Transcript
Windows Vista Start Here (See the Reverse Side for Windows XP Installation)
3. Please wait for the installation process to complete.
5. Now, plug in your HWDN2 adapter. Windows Vista should
8. If prompted, you must enter
automatically begin detecting for updated drivers. Once Vista states it
a security key or passphrase
has completed installing drivers, move on to Step 6.
to enter the network. This
Important: Do not connect the USB adapter until you
passphrase is defined by your
install the driver from the CD and are instructed to do so. Otherwise, the USB adapter may not operate correctly.
1.
Insert the Setup CD and a menu page will automatically appear on your screen. Select “Driver & Utility Setup”.
current wireless network settings.
Hi-GainTM Wireless-150N Network USB Dish Adapter
9. Select your connection preferences once connected
4. After the installation is
HWDN2
and close the utility window
complete, exit the wizard by clicking on the Finish button.
6.
After installing all drivers and utilities, right click on the Start
menu and select “Connect To”.
when finished. The utility setup is complete and you may now begin enjoying your wireless network!
2. Select “Install”
(a)Your system tray (bottom right corner) will indicate that the driver is installing. (b) It will indicate “Device driver software installed sucessfully” when it is done.
Installation is complete! Refer to the Manual for Advanced Configuration
Place the Adapter in an open space where it can easily receive a wireless signal.
(a) (b)
7.
Double click on the
desired network or select and press Connect. Please wait as it connects.
SUPPORT Email:
[email protected] Website: www.hawkingtech.com/support 24-Hour Technical Support 888-202-3344 (Toll Free US & Canada) 949-790-0810 (International)
www.hawkingtech.com RMA Information http://www.hawkingtech.com/rma.php Sales Information
[email protected]
Hawking is a registered trademark or Hawking Technologies, Inc. ©2008 Hawking Technologies, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective owners.
QIG_HWDN2.indd 1
Package Contents Wireless-150N Network USB Dish Adapter USB Extension Cable CD (Setup Drivers and User’s Manual)
QUICK INSTALLATION GUIDE 4/8/2008 3:14:05 PM
Windows XP Start Here (See the Reverse Side for Windows Vista Installation)
3.
On the next page, click install when prompted to do so and wait a while as the installation process takes places
6.
Plug in your HWDN2 adapter at this time.
Important: Do not connect the USB adapter until you install the driver from the CD and are instructed to do so. Otherwise, the USB adapter may not operate correctly.
1.
Insert the Setup CD and a menu page will automatically appear on your screen. Select “Driver & Utility Setup”.
Important: This Quick Installation Guide is intended for quick setup with available wireless networks. If you need to connect to a specific network that is not listed and need to manually set up the IP Address, please refer to the manual on the CD.
4. 2.
7.
After restarting your PC, locate the Hawking icon in the system tray, right click on it and then choose Launch Configuration.
5.
Restart your computer if the wizard prompted you to do so. Otherwise, please plug the Hawking HWDN2 Wireless Dish Adapter into an available USB port on your desktop or notebook. Otherwise, continue on to Step 6.
QIG_HWDN2.indd 2
If your network is WPA enabled: a. Encryption Type: Select TKIP or AES b. All Encryption must match the selected network’s encryption settings. c. Pre-shared Key: Should be 8-63 characters and must match your network.
When the utility opens up, select the tab labeled Network. Click the Rescan button to get the updated wireless networks in your area, and then double click on the desired network. Note: If you are connecting to a network without encryption (Encryption: None), continue to Step 10.
If your network is WPA2 enabled: a. Enter Pre-shared Key (should be 8-63 characters and must match your network). After you are done entering the selected Network Encryption, click OK and proceed.
If you are connecting to a secured network (network with encryption: TKIP, WPA, WEP, etc.), please go to Step 9.
10.
9.
Select the Authentication Type. If you do not have this information, please request it from your network administrator or from the person who set up your network.
The Wizard has sucessfully installed the HWDN2. Select Finish.
Select the HWDN2 Configuration Tool and then click Next.
8.
If your network is WEP enabled: a. Select 64-bit or 128-bit b. passphrase - this is case sensitive, no more than 16 alphanumeric characters, and must be the same as your network. c. 64-bit WEP key: exactly 10 hexadecimal characters and must be the same as your network. 128-bit WEP key: exactly 26 hexadecimal characters and must be the same as your network.
Once you are connected to the network, click on the arrow button in the lower right-hand corner to view the performance aspects of your Wireless Adapter: transmit rate, link/signal quality, wireless channel, etc. Make any adjustments to the position of the HWDN2 to maximize performance. For best results, please direct the HWDN2 towards the wireless access point from which you wish to receive a wireless network signal. You have completed the configuration for the Hi-Gain Wireless-N Dish Adapter.
NOTE: If you are using ASCII, please select ASCII from the drop down menu.
4/8/2008 3:14:08 PM
