Transcript
WATER SYSTEMS
1. 2. 3. 4.
Carbonators and Accessories Water Boosters and Accessories Water Filtration Systems and Replacement Filters Water Bottle Dispensing System
Lancer Carbonators and Components Known for its superior quality and reliability, the Turbo heavy duty, high capacity carbonator has a 100 GPH (379 LPH) pump, ideal for fast flow valves. With 60˚ F inlet water it will provide a carbonation level of 6.0. With 75˚ F inlet water it will provide a carbonation level of 5.5, and at maximum flow 5.3. Turbo has solid state electronics, a built-in advanced diagnostics system, ASSE approved vented check valve, stainless steel base with rubber feet, 3/8" male barb inlets and dual 3/8" male flare soda outlets. Dimensions: 12.25"W x 12.5" H x 14.25" D. Shipping weight: 35 lbs.
Part Number
Description
85192300
Carbonator, fast flow with vented check valve (VCV)
85192701
Carbonator, recirculating system
520590/01
Probe assembly, fast flow, Turbo
520206
Probe assembly, universal
64500054
Liquid level control board, universal
520001
Proximity switch assembly
540007/01
Carbonation tester kit
520590/01
Lancer Turbo carbonator
520206
64500054
520001
540007/01
SHURflo High Pressure Electric Carbonator 8005 Series, positive displacement, open flow, 3 chamber diaphragm pump is self-priming and can run dry without damage. Comes with ground wires and base plate. Flow rate: 1.4 GPM. Operating pressure: 100 psi. 115V.
Part Number
Description
8005932260
Carbonator, high pressure, 100 psi, 1.4 GPM Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com
Continuing product improvements may necessitate changes without notice. © 2010 ABS
E-1
WATER SYSTEMS
McCann’s Carbonators and Components McCann’s carbonators produce 100 GPM, have Diamond Bright tanks, brass water pumps, and encapsulated electronics to prevent moisture damage. Base is injection molded with press-in rubber feet to reduce noise. Heat sink probe caps prolong probe life, 2-piece probe design simplifies diagnostics, and there’s no need to shut off the water or CO2 for service. To test the 2-piece float probe: remove the probe electronics, pass the tip of a magnetic screwdriver past the lower end of the tube. If the reed switch closes, it is operating properly. The 2-piece probe has a five year warranty.
E400397
Recirculating cold carb system maintains temperature at 30-33˚ F for optimum carbonation levels, and can be easily retrofit any installed dispenser system. All carbonators are 1/3 HP, 7.0 amps, 115/60/1, have ASSE 1022 backflow preventors, vented check valves, 1/4" MF CO2 inlet, 3/8" MF water inlet and 3/8" MF soda water outlet(s).
Part Number Low Lead
Description
Tank Soda Capacity Outlets
E400397 E480397
Big Mac carbonator
2 gals.
2
32 oz.
1
32 oz.
1
2 gals.
2
436002
13.5" W x 10.5" H x 12.75" D
436002
436802
Standard carbonator 9" W x 11" H x 11.5" D
435602
435802
Carbonator-in-a-box 12.25" W x 15" H x 6.5" D
153127
153127LL
Recirculating cold carb system 25" W x 15" H x 18" D
McCann’s Carbonator Components Part Number
Description
161404
Float and probe assembly
161441
Probe kit and mounting studs
162115
Probe only
051374
2 male prong to 3 female prong adaptor cord/plug
051373
3 female prong cord/plug
152088
Power cord assembly (18/3), 8'
160856
Carb pump saver with lamp
190031
Pressure relief valve for carb tank, 180 psi
000868
Check valve, single, 1/4" MFL
000867
Check valve, double, 1/4" MFL
001217
Carbonator foot (for bases)
435602
E202397 recirculating cold carb system
161404
162115
190031
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com E-2
Continuing product improvements may necessitate changes without notice. © 2010 ABS
WATER SYSTEMS
McCann’s Carbonator Components Continued
Part Number
Description
153100
Water inlet & nut assembly, plastic base
153018
Water inlet tubing assembly, 3/8", ASSE 1022
151319
Carbonator tank assembly, large w probe, 2 out
151318
Carbonator tank assembly w decals, large, 2 out
153095
Carbonator tank assembly, weld complete, 2 out
150538
Carbonator tank, small, 3/8 out, w decals & stud
E400397
Back Flow Preventors A vented backflow preventor will provide pressure relief if the primary check valve fails, ensuring that the secondary check valve will remain closed. Plumbing codes in most states require that a ASSE standard 1022 vented backflow preventer is used on all carbonated beverage dispensers. Those with an internal ASSE 1032 non-vented check valve must have an ASSE 1022 check valve installed on the dispenser water line.
190897
61657
DS470DVV66X
DS470DVV6F6X
DS47066
161522
Part Number
Type
Description
190897
ASSE 1022
ABF-1 brass check valve, low lead
190944
ASSE 1022
ABF-1 brass check valve w 1/8" vent, low lead
61678
ASSE 1022
Watts SD-3 check valve
3/8" MF
61657
ASSE 1022
Watts SD-3 check valve with strainer
3/8" MF
61655
ASSE 1022
Watts SD-2 double check valve
3/8" MF
S2722
ASSE 1022
Vent tube fitting
1/8" barb
161521
ASSE 1022
McCann’s E3000 conversion kit
161522
ASSE 1022
McCann’s E2000 conversion kit
161527
ASSE 1022
McCann’s 43 Series conversion kit
S470DVV66X
ASSE 1032
Double check with vent
3/8" MF
S470DVVP66X
ASSE 1032
Double check with vent
3/8" MPT x 3/8" MF
S470DVV6F6X
ASSE 1032
Double check with vent stem
3/8" MF x 3/8" FF
S470D66
SS Ball
Double ball check valve
3/8" MF
S470DH4H4
SS Ball
Double ball check valve
1/4" barb
S470DFP4P4
SS Ball
Double ball check valve
1/4" FNPT x 1/4" NPT
S47066
SS Ball
Single ball check valve
3/8" MF
S470H6H6
SS Ball
Single ball check valve
3/8" barb
Fitting
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com Continuing product improvements may necessitate changes without notice. © 2010 ABS
E-3
WATER SYSTEMS
Carbonator Pumps Rotary vane pumps move potable water to beverage dispensers. Models with strainers have removable caps for periodic cleaning (every four months under normal conditions). Inlet and outlet ports are 3/8" NPT threaded.
Some states require low or lead-free metals.
The products listed below are the most commonly ordered part numbers. For additional pump options call ABS customer service.
Fluid-O-Tech PA350X
Fluid-O-Tech PA350
Fluid-O-Tech PA310X
Fluid-O-Tech PA801
Procon Series 1
Procon Series 2
Procon Series 3
Procon Series 4
Part Number
Low Lead Part Number
Series Brass or SS GPH PSI
Strainer Bypass Adj./ Brand Releif Valve
PA350X250
PB350X250
PA
111A100F11AA250
Brass
125
250
Yes
Yes
Fluid-O-Tech
111A100F11AA250LL 1
Brass
100
250
Yes
Yes
Procon
111A125F11AA250
111A125F11AA250LL 1
Brass
125
250
Yes
Yes
Procon
PA3501250
PB3501250
Brass
125
250
No
Yes
Fluid-O-Tech
112A100F11AA170
112A100F11AA170LL 2
Brass
100
170
No
Yes
Procon
112A050F11AB100
112A050F11AB100LL 2
Brass
50
100
No
Yes
Procon
112E100F11BA170
112E100F11BA170LL 2
Brass
100
170
No
Yes
Procon
PA110100
PB110100
PA
Stainless Steel
50
100
No
No
Fluid-O-Tech
PA310100
PB310100
PA
Stainless Steel
100
100
No
No
Fluid-O-Tech
113A025F31XX
113A025F31XXLL
3
Stainless Steel
25
N/A
No
No
Procon
PA111100
PB111100
PA
Stainless Steel
50
100
No
Yes
Fluid-O-Tech
PA311100
PB311100
PA
Stainless Steel
100
100
No
Yes
Fluid-O-Tech
113A050F31AB
113A050F31ABLL
3
Stainless Steel
50
100
No
Yes
Procon
113A100F31AA
113A100F31AALL
3
Stainless Steel
100
170
No
Yes
Procon
113A100F31AAT
113A100F31AATLL
3
Stainless Steel
100
170
No
Yes
Procon
PA801240
PB801240
PA
Brass
240
240
Yes
Yes
Fluid-O-Tech
114B240F11BA
114B240F11BALL
4
Brass
240
250
No
Yes
Procon
PA
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com E-4
Continuing product improvements may necessitate changes without notice. © 2010 ABS
WATER SYSTEMS
Carbonation Testers
Part Number
Description
Proper carbonation is critical to soft drink quality. During preventive maintenance several soft drink samples are poured into the chilled tester. Pressure and temperature are recorded and cross-referenced with the table on the canister to determine the current carbonation volume, and whether or not the carbonation needs adjustment.
2701
Pepsi carbonation tester, complete assembly
270110A
Pepsi carbonation tester, thermometer assembly
27013A
Pepsi carbonation tester, relief valve assembly
2701200A
Pepsi carbonation tester, canister assembly
2701A10
Pepsi carbonation tester, cap (must be purchased with gasket)
45001100
Pepsi carbonation tester, gasket with adhesive, for cap
270112
Pepsi carbonation tester, gauge 0-30 psi
600GP
Pepsi carbonation tester, gauge protection boot
540007/01
Lancer carbonation tester, complete assembly
220025
Lancer carbonation tester, thermometer assembly
010767
Lancer carbonation tester, vent valve stem
010768
Lancer carbonation tester, vent cap
010814
Lancer carbonation tester, housing
011013
Lancer carbonation tester, adapter
020108
Lancer carbonation tester, seal
050112/02
Lancer carbonation tester, cap
160050
Lancer carbonation tester, gauge
4406
1/3 HP carbonator motor, welded base, 115V
4805
1/3 HP GE carbonator motor, 115/230V (dual)
101649
1/3 HP carbonator motor, welded base, 8 ft. harness, 115V
101647
1/3 HP carbonator motor, resilient base, 8 ft. harness, 115V
17849
1/3 HP carbonator motor, H682, carb ball bearing
1138
Strainer screen for Series 1 Procon pump
1143
Coupling ring for Procon pump
10451
Pressure spring
G000520
Insulation cover for Series 3 Procon pump
011779W
Insulation cover right side for Series 1 Procon pump
011910
Insulation cover left side for Series 1 Procon pump
161459
Carbonator/water booster floor stand, stainless
161480
Carbonator/water booster wall or rack mount shelf, stainless
CM1FJ
Carbonator/water booster floor stand, black
CM3FJ
Carbonator/water booster wall or rack mount shelf, black
103197
26A Watts water regulator, 3-50 psi, no gauge port, 3/8" FNPT
103200
26A Watts water regulator, 10-125 psi, no gauge port, 3/8" FNPT
0328060
263A Watts water regulator, 0-125 psi, 1/4" MPT gauge port, 3/8" FNPT
67701
5 gallon accumulator tank
Pepsi carbonation tester
Lancer carbonation tester
Carbonator Parts and Accessories
161459
161480
4406
1143
26A
263A
CM1FJ
CM3FJ
67701
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com Continuing product improvements may necessitate changes without notice. © 2010 ABS
E-5
WATER SYSTEMS
Water Booster Systems Water boosters provide consistent water pressure to beverage dispensing systems, ensuring optimum performance.
