Hydraulic Endgate. . . . . . . . . . . . . . . . . . . . . .Optional. . . . . . . . . . . . . . . . . . . . . . . . . . . Optional Semi Liquid Rear Pan. . . . . . . . . . . . . . . . . . . . . . .Standard. . . . . . . . . . . . . . . . . . . . . . . . . .Standard Upper Beater. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Optional. . . . . . . . . . . . . . . . . . . . . . . . . . . Optional Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Two Speed Gearbox. . . . . . . . . . . . . . . . . . . . . . . . Variable Speed Hydraulic Drive. . . . . . . . . . . . . . . Factory Installed Option Only. . . . . . . . . . . . . . . . . . Front Splash Panel. . . . . . . . . . . . . . . . . . . . . . . . . .Sandard. . . . . . . . . . . . . . . . . . . . . . . . . . Standard PTO Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 540 RPM. . . . . . . . . . . . . . . . . . . . . . . . . .540 RPM Note: Determine right and left side of spreader by viewing it from the rear. If instructions or parts lists call for hardened bolts see page 6 to identify. -5- -6- BE ALERT! YOUR SAFETY IS INVOLVED. THIS SYMBOL IS USED THROUGHOUT THIS BOOK WHENEVER YOUR PERSONAL SAFETY IS INVOLVED. TAKE TIME TO BE CAREFUL. REMEMBER: THE CAREFUL OPERATOR IS THE BEST OPERATOR. MOST ACCIDENTS ARE CAUSED BY HUMAN ERROR. CERTAIN PRECAUTIONS MUST BE OBSERVED TO PREVENT THE POSSIBILITY OF INJURY OR DAMAGE. TRACTORS This operator’s manual uses the term “Tractor” when identifying the power or the towing source. -7- RECOGNIZE SAFETY INFORMATION This is the safety-alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe operating practices. UNDERSTAND SIGNAL WORDS A signal word- DANGER, WARNING, or CAUTION - is used with the safety-alert symbol.DANGER identifies the most serious hazards. Safety signs with signal word DANGER or WARNING are typically near specific hazards. General precautions are listed on CAUTION safety signs. FOLLOW SAFETY INSTRUCTIONS Carefully read all safety messages in this manual, and all safety signs on your machine. Follow all recommended precautions and safe operating procedures. Keep signs in good condition. Immediately replace any missing or damaged signs. OBSERVE MAXIMUM TRANSPORT SPEED The maximum transport speed for this implement is 32 km/h (20 mph). Some tractors are capable of operating at speeds that exceed the maximum transport speed of this implement. Regardless of the maximum speed capability of the tractor being used to tow this implement, do not exceed the implement’s maximum transport speed. Exceeding " " " " the implements maximum transport speed can result in: Loss of control of the tractor/implement combination Reduced or no ability to stop during braking Implement tire failure Damage to the implement structure or its components Use additional caution and reduce speed when towing under adverse surface conditions, when turning, and when on inclines. Do not attempt transport if the fully loaded implement weighs more than 1.5 times the weight of the tractor. -8- TRACTORS This operators manual uses the term “Tractor” when identifying the power or the towing source. WARNING TO PREVENT SERIOUS INJURY OR DEATH BEFORE YOU ATTEMPT TO OPERATE THIS EQUIPMENT, READ AND STUDY THE FOLLOWING INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THIS EQUIPMENT, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESE SAFTEY PRECAUTIONS. KNOW HOW TO STOP UNLOADING MECHANISM BEFORE STARTING IT. If the machine becomes clogged, disengage the PTO. Stop the tractor engine, remove ignition key, and allow all mechanisms to stop before cleaning or working on the machine. Never allow riders in or on the machine. DO NOT get off the tractor while the spreader is in operation. DO NOT attempt to perform maintenance or repair with tractor running and PTO hooked up. DO NOT step up on machine at any time. NEVER manually feed material into the beaters. DO NOT allow minors to operate or be near the machine. DO NOT ALLOW PERSONNEL OTHER THAN THE QUALIFIED OPERATOR NEAR THE MACHINE. Before starting tractor, be sure PTO shields turn freely and PTO is securely locked to tractor. DO NOT clean, adjust, or lubricate the machine when any part is in operation. Keep hands, feet, and clothing away from beaters when they are revolving. Loose or floppy clothing should not be worn by the operator. Be sure the machine is clear of people, tools, and other objects before engaging PTO. DO NOT step over power take off shaft. Stay clear of PTO at all times. NEVER start manure spreader until all guards and safety shields are secured in place. NEVER operate spreader with a PTO speed Greater Than 540 RPM. Stay clear of Hydraulic Lines. They may be under extreme pressure or heat. Frontier always takes the operator and his safety into consideration and guards exposed moving parts for his protection. However, some areas cannot be guarded or shielded in order to assure proper operation. In addition, the operators manual and decals on the machine itself warn you of further danger and should be read and observed closely. Study The Above Safety Rules ATTENTION - BE ALERT - YOUR SAFETY IS INVOLVED -9- -10- -11- OPERATION 1. 