Transcript
Warranty Card Name: Company Name: Address: Ph:
Fax:
E-mail: Purchased From: Date Purchased: Product Purchased: (Model No.) Return Authority Number: Please Note: Proof of purchase will be required for all warranty claims. **Refer to the full warranty statement at www.matson.com.au
Matson Automotive Industries Pty Ltd 100 Links Road StMary’s NSW 2760 + 61 2 98333 444 www.matson.com.au
[email protected]
CODES: Explosive gases may escape from the battery during charging. Prevent
Light / Code
Fault / Condition
Solution
Diagnosis light ON
Charger is diagnosing battery condition
Charge light ON
Battery is charging
Charged light ON
Battery is fully charged and operating in float mode
This appliance requires an earthed 240Volt mains supply.
Equalizing light ON
Battery is equalizing
This appliance is not for use with non-rechargeable batteries.
F01
Bad cells in battery
Replace battery
F02
Charge time exceeds 48 hours
Bad cells in battery, replace battery
F03
Reverse connection
Check clamps for correct polarity
F04
Overheating
Charger will start again when temperature drops, ensure vent is clear of obstruction
F05
Aging battery
Battery can no longer be efficiently charged, replace battery
F06 (IR61224 only)
Incorrect voltage setting
Correctly set charge rate
F00
Standby, awaiting instructions / input
flames and sparks. Ensure area is well ventilated. Before charging ensure you have read the instruction manual in full. This appliance is for USE INDOORS. Do not expose to rain. For charging 6 / 12 / and 24 volt batteries. Disconnect from 240Volt supply before making or disconnecting
connections to the battery.
Never charge a frozen battery. In the event of the AC cord becoming damaged it must be replaced by a
qualified electrician. Corrosive gasses may escape during the charging process, ensure charger
is placed well away from battery. This appliance is intended for use by responsible persons and should not
be operated by children. Always check battery manufacturers specifications on charge rates and
voltage prior to charging.
FEATURES: 7 Stage Automatic Charging The Matson INFINITE range of battery chargers are fully automatic 7 stage. Automatic chargers prevent your battery from being overcharged and consequently becoming damaged. The INFINITE range of chargers can be connected to the battery indefinitely. INFINITE chargers can be programmed for different battery types including GEL, AGM, Deep Cycle, Sealed Lead Acid and Calcium batteries. Some models in the range can have variable Voltage outputs. INFINITE chargers have a unique inbuilt diagnosis program. On connection to the battery the charger will automatically diagnose the batteries condition and change its charge rate and charge stages accordingly. This function will optimise charging conditions and extend battery life. Aluminium housing Full LED display : voltage, current, battery capacity and alternator % Electronic touch-button controls Chemistry selection: Sealed lead acid / GEL / Deep Cycle / Calcium Desulphation stage Microprocessor controlled High frequency charging for efficiency Polarity protection. Prevents output leads from sparking due to reverse
connection or short circuit. Over temperature protection. Fan cooled internals with set cut off point for
additional safety. Over current protection. Charger will automatically reduce current for
optimum battery condition.
CHARGING INSTRUCTIONS:
Model No:
IR12
IR24
IR61224
Type
7 stage
7 stage
7 stage
Input
240VAC 50Hz
240VAC 50Hz
240VAC 50Hz
quired for sealed lead acid and maintenance free batteries). Top up with Matson
Output Voltage
12Volt DC
24 Volt DC
6/12/24 Volt DC
distilled water if need and replace vent caps
Output current
2 ~ 24Amp Selectable / variable
1 ~ 12Amp Selectable / variable
6/12Volt 2/10/20Amp 24Volt 2/5/10 Amp Selectable
Minimum Start Volt
1.5Volt
1.5Volt
Check liquid level in battery. Before attempting to charge the battery remove vent caps and check liquid level (not re-
Charging a battery not in a vehicle: Ensure 240Volt power supply is OFF.
1.5Volt
Connect black (negative) charging clamp to negative battery post. Connect red (positive) charging clamp to positive battery post.
CHARGE CONTROL
Turn on 240Volt power source. Desulphation
High Frequency Pulse Charge (DEPENDENT ON DIAGNOSIS)
Set battery type. (Chemistry selection) Set battery voltage (IR61224 only)
Soft Start
Yes
Yes
Yes
Bulk Charge
14.1V (Gel) 14.7V (SLA) 15.1V (Calcium)
14.1V (Gel) 14.7V (SLA) 15.1V (Calcium)
14.1V (Gel) 14.7V (SLA) 15.1V (Calcium)
Absorption
Constant voltage with Constant voltage with Constant voltage with automatic Amperage automatic Amperage automatic Amperage control control control
Position input cable and output cable away from risk ie: fans, bonnet or door
Equalization
Automatic
In this case connect red (positive) charge clamp to positive terminal of battery
Analysis
Automatically detects faulty batteries. Error code signifies fault
Recondition
Constant current automatically varied
Float
13.7V
Automatic
13.7V
Select charge rate. (Amperage output)
Charging a battery in a vehicle: Most vehicles in Australia are negative earth (black cable to chassis of vehicle)
Automatic
Connect black (negative) charge clamp to chassis of vehicle away from any moving parts Turn on 240Volt power source Set battery type. (Chemistry selection)
13.7V
Set battery voltage (IR61224 only)
BATTERY RANGE
Select charge rate. (Amperage output)
Deep Cycle
10 ~ 240Ah
10 ~ 240Ah
10 ~ 240Ah
Automotive
150 ~ 800CCA
150 ~ 800CCA
150 ~ 800CCA
**Note: on model numbers IR12 and IR24 the set amperage may drop as the charger diagnoses the battery condition and reduces output to optimise battery condition
Disconnecting the charger: Ensure 240Volt mains supply is turned off and removed from power socket Remove black (negative) charger clamp from battery post or vehicle chassis Remove red (positive ) charger clamp from battery post.
