Wf43gtibedbt0

Transcript

Winstar Display Co., LTD 華凌光電股份有限公司 住址: 407 台中市中清路 163 號 No.163 Chung Ching RD., Taichune, Taiwan, R.O.C WEB: http://www.winstar.com.tw E-mail: [email protected] Tel:886-4-24262208 Fax：886-4-24262207 SPECIFICATION CUSTOMER : MODULE NO.: WF43GTIBEDBT0# APPROVED BY: ( FOR CUSTOMER USE ONLY ) PCB VERSION: SALES BY APPROVED BY CHECKED BY DATA: PREPARED BY 叶慧芬 ISSUED DATE: 2013-3-18 第 1 頁，共 20 頁 Winstar Display Co., LTD MODLE NO： 華凌光電股份有限公司 DOC. FIRST ISSUE RECORDS OF REVISION VERSION DATE 0 2013.3.18 REVISED PAGE NO. SUMMARY First issue 第 2 頁，共 20 頁 Contents 1. Module Classification Information 2. Summry 3. General Specification 4. Absolute Maximum Ratings 5. Electrical Characteristics 6. DC Characteristics 7. Interface Timing 8. Optical Characteristics 9. Interface 10. Block Diagram 11. Reliability 12. Touch panel Information 13. Contour Drawing 14. Package specification 15. Initial Code For Reference 第 3 頁，共 20 頁 1.Module Classification Information
    W F 43 G T I B E D B T 0 1 ○ 2 ○ 3 ○ 4 ○ 5 ○ 6 ○ 7 ○ 8 ○ 9 ○ 10 ○ 11 ○ 12 ○ # 13 ○ Brand：WINSTAR DISPLAY CORPORATION Display Type：H→Character Type, G→Graphic Type F→TFT Type Display Size：4.3 ” TFT Model serials no. Backlight Type： F→CCFL, White T→LED, White  LCD Polarize I→Transmissive, W. T, 6:00 Type/ Temperature L→Transmissive, W.T,12:00 range/ Gray Scale Inversion Direction  A：TFT LCD B：TFT+FR+CONTROL BOARD C：TFT+FR+A/D BOARD D：TFT+FR+A/D BOARD+CONTROL BOARD E：TFT+FR+POWER BOARD F：TFT+CONTROL BOARD  Solution: A: 128160 B:320234 C:320240 D:480234 H:1024600 I:320480 J:240320 K:800600 9 D: Digital L：LVDS ○ 10 Interface： N：without control board A：8Bit ○ G：TFT+FR H：TFT+D/V BOARD I：TFT+FR+D/V BOARD J：TFT+POWER BD E:480272 L:240400 F: 640480 G: 800480 M :1024768 B：16Bit 11 TS： ○ N：Without TS T：resistive touch panel C：capacitive touch panel 12 Version ○ 13 Special Code #:Fit in with ROHS directive regulations ○ 第 4 頁，共 20 頁 2.SUMMARY This technical specification applies to 4.3’ color TFT-LCD panel. The 4.3’ color TFT-LCD panel is designed for camcorder, digital camera application and other electronic products which require high quality flat panel displays. This module follows RoHS. 3.General Specification Item Dimension Unit 480 x RGBx272(TFT) dots 106.7 x 69.6 x 5.9 mm Active area 95.04 x 53.856 mm Dot pitch 0.066 x 0.198 mm Dot Matrix Module dimension LCD type TFT, Negative, Transmissive View Direction Gray Scale Inversion Direction Backlight Type 12 o’clock 6 o’clock LED,Normally White SSD1963 Controller IC Interface Digital 8080 family MPU *Color tone slight changed by temperature and driving voltage. 