Transcript
IM948-A VISTA™ AUTO-DARKENING FILTER CARTRIDGE (ADF) HELMETS
October, 2008
This manual covers equipment which is no longer in production by The Lincoln Electric Co. Specifications and availability of optional features may have changed.
TABLE OF CONTENTS SAFETY WARNINGS – READ BEFORE USING
1
PATENT INFORMATION
2
SPECIFICATIONS
2
OPERATING INSTRUCTIONS
3-4
SHADE GUIDE
5-6
LENS REPLACEMENT
7-8
HELMET CARE AND MAINTENANCE
OPERATOR’S MANUAL
Copyright © Lincoln Global Inc.
• World's Leader in Welding and Cutting Products • • Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
Page
9
TROUBLE SHOOTING
10
WARRANTY INFORMATION
11
REPLACEMENT PARTS
12
IM948-A VISTA™ AUTO-DARKENING FILTER CARTRIDGE (ADF) HELMETS
October, 2008
TABLE OF CONTENTS SAFETY WARNINGS – READ BEFORE USING
1
PATENT INFORMATION
2
SPECIFICATIONS
2
OPERATING INSTRUCTIONS
3-4
SHADE GUIDE
5-6
LENS REPLACEMENT
7-8
HELMET CARE AND MAINTENANCE
OPERATOR’S MANUAL
Copyright © Lincoln Global Inc.
• World's Leader in Welding and Cutting Products • • Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
Page
9
TROUBLE SHOOTING
10
WARRANTY INFORMATION
11
REPLACEMENT PARTS
12
SAFETY WARNINGS – READ BEFORE USING
PATENT INFORMATION
WARNING ARC Rays can injure eyes and burn skin • Before welding, always inspect helmet and filter lens to be sure they are in good condition and not damaged. • Check to see that the clear lens is clean and securely attached to the helmet. • Always wear safety glasses or goggles under the welding helmet and protective clothing to protect your skin from radiation, burns and spatter. FUMES AND GASES can be dangerous to your health. • Keep your head out of fumes. • Use enough ventilation or exhaust at the arc or both to keep fumes and gases from your breathing zone and general area. • See www.lincolnelectric.com/community/safety/ Note: For Auto-darkening Filters only: Auto darkening Filters in Lincoln helmets are designed to protect the user against harmful ultra-violet and infrared rays both in the dark and light states. No matter what shade the filter is set to, the UV/IR protection is always present. • The user's eyes can be severely burned if welding with a damaged lens, (cracked, pitted, etc..) Auto-darkening filters (ADF) protect the user against harmful ultra-violet and infrared rays, both in the dark and the light states. No matter what shade the filter is set to, the UV/IR protection is always there. As long as the lens is not damaged and is operating properly, you are protected from the optical radiation passing through the filter.
Patent Pending
SPECIFICATIONS Product Name Description LCD Size WxH
Vista 1000
Vista 2000
ADF Shade 9-13 ADF Shade 9-13 ADF Shade 9-13 mm inch
95 x 35 3-3/4 x 1-3/8
95 x 48 3-3/4 x 1-7/8
ADF Range
9,10,12,13
Light State
3
Sensitivity
Grind/Normal/TIG
4
Sensors Light to Dark
0.1ms
Dark to Light
0.1s (fast) 2.0 s (slow)
TIG Amps
5 ANSI Z87.1, CSA Z94.3
WARNING • Optical radiation can enter in from behind the helmet and ADF lens from other welderʼs arcs in the immediate area. • ANSI defines all welding helmets as a secondary eye protection from optical radiation and impact. For complete safety, primary protection, such as safety glasses, spectacles or goggles, should be used in conjunction with welding helmets. Protective clothing and accessories such as leather bibs attached to the welding helmet will protect the user from spatter and optical radiation indirectly entering from areas behind the helmet. • ACGIH (American Conference of Governmental Industrial Hygienists) has established a TLV-TWA of 5 mg/m3 for welding fumes. Welding fumes can not be simply classified. The composition and quantity of fumes are both dependent on the alloy being welded and the arc welding process and consumable type used
1
98 x 81 3-7/8 x 3-1/8
Fast/Slow
Delay Modes
Compliance
Vista 3000
2
SAFETY WARNINGS – READ BEFORE USING
PATENT INFORMATION
WARNING ARC Rays can injure eyes and burn skin • Before welding, always inspect helmet and filter lens to be sure they are in good condition and not damaged. • Check to see that the clear lens is clean and securely attached to the helmet. • Always wear safety glasses or goggles under the welding helmet and protective clothing to protect your skin from radiation, burns and spatter. FUMES AND GASES can be dangerous to your health. • Keep your head out of fumes. • Use enough ventilation or exhaust at the arc or both to keep fumes and gases from your breathing zone and general area. • See www.lincolnelectric.com/community/safety/ Note: For Auto-darkening Filters only: Auto darkening Filters in Lincoln helmets are designed to protect the user against harmful ultra-violet and infrared rays both in the dark and light states. No matter what shade the filter is set to, the UV/IR protection is always present. • The user's eyes can be severely burned if welding with a damaged lens, (cracked, pitted, etc..) Auto-darkening filters (ADF) protect the user against harmful ultra-violet and infrared rays, both in the dark and the light states. No matter what shade the filter is set to, the UV/IR protection is always there. As long as the lens is not damaged and is operating properly, you are protected from the optical radiation passing through the filter.
