Transcript
VIZIT-M440C VIZIT-M440C is a colour monitor intended for use in VIZIT video doorphones.
10
8
9
7 1 6
5
4
3 2
1. Handset 2. DOOR OPEN button 3. Increase value button 4. Decrease value button 5. Preset buttons: - ring tone volume - select ring tone - brightness - saturation 6. LED indicators of a selected preset button 7. Switch to extra camera button 8. MONITOR button 9. Power LED 10. Screen
Figure 1 - Appearance and controls layout PARTS LIST
x1
x1 Operating Instruction
Monitor VIZIT-M440C Fasteners
x3 Screw - 3.5х25
x3 Concrete Insert 6х30
SAFETY INSTRUCTIONS CAUTION! The Monitor does not contain voltage above 27V. Do not perform any connections or repair when the power is on. Take care not to spill any liquids or chemically active substances on the product. Unplug the power supply unit before cleaning the monitor. Clean by wiping with dry soft cloth. Do not use any liquid cleaners, aerosol cleaners or abrasive agents. Do not attempt to service the product by yourself. Please refer all services to qualified service personnel. FEATURES v v v v v v v v v v v v
Colour 3.5” TFT LCD Operation with two doorstations and extra camera (commutator BKM-440 required) Operation with one doorstation, door bell button and extra camera (commutator BKM-440 not required) Calls from doorstation and door bell button Duplex intercom Remote door unlocking with the button Door zone video monitoring Activation of individual / storey doorstation by subscriber (duplex intercom and video monitoring) 5 ring tones, individual ring tone for each doorstation and door bell button. 3 ring volume levels Individual image brightness and saturation for each doorstation and extra camera LED indication of operating modes INSTALLATION 4
1
1
Connecting terminals
2
Recess for cables
3
DC IN to connect power supply unit SA03010029
4
Inlets for cables
5
Socket for handset jack
6
Fixing lugs
6
2
3
Figure 2 - Rear view 4
5
Choose the position for monitor. Recommended altitude is 150 cm from the floor to the monitor center. 1
1
2
85 2 3
85
57
Make 3 holes 1 in the wall. Refer to page 25 for Mounting Pattern. Drive in concrete inserts 2 and screws supplied with your monitor.
3
3
Connect the wires to the terminals of your monitor as shown in Fig. 4-7. Match the monitor’s fixing lugs with the screws in the wall, and hook the monitor on the screws.
Connect the handset to the monitor.
Figure 3 - Installation order
The monitor terminals and their destination are given below :
Terminal LN + LN GND VI1 +E DATA Ec1 Ec2 GND VI2
Destination Intercom line between monitor and commutator /doorstation Ground VIDEO IN from doorstation built-in camera Supply voltage for monitor DATA exchange between monitor and commutator BKM-440 Supply voltage for doorstation built-in camera Supply voltage for extra camera Ground VIDEO IN from extra camera
See Fig. 4 - 7 for the examples of wiring diagrams of the monitor and other doorphone units. Acceptable cross-sections of wires to connect the monitor to the power supply unit, doorstation / control unit (Fig. 4 - 5) are given in the doorstation / control unit operating instructions. Acceptable cross-sections of wires to connect the monitor to the commutator BKM-440 (Fig. 6 - 7) are given in the commutator BKM-440 operating instruction. Note. If the monitor operates together with the commutator BKM-440, a door bell button connection is not available.