2. 3. 4. 5. 6. Check for proper assembly and adjustment and make sure that all bolts are tightened. Securely retighten after a few hours of operation, as bolts can loosen up on new machinery. Check wheel bolts upon delivery and periodically thereafter. Wheel bolts should be tightened at 85-90 ft/lbs. of torque. Check the tires and inflate to the recommended pressure(295/75R22.5 tires to 55 pounds 16.5 x 16.1 tires to 36 pounds). Adjust the tractor hitch and attach the spreader to the tractor as described in the following sections. Attach the speed control/beater engage and disengage rope to a convenient point on the tractor. Lubricate the machine completely and check the oil level of gearbox. Before operation, run machine slowly to make sure that the spreader is operating and lubricated properly. TRACTOR HITCH The hitch of the spreader is designed for a standardized tractor hitch. Adjust the drawbar so that it is 13 to 17 inches above the ground. Extend or shorten it so that the horizontal distance from the end of the tractor power takeoff shaft to the center of the hitch pin hole is 14 inches, as shown in drawing. An improperly located hitch point may cause damage to the universal joints of the power takeoff. Secure the drawbar so that the hitch pin hole is directly below the power drive line. If this implement is attached to a tractor with a clevis hitch (hammer-strap) style drawbar, the hammer-strap must be removed to prevent damage to the IID guarding and the IID telescoping members.[See Figure 1] If this implement is attached to a tractor with an offset in the drawbar, be certain it is in the down position to prevent damage to the IID guarding and the IID telescoping members. [See Figure 2] ATTACHING TO THE TRACTOR 1. Fasten the spreader hitch to the drawbar with a hitch pin with a safety locking device. Use 1” diameter hitch pin to pull spreader. 2. Remove the weight from the jack (jack is not to be used when spreader is loaded). Remove jack from pipe mount and place on convenient storage mount located on top of left hitch channel. This allows protection of jack from tractor tires during turns. 3. Slide spring loaded locking collar on PTO yoke rearward, and slide it onto the tractor PTO shaft. Release spring loaded collar. Be sure the pins fall into the groove of the tractor PTO shaft and collar snaps forward into locking position. CAUTION: Do not use a steel hammer to aid in joining PTO parts. SERVICING Be certain to disconnect all sources of power before servicing. Keep pant cuffs and loose clothing away from all chains and gear drives as well as the other moving parts. Keep off the equipment when in use, and keep all safety shields in place. Do not attempt to clean, grease or lubricate while the machine is running. Never allow riders in or on the machine. When transporting on the highway, regularly clean the reflective tape at the rear of the spreader. There is a holder provided for your SMV sign. -12- LOADING In freezing weather, make certain that hydraulic tail gate (if equipped with one) is not frozen to the sides or on the floor of the spreader. Make sure the apron chain is not frozen to the spreader floor or any lumps of manure are frozen to the floor. Begin loading the spreader at the front end and work toward the rear until loading is completed. Loading this way permits the material to be spread uniformly. Loading front to rear is particularly important when the spreader is loaded by a mechanical loader because this type of load requires more power to spread than others loads. When hauling extremely heavy materials with a large portion of dirt, it may be necessary to reduce the load size to prevent excessive shear bolt breakage. Never dump material onto the beater. Do not use extra sideboards. Do not overload spreader. Overloading decreases spreading effectiveness. Do not load more than 15 inches above the beater. SPREADING NOTE: Two speed apron drive and beater engage/disengage mechanisms are contained in a single gearbox at the rear of spreader.This gearbox is controlled by one rope leading to the tractor. 1. When ready to unload, before engaging PTO, make sure that the gearbox is in the “low” position, with the shifter dog all the way to the “low” side of the indicator slot. 2. Raise the hydraulic endgate (if so equipped). 