Transcript
VM-WA525-E / VM-WA65-E VM-WA8-E ELUX SERIES 2-WAY HIGH FIDELITY IN-WALL SPEAKER
Congratulations on your purchase of an Elux Series product from VM Audio. You have seen that with years of acquired taste for quality, the Elux Series has the right design and performance to satisfy your utmost demand. With music so clear and rich and bass so low and loud, you will be immersed in a world of musical euphoria that anything else will seem like white noise. By following the installation instructions carefully, you will ensure yourself performance that will be enjoyed from each use for years to come. Reward yourself with the finer things in life.
Safety Precautions Package Contents Please review the contents of the package and make sure you have received all the items included with your system. (1) (1) (1) (1) (1)
2-Way Component Loudspeaker Removable Speaker Grille Acoustic Foam Grille Insert Cutout Template User Guide
CAUTION RISK OF ELECTIC SHOCK DO NOT OPEN
CAUTION
CAUTION
RISK OF ELECTIC SHOCK DO NOT OPEN
1. Please read these instructions carefully before attempting to install and operate this product. 2. Keep this User Guide for future reference.
Features
3. Save all packaging in the event this product needs to be returned for service or replacement. 4. Ensure to setup your system in a safe and secure manner.
• 2-Way High Fidelity In-Wall Speaker
5. Do not expose the loudspeaker to rain, moisture, or dripping liquids.
• Multi-Component Loudspeaker Design
6. Protect the speaker wires from getting exposed.
• Ballistic Lightweight Fiber Glass Yellow Cone
7. Before placing and installing this loudspeaker product, inspect all hardware, brackets, surfaces, and associated equipment for damage. If a fault is discovered, it should be corrected immediately.
• High Compliance Half-Roll Black Rubber Surround • Low-Resistivity Multi-Layer Round Copper Voice Coil • Multi-Roll Radial Motion Stabilizing Poly Cotton Spider • Dense One-Piece Solid Coated Steel Speaker Frame • Efficient Low-Loss CAD Magnetic Motor Structure • Precision Mylar Dome Tweeter • Spring-Loaded Bare Wire Speaker Connector • Dedicated Built-In 2-Way Second Order Crossover Filter
8. Do not attempt to service this unit, refer all servicing to qualified service personnel. 9. This loudspeaker can easily reproduce sound pressure levels (SPL) loud enough to cause permanent ear damage that could result in hearing loss. Take great precaution to protect yourself from prolonged exposure to high output sound pressure levels.
• Paint-Ready Rectangle ABS Mounting Flange Baffle • Screw-In Quick Locking Arm System
2
3
Getting Started
Installation
Installation • In-wall installation should be located directly above the listening area. In rooms larger than the bathroom or closet, it is recommended to install additional speakers for improved performance. • You may install a bracket where you will be placing the speaker prior to installing drywall. Once insulation and drywall is installed, you may cut the speaker hole.
1. Choose a location in your home to setup your new VM Audio in-wall speakers.
• Use a stud-finder to locate the nearest wood or metal stud and keep in mind the baffle flange will protrude outside of the mounting hole.
Painting The Wall Speakers • It is recommended to paint your speaker before installing into your wall, or reverse the steps of installation to remove the speaker for easy painting. For painting the installed speaker, please use the paint mask in place of the grille. If painting the grille, do not paint while attached to the speaker, and be careful to not clog the holes, which will decrease sound quality. VM Audio recommends only light spray painting.
2. Using the included template, position and outline the hole on the wall.
Power Requirements • For non-distorted high output performance, use an amplifier with the same power rating as the loudspeaker.
Speaker Wires • When running long lengths of speaker wires, it is recommended that higher gauge wire (14 Ga or higher) is always used throughout the wiring.
4
3. Cut the drawn hole using a drywall saw.
5
Installation
Installation
4. Prepare the cables and run them to the speaker and amplifier locations.
5. Remove the speaker grille from the speaker baffle.
8. While holding the speaker in place with one hand, place the Phillips screwdriver into the screw head and rotate clockwise to tighten all four locking arms on to the wall.
6. Push each speaker terminal to insert and connect the positive and negative speaker wires.
6
7. Place the speaker into the mounting hole on the wall and with one hand hold the speaker in place.
9. Cover the speaker by attaching the grille back into the speaker baffle.
7
Table of Contents Troubleshooting No Sound
Table of Contents Specifications VM-WA525-E
• Check the speaker wires and ensure they have a solid connection to all the speaker terminals on each speaker and on the amplifier or receiver.
Loudspeaker Type
Full Range Component
Low Frequency Driver
5.25” Fiber Glass Cone
Tweeter
1/2” Mylar Dome
• Check that the receiver or amplifier is powered “on” at the mains, is not on “mute”, has no headphones attached and that the channels used for the speakers (usually A or B) is in operation.
Baffle
Rectangle / ABS Material
Frequency Response
71Hz - 20kHz
Sensitivity
89 dB
• Refer to the owner’s guide that came with your receiver or amplifier for troubleshooting guidelines for the unit.
Power (RMS/Peak)
55W / 175W
Impedance
8 ohms
• Most initial problems are connectivity, please try a different connection cable to your in-wall speaker(s) or equipment.
Cutout / Depth
9.57 inches / 2.32 inches
No Sound from One Speaker • Check the “balance” control on your receiver amplifier. • Check all connections and cable to the inoperable speaker. • Disconnect the “working” speaker from the receiver amplifier connection/channel. Switch the cord from the non-operating speaker from its current connection to the “working” speaker connection. If the speaker now works, the problem is your receiver amplifier. • Reconnect as original. Remove the speaker cable at the “working” speaker directly and connect it directly to the non-working speaker. If the speaker now works, the problem is somewhere in the original speaker cable. • If the speaker still does not work the problem is the speaker.
8
VM-WA65-E Loudspeaker Type
Full Range Component
Low Frequency Driver
6.5” Fiber Glass Cone
Tweeter
1/2” Mylar Dome
Baffle
Rectangle / ABS Material
Frequency Response
57Hz - 20kHz
Sensitivity
91 dB
Power (RMS/Peak)
75W / 225W
Impedance
8 ohms
Cutout / Depth
10.71 inches / 2.60 inches
VM-WA8-E Loudspeaker Type
Full Range Component
Low Frequency Driver
8” Fiber Glass Cone
Tweeter
1” Silk Dome
Baffle
Rectangle / ABS Material
Frequency Response
50Hz - 20kHz
Sensitivity
92 dB
Power (RMS/Peak)
90W / 270W
Impedance
8 ohms
Cutout / Depth
12.68 inches / 3.54 inches
9
Limited Warranty Agreement Your product is covered by a limited warranty by VM Audio as established below: Electronics Limited Warranty Products purchased from an Authorized VM Audio Dealer are warranted to be free of defects in material and workmanship for one (1) year from the date of original purchase under normal usage. Products that are identified as “refurbished” have a limited warranty of ninety (90) days from the date of original purchase. Dated proof of purchase (original receipt or invoice) will be required for all warranty claims. In the unlikely event that you experienced a manufacturing defect or malfunction during the warranty period, VM Audio will repair the defective product or replace with the same or equivalent product if the same item is not available or discontinued. Replacement product may have superficial blemishes or scratches that do not affect the performance of the product. This warranty is only intended and valid for the original purchaser and cannot be extended to subsequent owners. Any applicable implied warranties are limited to the period of the expressed warranty starting from the original purchase date. No warranties, expressed or implied, will be accepted after the previously listed periods. Exclusions may apply; please check your local state laws. Instructions for Claiming Warranty Service If you should require warranty service, please return the product to the Authorized VM Audio Dealer you originally purchased the item for an experienced and speedy claim of your warranty service. Contact VM Audio directly to find the Authorized Dealers nearest you. In the case the defective merchandise needs to be returned to VM Audio, please contact us and a Return Merchandise Authorization (RMA) number will be assigned. It is important to pack all defective items in the original packaging to prevent damages from shipping, and be sure to write the RMA number clearly on the outside of the box for faster processing. Do not include non-defective items as it is not necessary and will increase your shipping costs.
10
Limited Warranty Agreement Include a copy of the original receipt or invoice with the purchase date, dealer’s name, customer’s name and invoice number clearly visible. Manufacturing date may be used if no proof of purchase is provided. The customer will pay to ship the defective product; COD will not be accepted. Please follow the above instructions carefully to prevent voiding your warranty. Your Warranty Service Does Not Cover the Following: - Products not purchased from an Authorized VM Audio Dealer - Damages from poor installation by not following the included instruction manual. - Damages due to excessive moisture, heat and other elements from improper care. - Evidence of tampering or repair by non-authorized personnel. - Products not issued an RMA number. - Damage during freight from poor packaging or handling. - Return shipping on non-defective items. Warranty Turnaround Time It is VM Audio’s goal to turnaround the merchandise in a timely fashion of 1 week. Unexpected delays may occur due to repair parts or replacement shortage. International Warranty Please check with your Authorized International VM Audio Dealer or distributor for specific warranty policies and process for your country.
11