Patent Pending
SPECIFICATIONS Product Name Description LCD Size WxH
Vista 1000
Vista 2000
ADF Shade 9-13 ADF Shade 9-13 ADF Shade 9-13 mm inch
95 x 35 3-3/4 x 1-3/8
95 x 48 3-3/4 x 1-7/8
ADF Range
9,10,12,13
Light State
3
Sensitivity
Grind/Normal/TIG
4
Sensors Light to Dark
0.1ms
Dark to Light
0.1s (fast) 2.0 s (slow)
TIG Amps
5 ANSI Z87.1, CSA Z94.3
WARNING • Optical radiation can enter in from behind the helmet and ADF lens from other welderʼs arcs in the immediate area. • ANSI defines all welding helmets as a secondary eye protection from optical radiation and impact. For complete safety, primary protection, such as safety glasses, spectacles or goggles, should be used in conjunction with welding helmets. Protective clothing and accessories such as leather bibs attached to the welding helmet will protect the user from spatter and optical radiation indirectly entering from areas behind the helmet. • ACGIH (American Conference of Governmental Industrial Hygienists) has established a TLV-TWA of 5 mg/m3 for welding fumes. Welding fumes can not be simply classified. The composition and quantity of fumes are both dependent on the alloy being welded and the arc welding process and consumable type used
1
98 x 81 3-7/8 x 3-1/8
Fast/Slow
Delay Modes
Compliance
Vista 3000
2
OPERATING INSTRUCTIONS
AUTO-DARKENING CARTRIDGE CONTROLS: VISTA™ - 4 x 5 ADF include Variable Shade, Sensitivity and Delay.
HEADGEAR ADJUSTMENT
To make adjustments to your ADF controls, push appropriate button through clear protective lens until desired setting is achieved. There is no need to disassemble helmet to access control buttons on your ADF cartridge. Simply press directly on the inside cover lens to change button settings.
HEAD SIZE ADJUSTMENT: HEADGEAR TIGHTNESS is adjusted by pushing in the Ratchet Knob and turning to adjust for the desired head size. This knob is located at the back of the helmet. HEADGEAR CROWN ADJUSTMENT is made by adjusting for comfort and snapping the pin into the hole to lock securely in place. TILT: Tilt adjustment is located on left side of helmet. Loosen the left headgear tension knob and push the top end of the adjustment lever inward until the leverʼs Stop Tab clears the notches. Then rotate the lever up or down to the desired tilt position. The Stop will automatically engage again when released locking the helmet into position. FORE / AFT ADJUSTMENT: Adjusts the distance between userʼs face and lens. To adjust, loosen both outside tension knobs and slide forward or back to desired position and retighten. NOTE: Make sure both sides are equally positioned for proper operation. BATTERIES: No batteries are required! This product is solar powered and contains solar panels. CAUTION: Insure the solar panels are facing forward toward the outside of the helmet to capture light from the welding arc and surrounding environment. 3
Test your ADF filter prior to welding by directing the front of the filter toward a bright source of light, then using your fingers rapidly cover and uncover the sensors. The filter should darken momentarily as the sensor is exposed. A torch striker can also be used. SENSITIVITY MODE Select the sensitivity of the filter by pushing the Sensitivity button. You can choose Grind, Normal or TIG. Grind mode allows you to use the filter with a constant shade when grinding, so that raising the helmet is unnecessary. Set Grind mode by pressing and holding down the button until the filter LCD flickers. To remove from Grind mode press the button again (note: the filter will not flicker). Normal mode (no LEDs are on) is recommended for general welding and production welding (i.e. where welders are welding in close proximity to each other). Set Normal mode by pressing button until no LEDs are on (Grind and TIG LED are not on). TIG mode is recommended for situations where the filter may be temporarily blocked or the welding amperage is low. Set TIG mode by pressing button until TIG LED is on. 4
OPERATING INSTRUCTIONS
AUTO-DARKENING CARTRIDGE CONTROLS: VISTA™ - 4 x 5 ADF include Variable Shade, Sensitivity and Delay.