3. Engage the PTO slowly. 4. The apron speed may be increased from 4-1/2 fpm to 8-1/2 fpm (at 540 RPM) by pulling once on the control rope until the shifter stops and locks into the “high speed” position. The beater will continue to operate in this position. 5. When the spreader is almost empty, the bed can be cleaned out by again, pulling once on the control rope until the shifter dog locks into the “clean-out/beater disengaged” position. The beater will stop, and the apron will continue to run in the “high” speed position, thus saving unloading time. 6. When spreader is empty, SHUT OFF PTO. With the PTO off, pull the control rope once again and release it. The shifter will return to the “low” position, ready to begin unloading the next load. DO NOT SHIFT FROM CLEAN OUT TO LOW POSITION WITH THE PTO RUNNING. 7. Do not operate the spreader with a PTO speed greater than 540 RPM. Low Speed High Speed Clean Out ADJUSTMENTS FAILURE TO FOLLOW THE RECOMMENDED ADJUSTMENTS WILL VOID WARRANTY APRON 1. Adjust the apron by loosening the mounting bolts on the chain slides on the outside of the frame. Mounting bolts shown in the drawing. 2. Tighten the adjusting bolts until the apron chain clears clears the underside of the axle by 1 inch. NOTE: Tighten the adjusting bolts (on each front corner) equally on each side so that the apron slats run parallel with the ends of the bed. The apron will be damaged if the machine is operated with one end of the apron slats running ahead of the opposite end. Do not tighten the apron chains excessively. -13- MOUNTING BOLTS ADJUSTING BOLT DRIVE CHAIN To adjust front drive chain, turn nut on adjusting rod (located at the right hand front side of spreader) clodkwise. There should be 1/2” deflection at the center of the drive chain. Over tightening or too loose of a chain will result in excessive wear on the bearing, chain and sprockets. TIGHTENER BOLT ADJUSTING WHEEL HUBS To adjust wheel hubs, tighten the castellated nut on the spindle to the point where there is no end-play and a slight drag on the bearings. Replace the cotter key with a new one of the correct size. APRON WORM DRIVE CHAIN The main apron drive chain is kept tight with a nylon roller type adjustable tightener. Periodically check tension on chain. Chain is properly adjusted when there is 1/8” deflection in center of chain. Also check tightener for wear and replace when necessary. SHEAR BOLTS (Apron drive) The main apron is protected by two shear bolts located on the drive sprocket on the main conveyor drive shaft at the rear of the spreader. Two spare shear bolts are provided. Shearing of the bolts is normally due to the apron being frozen fast to the floor or the slats catching on manure that is frozen to the floor. In some cases, the bolt will shear due to the spreader being overloaded. Always determine the cause of the failure and eliminate the cause before installing new shear bolts. Always use Frontier shear bolts, part number HPD31, when replacing shear bolts. REPLACEMENT SHEAR BOLTS SHEAR BOLTS SHEAR BOLTS (Main Drive) The beater and the apron drive are protected by one shear bolt located on the front end of the side drive shaft (left side of spreader). Two spare shear bolts are provided. Shearing of the bolts is normally due to foreign objects in the manure or starting the spreader PTO too quickly with high tractor RPM’s. Always use Frontier shear bolts,part number HPD31, when replacing shear bolts. SHEAR BOLT SPARE SHEAR BOLTS Shields Removed for Clarity -14- APRON SPEED AND BEATER CONTROL One cable controls the beater and apron drive two speed gearbox. To compensate for wear or stretching of this cable adjust turnbuckle behind shield at left hand front of spreader. Refer to drawing to properly adjust manure spreader. Position speed control in HI Speed. Measurement (A) is 2-1/2 inches. This is factory set and should not be changed. Do not move bracket or collar on control rod. The distance between collar and face of gearbox should be as follows for the different speeds: (distance B) LO Speed: 0” (tight against gearbox) HI Speed: 7/16 -1/2” CLEAN OUT: 3/4-1 1/16” If collar on control rod does not pull tight to gearbox in LO Speed, after HI Speed has been properly adjusted, apply more tension to return spring behind shield at right hand front of spreader. To adjust spring, loosen bolt holding spring bracket on to adjustment rod. Slide spring bracket towards right side of spreader. Retighten bolt. SPRING BRACKET TURNBUCKLE Shields Removed for Clarity LUBRICATION GUIDE The operator should become familiar with all lubrication points and establish a systematic routine to insure complete and quick lubrication of the machine. GEARBOX- Before