Gas-Driven Boosters Flojet K56 system has a 1/2 gallon accumulator tank, quick disconnect ports, and exhuast muffler for quiet operation. It is self-priming, supplies up to 4 GPM, and operates 60-90 psi. Dimensions: 12" H x 11.5" W x 7" D. 1 year warranty. Flojet G56 pump operates quietly and supplies up to 4 GPM. If pumping over 1.7 GPM a pulsation dampener or accumulator tank should be used to reduce pulsation due to momentary shifts in flow requirements. Operates 20-90 psi. Dimensions: 5.27" H x 3.21" W x 4.58" D. Weight: 1.24 lbs. 1 year warranty.
G56 pump
Product Outlet
K56 system
Part Number
Description
Product Inlet
Gas Inlet
K561030A
K56 water boost system w 1/2 gal tank
1/2" barbed straight plastic 1/2" barbed straight nylon
G561215A
G56 water pump, stand-alone or replacement pump for K56 system
1/2" barbed straight plastic 1/2" barbed straight plastic 1/4" CO2 shutoff brass
20793100
G56 pump muffler port
N/A
N/A
N/A
20799100
K56 1/2 gallon bladder tank
N/A
N/A
N/A
1/4" CO2 shutoff brass
Fully Automatic Electric Boosters Typically used when pumping from a cistern, water storage tank, or other ground water source. Both 2820 and 2840 Series have an accumulator tank, built-in inlet strainers, pressure switches and check valves. Dimensions: 11" W x 7" H x 11.5" D. 115V. 1 year warranty.
2820 and 2840 system
Part Number
Description
Product Inlet/Outlet
PSI
GPM
2820040A
2820 Series, 115V
3/8" FPT
0-70
1.5
2840010A
2840 Series, 115V
1/2" OD or 3/4" OD hose barb
0-40
3.5
2840000A
2840 Series, 115V
1/2" OD or 3/4" OD hose barb
0-40
4.5
2840100A
2840 Series, 24V
1/2" OD or 3/4" OD hose barb
0-45
4.5
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com E-6
Continuing product improvements may necessitate changes without notice. © 2010 ABS
WATER SYSTEMS
Triplex Water Booster System Triplex has a 4 gallon stainless steel tank, provides 1.4 GPM, and up to 100 psi outlet. Its advanced pump technology provides high efficiency, increased drawdown time, and extended life. If the inlet pressure exceeds 30 psi the pump requires a 30 psi water regulator. Operating temperature: 40˚-120˚ F. Pump inlet: 3/8" hose barb. Tank discharge port: 1/2" hose barb. 115V.
Triplex Water Booster/Water Delivery Pumps The Triplex High Pressure diaphragm pumps are self-priming and can run dry without harm. They are intended for intermittent duty cycles but can be run continuously for short periods of time. If the inlet pressure exceeds 30 psi the pump requires a 30 psi water regulator. 115V. 1 year warranty.
Duplex II Water Booster/Water Delivery Pumps The self-priming Duplex II Series with new diaphragm design, new valves, built-in back flow preventer, heavy-duty ball bearings and motor have been designed for maximum efficiency and long life. 115V.
AC Variable Speed Drive (VCD) Pumps The AC VCD constant pressure pump matches motor speed to system demand to provide stable flow and reduced amp draw, eliminating unwanted pump switch cycling and the need for an accumulator tank. If the inlet pressure exceeds 30 psi the pump requires a 30 psi water regulator. 115V. 1 year warranty.
Part Number
Description
Water Inlet
Water Outlet
PSI
GPM
2830000A
Triplex booster system
3/8" barb
1/2" barb
100
1.4
03710042A
Triplex Series
3/8" FPT
3/8" FPT
100
1.4
03810042A
Triplex Series
3/8" FPT
3/8" FPT
150
1.4
D4821H4011A
Duplex II Series
3/8" FPT
3/8" FPT
45
2.2
D4831H5011A
Duplex II Series
3/8" FPT
3/8" FPT
60
2.2
D4834H6011A
Duplex II Series
3/8" FPT
3/8" FPT
80
2.2
D4834H7011A
Duplex II Series
3/8" FPT
3/8" FPT
100
2.2
04524043A
AC VCD with 3 wires
5.0
04524500A
AC VCD cable with plug
5.0
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com Continuing product improvements may necessitate changes without notice. © 2010 ABS
E-7
WATER SYSTEMS
Flojet Water Booster Accessories Part Number 01752300C 01752302C 01752320C 01752322C 188100000 20799000A 30573001 305730002B 305730012B
Description Inline water regulator, 50 psi, QD connect, no ports Inline water regulator, 50 psi, QD connect, 3/8" hose barb ports Inline water regulator, 30 psi, QD connect, no ports Inline water regulator, 30 psi, QD connect 3/8" hose barb ports Accumulator tank, 1 gallon, 3/4" MPT openings, no fittings Accumulator tank, .60 gallon, 3/4" MPT openings, no fittings Accumulator tank, 125 psi,1 quart/liter capacity, 1/2" barb fittings Accumulator tank, rubber valve, 125 psi, 1/2 quart/liter capacity, 1/2" barb fittings Accumulator tank, metal valve, 125 psi, 1/2 quart/liter capacity, 1/2" barb fittings
20381002 20381026
30573001
305730002B/ 305730012B
Inline water regulators
Flojet Water Booster/Pump Fittings
21000131A 21000130A
188100000/ 20799000A
20381009 20371024
21000229B 21000228B
91010004 91010053
Part Number Application Pump Series
Barb Size
Shape
Material
21000131A 21000130A 20381002 20381026 20381009 20381024 21000228B 21000229B 21000230B 91010002 91010004 91010006 91010032 91010053 91010001 91010003 91010005 91010033 91010052
1/4" 3/8" 1/2" 1/2"-3/8" 1/2" 1/2"-3/8" 1/4" 3/8" 1/2" 3/8" x 3/8" 1/4" x 3/8" 3/8" x 1/2" 3/8" x 1/4" 1/4" x 1/4" 3/8" x 3/8" 1/4" x 3/8" 3/8" x 1/2" 3/8" x 1/4" 1/4" x 1/4"
Straight hose barb Straight hose barb Straight hose barb Straight hose barb Elbow hose barb Elbow hose barb Straight Straight Straight Straight, MPT x barb Straight, MPT x barb Straight, MPT x barb Straight, MPT x barb Straight, MPT x barb Elbow, MPT x barb Elbow, MPT x barb Elbow, MPT x barb Elbow, MPT x barb Elbow, MPT x barb
Stainless steel Stainless steel Plastic/Celcon Plastic/Celcon Plastic/Celcon Plastic/Celcon Plastic Plastic Plastic Plastic Plastic Plastic Plastic Plastic Plastic Plastic Plastic Plastic Plastic
Inlet/Outlet Inlet/Outlet Inlet/Outlet Inlet/Outlet Inlet/Outlet Inlet/Outlet Inlet/Outlet Inlet/Outlet Inlet/Outlet Inlet/Outlet Inlet/Outlet Inlet/Outlet Inlet/Outlet Inlet/Outlet Inlet/Outlet Inlet/Outlet Inlet/Outlet Inlet/Outlet Inlet/Outlet
G56 & K56 G56 & K56 G56 & K56 G56 & K56 G56 & K56 G56 & K56 G56 & K56 G56 & K56 G56 & K56 Duplex II & 2820 Duplex II & 2820 Duplex II & 2820 Duplex II & 2820 Duplex II & 2820 Duplex II & 2820 Duplex II & 2820 Duplex II & 2820 Duplex II & 2820 Duplex II & 2820
91010003 91010052
Additional Info
John Guest John Guest John Guest
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com E-8
Continuing product improvements may necessitate changes without notice. © 2010 ABS
WATER SYSTEMS
McCann’s Water Boosters McCann’s electric water boosters have stainless steel tanks and fittings, pre-charged bladders and relief valves. Flow rates up to 100 GPH. Minimum inlet pressure: 20 psi. Outlet pressure switch: 80-100 psi. 115V. Standard water boosters have a 1/3 HP motor, 100 GPH brass rotary vane pump and single ball check valve. Economy water boosters have a 100 GPH Aquatec motor and pump combination.
Part Number Model
Tank
162173
Standard
4 gallon
3/8" / 1/2"
168173
Standard
4 gallon
3/8" / 1/2"
Low lead brass
162172
Standard
4 gallon
3/8" / 1/2"
CC
168172
Standard
4 gallon
3/8" / 1/2"
Low lead brass, CC
162171
Standard
2 gallon
3/8" / 1/2"
162171
Standard
2 gallon
3/8" / 1/2"
Low lead brass
162170
Standard
2 gallon
3/8" / 1/2"
CC
168170
Standard
2 gallon
3/8" / 1/2"
Low lead brass, CC
1631723/8
Economy
2 gallon
3/8"
1631721/2
Economy
2 gallon
1/2"
1631743/8
Economy
4 gallon
3/8"
1631741/2
Economy
4 gallon
1/2"
Standard model
Inlet/Outlet Additional Information
Economy model
McCann’s Water Booster Parts and Accessories Part Number
Description
161473
Pressure switch and cord assembly for all McCann’s boosters
111A100F11AA250
Rotary vane pump for 162171 or 162172
4406
Motor for 162171 or 162172
160166
Aquatec motor for 163172, 163173 or 163174
4406
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com Continuing product improvements may necessitate changes without notice. © 2010 ABS
E-9
WATER SYSTEMS
SHURflo Electric Water Booster Systems All booster systems include a mountable base, 30 psi water regulator and pump cord. The Mini has a plastic accumulator tank. The Medium and Maxi booster systems have a stainless steel tank. 115V. Mini
Maxi
Medium
Part Number
Description
GPM
Tank PSI
Water Inlet/Outlet
804001
Mini boost system w mounting board
21 oz. 60 psi 3/8" metal barb
804002
Mini boost system w mounting board
21 oz. 90 psi 3/8" metal barb
804023
Medium “E” boost system w side mount, quick disconnect pump ports, replaceable tank bladder
1.6
2 gal
90 psi 3/8" metal barb
804023SV
Medium “E” boost system w side mount, quick disconnect pump ports, replaceable tank bladder, SHURlock shut-off ball valve
1.6
2 gal
90 psi 3/8" metal barb
804037
Maxi boost system, 3/8" inlet/outlet
1.6
6 gal
90 psi 3/8" metal barb
804026
Maxi boost system, 1/2" inlet/outlet
1.6
6 gal
90 psi 1/2" metal barb
SHURflo Electric Water Pumps Positive displacement 3 chamber diaphragm water delivery pumps are self-priming, and can run dry without damage. Pumps include ground wires and baseplate. 115V.