HEADGEAR ADJUSTMENT
To make adjustments to your ADF controls, push appropriate button through clear protective lens until desired setting is achieved. There is no need to disassemble helmet to access control buttons on your ADF cartridge. Simply press directly on the inside cover lens to change button settings.
HEAD SIZE ADJUSTMENT: HEADGEAR TIGHTNESS is adjusted by pushing in the Ratchet Knob and turning to adjust for the desired head size. This knob is located at the back of the helmet. HEADGEAR CROWN ADJUSTMENT is made by adjusting for comfort and snapping the pin into the hole to lock securely in place. TILT: Tilt adjustment is located on left side of helmet. Loosen the left headgear tension knob and push the top end of the adjustment lever inward until the leverʼs Stop Tab clears the notches. Then rotate the lever up or down to the desired tilt position. The Stop will automatically engage again when released locking the helmet into position. FORE / AFT ADJUSTMENT: Adjusts the distance between userʼs face and lens. To adjust, loosen both outside tension knobs and slide forward or back to desired position and retighten. NOTE: Make sure both sides are equally positioned for proper operation. BATTERIES: No batteries are required! This product is solar powered and contains solar panels. CAUTION: Insure the solar panels are facing forward toward the outside of the helmet to capture light from the welding arc and surrounding environment. 3
Test your ADF filter prior to welding by directing the front of the filter toward a bright source of light, then using your fingers rapidly cover and uncover the sensors. The filter should darken momentarily as the sensor is exposed. A torch striker can also be used. SENSITIVITY MODE Select the sensitivity of the filter by pushing the Sensitivity button. You can choose Grind, Normal or TIG. Grind mode allows you to use the filter with a constant shade when grinding, so that raising the helmet is unnecessary. Set Grind mode by pressing and holding down the button until the filter LCD flickers. To remove from Grind mode press the button again (note: the filter will not flicker). Normal mode (no LEDs are on) is recommended for general welding and production welding (i.e. where welders are welding in close proximity to each other). Set Normal mode by pressing button until no LEDs are on (Grind and TIG LED are not on). TIG mode is recommended for situations where the filter may be temporarily blocked or the welding amperage is low. Set TIG mode by pressing button until TIG LED is on. 4
SHADE SETTING: Shade selection is accomplished by pushing the Shade button on the back of the filter. Follow shade selection chart. 13
12
10
9
GRIND
TIG
SHADE
SENSITIVITY
CHECK SETTINGS
GRIND (PRESS-HOLD)
DELAY
GUIDE FOR SHADE NUMBERS ELECTRODE SIZE 1/32 in. (mm)
ARC CURRENT (A)
MINIMUM PROTECTIVE SHADE
SUGGESTED(1) SHADE NO. (COMFORT)
Shielded metal arc welding
Less than 3 (2.5) 3-5 (2.5–4) 5-8 (4–6.4) More than 8 (6.4)
Less than 60 60-160 160-250 250-550
7 8 10 11
– 10 12 14
Gas metal arc welding and flux cored arc welding
Less than 60 60-160 160-250 250-500
7 10 10 10
– 11 12 14
Gas tungsten arc welding
Less than 50 50-150 150-500
8 8 10
10 12 14
Less than 500 500-1000
10 11
12 14
Less than 20 20-100 100-400 400-800
6 8 10 11
6 to 8 10 12 14
Less than 300 300-400 400-800
8 9 10
9 12 14
Torch brazing
–
–
3 or 4
Torch soldering
–
–
2
Carbon arc welding
–
–
14
(Light) (Heavy)
Plasma arc welding
Plasma arc cutting
(2)
(Light) (2) (Medium) (Heavy)(2)
in.
