Wiadvisor Access Point Mounting Instructions

Transcript

wiADVISOR Access Point Mounting Instructions 1. Dealer is responsible for the installation of a Cat5e network cable running from the wiTECH Access Gateway (WAG) to the wiADVISOR Access Point mounting location specified by the wiADVISOR Support Team. This cable should not exceed 328 feet; if a shorter cable is not available, please contact the wiADVISOR Support Team for further instructions. The wiADVISOR Access point is a power-over-Ethernet (POE) device, therefore a power outlet will not be needed at the mounting location. 2. Unpack the wiADVISOR Access Point installation kit. wiADVISOR Kit Includes:             1 - PicoStation M2HP (Access Point) 1 - Antenna 1 - Wall Mount Bracket 2 - Mounting Screws in Clear Bag 1 - 12” Zip-Tie for Pole Mount 3 - 4” Zip-Ties for cable management 1 - 2” Velcro Strip 1 - 12” Cat5e Cable 3 - Lanyard Bands 1 - microPod II 1 - USB Cable 1 - microPod Lanyard 3. Remove the black protective rubber boot from the wiADVISOR Access Point and screw on the antenna until snug. Warning: Do not over-tighten! 4. Mount the wiADVISOR Access Point in the location recommended by the wiADVISOR Support Team. The wiADVISOR Access Point should be mounted vertically with the BOTTOM no less than 7 ft. and no more than 9 ft. above the finished floor (ideally 8 ft. from floor). Use appropriate anchors for the substrate that you are fastening to (concrete, drywall, or wood). Version 2.1 5/12/15 Page 1 of 4 Revision Date: 5. The wiADVISOR Access Point can be mounted to a wall with the optional wall mount bracket, or to a pole using the molded mount and supplied zip-tie. If using the pole mount skip to step 5b for mounting instructions. a. Wall Mount: Position the wiADVISOR Access Point wall mount 7–9 ft. above the floor. Verify that the oval screw hole is on the bottom. (Refer to picture at right.) Mark screw holes and secure to wall with appropriate fasteners. IMPORTANT! Use a level to ensure the wall mount is straight up and down from floor to ceiling. Making a mistake here could mean wasted time repositioning the bracket assembly. Oval hole on bottom b. Pole Mount: There is a built-in pole mount on the back of the wiADVISOR Access Point. 1. Position the wiADVISOR Access Point 7–9 ft. above the floor on a vertical & level pole. 2. Feed the supplied 12” zip-tie through the slotted hole and secure to pole (refer to picture at right). 6. Slide bottom cover off of the wiADVISOR Access Point. Connect Ethernet cable (less than 328 ft. in length) to the RJ45 connector. Verify that the cable is secured in the connector and slide the cover back on. IMPORTANT! Some molded cables with snag-less boots are too big for the compartment and will interfere with a proper connection. The cable boot must not exceed 1 ¼”. Correct Incorrect 7. Wall mount only: Slide the wiADVISOR Access Point onto the wall mount in a downward motion and lock in place. Version 2.1 5/12/15 Page 2 of 4 Revision Date: Proceed With the Following Steps to Connect Your Equipment: Port 0/0 1. Using the included 12” Ethernet cable, connect port 0/0 on the WAG to the LAN 8 port on the 8-port power injector (as depicted by the yellow cable in the picture). The 8-port power injector is located just below the wiTECH Access Gateway. POE 8 2. Connect the wiADVISOR Access Point to the POE 8 port on the 8-port power injector using the Ethernet cable you used in Step 6 above. LAN 8 3. With the wiADVISOR Access Point plugged into port POE 8, and the wiTECH Diagnostic Extender plugged into port POE 1, your system should now look like the picture on the right. wiADVISOR wiTECH Diagnostic Extender Version 2.1 5/12/15 Page 3 of 4 Revision Date: Second LED 4. Once the Ethernet cables are plugged in properly, the first LED on the wiADVISOR Access Point will be solid green, and the second LED will be flashing green (as shown in the picture on the right). First LED Version 2.1 5/12/15 Page 4 of 4 Revision Date: