Transcript
Illustrated Parts List 26" RIDING MOWER SIDE DISCHARGE ELECTRIC START
Catalog No.
WE261
IMPORTANT: Read and follow all Safety Rules and Instructions before op er at ing this equipment. Patents Pending
433203
RIDING MOWER - -CATALOG NO. WE261 SCHEMATIC BATTERY
SCH21
FUSE-5A RED
RED
BLACK
STARTER RELAY
STARTER
RED
M
FUSE-40A WHITE
WHITE BLACK
B S M WHITE
A1 L A2
BLACK/WHITE
G
A CLUTCH / BRAKE (PEDAL UP)
ATTACHMENT CLUTCH (CLUTCH OFF)
BLACK/WHITE
BLACK/WHITE
B
D
C
E
F
RED
BLACK
SAFETY START MODULE SEAT SWITCH (NOT OCCUPIED)
GREEN
BLACK
BLACK
GRAY
REVERSE SWITCH NOT IN REVERSE
SHORTING CONNECTOR BLACK
YELLOW
IGNITION UNIT
BLACK/WHITE
SPARK PLUG GAP CHARGING SYSTEM OUTPUT . 5 AMP DC @ 3600 RPM
28 VOLTS AC MIN. @ 3600 RPM (CHARGING SYSTEM DISCONNECTED)
RED
DIODE
F
E
D
C
B
STATOR
A
SAFETY START MODULE VIEWED FROM MATING SIDE
REMOVABLE CONNECTIONS
IGNITION SWITCH POSITION
CIRCUIT
OFF RUN/OVERRIDE
M+G+A1 B+A1
RUN START
B+A1 B + S + A1
“MAKE”
L+A2
WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE RE-INSTALLED TO PROPERLY SECURE YOUR WIRING.
27
NON-REMOVABLE CONNECTIONS
RIDING MOWER - -CATALOG NO. WE261 ELECTRICAL
LRV1
5 6
11
4
3
13
2
12
10
1
9
8
7
28
RIDING MOWER - -CATALOG NO. WE261 ELECTRICAL
KEY PART NO. NO.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12 13
BATTERY, 12V, 8AH FOAM, POLYURETHANE SWITCH, IGN, DLTA, P-IN, ROS KEY, MOLDED FUSE, 5A FUSE, 40A SWITCH, PLUNGER, NO, OLIVE RELAY, 40A SWITCH, INTLK,CL, MWR, GRY SWITCH, INTERLOCK, NONC,GRAY MODULE, STARTING, RECOIL, LRV SWITCH, SEAT, DP, ROS HARNESS, IGN, ELECTSTART, LRV
423264 425416 193350 411934 433330 425937 160784 431542 109553X 176138 431846 192749 428477
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
29
RIDING MOWER - -CATALOG NO. WE261 CHASSIS
44
35 36
18
10
42
39
43
34
39 37
27
38
12
40
41
45
33
31
45
45
13
29 30
41
45 49
17 28
11
40
7
32
45
26
16 45
24
19
45
46 14
20 45 46 48
46 2 47
1
6 21
3
46
45 9
45 48 46
15 23 4 22
25
8
5
46 45
LRV-Chassis_1_r1
24
30
RIDING MOWER - -CATALOG NO. WE261 CHASSIS
KEY PART NO. NO.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 -19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49
WELDMENT, CHASSIS SUPPORT, AXEL LH SUPPORT, AXEL RH SHIELD, TRANSAXLE FRONT BRACE, AXLE CROSS COVER, FRICTION DRIVE PLATE, ENGINE BRACKET, CHASSIS FRONT BRACKET, STEERING SUPPORT PAN, SEAT BRACKET, SWITCH MOUNTING BOOT, DUST COVER, FOOT REST STRUCTURE, FOOT REST SUPPORT, FOOT REST FENDER, CONTROL GUARD, ENGINE ENGINE (NON-CALIFORNIA) ENGINE (CALIFORNIA) KEEPER, BELT BRACKET, BATTERY LEVER, SWITCH DECK CLUTCH ASM KNOB SCREW, NO. 10 BOLT, CARRIAGE 1/4-20 X 3 NUT, 1/4-20 SPACER, ENGINE DISC, FRICTION ASM BOLT, SCKT HD 3/8-24 X 1 .25 BEARING SPACER, NEUTRAL BOLT, 3/8-16 X .280 SPRING, SEAT SPRING BOLT, 1/4-20 X 1 1/2 BOLT, SHOULDER WASHER, 17/32 X 1 3/16 KNOB, SEAT SPACER BUSHING, NYLON SNAP NUT, LOCK BOLT, 5/16-18 SHOULDER NUT, 5/16-18 SEAT BOLT, 5/16-18 X 3/4 BOLT, 5/16-18 X 1/2 SCREW BEARING FLANGE BALL SCREW 5/16-18 X1
428048 428247 428244 428346 428110 428109 428040 428576 428856 195530 174648X431 428248 428251X665 428250 428249 428241X665 428348 428047 432389 428986 428046 429815 428826 149846 416358 72140424 73510400 430087 428301 430817 430470 430469 150406 124181X 121250X 72050412 127018X 19171912 166369 134300 121248X 123976X 171852 73800500 428243 17000512 17490508 86777 408981 17060516
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
31
RIDING MOWER - -CATALOG NO. WE261 DRIVE
67
61 68 69
65
63
58
64
62 66
60
24 58 25 70
35
34 70 58
26
8
8 7
64 70 11
36 27
13
8
31 14
43 29
3 70 71
33
28
63
14 13
17
3
70
15
6
32
38
11 10
15
7
4 1
21
19
70
38
54
5 20
57
52 50
55
53
70 38 24
8
56
18
2
23
70
39
41
12
16
2
37 42 40
30
47 46 37 8 6
51 22 70
49
48
45
59 71
5 4
2 1
LRV-Drive_1_r1
32
2
3
RIDING MOWER - -CATALOG NO. WE261 DRIVE
KEY PART NO. NO.