EXAMPLES OF WIRING DIAGRAMS DC IN GND
+E VO GND Ec
VI2 MONITOR VIZIT-M440C GND Ec2 Ec1 DATA +E VI1 GND LNLN+
Power Supply SA03010029 18В, 0.5А
Door bell button
Extra Camera 12 V, 0.3 А max
To other apartments
SEL Ek GND LINE -18 +18
Commutator BK-4MV (or BK-4V)
82-Ohm resistor should be connected between the VO and VG terminals of the last commutator in the circuit
LN FD VG V4
LN FC VG V3
LN FB VG V2
VG
V1
LN FA
To next commutators
VI VG VG VO
To doorstation / control unit
Note. Door bell button can be installed near your apartment door, and connected to the GND and DATA terminals of the monitor Figure 4 - Monitor VIZIT-M440C with multi-apartment doorstation and extra camera
VO GND Ec Door bell button
VI2 MONITOR GND VIZIT-M440C Ec2 Ec1 DATA +E VI1 GND LNLN+
Extra Camera 12 V, 0.3 А max LC Ec VO +E GND LINE
Colour
BVD-410CBL
INDIVIDUAL / STOREY DOORSTATION
POWER SUPPLY BPD18/12-1-1 +18 -18 -12 +12
50V 1A
ELECTROMECHANICAL LOCK (R 10 OHM)
Figure 5 - Monitor VIZIT-M440C with individual / storey doorstation and extra camera
Extra Camera 12 V, 0.3 А max
VO GND Ec
VI2 GND Ec2 Ec1 DATA +E VI1 GND LNLN+
Extra Handset
+ -
Main Monitor · Individual / storey doorstation activation · Switching of video channels · Intercom priority over Extra Handset
LN+ LNGND VO1 +E DATA HS+ HSVO2 GND
MONITOR VIZIT-M440C
HS/MON
EQUIV
C COMMUTATOR BKM-440
B INDIVIDUAL / STOREY DOORSTATION
L N1 + LN1GND +E VI1 Ec1 LN2+ LN2GND +E VI2 Ec2
A
BVD-406CB VO VG LN GND +E Ec LC
-18 +18
COMMUTATOR BK-4MV (or BK-4V)
LN FD VG V4
LN FC VG V3
VG
V1
LN FA
SEL Ek GND LINE
LN FB VG V2
To other apartments
To next commutators
+12 -12 -18 +18
VI VG VG VO
82-Ohm resistor should be connected between the VO and VG terminals of the last commutator in the circuit
POWER SUPPLY BPD18/12-1-1
ELECTROMECHANICAL LOCK (R 10 OHM)
50V 1A
To multi-apartment doorstation / control unit
Figure 6 - Monitor VIZIT-M440C (as the main device) with multi-apartment doorstation, individual / storey doorstation and extra camera
MONITOR DATA TERMINAL +E VIZIT-MT460CM VI
MONITOR
GND LNLN+
AWAY REC
LN+ LNGND VO1 +E DATA HS+ HSVO2 GND
MENU
Main Monitor
HS/MON
LN+ VIZIT-M440C LNGND VI1 +E DATA Ec1 Ec2 GND VI2
EQUIV
C COMMUTATOR BKM-440
A
Extra Monitor · Individual / storey doorstation activation - N/A · Switching of video channels - N/A
B
L N1 + LN1GND +E VI1 Ec1 LN2+ LN2GND +E VI2 Ec2
· Individual / storey doorstation activation · Switching of video channels · Intercom priority over Extra Monitor
INDIVIDUAL / STOREY DOORSTATION
INDIVIDUAL / STOREY DOORSTATION
BVD-401СВ BVD-406CB LN GND +E VO Ec LС
VO VG LN GND +E Ec LC
50V 1A
+12 -12 -18 +18
POWER SUPPLY BPD18/12-1-1
ELECTROMECHANICAL LOCK (R 10 OHM)
50V 1A
+12 -12 -18 +18
ELECTROMECHANICAL LOCK (R 10 OHM)
POWER SUPPLY BPD18/12-1-1
Figure 7 - Monitor VIZIT-M440C (as extra device) with two individual / storey doorstations
SETUP Before turning the power on, make sure that there is no misconnection or risk of short circuit. § Turn on the power supply unit or commutator BKM-440. The monitor Power LED (see Fig.1) illuminates with green light. If the Power LED is dim, the monitor is in the sleep mode (calls are ignored, and all buttons except for are disabled). To switch the monitor on, press the button. § Select a ring tone, set its volume, adjust brightness and saturation of colour image from doorstation camera. Press
. Image from the doorstation camera appears on the screen. Press one of the preset buttons: to set the ring tone volume; to select new ring tone; to adjust image brightness; to adjust image saturation. When you press the button, its LED indicator illuminates to show which setting is now active. Setting the ring tone volume (3 levels). Press . LED indicator illuminates. Press to decrease or to increase volume. Every time you press either or , the test sound rings to present the volume level, and the LED is blinking. When the lowest or the highest level is reached, LED blinking stops. Selecting a new ring tone (one of five). Press . LED indicator illuminates. Press selected ring tone sounds.
or
to select a new ring tone. Every time you press either
or
, the
Adjusting image brightness Press . LED indicator illuminates. Press or brightness is reached, the LED blinking stops.