4.Absolute Maximum Ratings Item Symbol Min Typ Max Unit Operating Temperature TOP -20 － +70 ℃ Storage Temperature TST -30 － +80 ℃ Note: Device is subject to be damaged permanently if stresses beyond those absolute maximum ratings listed above 1. Temp. ≦600C, 90% RH MAX. Temp. ＞ 600C , Absolute humidity shall be less than 90% RH at 600C 第 5 頁，共 20 頁 5.Electrical Characteristics 5.1. Operating conditions: Item Symbol Condition Min Typ Max Unit VDD － 3.1 3.3 3.5 V Supply Voltage For Logic 5.2 LED driving conditions Parameter LED current Power Consumption LED voltage LED Life Time Symbol Min. VBL+ 30 - Typ. 20 640 32 50,000 Max. 680 34 - Unit mA mW V Hr Remark Note 1 Note 2,3,4 Note 1 : There are 1 Groups LED K A Note 2 : Ta = 25 ℃ Note 3 : Brightess to be decreased to 50% of the initial value Note 4 : The single LED lamp case 6. DC Characteristics Parameter Rating Symbol Low level input voltage VIL Hight level input voltage VIH Min Typ 0 - 0.7 VDD - 第 6 頁，共 20 頁 Unit Max 0.3 VDD VDD V V Condition 7. Interface Timing 7.1.1 8080 Mode The 8080 mode MCU interface consist of CS#, D/C#, RD#, WR#, D[23:0] and TE signals (Please refer to Table 6-1 for pin multiplexed with 6800 mode). This interface use WR# to define a write cycle and RD# for read cycle. If the WR# goes low when the CS# signal is low, the data or command will be latched into the system at the rising edge of WR#. Similarly, the read cycle will start when RD# goes low and end at the rising edge of RD#. 7.1.2 8080 Mode Write Cycle 第 7 頁，共 20 頁 7.1.3 Pixel Data Format 第 8 頁，共 20 頁 8. Optical Characteristics Item Symbol Condition. Min Typ. Max. Tr 10 20 Response time θ=0°、Φ=0° 15 30 Tf At optimized Contrast ratio CR 400 500 viewing angle Wx 0.24 0.29 0.34 Color Chromaticity White θ=0°、Φ=0 Wy 0.26 0.31 0.36 60 70 ΘR Hor. 60 70 ΘL Viewing angle CR≧10 40 50 ΦT Ver. 60 70 ΦB Brightness - - 240 - 350 Unit .ms .ms Remark - Note 4 Note 3 Note 2,5 Deg. cd/m 2 Note 1 Center of display Ta=25±2℃, IL=20mA Note 1: Definition of viewing angle range Fig. 8-1 Definition of viewing angle Note 2: Test equipment setup: After stabilizing and leaving the panel alone at a driven temperature for 10 minutes, the measurement should be executed. Measurement should be executed in a stable, windless, and dark room. Optical specifications are measured by Topcon BM-7 luminance meter 1.0° field of view at a distance of 50cm and normal direction. 第 9 頁，共 20 頁 Fig. 8-2 Optical measurement system setup Note 3: Definition of Response time: The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time, Tr, is the time between photo detector output intensity changed from 90%to 10%. And fall time, Tf, is the time between photo detector output intensity changed from 10%to 90% Note 4: Definition of contrast ratio: The contrast ratio is defined as the following expression. Note 5: Definition of color chromaticity (CIE1931) Color coordinates measured at center point of LCD. Note 6: All input terminals LCD panel must be ground while measuring the center area of the panel. 