DESCRIPTION
1 2 3 4 5 6 7 8 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
WHEEL ASM (REAR) WASHER, 16 GA. E-CLIP KEY. SQUARE WELDMENT. DRIVE AXLE CHAIN DRIVE SPROCKET. 9 TOOTH SPLINED RING, SNAP DIFFERENTIAL ASM WASHER, THRUST CHAIN, PRIMARY DRIVE BUSHING BRACKET, CARRIER BEARING ASM SHAFT INPUT WHEEL, FRICTION A5M ARM, SHIFT ROD, BYPASS BRACE CARRIER REAR SPRING, CARRIER SPRING, BRAKE SPRING, BYPASS BRACE CARRIER BOX LINK, SHIFT ARM. CLUTCH WELDMENT SHIFT LEVER SUPPORT, SHIFT LEVER WASHER, NYLON HUB SHIFT LEVER SPACER, NYLON MNTG BRKT. SHIFT ARM BRACKET, SHIFTER FLEX TUBE SHIFT ARM GRIP, HANDLE BOLT, CARRIAGE - 114-20 X 3/4 NUT NYLON LOCK 114-20 BOLT, SHOULDER BOLT, 1/4-20 X 3/4
428268X613 121748X 12000001 123583X 427939 428069 427873 12100009 428876 1370H 430645 430845 427946 9159R 427926 428106 424759 430870 427997 428077 428076 431374 427995 429303 429816 429053 428302 174840 183900 429055 428464 428461 428462 196492 72110406 73800400 165492 74780412
KEY PART NO. NO.
DESCRIPTION
40 41 42 43 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71
WASHER, LOCK WASHER FLAT WASHER, SERRATED NUT, CROWN LOCK 114-20 SCREW 1/4-20 X 2 114 WASHER SCREW, 1/4-20 X 1 1/2 PLATE BRAKE ANTI - ROTATE SPRING, BRAKE RETURN ARM, BRAKE SPACER RETURN CALIPER, BRAKE ASM PIN, DOWEL 1/4 PLATE, BRAKE PAD PUCK BRAKE ROTOR, BRAKE CAP, BRAKE CALIPER PIN, RETAINER BOLT, 5/16-16 X 112 CABLE, BRAKE WELDMENT, PEDAL ROD, PARKING BRAKE PIN, .25 X .75 CLEVIS PIN, 1/16 DIA. COTTER BRACKET, BRAKE SUPPORT COVER PEDAL COVER, BRAKE PEDAL SCREW, 1/4-20 X 1/2 BRAKE CABLE MOUNT BOLT, 5/16-18 X 3/4 CAP HUB AXLE
10040400 19091210 166002 73680400 17490436 19091016 17490420 430249 430245 428021 430247 428078 77010810 428019 428017 428014 428016 4497H 17490508 428460 427945 429678 77100812 76020208 429325 429694 429693 17490408 428070 17000512 104757X613
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
33
RIDING MOWER - -CATALOG NO. WE261 STEERING 27
26
25 24 23
22
28 21
18 19
17
16
4
13
14 10 20
12 8
8
11
9 9
2 6
7 30
19
15
9
2 8 6
2
7
3
4 1
5 29 4
LRV-Steering_1_r1
1
34
3
2
30
RIDING MOWER - -CATALOG NO. WE261 STEERING
KEY PART NO. NO.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
WHEEL ASM (FRONT) E-CLIP WASHER, HARDENED WASHER, 1/4 X 3/4 SPINDLE, RH ASHER, HARDENED THRUST USHING, STEERING COLUMN PIN, 5/64 X 3/4 COTTER WASHER WELDMENT, LWR STRG SHAFT LINK, STRNG LH LINK, STRNG RH BOLT, 5/16-18 X 1 1/2 WASHER NUT, 5/16-18 BUSHING, STEERING SNAP SUPPORT, UPPER STEERING BUSHING, UPPER STEERING BOLT, 5/16-18 X 3/4 CLIP, RETAINER SPRING COVER, STEERING COLUMN SHAFT, STEERING ADAPTER, STEERING WHEEL WASHER, 9/16 X 2 3/8 12 GA. NUT, JAM LOCK 1/2-20 WHEEL, STEERING CAP, STEERING WHEEL CLIP, RETAINER SPRING SPINDLE, LH CAP, HUB, AXLE
428269X613 12000001 188967 121749X 428034 6266H W 3366R B 421076 19131414 428057 428035 428036 74780524 19131016 73800500 428044 428252 195227 17000512 428045 428347 428213 186737 19183812 73940800 414851X418 414852X418 199849 428033 104757X613
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
35
RIDING MOWER - -CATALOG NO. WE261 MOWER DECK 36
6
7 37 39 17 20 19
9
40
39 8 17 37
36
32
31
5 28
35 38 4
27
33
34
10 27 26 3
2 11 41
25
13 24
12 42
1 23
19
18 17
15 16 14
LRV-Deck_1_r1
20
19
21 16 17
18
29 30
36
22
19
RIDING MOWER - -CATALOG NO. WE261 MOWER DECK
KEY PART NO. NO.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42
