Transcript
W-FI DXM SYSTEM
Order code: BOTE65
WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP!
CAUTION! Keep this equipment away from rain, moisture and liquids.
SAFETY INSTRUCTIONS Every person involved with the installation, operation & maintenance of this equipment should: - Be competent - Follow the instructions of this manual
CAUTION! TAKE CARE USING THIS EQUIPMENT! HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!
Before your initial start-up, please make sure that there is no damage caused during transportation. Should there be any, consult your dealer and do not use the equipment. To maintain the equipment in good working condition and to ensure safe operation, it is necessary for the user to follow the safety instructions and warning notes written in this manual. Please note that damages caused by user modifications to this equipment are not subject to warranty.
1
IMPORTANT: The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorised modification to the equipment.
• Never let the power-cable come into contact with other cables. Handle the power-cable and all mains voltage connections with particular caution! • Never remove warning or informative labels from the equipment. • Do not open the equipment and do not modify the equipment. • Only use the equipment indoors. • Do not expose to flammable sources, liquids or gases. • Always disconnect the power from the mains when equipment is not in use or before cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the power-cable. • Make sure that the available voltage is between 220v/240v. • Make sure that the power-cable is never crimped or damaged. Check the equipment and the power-cable periodically. • If the equipment is dropped or damaged, disconnect the mains power supply immediately. Have a qualified engineer inspect the equipment before operating again. • If the equipment has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation might damage the equipment. Leave the equipment switched off until it has reached room temperature. • If your product fails to function correctly, discontinue use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Prolight dealer for service. • Only use fuses of same type and rating. • Repairs, servicing and power connection must only be carried out by a qualified technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS. • WARRANTY; One year from date of purchase.
OPERATING DETERMINATIONS If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and the warranty becomes void. Incorrect operation may lead to danger e.g. short-circuit, burns and electric shocks etc. Do not endanger your own safety and the safety of others! Incorrect installation or use can cause serious damage to people and property.
2
Identification:
1, Antenna SMA Connector 2, DC Input Connector 3, DMX Signal Indicator 4, Wireless Remote Indicator: Signal receipt (Red), Signal Emission (Green) Overview:
5, Dip switches 1-4 (pairing) 6, Dip switches 1-6 (freq + tx, rx) 7, DMX In Socket 8, DMX Out Socket
The W-FI Wireless DMX controller enables you to communicate with your DMX fixtures without the need for long cable runs between controllers and fixtures. The W-FI can act as both Transmitter or Receiver so all units are identical. During set-up you have to assign one as the Transmitter and a second or more units as the Receiver. The W-FI has a communication range of up to 300M depending on the local environment. Operating instructions: ASSIGN A UNIT TO BE THE TRANSMITTER. With the power disconnected set dip switch 6 on the bottom row of dip switches to the “ON” position. Now using dip switches 1-5 on the same set of dip switches you can select the frequency you require (see frequency chart). Finally you need to set a pairing code on the top set of dip switches. You can select any code you wish as long as you set the Receiving unit to the same code. You can now plug the DMX into the Transmitter and power up your W-FI. You should now have the Red DMX LED flashing to show you have a DMX signal from your desk, you should also have the Green transmit LED illuminated. YOU NOW NEED TO ASSIGN THE RECEIVER. With the power disconnected set dip switch 6 to “OFF” now using dip switches 1-5 set the Receiver to the same frequency as the Transmitter, now set the pairing code the same as the Transmitter. Connect the DMX output to your fixtures, you can now power up the Receiver. You should now have the Red DMX LED flashing to show that it is receiving DMX, you should also have the Red receive LED illuminated. Your system is now ready for use.
3
The Wireless DMX controller can work on 32 selectable frequencies.
0 = Off 1 = On
4
The Wireless DMX controller frequency table continued.
0 = Off 1 = On Working environments and cautions: 1, The transmitter and receiver controller must be on the same frequency and address. 2, The transmitter and receiver antenna must be vertical to the controller to ensure better signal transfer.
5
Features: Transmit/receive up to 512 DMX channels wirelessly Use with any universal DMX-512 controller Frequency: 2.4G Working frequency: 2400M ~ 2431M (2.4G ISM) Transmission power: 20DBM Durable, extruded aluminium casing Functions as transmitter or receiver 300m Transmission range (Max) Requires two units for operation Specifications: Power supply: DC 9V~500mA by adaptor (included) Dimensions: 196 x 93 x 53mm (excluding antenna) Weight: 0.50Kgs
6