第 10 頁，共 20 頁 9. Interface 9.1. LCM PIN Definition Pin Symbol 1 GND 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 VDD BL E D/C WR RD D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 NC NC CS RST NC X1 Y1 X2 Y2 DIP ON I/O Function Remark Systen ground pin of the IC. Connect to systen ground. Power Supply : +3.3V Backlight control signal , H: On \ L:Off Data/Command select Write strobe signal Read strobe signal Data bus Data bus Data bus Data bus Data bus Data bus Data bus Data bus Data bus Data bus Data bus Data bus Data bus Data bus Data bus Data bus No connection No connection Chip select Hardware reset No connection Right electrode Bottom electrode Left electrode Top electrode Display control H: On \ L:Off 第 11 頁，共 20 頁 D15 X1 Y1 X2 Y2 D/C BL_E RST D0 DIPON VDD GND CS WR RD VDD VSS VSYNC HSYNC DISP DCLK DE R7~R0 G7~G0 B7~B0 X1 Y1 X2 Y2 LEDLED+ RESET BL TFT LCD 480xRGBx272 FPC inferface LCD control board & Backlight control 第 12 頁，共 20 頁 TP 10. BLOCK DIAGRAM 11.Reliability Content of Reliability Test (Wide temperature, -20℃~70℃ ℃) Environmental Test Test Item Content of Test High Temperature storage Endurance test applying the high storage temperature for a long 80℃ time. 200hrs Endurance test applying the high storage temperature for a long -30℃ time. 200hrs Endurance test applying the electric stress (Voltage & Current) 70℃ and the thermal stress to the element for a long time. 200hrs Endurance test applying the electric stress under low temperature -20℃ for a long time. 200hrs The module should be allowed to stand at 60℃,90%RH max 60℃,90%RH For 96hrs under no-load condition excluding the polarizer, 96hrs Then taking it out and drying it at normal temperature. The sample should be allowed stand the following 10 cycles of -20℃/70℃ operation 10 cycles -20℃ 25℃ 70℃ Low Temperature storage High Temperature Operation Low Temperature Operation High Temperature/ Humidity Operation Thermal shock resistance Test Condition Note 2 1,2 —— 1 1,2 —— 30min Vibration test Static electricity test 5min 30min 1 cycle Endurance test applying the vibration during transportation and Total fixed amplitude : 3 using. 15mm Vibration Frequency : 10~55Hz One cycle 60 seconds to 3 directions of X,Y,Z for Each 15 minutes Endurance test applying the electric stress to the terminal. —— VS=800V,RS=1.5kΩ CS=100pF 1 time Note1: No dew condensation to be observed. Note2: The function test shall be conducted after 4 hours storage at the normal Temperature and humidity after remove from the test chamber. Note3: Vibration test will be conducted to the product itself without putting it in a container. 第 13 頁，共 20 頁 12. Touch panel Information Y2 X2 X1 2. 3± 0. 3 3M467 T=0. 10mm 3M467 T=0. 10mm ITO Fi l m 0. 188mm(雾面) Y1 Y1 1 Y2 I TO Gl ass T=0. 7mm X1 59. 3± 0. 3( 背背背背) 66. 8± 0. 3( 背背背背) X2 Pr ot ect gl ue 3 3M双面背 T=0. 05mm Pi n 4 44. 89± 0. 5 See Det ai l "A" See Det ai l "B" See Det ai l "C" 小小小 5. 87± 0. 5 7± 0. 5 Pi n 1 6. 2± 0. 3 R1 .5 4± 0. 3 20 19± 0. 5 3 3 3 R0. 16- 4. 75± 0. 1 导 电 面 导 电 面 1 DETAI L"A" 4/1 导 电 面 3. 8± 0. 3 8?0 .3 0. 76 1. 52 2. 28 4. 1± 0. 3 67. 2± 0. 2( OD) 57. 5± 0. 2( VA) 55. 5± 0. 2( AA) Y2 X2 2. 3± 0. 3 105. 1± 0. 3(背背背背) 100. 5± 0. 3(背背背背) Y1 X1 4 1. 1± 0. 15 3. 4± 0. 2 （含背含含） 4. 4± 0. 2 105. 5± 0. 2(OD) 98. 7± 0. 2( VA) 96. 7± 0. 2( AA) 1. 3± 0. 3 2. 4± 0. 2 3. 4± 0. 2 FRONT VI EW 0. 10± 0. 03 DETAI L"B" 4/1 W- 0. 5± 0. 05*4 P- 1. 25± 0. 05*3 0. 5± 0. 