• DO NOT WELD WITH A DAMAGED OR DEFECTIVE LENS, i.e. cracked, pitted, etc.
FAST SLOW
OPERATION
Air carbon Arc cutting
WARNING
DELAY MODE: Set the Delay to Fast or Slow by pushing the Delay button. The Slow setting is recommended for high amperage applications where the weld puddle is still very bright after the welding arc has ceased and for situations where the filter may be temporarily blocked from seeing the welding arc. ALWAYS TEST TO BE SURE THE ADF CARTRIDGE IS CHARGED BEFORE WELDING. The helmet can be placed in sunlight to charge. Do not store the helmet in a dark cabinet or other storage area for extended periods. While welding the Arc also charges the ADF cartridge. Recommended welding processes and cartridge settings can vary for each welding application. For some low amperage welding applications, cartridge performance will improve if the Delay Mode is set to SLOW. AUTO DARKING FILTER / HELMET STORAGE: • Store in a clean dry location.
PLATE THICKNESS mm
Gas welding Light Medium Heavy
Under 1/8 1/8 to 1/2 Over 1/2
Under 3.2 3.2 to 12.7 Over 12.7
4 or 5 5 or 6 6 or 8
Oxygen cutting Light Medium Heavy
Under 1 1 to 6 Over 6
Under 25 25 to 150 Over 150
3 or 4 4 or 5 5 or 6
(1) As a rule of thumb, start with a shade that is too dark, then go to a lighter shade which gives sufficient view of the weld zone without going
below the minimum. In oxyfuel gas welding or cutting where the torch produces a high yellow light, it is desirable to use a filter lens that absorbs the yellow or sodium line the visible light of the (spectrum) operation .
(2) These values apply where the actual arc is clearly seen. Experience has shown that lighter filters may be used when the arc is hidden by the workpiece. Data from ANSI Z49.1-2005
If your helmet does not include any one of the shades referenced above, it is recommended you use the next darker shade. 5
6
SHADE SETTING: Shade selection is accomplished by pushing the Shade button on the back of the filter. Follow shade selection chart. 13
12
10
9
GRIND
TIG
SHADE
SENSITIVITY
CHECK SETTINGS
GRIND (PRESS-HOLD)
DELAY
GUIDE FOR SHADE NUMBERS ELECTRODE SIZE 1/32 in. (mm)
ARC CURRENT (A)
MINIMUM PROTECTIVE SHADE
SUGGESTED(1) SHADE NO. (COMFORT)
Shielded metal arc welding
Less than 3 (2.5) 3-5 (2.5–4) 5-8 (4–6.4) More than 8 (6.4)
Less than 60 60-160 160-250 250-550
7 8 10 11
– 10 12 14
Gas metal arc welding and flux cored arc welding
Less than 60 60-160 160-250 250-500
7 10 10 10
– 11 12 14
Gas tungsten arc welding
Less than 50 50-150 150-500
8 8 10
10 12 14
Less than 500 500-1000
10 11
12 14
Less than 20 20-100 100-400 400-800
6 8 10 11
6 to 8 10 12 14
Less than 300 300-400 400-800
8 9 10
9 12 14
Torch brazing
–
–
3 or 4
Torch soldering
–
–
2
Carbon arc welding
–
–
14
(Light) (Heavy)
Plasma arc welding
Plasma arc cutting
(2)
(Light) (2) (Medium) (Heavy)(2)
in.
• DO NOT WELD WITH A DAMAGED OR DEFECTIVE LENS, i.e. cracked, pitted, etc.
FAST SLOW
OPERATION
Air carbon Arc cutting
WARNING
DELAY MODE: Set the Delay to Fast or Slow by pushing the Delay button. The Slow setting is recommended for high amperage applications where the weld puddle is still very bright after the welding arc has ceased and for situations where the filter may be temporarily blocked from seeing the welding arc. ALWAYS TEST TO BE SURE THE ADF CARTRIDGE IS CHARGED BEFORE WELDING. The helmet can be placed in sunlight to charge. Do not store the helmet in a dark cabinet or other storage area for extended periods. While welding the Arc also charges the ADF cartridge. Recommended welding processes and cartridge settings can vary for each welding application. For some low amperage welding applications, cartridge performance will improve if the Delay Mode is set to SLOW. AUTO DARKING FILTER / HELMET STORAGE: • Store in a clean dry location.