DECK, 26" MANDREL ASM KEEPER, BELT PULLEY, MANDREL BELT COVER, MANDREL LIFT ASM, DECK LINK, DECK LIFT LINK, ADJUSTABLE DEFLECTOR SUPPORT, DEFLECTOR ROD, HINGE SPRING, TORSION ARM, MOWER SUPPORT NUT, LOCK STUD WASHER PIN BOLT, SHOULDER PIN WASHER, 17/32 X 1 3/16 LINK, DECK NUT, LCK 3/8-16 SPRING, DECK PIN SPACER, MANDREL BOLT, MANDREL NUT, LOCK BLADE BOLT, BLADE PULLEY, IDLER GUARD, IDLER KEEPER, BELT IDLER BOLT, 3/8-16 X 1 1/2 ARM, BRAKE SCREW, 1/4-20 X 5/8 NUT, 3/8-16 FLANGE ARM, IDLER BOLT, 5/16-18 X 1/2 WASHER, 16 GA. CAP, SLEEVE NUT, PUSH
428193 192870 432520 432594 428578 428242 429395 429195 429397 428146 428968 131491 197026 418863 73900500 195161 19191912 194209 196539 194208 19171912 429350 73930600 429531 4497H 187690 173984 400234 428500 193003 193197 141043 193414 72110612 199470 137729 73900600 428435 17490508 19171616 105304X 110452X
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
37
DECALS
38
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
*5
*California models only.
DECAL, STEERING WHEEL DECAL, V-BELT SCH 30" DECAL, WARN. DEFLECT/CTFGR DECAL, DECK/DEFLECTOR DECAL, SPARK ARRESTOR DECAL, BYPASS
1 2 3 4 *5 --
430588 433596 425113 430589 424102 432479
DESCRIPTION
4
2 3
4
KEY PART NO. NO.
1
RIDING MOWER - -CATALOG NO. WE261
• Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the instructions, to operate the machine. • Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blade. • Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing.
I. GENERAL OPERATION
WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. WARNING: Do not coast down a hill in neutral, you may lose control of the riding mower. WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. WARNING:This unit is not intended for towing, or use of wheel weights. Only use attachments designed specifically for this riding mower. WARNING: Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
3
• Never direct discharged material toward anyone. Avoid discharging material against a wall or obstruction. Material may ricochet back toward the operator. Stop the blade when crossing gravel surfaces. • Do not operate machine without the entire grass catcher, discharge chute, or other safety devices in place and working. • Slow down before turning. • Never leave a running machine unattended. Always turn off blade, set parking brake, stop engine, and remove keys before dismounting. • Disengage blade when not mowing. Shut off engine and wait for all parts to come to a complete stop before cleaning the machine, removing the grass catcher, or unclogging the discharge chute. • Operate machine only in daylight or good artificial light. • Do not operate the machine while under the influence of alcohol or drugs. • Watch for traffic when operating near or crossing roadways. • Use extra care when loading or unloading the machine into a trailer or truck. • Always wear eye protection when operating machine. • Data indicates that operators, age 60 years and above, are involved in a large percentage of riding mower-related injuries. These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury. • Keep machine free of grass , leaves or other debris build-up which can touch hot exhaust / engine parts and burn. Do not allow the mower deck to plow leaves or other debris which can cause build-up to occur. Clean any oil or fuel spillage before operating or storing the machine. Allow machine to cool before storage.
DANGER: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death.
SAFETY RULES
12.14.09 CL
Printed in the U.S.A.