. The LED is blinking. When the lowest or the highest degree of
Adjusting colour image saturation Press . LED indicator illuminates. Press or saturation is reached, the LED blinking stops.
. The LED is blinking. When the lowest or the highest degree of
Quitting Setup Mode 1. To quit the setup mode immediately, pick up the handset and hang it up again. The screen shuts off. 2. The monitor quits the setup mode automatically in 15 seconds of idle, if you do not press for 15 seconds.
,
,
,
,
or
buttons
§ If an extra camera and ordinary door bell button are connected to your monitor (see Fig. 4, 5), you can set an individual ring tone for calls from the door bell button, and image brightness and saturation for the extra outdoor camera. Note, that the ring tone volume remains the same for both the doorstation and door bell button. Press , then . Image from the extra camera appears on the screen. Select a ring tone, set image brightness and saturation, as described above. § If two doorstations are connected to your monitor via BKM-440, and used as the main device (see Fig. 6), you can set an individual ring tone, image brightness and saturation for calls from both doorstations. The ring tone volume remains the same for both doorstations. Press the button, image from the first (i.e. main entrance) doorstation appears in the monitor. Perform the settings as described above. Press the button once more, image from the second (individual/storey) doorstation appears on the screen. Perform the settings as described above. Note § If your monitor is connected to two doorstations via BKM-440, and used as an extra device (see Fig. 7), individual settings for doorstations are not available, they remain the same for both doorstations. To adjust current settings of the monitor as extra device, make a call from one of the connected doorstations. Image arrears on the screen. Select a ring tone, set its volume, set image brightness and saturation, as described above.
FUNCTIONAL CHECK AND OPERATION ORDER When a call is made from the doorstation, the monitor rings. Image from the doorstation camera appears on the screen. Pick up the handset and check duplex intercom. During intercom, press to view image from the extra camera (see Fig. 4, 5, 6), if needed. Press again to switch back to the image from the doorstation camera. To release the door lock, press and hold until the beep. The door is unlocked now. After you release the intercom is still available. Hang up the handset. The screen shuts off, the monitor goes to the Stand-By mode. Note. You can unlock the door without picking up the handset. When called, just press and hold door is unlocked now . After you release , the monitor goes to the Stand-By mode.
button,
until the beep. The
To activate the individual / storey doorstation (i.e. start intercom and video monitoring on your initiative, see Fig. 5), pick up the handset. Image appears on the screen, intercom is available. You can press to view image from the extra camera, if needed. Press again to switch back to the image from the doorstation camera. At pressing the door bell button, the monitor rings, image from the extra camera appears on the screen (see Fig. 4, 5). To engage the sleep mode, press
and hold until the Power LED turns off.
Special notes on operation with BKM-440 The monitor can be connected to the BKM-440 either as the main (see Fig. 6) or the extra monitor (see Fig. 7). The main monitor has an intercom priority over any extra device, i.e. when you pick up the main monitor’s handset, the extra monitor (or extra apartment handset) is disengaged. The extra monitor cannot activate the individual / storey doorstation. To view the door zone in front of main entrance doorstation (see Fig. 6), press on the main monitor, or pick up its handset. To switch to viewing the door zone in front of individual / storey doorstation, press again. To start intercom with the individual / storey doorstation, pick up the handset. SPECIFICATIONS Screen Colour system Video IN: - impedance - voltage Operating voltage Power consumption Dimensions (W)x(H)x(D) Weight
3.5” (89mm) TFT LCD PAL 470 Ohm 1…1.8 V p-p 15…27 VDC 3 W max. 140 x 183 x 48 mm 0.6 kg OPERATING CONDITIONS
Ambient temperature range Relative humidity of air
+5°C to +40°C up to 93% at +25°C