PLATE THICKNESS mm
Gas welding Light Medium Heavy
Under 1/8 1/8 to 1/2 Over 1/2
Under 3.2 3.2 to 12.7 Over 12.7
4 or 5 5 or 6 6 or 8
Oxygen cutting Light Medium Heavy
Under 1 1 to 6 Over 6
Under 25 25 to 150 Over 150
3 or 4 4 or 5 5 or 6
(1) As a rule of thumb, start with a shade that is too dark, then go to a lighter shade which gives sufficient view of the weld zone without going
below the minimum. In oxyfuel gas welding or cutting where the torch produces a high yellow light, it is desirable to use a filter lens that absorbs the yellow or sodium line the visible light of the (spectrum) operation .
(2) These values apply where the actual arc is clearly seen. Experience has shown that lighter filters may be used when the arc is hidden by the workpiece. Data from ANSI Z49.1-2005
If your helmet does not include any one of the shades referenced above, it is recommended you use the next darker shade. 5
6
LENS REPLACEMENT OUTSIDE PROTECTIVE COVER LENS REPLACEMENT: Press down on the Tab inside the top of the helmet while also pressing in on the Finger Tabs on both sides of the bezel piece on the front of the helmet. Pull the bezel outward to remove. Remove the polycarbonate protective lens. Place the new Polycarbonate lens in the recessed lens area. Be sure cover lens is properly seated. Then, simply insert the lower tabs of the bezel back into the helmet shell and rotate up, snapping the bezel into place. Ensure all three tabs have been correctly snapped in. Never use the AutoDarkening cartridge without the inside and outside cover lens properly installed. Tab
AUTO-DARKENING CARTRIDGE ACCESS AND REPLACEMENT: Remove Bezel as described in previous section on Lens Replacement. After removing the outside lens, simply remove the Adaptor by applying thumb pressure to top center tab to release top portion of Adaptor. Pull forward and release feet of Adaptor from Shell. Then remove the ADF filter. When replacing, be sure the light sensors are facing toward the front of the helmet when replacing the cartridge. Replace the inside cover lens, Cartridge, Adaptor, outside spatter lens and Bezel in reverse order. The outer polycarbonate lens is required to protect the ADF from weld spatter and impacts.
Lens Removal Finger Tab
Finger Tab
7
INSTALLING AN AFTERMARKET MAGNIFYING LENS Simply slide the magnifying lens into the short rails located over the protective cover lens.
8
LENS REPLACEMENT OUTSIDE PROTECTIVE COVER LENS REPLACEMENT: Press down on the Tab inside the top of the helmet while also pressing in on the Finger Tabs on both sides of the bezel piece on the front of the helmet. Pull the bezel outward to remove. Remove the polycarbonate protective lens. Place the new Polycarbonate lens in the recessed lens area. Be sure cover lens is properly seated. Then, simply insert the lower tabs of the bezel back into the helmet shell and rotate up, snapping the bezel into place. Ensure all three tabs have been correctly snapped in. Never use the AutoDarkening cartridge without the inside and outside cover lens properly installed. Tab
AUTO-DARKENING CARTRIDGE ACCESS AND REPLACEMENT: Remove Bezel as described in previous section on Lens Replacement. After removing the outside lens, simply remove the Adaptor by applying thumb pressure to top center tab to release top portion of Adaptor. Pull forward and release feet of Adaptor from Shell. Then remove the ADF filter. When replacing, be sure the light sensors are facing toward the front of the helmet when replacing the cartridge. Replace the inside cover lens, Cartridge, Adaptor, outside spatter lens and Bezel in reverse order. The outer polycarbonate lens is required to protect the ADF from weld spatter and impacts.
Lens Removal Finger Tab
Finger Tab
7
INSTALLING AN AFTERMARKET MAGNIFYING LENS Simply slide the magnifying lens into the short rails located over the protective cover lens.
8
HELMET CARE AND MAINTENANCE Virtually maintenance free: • Periodic cleaning with soapy water solution or standard glass cleaner is suggested for any ADF to function properly. Use soft cloth or eye glass wipes. • This ADF is water resistant. Do “NOT” submerge in water or other solution.