8025 Series
2088 Series
8005 Series
Part Number
Description
GPM
PSI
Water Inlet/Outlet
2088594154
Transfer pump
3
45
1/2" MPT
8005733155
Delivery pump
1.4
60
1/2" MPT
8025213236
Standard water boost pump
1.4
60
3/8" FPT
8025933289
Standard water boost pump
1.4
90
3/8" FPT
8025933399
Replacement pump for water boosters: 804023, 804037, 804026
1.6
90
9405300
High flow/high pressure water boost/carbonation pump with two 3 chamber diaphragms
3.8
150
3/8" barb
SHURflo Accumulator Tanks Part Number
Description
Water Inlet/Outlet
181201
21 oz. accumulator tank, metal mounting bracket
1/2" FPT
181400
21 oz. accumulator tank, gas pump QD clip ports
14045
2 gallon stainless steel tank, 1/2" or 3/4" FPT
181201
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com E-10
Continuing product improvements may necessitate changes without notice. © 2010 ABS
WATER SYSTEMS
Water Booster Filter “Combo” Systems Filtered water improves the flavor of soft drinks, increases carbonation, and extends the life of equipment. Boosted water ensures consistent water pressure for consistent brix ratio, maximum flow rate and efficiency. Combining the two systems into one conserves valuable space. SHURflo’s LVPO (Low Volume per Outlet) water boost filtration system is a complete turn-key solution which provides perfect ingredient water to low volume fountain dispensers and ice machines. The LVPO filtration system features: • SHURflo 90 psi, 115 VAC, 8000 Series corded booster pump • 2 gallon stainless steel water accumulator tank • LVPO F-1 “Big Boy” 5 micron carbon block inline filter for particulate, chlorine, taste and odor reduction • Filter can be mounted in any orientation, improving serviceability • Colored coded inlet & outlet filter ports & valves for easy identification of water flow • Quick connect 3/8" barb inlet/outlet ports • Low pressure drop (less than 8 psi at 3.0 gpm) • 50 psi pre-charge recommended for most beverage applications
SHURlock Fittings (1/2" FPT straight & elbow available) 3/8" barb
WB2LVPO01 is designed for single fountain dispensers that serve less than 500 gals. of syrup per year. Service life of filter: 6,000 gal. @ 3.0 GPM.
WB2LVPO02 has two filters; one that pressurizes and filters the water to a single dispenser that serves less than 500 gals. of syrup per year, and one that provides nonboosted treated water to the ice-maker. LVPO-F-1 (fountain filter) reduces particulates, chlorine, bad taste and odors. Service life: 6,000 gal. @ 3.0 GPM.
Double O-ring QD ball valve fittings
LVPO-F-2 (ice filter) reduces particulates and inhibits lime scale build-up. Service life depends on the water conditions.
Part Number
Description
WB2LVPO01
Water boost/filter combo system for fountain dispenser, single filter cartridge
WB2LVPO02
Water boost/filter combo system for fountain dispenser and ice machine, dual filter cartridges
9489700
SHURlock kit: 1/2" FPT quick connect swivel ball valve, (2) 3/8" barb x 1/2" MPT
9489700
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com Continuing product improvements may necessitate changes without notice. © 2010 ABS
E-11
WATER SYSTEMS
Selecto Water Booster Filter “Combo” Systems Selecto SMF filters remove 99% of all contaminants, don’t require a pre-filter for sediment removal, and provide high flow rates (up to 100 GPH/1.7 GPM) with nearly zero pressure drop. NSF std. 42 & 53. All SMF filters remove chloramine (chlorine + 20% ammonia used in many municipalities to slow the dissipation of chlorine). Chloramine has a strong odor, deteriorates O-rings, and causes stainless steel to pit, rust and turn gray.
Low draw systems have a 2 gallon tank, high draw systems have a 4 gallon tank. Filters with “-5” in the description have ScaleOUT (scale inhibitor) for ice machines. Operating pressure: 80-100 psi. Operating temperature: 40˚-100˚ F. Inlet and outlets: 3/8" barbs. Water analysis, site survey, selection of water appliances, service, maintenance and training are available.
QC350 Low Draw
QC500 Low Draw
QC500/ScaleOUT Low Draw
SMF IC600 Low Draw
SMF IC600-5 Low Draw
SMF IC614-5 Low Draw
SMF IC620 Low Draw
SMF IC620-5 Low Draw
SMF IC620-5 High Draw
Part Number Description
Chlorine Capacity
Chloramine Capacity
Scale Capacity
Tank Capacity
Replacement Cartridge(s)
660350
QC350 Low Draw
8,000 gals.
4,000 gals.
N/A
2 gals.
QC3502
660500
QC500 Low Draw
11,000 gals.
6,000 gals.
N/A
2 gals.
QC5002
660500S
QC500/ScaleOUT Low Draw
11,000 gals.
6,000 gals.
30,000 gals.
2 gals.
1090500S
660600LFM
SMF IC600 Low Draw
50,000 gals.
7,000 gals.
N/A
2 gals.
108010
666105LFM
SMF IC600-5 Low Draw
50,000 gals.
7,000 gals.
75,000 gals.
2 gals.
108015S
666145LFM
SMF IC614-5 Low Draw
70,000 gals.
15,000 gals.
75,000 gals.
2 gals.
108016S
660620LFM
SMF IC620 Low Draw
100,000 gals.
30,000 gals.
N/A
2 gals.
108020
660625LFM
SMF IC620-5 Low Draw
100,000 gals.
30,000 gals.
75,000 gals.
2 gals.
108025S
660625HFM
SMF IC620-5 High Draw
100,000 gals.
30,000 gals.
75,000 gals.
4 gals.
108025S
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com E-12
Continuing product improvements may necessitate changes without notice. © 2010 ABS
WATER SYSTEMS
3M™ Water Filtration Products for Multi-Equipment Applications The High Flow Series can meet the filtration needs of an entire foodservice establishment or address specific applications one at a time. A one-cartridge High Flow system with Integrated Membrane Pre-Activated Carbon Technology (“IMPACT”) media delivers recipe quality water of up to 5 gallons per minute, lasts 6 months, and accomplishes what was previously the job of a three- or four-cartridge system.
Carbon Technology (“IMPACT”) media provides nearly 6 times the filtration surface area, and reduction of up to 99.99% of common water-borne heterotrophic bacteria as tested by 3M Purification Inc., as well as Cryptosporidium and Giardia cysts. No activation steps are required, and for most water, no pre-filter is needed. Change-outs are fast and easy with the Sanitary Quick Change (SQC) encapsulated cartridge design. Most cartridge materials are NSF Std. 42 and/or CRF-21 compliant and certified by NSF to Std. 53 for cyst reduction.
The High Flow Series provides unprecedented cyst and bacteria reduction, sediment holding, chlorine taste and odor reduction and scale inhibition. Integrated Membrane Pre-Activated
Dual Port (DP) and Dual Flow (DF) Systems for Multiple Applications Two separate streams exit the manifold. Both streams have reduced sediment and chlorine taste and odor. One stream has added scale inhibition media from a dedicated cartridge to help reduce the ability of calcium and magnesium to adhere as hard scale on the evaporator plates of an ice machine and/or the heating coils of a coffee brewer. The second stream supplies cold beverage dispensers and includes no added scale inhibitor.
DP290
Model
Gallon Capacity
GPM Flow Rate
Micron Rating
Fountain/Cold Cup
Coffee/Tea/Hot Cup
Ice Machine
Case Qty.
Replacement Cartridge
DP390
Part Number
Espresso/Cappacino
DP190
DP190
5624301
54,000
5
.2
X
X
X
1
5613801
Cyst1, bacteria2, bacteriostatic, sediment3, chlorine taste & odor, scale3
DP290
5624201
108,000
10
.2
X
X
X
1
5613802
Cyst1, bacteria2, bacteriostatic, sediment3, chlorine taste & odor, scale3
DP390
5624102
162,000
15
.2
X
X
X
1
5613803
Cyst1, bacteria2, bacteriostatic, sediment3, chlorine taste & odor, scale3
DF290-CL*
5623601
25,000
2.7 /5
.2
X
X
1
5613807
Cyst1, bacteria2, bacteriostatic, sediment3, chloramine, chlorine taste & odor, scale3
Reduces
Contains Integrated Membrane Pre-Activated Carbon Technology (“IMPACT”) media for cyst and bacteria reduction. Tested by manufacturer. As tested with E. Coli ATCC (11229) by 3M Purification Inc. Not tested or certified by NSF International. 3 As tested and verified by Manufacturer’s Laboratory *Beverage flow rate is 2.66 GPM, ice machine flow rate is 5 GPM. 1 2
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com Continuing product improvements may necessitate changes without notice. © 2010 ABS
E-13
WATER SYSTEMS
3M™ Water Filtration Products for Cold Beverages Cold beverages are often the most profitable part of convenience stores, restaurants and quick-service operations. For these high-volume cold beverage applications, High Flow filters deliver enough Recipe Quality Water™ to make more than 432,000 soft drinks (16 oz. soft drinks in 22 oz. cups) with a single cartridge. High Flow catridge filters deliver the improved performance of Integrated Membrane Pre-Activated Carbon Technology (“IMPACT”) media. A single High Flow cartridge system replaces a three- or four-cartridge manifold system, lowering capital and operating costs.
All systems on this page deliver sediment and chlorine taste and odor reduction. BEV130 (std. 42 & 53) and BEV135 (std. 42) contain media wrapped carbon-block only. BEV140, BEV160 and BEV190 systems include Integrated Membrane Pre-Activated Carbon Technology (“IMPACT”) media for cyst and bacteria2 reduction, and are NSF std. 42 and 53. BEV135, BEV145, BEV165 and BEV195 systems are designed for high turbidity water, but not cyst or bacteria reduction, and are std. 42 only. All have NSF and/or FDA CFR-21 compliant materials.
Micron Rating
Fountain/Cold Cup
Case Qty.
BEV130
5616101
14,000
1.7
.5
X
4
5615105
Cyst1, sediment3, chlorine taste & odor
BEV135
5616102
12,600
1.7
1
X
4
5615205
Sediment3, chlorine taste & odor
BEV140
5616201
25,000
2.1
.2
X
2
5613303
Cyst1, bacteria2, bacteriostatic, sediment3, chlorine taste & odor
BEV145
5616202
25,000
2.1
3
X
2
5613307
Sediment3, chlorine taste & odor
BEV160
5616301
35,000
3.3
.2
X
1
5613403
Cyst1, bacteria2, bacteriostatic, sediment3, chlorine taste & odor
BEV165
5616302
35,000
3.3
3
X
1
5613407
Sediment3, chlorine taste & odor
BEV190
5616401
54,000
5
.2
X
1
5613503
Cyst1, bacteria2, bacteriostatic, sediment3, chlorine taste & odor
BEV195
5616402
54,000
5
3
X
1
5613507
Sediment3, chlorine taste & odor
Replacement Cartridge
Model
GPM Flow Rate
BEV190 BEV195
Gallon Capacity
BEV160 BEV165
Part Number
BEV130 BEV135
Reduces
Contains Integrated Membrane Pre-Activated Carbon Technology (“IMPACT”) media for cyst and bacteria reduction. Tested by manufacturer. As tested with E. Coli ATCC (11229) by 3M Purification Inc. Not tested or certified by NSF International. 3 As tested and verified by Manufacturer’s Laboratory 1 2
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com E-14
Continuing product improvements may necessitate changes without notice. © 2010 ABS
WATER SYSTEMS
3M™ Water Filtration Products for Ice Machines Scale build-up on evaporator plates can significantly increase maintenance costs. 3M Water Filtration Products for ice machines provide built-in scale inhibition as well as chlorine and sediment reduction, which reduce service calls and downtime, yield consistent product, and increase customer satisfaction.
HF Cubers Lbs. To
LF Cubers Lbs. To
Flakers Lbs. To
Case Qty.