1*2 DETAI L"C" 4/1 第 14 頁，共 20 頁 Oper at i on Temper at ur e - 20~+70℃ St or age Temper at ur e - 30~+80℃ 13.Contour Drawing PI N 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 DESC GND VDD BL E D/ C WR RD D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 NC NC CS RST NC X1 Y1 X2 Y2 DI P ON A 480 RGB X 272 4-? 3.5 PTH K A RGB CIRCUIT DIAGRAM(10Diceㄘ SCALE 1:100 The non-specified tolerance of dimension is 1 2 3 4 5 6 7 8 9 第 15 頁，共 20 頁 0.3mm. 14. Package specification LCM Model LCM 包裝規格書 Approve Check Contact LCM Packaging Specifications DATE 12'11/15 初版 12'11/15 版次 Ver WF43GTIBEDBT0# Drawing NO. 0 1.包裝材料規格表 包裝材料規格表（ ）:(per carton) 包裝材料規格表（Packaging Material） Item Model 成品（ ） 成品（LCM） TRAY 盤 (2) WF43GTIBEDBT0# BP01 內盒(3)Product Box 內盒 PK3R1XXXXXXXXXXX0001 泡棉(4)Foam 泡棉 外紙箱(5)Carton 外紙箱 ----PK4Q1XXXXXXXXXXX0000 NO. 1 2 3 4 5 6 Dimensions Quantity TBD TBD TBD TBD TBD TBD TBD TBD 332 x 280 x 100 283 x 230 x 8 565 x 340 x 320 7 8 9 2.單箱數量規格表 單箱數量規格表(Packaging Specifications and Quantity) : 單箱數量規格表 (1)LCM quantity per box : no per tray TBD x no of tray (2)Total LCM quantity in carton : quantity per box TBD x no of boxes 特 記 事 TBD = TBD = 項 (REMARK) 1. Label Specifications : MOOEL: LOT NO : QUANTITY: CHECK: 第 16 頁，共 20 頁 TBD TBD 第 17 頁，共 20 頁 15. Initial Code For Reference TBD 第 18 頁，共 20 頁 winstar LCM Sample Estimate Feedback Sheet Module Number： ： 1、Panel Specification： □ Pass □ NG , 1. Panel Type： 2. View Direction： □ Pass □ NG , 3. Numbers of Dots： □ Pass □ NG , 4. View Area： □ Pass □ NG , 5. Active Area： □ Pass □ NG , 6. Operating Temperature： □ Pass □ NG , 7. Storage Temperature： □ Pass □ NG , 1. PCB Size： □ Pass □ NG , 2. Frame Size： □ Pass □ NG , 3. Material of Frame： □ Pass □ NG , 4. Connector Position： □ Pass □ NG , 5. Fix Hole Position： □ Pass □ NG , 6. Backlight Position： □ Pass □ NG , 7. Thickness of PCB： □ Pass □ NG , 8. Height of Frame to PCB： □ Pass □ NG , 9. Height of Module： □ Pass □ NG , 10. Others： □ Pass □ NG , 1. Pitch of Connector： □ Pass □ NG , 2. Hole size of Connector： □ Pass □ NG , 3. Mounting Hole size： □ Pass □ NG , 4. Mounting Hole Type： □ Pass □ NG , 5. Others： □ Pass □ NG , 1. B/L Type： □ Pass □ NG , 2. B/L Color： □ Pass □ NG , Page: 1 8. Others： 2、Mechanical Specification： 3、Relative Hole Size： ： 4、Backlight Specification： 3. B/L Driving Voltage (Reference for LED Type)： □ Pass 4. B/L Driving Current： □ Pass □ NG , 5. Brightness of B/L： □ Pass □ NG , 6. B/L Solder Method： □ Pass □ NG , 7. Others： □ Pass □ NG , ＞＞ Go to page 2 ＜＜ 第 19 頁，共 20 頁 □ NG , winstar Module Number： Page: 2 5、Electronic Characteristics of Module： 1. Input Voltage： □ Pass □ NG , 2. Supply Current： □ Pass □ NG , 3. Driving Voltage for LCD： □ Pass □ NG , 4. Contrast for LCD： □ Pass □ NG , 5. B/L Driving Method： □ Pass □ NG , 6. Negative Voltage Output： □ Pass □ NG , 7. Interface Function： □ Pass □ NG , 8. LCD Uniformity： □ Pass □ NG , 9. ESD test： □ Pass □ NG , □ Pass □ NG , 10. Others： 6、Summary： ： Sales signature： Customer Signature： ： Date： ： 第 20 頁，共 20 頁 / /