TROUBLE SHOOTING GUIDE Test your ADF filter prior to welding by directing the front of the filter toward a bright source of light, then using your fingers rapidly cover and uncover the sensors. The filter should darken momentarily as the sensor is exposed. A torch striker can also be used. Difficult to see through the filter: • Clean or replace protective cover lenses. • Clean the Auto-Darkening cartridge by using a cloth with soapy water solution or standard window cleaner.
• Change or clean cover lens when it becomes dirty or cloudy. Storage: • Store in a clean dry location.
The ADF will not darken after striking an arc: • Avoid blocking the Solar Panels. Must be facing forward (outside of) in the helmet. • Test the ADF by exposing to a bright light source and run your fingers quickly over the arc sensors. The filter should darken momentarily then switch back to the light state. Slow to darken: • If the filter has not been used for a day or more, the circuitry will enter a sleep mode. It will wake up when tested or when you begin welding. Note that the first time, it may darken to a lighter shade even though set for a darker shade. After the first time, it will darken to the correct shade setting every time. It is recommended to test your ADF prior to welding. • Colder temperatures can slow the switching speed of any ADF. Once the helmet warms up from the welding process, the switching will increase to rated speeds. ADF (Auto-Darkening Filter Cartridge) flickers or returns to light state while welding: • Clean or replace protective cover lenses if dirty or cloudy. • Check that the solar panels or sensors are not damaged or dirty. Clean with a soft cloth and soapy water solution or standard glass cleaner. Do not use abrasive or dirty cloths. • Make sure you are not blocking the sensors or solar panels with your arm or other obstacle (including the welding torch gun or nozzle) while welding. Adjust your position so that the sensors can “see” the weld arc.
9
10
HELMET CARE AND MAINTENANCE Virtually maintenance free: • Periodic cleaning with soapy water solution or standard glass cleaner is suggested for any ADF to function properly. Use soft cloth or eye glass wipes. • This ADF is water resistant. Do “NOT” submerge in water or other solution.
TROUBLE SHOOTING GUIDE Test your ADF filter prior to welding by directing the front of the filter toward a bright source of light, then using your fingers rapidly cover and uncover the sensors. The filter should darken momentarily as the sensor is exposed. A torch striker can also be used. Difficult to see through the filter: • Clean or replace protective cover lenses. • Clean the Auto-Darkening cartridge by using a cloth with soapy water solution or standard window cleaner.
• Change or clean cover lens when it becomes dirty or cloudy. Storage: • Store in a clean dry location.
The ADF will not darken after striking an arc: • Avoid blocking the Solar Panels. Must be facing forward (outside of) in the helmet. • Test the ADF by exposing to a bright light source and run your fingers quickly over the arc sensors. The filter should darken momentarily then switch back to the light state. Slow to darken: • If the filter has not been used for a day or more, the circuitry will enter a sleep mode. It will wake up when tested or when you begin welding. Note that the first time, it may darken to a lighter shade even though set for a darker shade. After the first time, it will darken to the correct shade setting every time. It is recommended to test your ADF prior to welding. • Colder temperatures can slow the switching speed of any ADF. Once the helmet warms up from the welding process, the switching will increase to rated speeds. ADF (Auto-Darkening Filter Cartridge) flickers or returns to light state while welding: • Clean or replace protective cover lenses if dirty or cloudy. • Check that the solar panels or sensors are not damaged or dirty. Clean with a soft cloth and soapy water solution or standard glass cleaner. Do not use abrasive or dirty cloths. • Make sure you are not blocking the sensors or solar panels with your arm or other obstacle (including the welding torch gun or nozzle) while welding. Adjust your position so that the sensors can “see” the weld arc.
9
10
ADF stays dark after you stop welding: • The temperature limitations of the ADF have been exceeded. Let the ADF cool down and try not to over heat it again by viewing the arc from the side or at a greater distance. • It may remain dark if you are facing a bright light or the sun. Look away or pass your hand between the sensor and light source. ADF is cracked: • Cease (STOP) using this product if this problem exists. UV/IR protection may be compromised resulting in burns to the eyes or skin. Weld Spatter is Damaging the ADF: • Missing, damaged, broken, cracked or distorted Protective Cover Lens. Replace inside and outside Clear Cover Lenses as needed.
WARNING • Do not use this product if severe spatter damage has occurred to the Auto-Darkening Filter Cartridge or protective clear cover lens. Severe eye damage and burns can result.
REPLACEMENT PARTS ITEM
PART No.
DESCRIPTION
QTY.
1
Note 1
5x4 SHELL, BLACK
1
2 3 4
Note 1 Note 1 KP2796-1 K2690-1
1 1 2 1
5
K2690-2
ADAPTOR BEZEL, BLACK CLEAR POLYCARBONATE LENS ADF 9-13 SHADE CARTRIDGE – SMALL VISTA 1000 ADF 9-13 SHADE CARTRIDGE - MEDIUM VISTA 2000 ADF 9-13 SHADE CARTRIDGE - LARGE VISTA 3000 RATCHET HEADGEAR ADJUSTMENT LEVER SWEATBAND
K2690-3 6 7 8
ADJUSTMENT LEVER
BOLT 7 ADF MEDIUM VIEW
SPATTER DAMAGE IS NOT COVERED BY WARRANTY: Do not use this product without the correct protective clear cover lenses installed properly on both sides of the Auto-Darkening Filter cartridge (ADF). The cover lenses supplied with this helmet are properly sized to work with this product and substitutions from other suppliers should be avoided.
INSIDE LENS KNOB
ADAPTOR OUTSIDE LENS BEZEL
4
SHELL 1
ADF LARGE VIEW
SWEATBAND
8
6
11
1 1 1
6 HEADGEAR
For Warranty Transactions, contact your local Lincoln Electric distributor. (Ref IMWSI)
1
KP2760-1 L13821 KP2081-5B1 Note 1- Contact Lincoln Electric Service for appropriate replacement.
-----------------------------------------------------------------------------------------------------WARRANTY INFORMATION: Reference IMWS1 included in Literature
1
5
12
2 ADF SMALL VIEW
4 3
ADF stays dark after you stop welding: • The temperature limitations of the ADF have been exceeded. Let the ADF cool down and try not to over heat it again by viewing the arc from the side or at a greater distance. • It may remain dark if you are facing a bright light or the sun. Look away or pass your hand between the sensor and light source. ADF is cracked: • Cease (STOP) using this product if this problem exists. UV/IR protection may be compromised resulting in burns to the eyes or skin. Weld Spatter is Damaging the ADF: • Missing, damaged, broken, cracked or distorted Protective Cover Lens. Replace inside and outside Clear Cover Lenses as needed.
WARNING • Do not use this product if severe spatter damage has occurred to the Auto-Darkening Filter Cartridge or protective clear cover lens. Severe eye damage and burns can result.
REPLACEMENT PARTS ITEM
PART No.
DESCRIPTION
QTY.
1
Note 1
5x4 SHELL, BLACK
1
2 3 4
Note 1 Note 1 KP2796-1 K2690-1
1 1 2 1
5
K2690-2
ADAPTOR BEZEL, BLACK CLEAR POLYCARBONATE LENS ADF 9-13 SHADE CARTRIDGE – SMALL VISTA 1000 ADF 9-13 SHADE CARTRIDGE - MEDIUM VISTA 2000 ADF 9-13 SHADE CARTRIDGE - LARGE VISTA 3000 RATCHET HEADGEAR ADJUSTMENT LEVER SWEATBAND
K2690-3 6 7 8
ADJUSTMENT LEVER
BOLT 7 ADF MEDIUM VIEW
SPATTER DAMAGE IS NOT COVERED BY WARRANTY: Do not use this product without the correct protective clear cover lenses installed properly on both sides of the Auto-Darkening Filter cartridge (ADF). The cover lenses supplied with this helmet are properly sized to work with this product and substitutions from other suppliers should be avoided.
INSIDE LENS KNOB
ADAPTOR OUTSIDE LENS BEZEL
4
SHELL 1
ADF LARGE VIEW
SWEATBAND
8
6
11
1 1 1
6 HEADGEAR
For Warranty Transactions, contact your local Lincoln Electric distributor. (Ref IMWSI)
1
KP2760-1 L13821 KP2081-5B1 Note 1- Contact Lincoln Electric Service for appropriate replacement.
-----------------------------------------------------------------------------------------------------WARRANTY INFORMATION: Reference IMWS1 included in Literature
1
5
12
2 ADF SMALL VIEW
4 3
NOTES
• World's Leader in Welding and Cutting Products • • Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
NOTES
• World's Leader in Welding and Cutting Products • • Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