ICE120-S
5616003
9,000
1.5
.5
200
750
1200
6
HF20S Cyst1, sediment3, chlorine taste & odor, scale3 5615103
ICE125-S
5616004
10,000
1.5
1
200
750
1200
6
HF25S Sediment3, chlorine taste & odor, scale3 5615203
ICE140-S
5616203
25,000
2.1
.2
600
1000
1800
2
HF40S Cyst1, bacteria2, bacteriostatic, sediment3, chlorine 5613305 taste & odor, scale3
ICE145-S
5616204
25,000
2.1
3
600
1000
1800
2
HF45S Sediment3, chlorine taste & odor, scale3 5613309
ICE160-S
5616303
35,000
3.3
.2
1000
1450
2400
1
HF60S Cyst1, bacteria2, bacteriostatic, sediment3, chlorine 5613405 taste & odor, scale3
ICE165-S
5616304
35,000
3.3
3
1000
1450
2400
1
HF65S Sediment3, chlorine taste & odor, scale3 5613409
ICE190-S
5616403
54,000
5
.2
>1000
>1450
>2400
1
HF90S Cyst1, bacteria2, bacteriostatic, sediment3, chlorine 5613505 taste & odor, scale3
ICE195-S
5616404
54,000
5
3
>1000
>1450
>2400
1
HF95S Sediment3, chlorine taste & odor, scale3 5613509
ICE260-S
5624503
70,000
6.7
.2
2400
3000
4800
1
(2) HF60S Cyst1, bacteria2, bacteriostatic, sediment3, chlorine 5613405 taste & odor, scale3
ICE265-S
5624504
70,000
6.7
3
2400
3000
4800
1
(2) HF65S Sediment3, chlorine taste & odor, scale3 5613409
Replacement Cartridges
Model
Micron Rating
ICE140-S
GPM Flow Rate
ICE120-S
Gallon Capacity
ICE190-S
Part Number
ICE265-S
ICE120-S (std. 42 & 53) and ICE125-S (std. 42) contain carbonblock media only. ICE140-S, ICE160-S, ICE190-S and ICE260-S include Integrated Membrane Pre-Activated Carbon Technology (“IMPACT”) media for cyst and bacteria2 reduction, and are NSF std. 42 and 53. For higher turbidity waters, the media in ICE145-S, ICE165-S, ICE195-S and ICE265-S systems are specifically designed to provide cartridge and system life, but not cyst or bacteria reduction, and are std. 42 only. All have NSF and/or FDA CFR-21 compliant materials.
Reduces
Contains Integrated Membrane Pre-Activated Carbon Technology (“IMPACT”) media for cyst and bacteria reduction. Tested by manufacturer. As tested with E. Coli ATCC (11229) by 3M Purification Inc. Not tested or certified by NSF International. 3 As tested and verified by Manufacturer’s Laboratory 1 2
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com Continuing product improvements may necessitate changes without notice. © 2010 ABS
E-15
WATER SYSTEMS
3M™ Water Filtration Products for Hot Beverages High Flow Series products for hot beverage applications reduce excess sediment and chlorine that cause bitter taste and clog spray heads. If not filtered, these elements can wreak havoc on your equipment and lead to expensive repair and replacement costs.
ESP 124
1,500
.75
1
X
8
BREW110-MS
6213803
3,500
1
.5
X
8
BREW115-MS
6213807
3,500
1
5
X
8
BREW120-MS
5616001
9,000
1.5
.5
X
6
BREW125-MS
5616002
10,000
1.5
1
X
6
BREW130-MS
5616103
14,000
1.7
.5
X
4
BREW135-MS
5616104
12,600
1.7
1
X
4
ESP114-T*
5617609
700 gr.
.5
N/A
X
6
HF05MS 5609327 HF10MS 5609329 HF15MS 5609331 HF20MS 5615109 HF25MS 5615209 HF30MS 5615111 HF35MS 5615211 5610909
ESP124-T*
5617610
1,100 gr.
.5
N/A
X
4
5610907
Hardness (softens), chlorine taste & odor
SGP124BN-T*
5617603
422.6
.5
N/A
X
4
5610901
Hard scale2, chlorine taste & odor
SGP165BN-T*
5617601
719
1
N/A
X
1
5615601
Hard scale2, chlorine taste & odor
SGP195BN-T*
5617602
1200
1
N/A
X
1
5615001
Hard scale2, chlorine taste & odor
SGP-124B*
5608902
422.6
.5
N/A
X
4
5609103
Hard scale2, chlorine taste & odor
X
Replacement Cartridge(s)
6213801
Case Qty.
Coffee/Hot Cup
BREW105-MS
Model
Part Number
Micron Rating
Espresso/Capp./Tea
SGP 165
GPM Flow Rate
BREW 130
ESP and ScaleGARD™ Pro (SGP) systems reduce calcium and magnesium ions by ion exchange (water softening) for crystal clear iced tea and excellent bean extraction for espresso and espresso-based beverages. ESP and SGP systems do not need a drain, electrical connection or salt regeneration. All have NSF and/or FDA CFR-21 compliant materials.
Gallon Capacity
BREW 120
When scale is an issue, High Flow BREW systems add scale inhibitor to prevent calcium and magnesium build-up that can significantly decrease efficiency and increase maintenance costs.
Reduces Sediment2, chlorine taste & odor, scale2 Cyst1, sediment2, chlorine taste & odor, scale2 Sediment2, chlorine taste & odor, scale2 Cyst1, sediment2, chlorine taste & odor, scale2 Sediment2, chlorine taste & odor, scale2 Cyst1, sediment2, chlorine taste & odor, scale2 Sediment2, chlorine taste & odor, scale2 Hardness (softens), chlorine taste & odor
Contains Integrated Membrane Pre-Activated Carbon Technology (“IMPACT”) media for cyst and bacteria reduction. Tested by manufacturer. As tested and verified by Manufacturer’s Laboratory *Systems not NSF listed 1 2
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com E-16
Continuing product improvements may necessitate changes without notice. © 2010 ABS
WATER SYSTEMS
NEW!
3M™ Water Filtration Products for Hot Beverages - Reverse Osmosis For optimum flavor it is recommended that filtered water contain 100-200 ppm of Total Dissolved Solids (TDS) for coffee and about 50 ppm for espresso.
Features: • Makes 300 gal/day without blending*, and up to 600 gal/ day of blended water • Blending valve (with lock) adjusts the desired amount of TDS, and online meter monitors product water TDS level • Keeps running during high demand periods and power outages with automatic non-electric bypass • All product water (including bypass) is pre- and postfiltered • Change-outs are fast and easy with Sanitary Quick Change (SQC) disposable cartridges • Compact, uses very little space, and is easy to install • Optional pumping module is available for low inlet water pressure areas
Designed for water conditions with high TDS and/or hardness, the TFS450 reverse osmosis (RO) water filtration system is ideal. RO is the tightest of all filtration processes, removing about 90% of all contaminants and providing the greatest equipment protection. The TFS450 has a blending feature that allows you to blend back just the right amount of TDS (from 10-50% of incoming feed water) into the water to satisfy both needs; equipment protection and customer satisfaction. With conventional RO systems the waste water can be 2-4 times the volume of the filtered water. For the production of 100 gallons of filtered water the TFS450 conserves up to 250 gallons of water per day - over 90,000 gallons per year - than conventional RO systems.
The TFS450 requires an external storage tank.
Espresso/Capp./Tea
Case Qty.
.0005
X
X
1
Replacement Cartridge(s)
Coffee/Hot Cup
5623901 300 gpd without blending/ 600 gpd with blending
Micron Rating
TFS450RO
Gallon Capacity
Model
Part Number
TFS450
5624802
Reduces Cysts1, sediment2, chlorine taste & odor, TDS
Contains Integrated Membrane Pre-Activated Carbon Technology (“IMPACT”) media for cyst and bacteria reduction. Tested by manufacturer. As tested and verified by Manufacturer’s Laboratory *at 77˚ F and 70 psi. 1 2
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com Continuing product improvements may necessitate changes without notice. © 2010 ABS
E-17
WATER SYSTEMS
5609327 5609329 5609331 5610901 5610907 5610909 5613303 5613305 5613307 5613309 5613403 5613405 5613407 5613409 5613503 5613505 5613507 5613509 5613801 5613802 5613803 5613807 5615001 5615103 5615105 5615109 5615111 5615203
Model HF05-MS 1,500 .75 1 HF10-MS 3,500 1 .5 HF15-MS 3,500 1 5 P124BN* 423@ 10 gr. .5 N/A PS124* 1,100 gr. .5 N/A PS114* 700 gr. .5 N/A HF40 25,000 2.1 .5 HF40-S 25,000 2.1 .2 HF45 25,000 2.1 1 HF45-S 25,000 2.1 3 HF60 35,000 3.3 .2 (2) HF60-S 70,000 6.7 .2 HF65 35,000 3.3 3 (2) HF65-S 70,000 6.7 3 HF90 54,000 5 .2 HF90-S 54,000 5 .2 HF95 54,000 5 3 HF95-S 54,000 5 3 DP190-CARTPAK 54,000 5 .2 DP290-CARTPAK 108,000 10 .2 DP390-CARTPAK 162,000 15 .2 DF290CL-CART25,000 2.7/5 .2 PAK P195BN* 1200@ 9 gr. 1 N/A HF20-S 9,000 1.5 .5 HF30 14,000 1.7 .5 HF20-MS 9,000 1.5 .5 HF30-MS 14,000 1.7 .5 HF25-S 10,000 1.5 1
Case Qty.
Micron Rating
GPM Flow Rate
Part Number
Gallon Capacity
3M™ Replacement Cartridges for 3M™ Water Filtration Systems
Sorted by Part Number
8 8 8 4 4 6 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1
Reduces Sediment3, chlorine taste and odor, scale3 Cyst1, sediment3, chlorine taste and odor, scale3 Sediment3, chlorine taste and odor, scale3 Hardness, chlorine taste and odor Hardness, chlorine taste and odor Hardness (softens), chlorine taste and odor Cyst1, bacteria2, sediment3, chlorine taste and odor Cyst1, bacteria2, sediment3, chlorine taste and odor, scale3 Sediment3, chlorine taste and odor Sediment3, chlorine taste and odor, scale3 Cyst1, bacteria2, sediment3, chlorine taste and odor Cyst1, bacteria2, sediment3, chlorine taste and odor, scale3 Sediment3, chlorine taste and odor Sediment3, chlorine, taste and odor, scale3 Cyst1, bacteria2, sediment3, chlorine taste and odor Cyst1, bacteria2, sediment3, chlorine taste and odor, scale3 Sediment3, chlorine taste and odor Sediment3, chlorine taste and odor, scale Cyst1, bacteria2, sediment3, chlorine taste and odor, scale3 Cyst1, bacteria2, sediment3, chlorine taste and odor, scale3 Cyst1, bacteria2, sediment3, chlorine taste and odor, scale3 Cyst1, bacteria2, sediment3, chloramine, chlorine taste and odor, scale3
1 6 4 6 4 6
Hardness, chlorine taste and odor Cyst1, sediment3, chlorine taste and odor, scale3 Cyst1, sediment3, chlorine taste and odor Cyst1, sediment3, chlorine taste and odor, scale3 Cyst1, sediment3, chlorine taste and odor, scale3 Sediment3, chlorine taste and odor, scale3
Contains Integrated Membrane Pre-Activated Carbon Technology (“IMPACT”) media for cyst and bacteria reduction. Tested by manufacturer. As tested with E. Coli ATCC (11229) by 3M Purification Inc. Not tested or certified by NSF International. 3 As tested and verified by Manufacturer’s Laboratory *Systems not NSF listed 1 2
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com E-18
Continuing product improvements may necessitate changes without notice. © 2010 ABS
WATER SYSTEMS
HF35 HF25-MS HF35-MS P165BN* CFS9110 CFS9112 CFS9812X CFS9720 CFS9110S CFS9112S CFS9812XS CFS9710S CFS9720S CFS9005IMF CFS9112EL CFS9812ELX CFS9720EL CFS9112ELS CFS9812ELXS CFS9720ELS SWC9135 SWC9135C
12,600 10,000 12,600 719@ 9 gpg N/A 10,000 9,000 4,800 N/A 10,000 9,000 2,400 4,800 N/A 12,600 14,000 5,500 12,600 14,000 5,500 1,350 gr. 1,100 gr.