using your new machine, check the oil in the main apron drive and beater drive gearbox. Keep the gearbox filled to the oil plug on the rear of the gearbox as shown with Mobilube SHC 75W90 (or equivilant) gear lube. OIL LEVEL DRIVE CHAINS- Lubricate the drive chains with a light machine oil. Keep chains aligned with sprockets, this will lengthen the life of the sprockets and chain. Lubricate chains often. GREASE FITTINGS- There are eleven grease fittings on the Model MS1223 and thirteen on the Model MS1227 manure spreader. Thirteen and fifteen respectively if wquipped with haydraulic endgate. If these are lubricated properly and often enough, it will prolong the life of the spreader. (Grease every 20 hours, also before storage and after power washing.) Make certain that the grease fittings are free of paint and dirt. Force a high-quality grease into them until the grease comes out around the shaft on the sleeve-type bearings. On the sealed ball bearings, grease should be added slowly until a slight bead forms at the seals indicating the correct amount of lubricant. Wipe off excess grease to prevent the accumulation of chaff and grit around the bearings. (See page 16 for grease zerk location.) -15- LUBRICATION GUIDE (CONTINUED) GREASE ZERK LOCATION A. B. C. D. E. F. G. (3) PTO Shaft (2) Front jack shaft bearings. (2) Side shaft MS1223 (4) MS1227 (2) Rear drive shaft (LH is a remote fitting) (1) Rear drive shaft shear sprocket (1) Beater bearing (RH side) (2) Hydraulic endgate arms (If equipped with a Hydraulic Endgate) NOTE: Shields removed in some pictures for clarity. DO NOT OPERATE WITH SHIELDS REMOVED A B C D F E G -16- D LUBRICATION GUIDE (Continued) PTO ASSEMBLY- Care must be taken to keep the male and female driving elements well lubricated and free sliding. Failure to observe this precaution will result in excessive pressure being required to collapse or extend the assembly while subject to operating torque. This excessive force may damage or displace the jackshaft bearings. DO NOT lubricate the shield surfaces. The shield surfaces must be kept dry, as dirt accumulation on them will quickly cause these units to bind and not rotate. Care should also be taken to be certain that the rotating integral shields are not dented or damaged, as this also will result in excessive force being applied against the jackshaft. Damaged shields also cause obvious difficulties when installing the assembly. If at any time the shields do not turn freely, they should be checked to determine the cause, and repaired or cleaned. To avoid damage to the main drive bearings, avoid turning sharp corners while PTO is running. Start and Stop PTO slowly to avoid damage to the drive line. BEATER When replacing beater paddles, the sharp edges of the teeth must lead in the direction of beater travel. On the right half of the beater the teeth must point to the right side of the spreader. On the left half of the beater the teeth must point to the left side of the spreader. Always use Frontier special grade 5 bolts, washers, and nuts when replacing blades. Use Frontier part number HPR10 (1/2” GR.5 bolt), HPR11 (1/2” special nut). Torque to 60 foot lbs. When transporting on the highway, regularly clean the reflective tape at the rear of the spreader. Ther is a holder provided for your SMV sign. -17- DECAL LOCATION Your Frontier Manure Spreader was manufactured with operator safety in mind. Located on the manure spreader are various decals to aid in operation, and warn of danger or caution areas. Pay close attention to all decals on your Manure Spreader. DO NOT REMOVE ANY OF THESE DECALS. IF DECALS ARE LOST, DAMAGED,OR IF MANURE SPREADER IS REPAINTED, REPLACE DECALS. REMEMBER: DECALS ARE FOR YOUR PROTECTION AND INFORMATION. Listed below are the decals on your Manure Spreader. These decals may be ordered individually by part number or by ordering a complete set. ITEM A B C D E F G H I J K L M N O P Q R S T U V W X Y PART NO. HP1223 HP1227 HP82602 HP71188B HP2X9AMBER HP9194B HP1494J HP1494K HP1494B HP11599 HP12794 HP9194A HP1494L HP1494A HP82793 HPFRONTIER19 HP11211176 HP111593C HP111593A HP2X9RED HPHPFRON1 HP093020 HP71494A HPHS404 HP92606 5HP729031223 5HP729031227 DESCRIPTION (2) Frontier MS1223 Model Decal (2) Frontier MS1227 Model Decal Warning - Crushing Hazard Jack Storage Position Amber Reflector Danger - Never Allow Riders (2) Warning - Do Not Clean or Work (3) Warning - Do Not Remove Shields (2) Warning - Do Not Remove Shields Warning - Stay Clear of Leaks (2) Warning - Do Not Remove Shields (3) MS1227 (2) Danger - No Step - Stay Clear Danger - Rotating Driveline Serial Number (4) Warning - Do Not Operate Beater / Apron Control (3) Frontier Decal (2) Shear Bolts (2) Danger - Stay Clear of Endgate Arms (If Equipped) (2) Danger - Stay Clear of Beater (2) Red Reflectors Warning - Help Avoid Injury (2) Grease (2) Warning - Do Not Operate Patent Numbers Warning - Do Not Exceed Transport Speed Complete Set of Decals for MS1223 Complete Set of Decals for MS1227 P F I E U G X Q (Behind Shield) H J P A L M W B Y K C O -18- H D DECAL LOCATION (CONTINUED) J N N K B Shields Removed for Clarity R G F S P T G Q W (Behind Shield) S N T V Shields Removed for Clarity -19- R TROUBLE SHOOTING WARNING MAKE SURE THAT THE TRACTOR IS SHUT OFF AND THE SPREADER CAN NOT MOVE BEFORE SERVICING THE MANURE SPREADER. MAINTENANCE AND REPAIR SERVICE WORK TO BE PERFORMED BY A QUALIFIED SERVICE PERSON ONLY. TROUBLE... POSSIBLE CAUSE... POSSIBLE REMEDY... Beater Does Not Turn PTO Not Turning Engage Tractor PTO Beater Not Engaged Engage Beater (See page #13) Main Drive Shear Bolt Sheared Replace Main Drive Shear Bolt (See page #14) Beater Will Not Disengage Front Drive Chain Off, Replace or Repair Front Drive Chain Broken, or Missing (See page #14) Control Cable out of Adjustment Adjust Control Cable (See page#15) Splined Beater Insert Worn or Replace Splined Beater Insert and Splines Sheared Off Gearbox Output Shaft Control Cable Out of Adjustment Adjust Control Cable (See page #15) Control Linkage Binding Check Control Linkage, Make Sure It Is Free Moving Apron Does Not Turn PTO Not Turning Engage Tractor PTO Main Drive Shear Bolt Sheared Replace Main Drive Shear Bolt (See page #14) Apron Drive Shear Bolts Sheared Replace Apron Drive Shear Bolts (See page #14) Front Drive Chain Off, Broken, -20- OPTIONAL EQUIPMENT REAR PAN/SEMI-LIQUID HYDRAULIC ENDGATE The rear pan shown below is optional equipment on Models MS1223 & MS1227. Semi-liquid hydraulic endgate (pictured below right) is optional equipment on Models MS1223 & MS1227. Rear pan and hydraulic endgate may be used together on both models. REAR PAN HYDRAULIC ENDGATE TOP BEATER UPPER BEATER Optional upper beater available on both models will provide more uniform spreading in heaped and heavily matted material. Upper beater may be used with hydraulic endgate or rear pan. When transporting on the highway, regularly clean the reflective tape at the rear of the spreader. There is a holder provided for your SMV sign. -21- INSTRUCTIONS FOR ORDERING PARTS All service parts should be ordered through your authorized Frontier dealer. He will be able to give you faster service if you will provide him with the following. 1. 2. 3. 4. Model & Serial Number - Both can be located on the front center bearing post below the PTO shaft. All reference to left or right apply to the machine as viewed from the rear. Parts should not be ordered from illustration only. Please order by complete part number. If your dealer has to order parts - give shipping instructions VIA truck - large pieces (please specify local truck lines) VIA United Parcel Service (include full address) PLEASE RECORD NUMBERS FOR YOUR UNIT FOR QUICK REFERENCE ABOUT IMPROVEMENTS FRONTIER IS CONTINUALLY STRIVING TO IMPROVE IT’S PRODUCTS. We must therefore, reserve the right to make improvements or changes whenever it becomes practical to do so, without incurring any obligation to make changes or additions to the equipment previously sold. -22- SERVICE & PARTS NOTES -23- FIGURE 1 -24- FIGURE 1 FRONTIER MODELS MS1223 & MS1227 BEATER AND PAN ASSEMBLY SPREADER MODEL & PART NO. ITEM 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. MS1223 HP23N1 HP23N2 HP23N3 HP23N4 HP23N276 HP23N277 HP23N7 HP23N8 HPR10 HPR35 HPR11 HP23N263 HP5B9 HP23N10 HP23N11 HPF116 HPF115 HPF114A HPF16 HP23N12 HP23N13 HP23N14 HP23N264 HP23N265 HP23N17 HP23N257 HP23N19 HP23N20 HPR31 HP23N21 HPR27 HP23N22 HP23N23 HPA34 HPR70 HPF112 HP23N24 HP23N25 HP23N267 HP23N268 HP23N29 HP23N30 HP23N64 HP17G10 MS1227 “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ HP27N1 “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ NOTE: “(SAME PART NO. AS MODEL MS1223) -25- DESCRIPTION 5/16” X 5” GR.5 Bolt Splined Beater Insert Beater Blade Holder LH Beater Blade Holder RH Beater Blade - Hardened Beater Blade - Hardened Beater Blade Wiper LH Beater Blade Wiper RH 1/2” x 1-1/4” Bolt GR.5 1/2” Lock Washer 1/2” Lock Nut Beater 3/8” x 1-1/4” Woodruff Key Beater Shaft Support Beater Stub Shaft Bearing Flange (Heavy Duty) Bearing (Grease Type) Bearing Flange w/Zerk 45° Lock Collar Bearing Flange Guard RH Side Poly Hold Down LH Side Poly Hold Down LH Main Panel RH Main Panel Drive Shaft Bushing Drive Shaft Bracket LH Drive Shaft Bracket RH Pan Trip Rope Clip Pan Trip Lever Spring 1/2” x 1-1/2” Carriage Bolt Trip Lever Spacer 1/2” Flat Washer Cotter Pin Spacer Pan Rubber Flap Pan Strap Pan Support Brace LH Pan Support RH Pan Support Pan Shield Bracket LH Anti-Wrap Guard FIGURE 2 -26- FIGURE 2 FRONTIER MODELS MS1223 & MS1227 SPINDLE, HUB AND BOX PARTS SPREADER MODEL & PART NO. ITEM 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Not Shown 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. Not Shown Not Shown Not Shown Not Shown Not Shown MS1223 HP23N31 HP23N32 HPB8 HPB7 HPB7A HPB6 HPB32 HPB5A HPB5 HPB4 HPB31 HPB3 HPB2 HPB9 HP23N304 HP23N53 HP23N34 HPF33 HPF32 HP23N35 HP23N36 HP23N176 HP23N270 HP23N40 HP23N41 HP23N42 HP23N43 HP23N177 HP23N178 HP23N46 HPB106 HP23N271 HP23N272 HP23N273 HP12V36 HP23N54 HP23N179 HPMSO8C HP23N181 MS1227 “ “ HPB90 HPB91 HPB91A HP26G4 HPB93 HPB94A HPB94 “ “ “ “ HP27N2 HP27N46 “ “ “ “ “ “ “ “ “ “ “ “ HP27N24 HP27N25 “ “ HP27N36 HP27N37 HP27N38 “ “ “ “ HP27N26 NOTE: “(SAME PART NO. AS MODLE MS1223) -27- DESCRIPTION RH Side Stake LH Side Stake Seal Inner Bearing Inner Race Hub Hub Bolt Outer Race Outer Bearing Washer Cotter Pin Nut Hub Cap Spindle Spindle for 16.1 x 14 Wheel 1/2” x 4” Bolt GR. 5 Front Flare Rope Guide U-Bolt RH Gate Angle LH Gate Angle Front Flare Support Front Gate Plywood with Poly Strap for Rubber Front Gate Rubber Splash Guard Side LH Splash Guard Side RH RH Side Flare LH Side Flare Front Poly Floor Hold Down Bolts for Poly Floor Floor Plywood with Poly RH Side Plywood with Poly LH Side Plywood with Poly Wheel 16.1 x 14 Tire 16.5 x 16.1 Wheel 22.5 x 8.25 Tire 295/75R22.5 Complete Frame FIGURE 3 -28- FIGURE 3 FRONTIER MODELS MS1223 & MS1227 FRONT SHIELDS AND DRIVE ASSEMBLY SPREADER MODEL & PRAT NO. ITEM 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 20. 21. 22. 23. 24. * 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. * 41. 42. 43. 44. 45. 46. 47. 48. 49. 50. MS1223 HPF33 HP23N182 HP23N183 HP23N280 HP23N281 HPF84 HP23N282 HP10R14 HP23N283 HPS304 HP23N284 HP23N285 HP23N286 HPF44 HP23N287 HPR10 HP23N63 HPF129 HPF92 HPF56 HP23N305 HP23N66 HP23N67 HPHE42 HPF54 HP12N29 HPF73 HP5B10 HP5B9 HPF114 HPF115 HPF14 HPF16 HP23N68 HP23N244 HP23N70 HP23N245 HP23N72 HPF26 HP12N11 HP12N9 HP12N14 HP12N13 HP12N12 HPBFR247 HP23N278 HP23N297 HPS304 HPST81 HP37N74 HP23N306 MS1227 “ “ “ “ “ “ “ “ “ “ “ “ HP27N40 “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ HP27N14 “ “ “ “ “ “ “ “ “ “ “ NOTE: “(SAME PART NO. AS MODEL MS1223) * (PART NOT SHOWN) -29- DESCRIPTION Cable Guide Bracket Rope Shifter Lever Pivot Link Turnbuckle Shifter Dog Spring Stop Bracket Washer Shifter Dog Spring Front Panel Cable Cable Loop Spring Bracket Bolt Tightener Rod Washer Shield Bracket Clip Pin Front Shield RH Front Shield Tailgate Hose Bracket Hydraulic Bracket Shield Bearing Snap Ring 1/4” x 1” Key 3/8” x 1-1/4” Key Flange w/Zerk Bearing (Grease Type) Bearing Flange Lock Collar Front Adjustment Plate Spacer 25 Tooth Sprocket #60 Roller Chain 125 Pitches Front Shaft 5/16” x 2-1/4” Roll Pin Jack Jack Gear Repair Kit Jack Mount Jack Pin Handle Carriage Bolt 3/8” x 1” GR.5 Spacer Roller Washer Spacer (2) Front Shaft Guard Front Shield LH FIGURE 4 -30- FIGURE 4 FRONTIER MODELS MS1223 & MS1227 BACK SHIELDS AND DRIVE ASSEMBLY SPREADER MODEL & PART NO. ITEM MS1223 MS1227 1. HP23N247 HP27N39 2. HP23N248 “ 3. HP23N292 “ 4. HP23N250 “ 5. HP23N251 “ 6. HP23N252 “ 7. HP23N253 HP27N32 8. HP17G58 “ 9. HP23N288 “ 10. HP27N34 11. HP17G61 “ 12. HP23N266 “ 13. HPF44 “ 14. HP23N269 “ 15. HP17G65 “ 16. HP12N35 “ 17. HP12N33 “ 18. HP12N34 “ 19. HP12N36 “ 20. HP5B9 “ 21. HPD31 “ 22. HPD81 “ 23. HP23N189 “ 24. HPF16 “ 25. HPF114A “ 26. HPF115 “ 27. HPF14 “ 28. HP23N254 “ 29. HPF56 “ 30. HP23N191 “ 31. HP23N190 “ 32. HP23N255 HP27N33 33. HP16V9 “ 34. HPS47 “ 35. HP23N256 “ 36. HP23N257 “ 37. HP23N258 “ 38. HP17G67 “ 39. HP23N259 “ 40. HP10R32 “ 41. HP23N238 “ 42. HP17G69 “ 43. HP17G68 “ * HP17G170 “ * HP23N279 “ 44. HP17G71 “ 45. HPD31 “ 46. HPD81 “ 47. HP23N260 “ 48. HP23N261 “ 49. HPF92 “ 50. HP22G21 “ 51. HPX43 “ 52. HP23N289 “ 53. HP23N290 “ 54. HP23N291 “ 55. HP23N294 HP27N41 56. HP23N295 HP27N42 * 57. HP27N43 * 58. HP27N44 N OTE: “ (SAME PART NO. AS MODEL MS1223) - (PART IS NOT USED ON THIS MODEL) * (PART IS NOT SHOWN) -31- DESCRIPTION Side Shield Side Shield Bracket Coupler Shield Poly Shield Poly Pulley Pulley Mount Cable Vent Cap Pipe Nipple Back Side Shield Washer Pipe Spacer Cable Loop Bearing Bracket Coupler Holder Bearing Bearing Cover Complete Assembly 3/8” x 1-1/4” Woodruff Key Shear Bolt Lock Nut Snap Ring Lock Collar Flange Bearing (Grease Type) Bearing Flange Bearing Plate Clip Pin 30 Tooth Sprocket Shear Hub Side Shaft Grease Zerk Block Grease Line Fitting Grease Line LH Drive Shaft Mount Chain Oiler Worm Gear Sprocket Gearbox Brace Snap Ring Chain Tightener Roller Chain Tightener Bracket Shear Hub Sprocket - Standard (32T) Slow Down Sprocket (40T) Speed Up Sprocket (25T) Shear Hub Shear Bolt Lock Nut #60 Chain 56 Pitches Drive Shield Shield Angle Shield Cotter Pin Shifter Rod Lever Fulcrum Shifter Rod Lever Shifter Rod Angle 1st Side Shaft Guard 2nd Side Shaft Guard 3rd Side Shaft Guard 4th Side Shaft Guard FIGURE 5 -32- FIGURE 5 FRONTIER MODELS MS1223 & MS1227 OPTIONAL HYDRAULIC TAILGATE ASSEMBLY SPREADER MODEL & PART NO. ITEM MS1223 MS1227 1. HP23N298 “ 2. HP23N99 “ 3. HP23N100 “ 4. HP23N233 “ 5. HP23N274 “ 6. HP23N234 “ 7. HP23N104 “ 8. HP23N105 “ 9. HP23N67 “ 10. HPK132 “ 11. HP23N107 “ 12. HP23N108 “ 13. HP3G22 “ 14. HP23N109 “ 15. HP23N299 “ 16. HP23N111 “ 17. HP23N231 “ 18. HP23N113 “ 19. HP23N114 “ 20. HP23N300 “ 21. HP23N116 “ 22. HP23N117 “ 23. HP23N302 HP27N45 24. HP23N163 “ 25. HP23N232 “ 26. HP23N301 “ NOTE: “(SAME PART NO. AS MODEL MS1223) -33- DESCRIPTION Tailgate Frame RH Side Rubber LH Side Rubber Tailgate Bracket Brace Tailgate Plywood w/Poly 90° Street Elbow 3/8” Tailgate Corner Bottom Rubber Hose Bracket Spacer Cylinder Pin Cotter Pin Roll Pin 5/16”x1-3/4” Washer RH Tailgate Mount Hydraulic Cylinder Brace Hose (96”) Hose (138”) LH Tailgate Mount Tee Hose Holder Hose(MS1223-264” MS1227-288”) Tailgate Poly Hold Down Tailgate Bracket Brace Cylinder Pin FIGURE 6 FIGURE 6 FRONTIER MODELS MS1223 & MS1227 APRON CHAIN ASSEMBLY SPREADER MODEL & PART NO. ITEM 1. 2. 3. 4. 5. 6. 7. MS1223 MS1227 HP23N119 “ HP23N303 “ HP23N262 HP23N35 HPA32 “ HP23N121 “ HP23N122 “ HP23N123 HP27N20 8. HP23N124 “ 9. HPS55 “ 10. HPS55 “ 11. HP23N125 HP27N21 12. HPA30 “ 13. HP23N126 “ 14. HP23N127 “ 15. HP23N128 “ 16. HP23N129 “ 17. HP23N130 “ 18. HPA29 “ NOTE: “ (SAME PART NO. AS MODEL MS1223) - (PART IS NOT USED ON THIS MODEL) -34- DESCRIPTION Rear Poly Hold Down 3/8” x 1-3/4” Square Key Drive Shaft 3/8’ x 2-3/8” Sq.Key w/Round Ends Spacer Drive Sprocket 6T Apron Chain 17 Slats, 210 Links Apron Chain 20 Slats, 244 Links Slat w/Attachment Links T-Rod Standard Link T-Rod Standard Link Apron Chain Side Spacers Chain Slide Plate LH Chain Slide Spacer T-Rod Slide LH T-Rod Slide RH 1/2” x 4” Carriage Bolt GR.5 1/2” x 4-1/2” Bolt GR.5 Chain Slide Plate RH FIGURE 7 FIGURE 7 FRONTIER MODEL MS1223 & MS1227 OPTIONAL HYDRAULIC ENDGATE CYLINDER SPREADER MODEL & PART NO. ITEM MS1223 MS1227 1. HP23N142A “ 2. HP23N143A “ 3. HP23N144 “ 4. HP23N145A “ 5. HP23N146 “ 6. HP23N147 “ 7. HP23N148 “ 8. HP23N149 “ 9. HP23N150A “ 10. HP23N151 “ 11. HP23N111A “ NOTE: “ (SAME PART NO. AS MODEL MS1223) -35- DESCRIPTION Clevis Cap Rod Cap Piston Rod Cylinder Tube Tie Rod Piston Nut Plug Rod Clevis Seal Kit Hydraulic Cylinder FIGURE 8 FIGURE 8 FRONTIER MODEL MS1223 & MS1227 PTO ASSEMBLY SPREADER MODEL & PART NO. ITEM MS1223 MS1227 1. HP23N152 “ 2. HP23N153 “ 3. HPG1R35 “ 4. HP14NWKIT “ 5. HP23N155 “ 6. HP24N26 “ 7. HP4N20 “ 8. HP23N156 “ 9. HP23N157 “ 10. HP23N158 “ 11. HP23N159 “ 12. HP23N162 “ 13. HPS225 “ 14. HPS226 “ 15. HPS212 “ 16. HPS227 “ 17. HPS228 “ 18. HPS229 “ 19. HPS215 “ * HPS402 “ NOTE: “ (SAME PART NO. AS MODEL MS1223) * (PART IS NOT SHOWN) -36- DESCRIPTION PTO Assembly Complete w/Shields Machine Half PTO w/Shields End Yoke Machine Half Repair Kit Yoke and Tube Bearing Retainer Nylon Bearing Inner Guard Including Item #6 & #7 Tractor Half PTO w/Shield Outer Guard Including Item #6 & #7 Yoke and Shaft Lock Yoke Assembly Spring Lock Repair Kit Cover Stainless Ball Washer Spring Collar Assembly Retaining Ring PTO Safety Manual FIGURE 9 FIGURE 9 FRONTIER MODEL MS1223 & MS1227 OPTIONAL 2ND BEATER SPREADER MODEL & PART NO. ITEM MS1223 MS1227 1. HPF95 “ 2. HPF114 “ 3. HPF115 “ 4. HPF14 “ 5. HPF16 “ 6. HP23N164 “ 7. HP23N165 “ 8. HP23N166 “ 9. HPG23 “ 10. HPD18 “ 11. HP23N167 “ 12. HP12N42 “ 13. HP23N168 “ 14. HPF13 “ 15. HP5B9 “ 16. HPF56 “ 17. HP23N169 “ 18. HP23N170 “ 19. HP23N171 “ 20. HP23N172 “ 21. HP23N173 “ 22. HPF73 “ 23. HPF114 “ 24. HPA9 “ NOTE: “ (SAME PART NO. AS MODEL MS1223) -37- DESCRIPTION Bearing Flange Guard Bearing Flange w/Zerk Bearing Bearing Flange Lock Collar LH Stub Shaft RH Stub Shaft 2nd Beater 5/16” x 1-3/8” Square Key 16T Sprocket #60 Chain (81 Pitches) Idler Sprocket Spacer 20T sprocket 3/8” x 1-1/4” Key Clip Pin Cover Shield Shield RH Panel LH Panel Snap Ring Flange w/Straight Zerk Carriage Bolt 1/2” x 3-1/2” GR.5 FIGURE 10 -38- FIGURE 10 FRONTIER MODELS MS1223 &MS1227 GEARBOX SPREADER MODEL & PART NO. ITEM MS1223 MS1227 1. HP17G99 “ 2. HP17G100 3. HPS136 4. 