Case Qty.
5615205 5615209 5615211 5615601 5572101 5589203 5601201 5589003 5572103 5589201 5601203 5589101 5589001 5593701 5589213 5601205 5589005 5589215 5601207 5589007 5572201* 5572203*
Micron Rating
Model
GPM Flow Rate
Part Number
Gallon Capacity
3M™ Replacement Cartridges for 3M™ Water Filtration Systems
Sorted by Part Number
Reduces
1.7 1 4 Sediment3, chlorine taste and odor 1.5 1 6 Sediment3, chlorine taste and odor, scale3 1.7 1 4 Sediment3, chlorine taste and odor, scale3 1 N/A 1 Hardness, chlorine taste and odor 1.5 5 4 Sediment3 1.5 1 12 Sediment3, chlorine taste and odor 1.5 .5 12 Cyst1, sediment3, chlorine taste and odor 1.5 5 12 Sediment3, chlorine taste and odor 1.5 5 4 Sediment3, scale3 1.5 1 12 Sediment3, chlorine taste and odor, scale3 1.5 .5 12 Cyst1, sediment3, chlorine taste and odor, scale3 1 5 12 Sediment3, scale3 1.5 5 12 Sediment3, chlorine taste and odor, scale3 N/A N/A 12 Scale3 1.67 1 4 Sediment3, chlorine taste and odor 1.67 .5 4 Cyst1, sediment3, chlorine taste and odor 1.67 5 4 Sediment3, chlorine taste and odor 1.67 1 4 Sediment3, chlorine taste and odor, scale3 1.67 .5 4 Cyst1, sediment3, chlorine taste and odor, scale3 1.67 5 4 Sediment3, chlorine taste and odor, scale3 .5 N/A 4 Scale3 (softens water) .5 5 4 Chlorine taste and odor, scale3 (softens water)
Contains Integrated Membrane Pre-Activated Carbon Technology (“IMPACT”) media for cyst and bacteria reduction. Tested by manufacturer. As tested with E. Coli ATCC (11229) by 3M Purification Inc. Not tested or certified by NSF International. 3 As tested and verified by Manufacturer’s Laboratory *Systems not NSF listed 1 2
3M™ Replacement Filters
NEW!
NEW 9000 Series cartridges fit all Everpure heads, both old and new style.
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com Continuing product improvements may necessitate changes without notice. © 2010 ABS
E-19
WATER SYSTEMS
Selecto Water Filtration Systems Selecto’s SMF filters last up to 10 times longer than traditional carbon filters. Modular units are simple to install and service, and adaptable to changing water conditions change. All systems (except some inline filters) come with mounting brackets. Fountain systems have a pressure gauge. 100% performance guarantee. NSF 42 & 53.
Selecto’s hollow carbon filter Traditional carbon block filter
Selecto can customize a filtration system to meet your requirements. Call customer service for details.
IL35
QC350
QC500
SMF IC600
SMF IC614
SMF IC620
SMF IC620S
SMF IC6142
SMF IC6202
SMF IC6203
SMF Espresso 7500
SMF Espresso 12000
SMF CoffeePRO
SMF IC600S
ScaleOUT-W
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com E-20
Continuing product improvements may necessitate changes without notice. © 2010 ABS
WATER SYSTEMS
Espresso/Capp.
0110/35
Chlorine, sediment, bad taste, odor
1
X
X
X
0199/35B
Chlorine, sediment, bad taste, odor
3,000
2
X
X
X
0110/35S
Chlorine, sediment, bad taste, odor, scale
0110/35BS
2,500
1
X
X
X
0199/35BS
Chlorine, sediment, bad taste, odor, scale
QC350
QC3503
8,000
2.2
X
X
X
X
QC3502
Chlorine, chloramine, sediment, bad taste, odor
QC350S
QC350S
8,000
2.2
X
X
X
X
QC3502S
Chlorine, chloramine, sediment, bad taste, odor, scale
QC350F
QC350F
8,000
2.2
QC350-2
Chlorine, chloramine, sediment, bad taste, odor, scale
QC500
QC5003
11,000
2.5
X
X
X
X
QC5002
Chlorine, chloramine, sediment, bad taste, odor
QC500S
QC500S
11,000
2.5
X
X
X
X
QC5002S
Chlorine, chloramine, sediment, bad taste, odor, scale
QC500F
QC500F
11,000
2.5
X
QC500-2
Chlorine, chloramine, sediment, bad taste, odor, scale
QC500 Combo 60-0500S
11,000
2.5
X
1090500S
Chlorine, chloramine, sediment, bad taste, odor, scale
SMF Espresso 7500
821600
7,500
1
X
X
X
108600
Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale
SMF Espresso 12000
821620
12,000
2
X
X
X
108620
Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale
SMF CoffeePRO
806100CP
15,000
5
X
X
X
108010CP
Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale
ScaleOUT
05260W
40,000
5
X
X
X
X
101260
Scale
SMF IC600
806100
50,000
2.5
X
X
X
X
X
108010
Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor
SMF IC614
806140
70,000
3.7
X
X
X
X
X
108014
Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor
SMF IC620
806200
100,000
5
X
X
X
X
X
108020
Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor
SMF IC600S
801600S
50,000
5
X
X
X
X
X
X
108015S
Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale
SMF IC620S
806200S
100,000
5
X
X
X
X
X
X
108020S
Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale
SMF IC6142
806142
140,000
7.4
X
X
X
X
X
X
1080142
Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale
SMF IC6202
80-6202
200,000
10
X
X
X
X
X
1080202
Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor
SMF IC6203
806203
300,000
15
X
X
X
X
X
1080203
Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor
3,000
2
IL35B
0110/35B
3,000
IL35S
0110/35S
IL35BS
X
X
Replacement Cartridge(s)
Tea*
X
0110/35
Ice Machine
Coffee
X
IL35
Fountain
X
Part Number
GPM Flow Rate
X
Model
Gallon Capacity
Juice
Selecto Water Filtration Systems
Reduces/Eliminates
*Part numbers ending in “S” provide scale inhibition, which in some water conditions may cause tea to become cloudy. Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com Continuing product improvements may necessitate changes without notice. © 2010 ABS
E-21
WATER SYSTEMS
Selecto Water Filtration Systems
SlimeGUARD Spray
SlimeGUARD Stick
Part Number
SMF IcePRO
806100IP
15,000
5
X
108010IP
Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale
SMF IM600
806100S
75,000
7
X
108010S
Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale
SMF IM614
80614S
150,000
7
X
108014S
Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale
SlimeGUARD Spary
40003
N/A
N/A
X
N/A
Bacteria, mold, algae and fungus up to 3 months, ice makers up to 2400 lbs.
SlimeGUARD Stick
40002
N/A
N/A
X
N/A
Bacteria, mold, algae and fungus up to 3 months, ice makers up to 2400 lbs.
Replacement Cartridge(s)
Model
Ice Machine
SMF IM614
GPM Flow Rate
SMF IM600
Gallon Capacity
SMF IcePRO
Reduces/Eliminates
SHURflo Inline Filters Part Number
GPM
Port Fitting
Reduces/Eliminates
SF210TO
2
1/4" plastic FPT
taste, odor
SF210TOS
2
1/4" plastic FPT
taste, odor, sediment
SF210SED
2
1/4" plastic FPT
sediment
SF210TOHQD
2
1/4" brass quick disconnect
taste, odor
SF210TOSHQD
2
1/4" brass quick disconnect
taste, odor, sediment
SF210SEDHQD
2
1/4" brass quick disconnect
sediment
SF210TOPQD
2
1/4" plastic quick disconnect
taste, odor
SF210TOSPQD
2
1/4" plastic quick disconnect
taste, odor, sediment
SF210SEDPQD
2
1/4" plastic quick disconnect
sediment
SF215TOCAT
2.5
1/4" plastic FPT
SF215CATPQD
2.5
1/4" plastic quick disconnect
Female plastic quick disconnects can be found in the Installation Products, fittings section.
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com E-22
Continuing product improvements may necessitate changes without notice. © 2010 ABS
WATER SYSTEMS
SHURflo Water Filtration Systems Part Number
Single Standard 10" Filter System, 3/8" MPT threads
SF410010
With ball valve & gauge, no filters
SF410020
No fittings, no filters, single packed
SF410021
No fittings, no filters, bulk packed (12 to case)
SF412010
With ball valve & gauge, Granular Activated Carbon (GAC) element
SF414010
With ball valve & gauge, Granular Activated Carbon (GAC) / Phosphate Element
Single Standard 10"
Dual Standard 10" Filter Systems, 3/8" MPT threads SF510010
With ball valve & gauge, no filters
SF510020
No fittings, no filters
SF511110
With ball valve & gauge, 5 micron sediment/GAC element
SF511310
With ball valve & gauge, 5 micron sediment/GAC/phosphate element
SF414010
With ball valve & gauge, Granular Activated Carbon (GAC) / Phosphate Element
Dual Standard 10"
Dual Standard 10" UV Filter Systems, 3/8" MPT threads SF520010
US System with ball valve & gauge, mechanical ballast, no filters
SF520020
US System, no fittings, mechanical ballast, no filters
SF521110
US System with ball valve & gauge, mech. ballast, 5 mic sed/GAC element
Dual Standard 10" UV
Dual Great White 10" x 20" Filter Systems, 3/4" MPT threads SF60010
With ball valve & gauge, no filters
SF60020
No fittings, no filters
SF600TOCL
With ball valve & gauge, 5 micron sediment/GAC element
Dual Great White 10" Filter Systems, 3/4" MPT threads SF50010
With ball valve & gauge, no filters
SF50020
No fittings, no filters
SF500TOCL
With ball valve & gauge, 5 micron sediment/GAC element
SF530010
US System with ball valve & gauge, mechanical ballast, no filters
SF530020
US System, no fittings, mechanical ballast, no filters
Dual Great White 10" & 20"
Dual Great White 10" UV Filter Systems, 3/4" MPT threads Dual Great White 10"
Dual Great White 20" Filter Systems, 3/4" MPT threads SF70010
With ball valve & gauge, no filters
SF70020
No fittings, no filters
Accessory Description 1505610
UV light, 2.0 GPM, 8 watts, 2 pin
1505611
UV light, 1.0 GPM, 6 watts, 2 pin
1505700
UV light ballast, 2 pin
1505800
Clip set (2) for UV light and inline filters
1504800
Wrench for standard series sumps
1504700
Wrench for Great White Series 10" sumps
1504900
Wrench for Great White Series 20" sumps
UV light 1505700
1505800 Wrenches
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com Continuing product improvements may necessitate changes without notice. © 2010 ABS
E-23
WATER SYSTEMS
SHURflo Replacement Filters Part Number
Standard 10" Replacement Filters
1502812
Standard 10" 0.5 micron modified molded carbon block FD
1505200
Standard 10" 5 micron spun bonded polypropylene sediment cartridge
1505300
Standard 10" 20 micron water washed coconut shell granular activated carbon (GAC) element
1505400
Standard 10" 5 micron GAC w food grade hexametaphosphate
1505420
Standard 10" phosphate crystal cartridge
1505430
Standard 10" cation softening resin
1505500
Standard 10" 20 micron spun bonded polypropylene sediment cartridge
1505620
Standard 10" 4-8 micron modified molded block FD
1505610
Standard 10" 4-8 micron modified molded block FD with siliphos softening
1505203
Standard 20" 5 micron spun bonded polypropylene sediment cartridge
1505503
Standard 20" 20 micron spun bonded polypropylene sediment cartridge
1506200
Standard 20" 10 micron modified molded carbon block
1505300
Standard 20" 0.5 micron modified molded carbon block
1503900
Great White 10" 5 micron modified carbon block - FD
1503910
Great White 10" 5 micron modified carbon block - FD with siliphos
1504000
Great White 10" 0.5 micron carbon briquette
1505201
Great White 10" 1 micron nom dual gradient density SED element - spun poly
1505301
Great White 10" 5 micron granular activated carbon/SED element
1505401
Great White 10" 5 micron SED element - pleated polypropylene
1504100
Great White 20" 0.5 micron carbon briquette
1505202
Great White 20" 1 micron nom dual gradient density SED element - spun poly
1505302
Great White 20" 5 micron granular activated carbon/SED element
1505402
Great White 20" 5 micron SED element pleated polypropylene
9475100
LVPO-F1 starter kit: 5 micron carbon filter NSF 42, SHURlock 3/8" barb ball balve, filter brackets, QD-bypass
9447900
LVPO-F2 starter kit: 5 micron sediment & phosphate filter NSF 42, SHURlock 3/8" barb ball balve, filter brackets, QD-bypass
9475101
LVPO-F3 starter kit: 5 micron carbon & phosphate filter NSF 42, SHURlock 3/8" barb ball balve, filter brackets, QD-bypass
LVPO-F1
9475102
LVPO-F4 starter kit: inline resin filter, SHURlock 3/8" barb ball balve, filter brackets, QD-bypass
LVPO-F2
9439900
LVPO-F1, 5 micron carbon filter NSF 42, 3 GPM, 6000 gal life
9447000
LVPO-F2, 5 micron sediment & phosphate filter NSF 42, 3 GPM, life depends on water conditions
9447001
LVPO-F3, 5 micron carbon & phosphate filter NSF 42, 3 GPM, 6000 gal life
9447002
LVPO-F4, inline resin filter, .5 GPM, 4400 grains or 500 gal @ 150 ppm
9472900
PLF-1 inline 5 micron carbon filter NSF 42, 2 GPM, 5000 gal life
1505620
1503900
LVPO starter kit
LVPO-F3 LVPO-F4
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com E-24
Continuing product improvements may necessitate changes without notice. © 2010 ABS
WATER SYSTEMS
SHURflo Accessories and Fittings Part Number
Description
9447500
LVPO filter QD-bypass
9447300
LVPO filter brackets for slide track/wall mount, 1 pair
9447400
LVPO filter to filter brackets, 1 pair
9447200
LVPO filter brackets for tank mount, 1 pair
9447100
Quick connect 3/8" barb ball valve set: gray handle for inlet, blue handle for outlet
9447101
Quick connect 1/2" FPT with SS rings ball 90˚ valve set: gray handle for inlet, blue handle for outlet
183130SS
30 psi water pressure reducer valve, 3/8" SS barb inlet/outlet
183150SS
50 psi water pressure reducer valve, 3/8" SS barb inlet/outlet
183165SS
65 psi water pressure reducer valve, 3/8" SS barb inlet/outlet
183180SS
80 psi water pressure reducer valve, 3/8" SS barb inlet/outlet
9416500
65 psi water pressure reducer valve w pressure gauge, 3/8" barb inlet/outlet
17006029
Water strainer, 50 mesh SS screen, EPDM O-ring, 1/2" barb inlet, 1/2" FPST outlet.*
17006104
Water strainer, 50 mesh SS screen, Buna O-ring, 1/2" barb inlet, 1/2" FPST outlet.*
17006105
Water strainer, 50 mesh SS screen, Viton® O-ring 1/2" barb inlet, 1/2" FPST outlet.*
17006109
Water strainer, 50 mesh SS screen, EPDM O-ring 1/2" barb inlet, 1/2" FPST outlet.*
8433134
Tank pressure switch, 25 psi on/40 psi off, NPT ports
9409000
Tank pressure switch, 25 psi on/40 psi off, FPT ports, 2' wire harness
9409001
Tank pressure switch, 25 psi on/40 psi off, push fit connectors, 2' wire harness
9409002
Tank pressure switch, 25 psi on/40 psi off, 3/8" push fit connectors, 2' wire harness
8433137
Low pressure switch, 3 psi on / 8 psi off, FPT ports
9408001
Low pressure switch, 3 psi on / 8 psi off, push fit connectors, 2' wire harness
800700
3/8" MPT x 1/2" straight barb, electric pump fitting, plastic
800500
3/8" MPT x 3/8" straight barb, electric pump fitting, plastic
800800
3/8" MPT x 1/2" elbow barb, electric pump fitting, plastic
800600
3/8" MPT x 3/8" elbow barb, electric pump fitting, plastic
807000
1/2" swivel nut x 1/2" straight barb, electric pump fitting, plastic
807100
1/2" swivel nut x 3/8" straight barb, electric pump fitting, plastic
807200
1/2" swivel nut x 1/4" straight barb, electric pump fitting, plastic
803400
1/2" swivel nut x 1/2" elbow barb, electric pump fitting, plastic
806000
1/2" swivel nut x 3/8" elbow barb, electric pump fitting, plastic
806900
1/2" swivel nut x 1/4" elbow barb, electric pump fitting, plastic
814500
3/8" MPT x 1/2" MPT adapter, electric pump fitting, plastic
Quick connect 90˚ valve set
Water pressure reducer valve
Water strainers
Tank pressure switch
*Use adapter 814501 for 8000 Series pumps with 3/8" FPT
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com Continuing product improvements may necessitate changes without notice. © 2010 ABS
E-25
WATER SYSTEMS
SHURflo Accessories and Fittings Part Number 807001 807101 815401 815601 816101 815501 815801 815901 815701 803400 806000 803500 820500 815001 826901 812600
Description Hex swivel straight, polypropylene 1/2" FPT x 1/2" barb Hex swivel straight, polypropylene 1/2" FPT x 3/8" barb Wingnut swivel straight, polypropylene 1/2" FPT x 5/8" barb Wingnut swivel straight, polypropylene 1/2" FPT x 3/4" barb Wingnut swivel straight, polypropylene 1/2" FPT x 1/2" barb Wingnut swivel elbow, polypropylene, 1/2" FPT x 5/8" barb Wingnut swivel elbow, polypropylene, 1/2" FPT x 1/2" barb Wingnut swivel elbow, polypropylene, 1/2" FPT x 3/8" barb Wingnut swivel elbow, polypropylene, 1/2" FPT x 3/4" barb Hex swivel elbow, polypropylene, 1/2" FPT x 1/2" barb Hex swivel elbow, polypropylene, 1/2" FPT x 3/8" barb Hex swivel elbow, polypropylene, 1/2" FPT x 1/2" MPT Adapter, nylon 1/2" FPT x 1/2" MPT Adapter, Nylon 1/2" FPT x 3/4" GSH (M) Adapter, Nylon 1/2" MPT x 3/4" barb Barb tee, polypropylene, 1/2" barb x 1/2" barb x 1/2" barb
Hex swivel straight
Wingnut swivel straight
Wingnut swivel elbow
Hex swivel elbow
Adapter, FPT x MPT
Adapter, FPT x GSH (M)
Adapter, MPT x barb
Barb tee
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com E-26
Continuing product improvements may necessitate changes without notice. © 2010 ABS
WATER SYSTEMS
Everpure Water Filtration Systems Everpure products can help you enjoy the taste without the waste of bottled water, and indirectly reduce waste by saving energy and prolonging the life of your equipment.
Everpure has over 200 models and model variations, and can customize a system to meet your needs. The most popular systems are shown here.
Water analysis, site survey, selection of water appliances, service, maintenance and training are available.
All systems have a five year warranty, and cartridges have a one year limited warranty. NSF std. 42 & 53.
QC71 Twin-MC
QC71 Single-MC
Coldrink 3-MC
Insurice Twin I2000
QC71 Triple-MC
Dual HF Coldrink S-MC
Insurice Triple I4000
QC71 Quad-MC
CB20-124E
Insurice Quad I4000
CB20-302E
Coldrink 1-MC
Coldrink 2-MC
CB20-312E Insurice Single I2000
E-Series 10" Prefilter E-Series 20" Prefilter SRX Scale Inhibitor Feeder
IN-6 Inline Filter Head and filter sold separately
IN-10 Inline Filter
IN-12 Inline Filter
EV933726 SRX
QL2-OW200L
QL2-OCS
QL3-BH
QC7I Single-MH
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com Continuing product improvements may necessitate changes without notice. © 2010 ABS
E-27
WATER SYSTEMS
Everpure Water Filtration Systems
Replacement Cartridge(s)/Kits
QC71 Twin-MH2
EV927222
18,000
1
QC71 Single-ESO7 QC71 Twin-ESO7 QC71 Triple-ESO7 Coldrink 1 MC2
EV927241 EV927222 EV927223 EV932801
5,300 gr. 10,600 gr. 15,900 gr. 9,000
.5 1 1.5 1.7
X
Coldrink 2 MC2
EV932802
18,000
3.3
X
Coldrink 3 MC2
EV932803
27,000
5
X
Dual High Flow Coldrink S-MC2 Dual High Flow Coldrink M-XC2 CB20-124E CB20-302E CB20-312E
EV933744
72,000
13.4
X
EV933722
96,000
13.4
X
EV910051 EV910032 EV910037
15,000 20,000 60,000
5 5 5
X X X
Insurice Single I20002
EV932401
9,000
1.7
X
(1) EV961222 Sediment, chlorine, taste, odor, cyst, scale
Insurice Twin I20002 Insurice Triple I40002 Insurice Quad I40002 Insurice Single PFI20002
EV932402 EV932503 EV932504 EV932421
18,000 36,000 48,000 9,000
3.3 5 6.7 1.7
X X X X
(2) EV961222 (3) EV931232 (4) EV931232 (1) EV953426 (1) EV961222
Sediment, chlorine, taste, odor, cyst, scale Sediment, chlorine, taste, odor, cyst, scale Sediment, chlorine, taste, odor, cyst, scale Sediment, chlorine, taste, odor, cyst, scale, anitmicrobial protection
Insurice Twin PFI20002
EV932422
18,000
3.3
X
Insurice Triple PFI40002 EV932523
36,000
5
X
SRX Scale Inhibitor
EV979845
Depends
N/A
(1) EV953426 (2) EV961222 (1) EV953426 (3) EV961232 (1) EV979902
Sediment, chlorine, taste, odor, cyst, scale, anitmicrobial protection Sediment, chlorine, taste, odor, cyst, scale, anitmicrobial protection Scale, deliming
E-Series 10" Prefilter
EV979580
Depends
N/A
X
X
X
X
X
X
(1) EV953412 Sediment
E-Series 20" Prefilter
EV979590
Depends
N/A
X
X
X
X
X
X
(1) EV953412 Sediment
X X X X
Combination
1.7 3.3 5 6.7 1
Drinking Water
9,000 18,000 27,000 36,000 9,000
Ice Machine
EV927501 EV927502 EV927503 EV933711 EV927241
Coffee
GPM Flow Rate
QC71 Single-MC2 QC71 Twin-MC2 QC71 Triple-MC2 QC71 Quad-MC2 QC71 Single-MH2
Fountain
Model
Part Number
Gallon Capacity
Espresso/Capp.
Did you know as little as a 1/8" layer of scale can reduce the efficiency of a coffee machine by 50%, resulting in twice the amount of electricity consumed?
X X X X X
(1) EV961256 (2) EV961256 (1) EV997042 (1) EV962828 (1) EV961301
X
(2) EV961321 X X X
X X X X
X X X
X
X X X
X X X
X
(1) EV960725 (2) EV960725 (3) EV960725 (1) EV953426 (1) EV961256 (1) EV953426 (2) EV961256 (1) EV953426 (3) EV961256 (2) EV953426 (8) EV961256 (2) EV953426 (8) EV961256 (1) EV910502 (1) EV910521 (1) EV910534
Reduces/Eliminates Sediment, taste, odor, cyst Sediment, taste, odor, cyst Sediment, taste, odor, cyst Sediment, taste, odor, cyst Sediment, chlorine, taste, odor, cyst, scale (head only, filter sold separately) Sediment, chlorine, taste, odor, cyst, scale (head only, filter sold separately) Hardness Hardness Hardness Sediment, taste, odor, cyst Sediment, taste, odor, cyst Sediment, taste, odor, cyst Sediment, taste, odor, cyst Sediment, taste, odor, cyst Chloramine, chlorine, taste, odor, cyst Chloramine, chlorine, taste, odor, cyst Chloramine, chlorine, taste, odor, cyst
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com E-28
Continuing product improvements may necessitate changes without notice. © 2010 ABS
WATER SYSTEMS
Everpure Water Filtration Systems
EV934720
EV932805
SO-24 Espresso SO-20 Housing SO-10 Housing High Flow CSR Twin-MC2
EV910094 EV910003 EV910002 EV933042
4,500 1,500 750 18,000
2 .75 .5 3.3
X X X X
X
X
X
X
High Flow CSR Triple-MC2 *optional low pressure alarm High Flow CSR QuadMC2 *optional low pressure alarm High Flow CSR Plus-XC2 (with 5 gallon reserve surge tank) HSD 440P Automatic Self Flushing Prefilter (120V) QL2-OW200L
EV932806, *with alarm: EV932805 EV943710, *with alarm: EV943711 EV944720, *with alarm: EV934721 EV934400
27,000
5
X
X
X
X
X
36,000
6.7
X
X
X
X
X
48,000 6.7
X
X
X
X
X
X
X
X
X
X
Combination
X
Drinking Water
1.7
Ice Machine
9,000
Esp./Capp./Tea
EV927224
Coffee
MC2-SO
Fountain
Model
Part Number
X
EV934400
EV934430
GPM Flow Rate
EV910002
Gallon Capacity
EV910094
EV933042
Replacement Cartridge(s)
EV910003
EV927224 Head and filters sold separately
(1) EV961256 (1) EV960704 (1) DEV910545 (1) DEV910542 (1) DEV910541 (1) EV953426 (2) EV961256 (1) EV979932 (1) EV953426 (3) EV961256 (1) EV979932 (1) EV953426 (4) EV961256 (1) EV979932 (1) EV953426 (4) EV961310 (1) EV979932 (1) EV312536
Reduces/Eliminates Sediment, taste, odor, cyst, and softens 2,000 grains Hardness (softens 4,500 grains) Hardness (softens 1,500 grains) Hardness (softens 750 grains) Sediment, taste, odor, cyst, scale
Sediment, taste, odor, cyst, scale
Sediment, taste, odor, cyst, scale
Sediment, taste, odor, cyst, scale
N/A
10
EV927570
480
.5
QL2-OCS2
EV927560
1,500
.5
X
(1) EV961801
Sediment, turbidity, bacteria, virus (.025 micron) Sediment, chlorine, taste, odor, lead, THMs, asbestos, cyst, scale Sediment, chlorine, taste, odor, cyst, scale
QL3-BH2
EV927200
3,000
.5
X
(1) EV961200
Sediment, chlorine, taste, odor, cyst, scale
X
(1) EV961901
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com Continuing product improvements may necessitate changes without notice. © 2010 ABS
E-29
WATER SYSTEMS
Everpure Claris Water Filtration Systems for Coffee, Espresso and Brewed Iced Tea To achieve the Golden Cup Standards of the Specialty Coffee Association of America, it is recommended that filtered water contain 100-200 ppm of Total Dissolved Solids (TDS) for coffee and ~50 ppm for espresso for optimum flavor.
The CLARIS Flow Sensor monitors the filtrate volume to calculate and display the remaining filtration capacity in litres. When the filtration capacity or the maximum operation time has been reached the display unit indicates filter cartridge replacement. The programming and display unit shows: • Residual capacity of installed filter cartridge • Filtrate volume of the last five installed filter cartridges • Operation time of the last five installed filter cartridges • Total filtrate volume since Flow Sensor installation
Claris’ adjustable ion-selective filters enable you to tailor the carbonate hardness levels to deliver just the right amount of TDS for optimum coffee and espresso flavor while removing excessive and harmful hard water contaminants. Claris can be installed vertically or horizontally. The head features a built-in flush port, auto shut-off, adjustable by-pass, flow restrictor and backflow restrictor. The duo-blend by-pass technology has a 5-stage filtration process: • Pre-filtration • Carbonate hardness adjustment • Fine filtration • Highly efficient carbon block removes harmful contaminants and unpleasant odors and tastes • Solid membrane filter removes particles down to 5 microns for equipment protection Heads and filters are sold separately.
Filter
Part Number
Gallon Capacity
GPM Flow Rate
Micron Rating
Coffee
Esp./Capp./Tea
Case Qty.
Claris Filter Family
Claris Small
EV433910
400
.5
5
X
X
1
Hardness, sediment, chlorine, taste, odor, scale
Claris Medium
EV433911
660
.5
5
X
X
1
Hardness, sediment, chlorine, taste, odor, scale
Claris Large
EV433912
1100
1
5
X
X
1
Hardness, sediment, chlorine, taste, odor, scale
Claris X-Large
EV433913
1585
1
5
X
X
1
Hardness, sediment, chlorine, taste, odor, scale
Part Number
Description
EV433921
Claris Head 3/8" BSP
EV433923
Claris Head 3/8" QCF
EV433925
Claris Head 1/4" QCF
EV433931
Claris Flowmeter
EV433940
Claris Test Kit
Claris Head
Reduces/Eliminates
Claris Flowmeter EV433931
Claris Test Kit
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com E-30
Continuing product improvements may necessitate changes without notice. © 2010 ABS
WATER SYSTEMS
Everpure Costguard Water Filtration Systems
DEV910012
CGS-10 Single CGS-12 Dual CGS-20 Single CGS-22 Dual CGS-23 Parallel CGS-55 Single
DEV910010 DEV910012 DEV910020 DEV910022 DEV910023 DEV910050
DEV910022
Filter Size Connection 10" 10" 20" 20" 20" 20"
3/8" FPT 1/2" FPT 3/8" FPT 1/2" FPT 3/8" FPT 1/2" FPT
DEV910023
Costguard value priced filtration systems are designed for rigorous applications. Housings feature inlet/outlet shut-off valves, gauges, mounting bracket and hardware. Costguard filters are standard width and length that will fit most sump style filtration systems. Housing and filters are sold separately.
Everpure Costguard Filters
20 20 20 20 5 5 5 5 .5 .5 .5 .5
X X
X X
X X
X X
X X
X X
X X
X X
X X
Drinking Water
1 2 1 2 1.7 3.3 1.7 3.3 2 4 2 4
Ice Machine
5,000 10,000 5,000 10,000 6,000 12,000 6,000 12,000 10,000 20,000 10,000 20,000
Esp./Capp./Tea
Micron Rating
DEV910813 DEV910833 DEV910811 DEV910832 DEV910817 DEV910827 DEV910815 DEV910825 DEV910857 DEV910867 DEV910853 DEV910863
Coffee
GPM Flow Rate
CGT10S CGT20S CGT10 CGT20 CG510S CG520S CG510 CG520 CG5310S CG5320S CG5310 CG5320
Fountain
Part Number
Gallon Capacity
DEV910811
Filter
DEV910050
DEV910815
DEV910857
Case Qty.
Housing
Part Number
DEV910020
Combination
DEV910010
Reduces/Eliminates
12 6 12 6 12 6 12 6 12 6 12 6
Clorine, taste, odor, scale Clorine, taste, odor, scale Clorine, taste, odor Clorine, taste, odor Clorine, taste, odor, scale, sediment Clorine, taste, odor, scale, sediment Clorine, taste, odor, sediment Clorine, taste, odor, sediment Clorine, taste, odor, scale, sediment, cyst Clorine, taste, odor, scale, sediment, cyst Clorine, taste, odor, sediment, cyst Clorine, taste, odor, sediment, cyst
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com Continuing product improvements may necessitate changes without notice. © 2010 ABS
E-31
WATER SYSTEMS
Everpure Replacement Filters
.75
6
Sediment, chlorine, taste, odor, cyst, scale
EV910066 IN-6 CGS
700
.75
6
Taste, odor, scale
EV910067 IN-6 PGS
6 mo.
.75
6
Scale
EV910068 IN-10-CK
5,000
EV910069 IN-10-CS
3,900
.5
6
Taste, odor
EV910071 IN-10-CC
2,000
.75
6
Taste, odor
EV910072 IN-10-NSS
6-12 mo
.75
5
6
Sediment
EV910073 IN-10-CL1
750
.75
1
6
Taste, odor, lead, cyst
EV910075 IN-9 CFS
1,500
.75
5
6
Taste, odor, scale
EV910076 IN-15-CF
5,000
.75
5
6
Taste, odor
EV910077 IN-15-CFS
5,000
.75
5
6
Taste, odor, scale
EV910078 IN-15-CR
650 gr.
.75
6
Hardness, taste, odor
EV910079 IN-10-UV
12 mo.
.75
12
Bacteria, viruses
EV910086 IN-12
4,800
.75
6
Sediment, chlorine, taste, odor, cyst, scale
EV910502 CB20-124E
15,000
5
1
Chloramine, chlorine, taste, odor, cyst
EV910521 CB20-302E
20,000
5
1
Chloramine, chlorine, taste, odor, cyst
EV910534 CB20-312E
60,000
5
1
Chloramine, chlorine, taste, odor, cyst
EV910541 SO-10
N/A
2
N/A
1
Hardness, scale
EV910542 SO-20
1500 gr.
2
N/A
0
Hardness, scale
EV910545 SO-204
N/A
2
N/A
0
Hardness, scale
EV910700 QCP 10L
500
.5
5
12
Sediment
EV910700 QCP 10L
500
.5
12
Chlorine, taste, odor, lead
5
12
Chlorine, taste, odor, lead
12
Chloramine, taste, odor
EV910008 IN-10
N/A
Case Qty.