5. DESCRIPTION ITEM MS1223 MS1227 DESCRIPTION Upper Gear Housing 34. HP17G118 “ 28T Gear w/clutch “ Cap 35. HP17G119 “ High Speed Clutch “ Seal 36. HP17G120 “ Worm Shaft HP17G58 “ Vent Cap 37. HP3G19 “ Retaining Ring HP23N288 “ Pipe Nipple 38. HPG90 “ Cap 6. HP17G171 “ Collar 39. HP17G121 “ Seal 7. HP17G61 “ Washer 40. HP17G122 “ Spacer 8. HP12V62 “ Retaining Ring 41. HP17G123 “ 3/16” x 1” Roll Pin 9. HP17G101 “ 22T Beveled Gear 42. HP17G124 “ Clutch Dog 10. HP17G102 “ Race 13621 43. HP17G125 “ High Speed Shifter Yoke 11. HP17G103 “ Bearing 13685 44. HP17G126 “ Dog Spring/Low Speed Clutch 12. HPG55 “ Retaining Ring 45. HP17G127 “ Stop Bolt 1/4”-20x3” Full Thread 13. HPG61 “ 3/8”x1-1/4” Hardened Woodruff Key 46. HP17G128 “ Spring/Beater Engage Beater Shifter Yoke 14. HP17G104 “ Beater Output Shaft 47. HP17G129 “ 15. HP17G105 “ Seal 48. HP17G130 “ 16. HP17G106 “ Adjustment Nut 49. HPS135 “ 1/4” x 1-1/4” Key 17. HPG65 “ Plug 50. HP17G131 “ Shifter Rod 18. HP17G107 “ Lower Gear Housing 51. HP17G132 “ 5/16” x 2-1/4” Key 19. HPG54 “ Race 14276 52. HP5B9 “ 3/8”x1-1/4” Woodruff Key 20. HPG18 “ Bearing 14124 53. HP17G133 “ Seal 21. HP17G108A “ Input Shaft 54. HP17G134 “ Bushing 1-1/2” IDx1-1/2”Length 22. HP17G109 “ Beater Clutch 55. HP17G135 “ Retaining Ring 23. HP17G110 “ 16T Beveled Gear w/Clutch 56. HP17G136 “ Worm Gear Output Shaft Spring/Beater Disengage 24. HP17G111 “ Bushing 1-1/2” IDx1” Length 57. HP17G137 “ Worm Gear 25. HPG68 “ Cap 58. HPA14 “ 3/8’ Lock Washer 26. HP3G18 “ Race 15245 59. HPX111 “ 3/8” x 1” Bolt GR.5 27. HPL3G24 “ Bearing 15113 60. HPK60 “ 3/8” Nut 28. HP17G112 “ Washer 61. HP17G138 “ 3/8” x 2” Stud 29. HP17G113 “ 32T Gear 62. HP17G139 “ 1-3/4” Cap 30. HP17G114 “ Gear Hub 63. HP17G140 “ 3/8” x 1-1/2” Stud 31. HP17G115 “ 20T Gear 64. HP17G141 “ 3/8”-16 x 1-1/4” Bolt 32. HP17G116 “ 1/4” x 5/8” Key 65. HP17G169A “ Snap Ring 33. HP17G117 “ 24T Gear * HP17G142 “ Complete Gearbox NOTE: “ (SAME PART NO. AS MODEL MS1223) * (PART IS NOT SHOWN) -39- FIGURE 11 -40- FIGURE 11 FRONTIER MODELS MS1223 &MS1227 HYDRAULIC DRIVE GEARBOX SPREADER MODEL & PART NO. ITEM MS1223 MS1227 1. HP17G99 “ 2. HP17G164 “ 3. HPS136 “ 4. HP12V62 “ 5. HP17G101 “ 6. HP17G102 “ 7. HP17G103 “ 8. HPG55 “ 9. HPG61 “ 10. HP17G104 “ 11. HP17G105 “ 12. HP17G106 “ 13. HPG65 “ 14. HP17G107 “ 15. HPG54 “ 16. HPG18 “ 17. HP17G108 “ 18. HP17G109 “ 19. HP17G110 “ 20. HP17G111 “ 21. HPG68 “ 22. HP3G18 “ 23. HPL3G24 “ 24. HP3G19 “ 25. HPG90 “ 26. HP17G132 “ 27. HP5B9 “ 28. HP17G133 “ 29. HP17G134 “ 30. HP17G135 “ 31. HP17G136 “ 32. HP17G137 “ 33. HPA14 “ 34. HPX111 “ 35. HPK60 “ 36. HP17G138 “ 37. HP17G139 “ 38. HP17G140 “ 39. HP17G141 “ 40. HPG24 “ 41. HP17G165 “ 42. HPA25 “ 43. HP23N89 “ 44. HP17G166 “ 45. HP17G167 “ 46. HP17G168 “ 47. HP5B10 “ NOTE: “ (SAME PART NO. AS MODEL MS1223) -41- DESCRIPTION Upper Gear Housing Seal Seal Retaining Ring 22T Beveled Gear Race (#13621) Bearing (#13685) Retaining Ring 3/8” x 1-1/4” Hardened Woodruff Key Beater Output Shaft Seal Adjustment Nut Plug Lower Gear Housing Race (#14276) Bearing (#14124) Input Shaft Beater Clutch 16T Beveled Gear w/Clutch Bushing 1-1/2” ID x 1” Length Cap Race (#15245) Bearing (#15113) Retaining Ring Cap 5/16” x 2-1/4” Key 3/8” x 1-1/4” Woodruff Key Seal Bushing 1-1/2” ID x 1-1/2” Length Retaining Ring Worm Gear Shaft Worm Gear 3/8” Lock Washer 3/8” x 1” Bolt GR. 5 3/8” Nut 3/8” x 2” Stud 1-3/4” Cap 3/8” x 1-1/2” Stud 3/8”-16 x 1-1/4” Bolt Vent Pipe Plug 5/8” Spacer 1” Spacer Clutch Spring Worm Shaft Bolt 3/4” Spacer 1/4” x 1” Key FIGURE 12 -42- FIGURE 12 FRONTIER MODELS MS1223 &MS1227 HYDRAULIC DRIVE 4-HOSE HOOK-UP SPREADER MODEL & PART NO. ITEM MS1223 MS1227 1. HPHE58 “ 2. HPDF15 “ 3. HPDF18 “ 4. HPDF7 “ 5. HPDF8 “ 6. HPHE14 “ 7. HPDF1 “ 8. HP23N132 “ 9. HPDF21 “ 10. HP23N133 “ 11. HPDF9 “ 12. HPK93 “ 13. HPDF12 “ 14. HPDF11 “ 15. HPDF10 “ 16. HPDF14 “ 17. HPDF22 “ 18. HP17G161 “ 19. HP17G162 “ 20. HP17G163 “ NOTE: “ (SAME PART NO. AS MS1223) -43- DESCRIPTION 90° Street Elbow Speed Control Check Valve Nipple Tee Hose Bracket Hydraulic Motor Hydraulic Motor Hose Reducer Control Panel Hose For Handle 3/8” Lock Nut Washer Handle Handle Bracket Strap Ring For Strap Coupler Mounting Bracket Complete Gearbox FIGURE 13 -44- FIGURE 13 FRONTIER MODELS MS1223 &MS1227 HYDRAULIC DRIVE 2-HOSE HOOK-UP SPREADER MODEL & PART NO. ITEM MS1223 MS1227 1. HP17G163 “ 2. HP17G162 “ 3. HP17G161 “ 4. HPDF1 “ 5. HP23N132 “ 6. HPDF21 “ 7. HP23N133 “ 8. HPDF9 “ 9. HPK93 “ 10. HPDF12 “ 11. HPDF11 “ 12. HPDF10 “ 13. HPDF22 “ 14. HPDF14 “ 15. HPDF6 “ 16. HPDF7 “ 17. HPDF8 “ 18. HPHE14 “ 19. HPDF18 “ 20. HPDF19 “ 21. HPDF17 “ 22. HPDF15 “ 23. HPDF16 “ 24. HPHE58 “ NOTE: “ (SAME PART NO. AS MS1223) -45- DESCRIPTION Complete Gearbox Mounting Bracket Coupler Hydraulic Motor Hydraulic Motor Hose Reducer Control Panel Hose For Handle 3/8” Lock Nut Washer Handle Handle Bracket Ring For Strap Strap Sequence Valve Nipple Tee Hose Bracket Check Valve Tee Nipple Speed Control Drain Hose 90° Street Elbow SERVICE / MAINTENANCE RECORD DATE DESCRIPTION NOTES -46-