GPM Flow Rate
2,400
Part Number Model
Micron Rating
Gallon Capacity
Sorted by Part Number
Reduces/Eliminates
Taste, odor, scale, slime
EV910701 QCP 10GAC
1,700
.5
EV910701 QCP 10GAC
2,500
.5
EV910702 QCP 10SED
--
.5
5
0
Chloramine, taste, odor
EV910702 QCP 10SEDS
Depends
.5
5
0
Sediment, taste, odor
EV910703 QCP 10TSGAC
2,500
.5
5
0
Scale
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com E-32
Continuing product improvements may necessitate changes without notice. © 2010 ABS
WATER SYSTEMS
Everpure Replacement Filters
.5
Case Qty.
1,700
Micron Rating
GPM Flow Rate
EV910703 QCP 10TSGAC
Gallon Capacity
Part Number Model
Sorted by Part Number
Reduces/Eliminates
0
Chloramine, taste, odor, scale
50/5
0
Sediment
EV910837 20" x 4" Big Bowl
N/A
EV910840 20" x 4" Big Bowl
N/A
20
25/1
6
Sediment
EV953412 EC110 10" Slimline
N/A
5
10
0
Sediment
EV953426 EC210 20" Slimline
N/A
10
10
0
Sediment
EV953430 10" ECPI
N/A
1
Sediment
EV953433 20" ECPI
N/A
1
Sediment
EV953436 20" ECPI Big Bowl
N/A
Sediment
EV960700 7DBG
Depends
1.7
EV960701 7DM
1600 gr.
EV960702 7NE
40
1
Extraordinary taste and odor, high turbidity
.5
0
Scale, high mineral content, low volume application
Depends
.5
1
Buffer/neutralizer for acidic (low pH) water, taste, odor
EV960703 7OF
Depends
.5
1
Iron, sulfer, stains
EV960704 7SO
2000 gr.
.5
1
High mineral content, low volume application
EV960705 7TO
30,000
1.5
6
Extraordinary taste and odor, high turbidity
EV960710 ESO 6
Depends
.5
0
Hardness, buffering, chlorine, cyst, iron, sediment, scale, taste, odor
EV960725 ESO 7
Depends
.5
0
Hardness, buffering, chlorine, cyst, iron, sediment, scale, taste, odor
EV961222 I20002
9,000
1.7
.5
0
Sediment, chlorine, taste, odor, cyst, microbial control, scale
EV961232 I40002
12,000
1.7
.5
0
Sediment, chlorine, taste, odor, cyst, microbial control, scale
EV961250 BH2
3,000
.5
.5
0
Sediment, chlorine, taste, odor, cyst, microbial control, scale
EV961256 MC2
9,000
1.7
.5
0
Class I particulates, chlorine, taste, odor, cyst
EV961310 XC2
12,000
1.7
.5
0
Class I particulates, chlorine, taste, odor, cyst
EV961321 MH2
9,000
1.7
.5
0
Sediment, chlorine, taste, odor, cyst, microbial control, scale
EV961706 2CB5K
3,000
1
5
0
Sediment, chlorine, taste, odor, high turbidity, microbial control (for low flow/pressure)
EV961711 4CBS
6,000
1.7
5
0
Sediment, chlorine, taste, odor, high turbidity (for low flow/pressure)
EV961721 4CB5S
6,000
1.7
5
0
Sediment, chlorine, taste, odor, scale
EV961722 2CB5S
3,000
1
5
0
Sediment, chlorine, taste, odor, scale
EV961736 4CB5K
6,000
1.7
5
0
Sediment, chlorine, taste, odor, high turbidity, microbial control (for low flow/pressure)
EV961776 7CB5K
10,000
2.5
5
0
Sediment, chlorine, taste, odor, high turbidity, microbial control (for low flow/pressure)
EV961802 OCS2
1,500
.5
.5
0
Sediment, chlorine, taste, odor, cyst, microbial control, scale
EV961811 7CB5
10,000
2.5
5
0
Sediment, chlorine, taste, odor, high turbidity (for low flow/pressure)
EV961821 7CB5S
10,000
2.5
5
0
Sediment, chlorine, taste, odor, scale
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com Continuing product improvements may necessitate changes without notice. © 2010 ABS
E-33
WATER SYSTEMS
Everpure Replacement Filters
Part Number Model
Gallon Capacity
GPM Flow Rate
Micron Rating
Case Qty.
Sorted by Part Number
EV961901 OW200L
480
.5
.5
0
Sediment, chlorine, taste, odor, lead, scale, cyst, THMs
EV962828 MC2 Quad Kit
36,000
6.7
.5
0
Class I particulates, chlorine, taste, odor, cyst
EV962829 XC2 Quad Kit
48,000
6.7
.5
0
Class I particulates, chlorine, taste, odor, cyst
EV963401 OW2-Plus
1,000
.5
.5
0
Sediment, chlorine, taste, odor, cyst, microbial control, lead, scale
EV963501 OW4-Plus
2,000
.5
.5
0
Sediment, chlorine, taste, odor, cyst, microbial control, lead, scale
EV963701 Microguard Pro 2
2,200
1
.15
0
Sediment, chlorine, taste, odor, bacteria, asbestos, cyst
EV963702 Microguard Pro 4
3,600
1
.15
0
Sediment, chlorine, taste, odor, bacteria, asbestos, cyst
EV979902 SS-10
6 mo.
6
N/A
0
Hardness, scale
EV979932 SS-IMF
N/A
6
N/A
1
Hardness, scale
27,000
5
.5
0
Class I particulates, chlorine, taste, odor, cyst
EV997042 MC2 Triple Kit
Reduces/Eliminates
Everpure Water System Cleaning Accessories Part Number
Description
EV960800
4JT flushing/sanitizing cartridge for ScaleKleen™, bleach, or other sanitizing agent
EV960810
2JT flushing/sanitizing cartridge
EV979831
ScaleKleen scale remover, 1.75 oz.
EV979833
ScaleKleen scale remover, 7 oz.
EV979835
ScaleKleen scale remover, 2.2 lb
EV910091
HFC-10 deliming agent
EV910091
EV960800
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com E-34
Continuing product improvements may necessitate changes without notice. © 2010 ABS
WATER SYSTEMS
Everpure Water System Heads
EV910721
EV910722
EV927222
EV910723
EV927224
EV433921
EV925617
EV925924
EV933611
EV927223
EV927241
EV933726
Model
Part Number
QCP1 Single Head
EV910721
Yes
No
1/4" QCF
No
No
QCP2 Twin Head
EV910722
Yes
No
1/4" QCF
No
No
QCP3 Triple Head
EV910723
Yes
No
1/4" QCF
No
No
QCPC (1 head no shut-off)
EV910720
No
No
1/4" QCF
No
No
QL1 Single Head
EV925618
No
Yes
3/8" MPT
No
No
QL1 Single Head
EV925617
No
Yes
3/8" QCF
No
No
QL3B Single Head
EV925924
Yes
Yes
3/8" MPT
No
No
QC71 Single Head
EV927241
Yes
Yes
3/8" MPT
Yes
Yes
QC71 Twin Parallel Head
EV927222
Yes
Yes
3/4" MPT
Yes
Yes
QC71 Twin Plumbed Head
EV927224
Yes
Yes
3/4" MPT
Yes
No
QC71 Triple Parallel Head
EV927223
Yes
Yes
3/4" MPT
Yes
Yes
QC71 Quad Parallel Head
EV933611
Yes
Yes
3/4" MPT
Yes
Yes
QC71 Quad Head
EV933726
Yes
Yes
3/4" MPT
Yes
Yes
Claris Head 3/8" BSP
EV4339-21
Yes
Yes
3/8" BSP
Yes
No
Claris Head 3/8" QCF
EV4339-23
Yes
Yes
3/8" QCF
Yes
No
Claris Head 1/4" QCF
EV4339-25
Yes
Yes
1/4" QCF
Yes
No
Shut-Off Valve Mtg. Bracket Connection Flushing Valve Pressure Gauge
QCF = quick connect fitting, comparable to John Guest fittings
Everpure Water System Accessories Part Number
Description
DEV701344
Smartworks water test kit
EV982010
Faucet kit
EV8300101
Bottled water delivery system
EV907550
Filter usage monitor
EV933650
Surge tank, 9 gallon with fittings and tubing
EV311469
Spacer for SS-IMF cartridge
EV126122
Titration kit for Claris system Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com
Continuing product improvements may necessitate changes without notice. © 2010 ABS
E-35
WATER SYSTEMS
Bottled Water Dispenser At just 6" x 8" the Flojet Inlet Bottled Water Dispensing System is compact, affordable and perfect for dispensing bottled water to coffee machines, beverage dispensers, vending machines and carts in remote locations where water supply is inaccessible. BW1000A
This system has a universal seal cap, float switch for automatic shut-off when bottle is empty, built-in check valve to prevent back flow, and 20' discharge hose. Available in single or dual inlet. The dual inlet model has a “T” to draw from two bottles simultaneously. Flow rate: 1.0 GPM. Maximum pressure: 40 psi.
Part Number
Description
BW1000A
Single inlet, 1 GPM pump, 115 Volt, 20' discharge hose 1/4" OD
BW1020A
Dual inlet, 1 GPM pump, 115 Volt, 20' discharge hose 1/4" OD
BW3000A
Single inlet, 12V DC with 12" lead wires
BW3020A
Dual inlet, 12V DC with 12" lead wires
BW1520A
Dual inlet, appliance controller interface, 115 Volt
BW3520A
Dual inlet, appliance controller interface, 12 Volt DC with 12" lead wires
21000633A
Conversion kit, single to dual inlet
91006466A
Conversion kit, legacy to A.C. interface
21000006B
Appliance controller
91006698A
Daisy chain (multi-hook up) 4-6 pin RJ-1, 9' cable
Appliance Controller Unit is designed to work with applications drawing water from a reservoir or a bottled water system such as coffee machines and carbonator pumps at soft drink kiosks. It will sense water empty signal (0-5 VDC) coming from the water level sensor and turn connected devices ON or OFF. Audible alarm. 1 year warranty. Appliance controller can be mounted over or under the counter. Operating temperature: 32˚ F to 158˚ F. RJ-11 4 pins: daisy chain configuration. RJ-11 6 pins: BW interface. 6 pin RJ-11 cable: 9'. 2 AC outlets. 115V.
Part Number
Description
91006467A
Appliance controller
91006698A
4-6 pin RJ-11 cable, 6'
Lancer is a registered trademark of Lancer Corporation, San Antonio, Texas. SHURflo is a registered trademark of SHURflo, LLC, Cypress, California. McCann’s is a registered trademark of McCann’s Engineering, a Manitowoc Company, Los Angeles, California. Procon is a registered trademark of Procon Products, Standex International Corporation, Murfreesboro, Tennessee. Fluid-o-Tech is a registered trademark of Fluid-o-Tech International, Inc., Plantsville, Connecticut. Flojet is a registered trademark of ITT Industries, Foothill Ranch, California. CUNO, ScaleGARD, and Recipe Quality Water are trademarks of CUNO Incorporated, a 3M Company, Meriden, Connecticut. 3M is a trademark of 3M Company. Selecto is a registered trademark of Selecto, Inc., Suwanee, Georgia. Everpure is a registered trademark of Everpure, Inc., Hanover Park, Illinois.
Advanced Beverage Solutions • Ph: 877-814-2271 • Fax: 847-524-1710 • E-mail:
[email protected] • Visit us online at www.absone.com E-36
Continuing product improvements may necessitate changes without notice. © 2010 ABS
