Transcript
Winstar Display Co., LTD
華凌光電股份有限公司 住址: 407 台中市中清路 163 號 No.163 Chung Ching RD., Taichune, Taiwan, R.O.C
WEB: http://www.winstar.com.tw E-mail:
[email protected] Tel:886-4-24262208 Fax：886-4-24262207
SPECIFICATION CUSTOMER : MODULE NO.:
WF43GTIBEDBN0#
APPROVED BY: ( FOR CUSTOMER USE ONLY ) PCB VERSION:
SALES BY
APPROVED BY
CHECKED BY
DATA:
PREPARED BY
叶慧芬
ISSUED DATE:
2013-2-19
第 1 頁，共 20 頁
Winstar Display Co., LTD MODLE NO：
華凌光電股份有限公司 DOC. FIRST ISSUE
RECORDS OF REVISION
VERSION
DATE
0
2013.2.19
REVISED PAGE NO. SUMMARY
First issue
第 2 頁，共 20 頁
Contents 1. Module Classification Information 2. Summry 3. General Specification 4. Absolute Maximum Ratings 5. Electrical Characteristics 6. DC Characteristics 7. Interface Timing 8. Optical Characteristics 9. Interface 10. Block Diagram 11. Reliability 12. Contour Drawing 13. Package specification 14. Initial Code For Reference
第 3 頁，共 20 頁
1.Module Classification Information
W
F
43
G
T
I
B
E
D
B
N
0
1 ○
2 ○
3 ○
4 ○
5 ○
6 ○
7 ○
8 ○
9 ○
10 ○
11 ○
12 ○
# 13 ○
Brand：WINSTAR DISPLAY CORPORATION Display Type：H→Character Type, G→Graphic Type F→TFT Type Display Size：4.3 ” TFT Model serials no. Backlight Type： F→CCFL, White T→LED, White
LCD Polarize I→Transmissive, W. T, 6:00 Type/ Temperature L→Transmissive, W.T,12:00 range/ Gray Scale Inversion Direction A：TFT LCD B：TFT+FR+CONTROL BOARD C：TFT+FR+A/D BOARD D：TFT+FR+A/D BOARD+CONTROL BOARD E：TFT+FR+POWER BOARD F：TFT+CONTROL BOARD Solution: A: 128160 B:320234 C:320240 D:480234 H:1024600 I:320480 J:240320 K:800600 L：LVDS 9 D: Digital ○ N：without control board A：8Bit 10 Interface： ○
G：TFT+FR H：TFT+D/V BOARD I：TFT+FR+D/V BOARD J：TFT+POWER BD
E:480272 L:240400
F: 640480 G: 800480 M :1024768
B：16Bit
11 TS： ○ N：Without TS T：resistive touch panel C：capacitive touch panel 12 Version ○ 13 Special Code #:Fit in with ROHS directive regulations ○
第 4 頁，共 20 頁
2.SUMMARY This technical specification applies to 4.3’ color TFT-LCD panel. The 4.3’ color TFT-LCD panel is designed for camcorder, digital camera application and other electronic products which require high quality flat panel displays. This module follows RoHS.
3.General Specification Item
Dimension
Unit
480 x RGBx272(TFT)
dots
106.7 x 83.98 x 7.1
mm
Active area
95.04 x 53.86
mm
Dot pitch
0.066 x 0.198
mm
Dot Matrix Module dimension
LCD type
TFT, Negative, Transmissive
View Direction Gray Scale Inversion Direction Backlight Type
12 o’clock 6 o’clock LED,Normally White
*Color tone slight changed by temperature and driving voltage.
4.Absolute Maximum Ratings Item
Symbol
Min
Typ
Max
Unit
Operating Temperature
TOP
-20
－
+70
℃
Storage Temperature
TST
-30
－
+80
℃
Note: Device is subject to be damaged permanently if stresses beyond those absolute maximum ratings listed above 1. Temp. ≦600C, 90% RH MAX. Temp. ＞ 600C , Absolute humidity shall be less than 90% RH at 600C
第 5 頁，共 20 頁
5.Electrical Characteristics 5.1. Operating conditions:
Item
Symbol
Condition
Min
Typ
Max
Unit
VCC
－
3.1
3.3
3.5
V
Supply Voltage For Logic
5.2 LED driving conditions Parameter LED current Power Consumption LED voltage LED Life Time
Symbol Min. VBL+
30 -
Typ. 20 640 32 50,000
Max. 680 34 -
Unit mA mW V Hr
Note 1 : There are 1 Groups LED
K
A Note 2 : Ta = 25 ℃ Note 3 : Brightess to be decreased to 50% of the initial value Note 4 : The single LED lamp case
6. DC Characteristics
第 6 頁，共 20 頁
Remark
Note 1 Note 2,3,4
7. Interface Timing 7.1.1 8080 Mode The 8080 mode MCU interface consist of CS#, D/C#, RD#, WR#, D[23:0] and TE signals (Please refer to Table 6-1 for pin multiplexed with 6800 mode). This interface use WR# to define a write cycle and RD# for read cycle. If the WR# goes low when the CS# signal is low, the data or command will be latched into the system at the rising edge of WR#. Similarly, the read cycle will start when RD# goes low and end at the rising edge of RD#.
7.1.2 8080 Mode Write Cycle
第 7 頁，共 20 頁
7.1.3 Pixel Data Format
第 8 頁，共 20 頁
8. Optical Characteristics Item
Symbol Condition. Min Typ. Max. Tr 10 20 Response time θ=0°、Φ=0° 15 30 Tf At optimized Contrast ratio CR 400 500 viewing angle Wx 0.24 0.29 0.34 Color Chromaticity White θ=0°、Φ=0 Wy 0.26 0.31 0.36 60 70 ΘR Hor. 60 70 ΘL Viewing angle CR≧10 40 50 ΦT Ver. 60 70 ΦB Brightness
-
-
350
-
500
Unit .ms .ms
Remark
-
Note 4
Note 3
Note 2,5
Deg.
cd/m 2
Note 1 Center of display
Ta=25±2℃, IL=20mA Note 1: Definition of viewing angle range
Fig. 8-1 Definition of viewing angle Note 2: Test equipment setup: After stabilizing and leaving the panel alone at a driven temperature for 10 minutes, the measurement should be executed. Measurement should be executed in a stable, windless, and dark room. Optical specifications are measured by Topcon BM-7 luminance meter 1.0° field of view at a distance of 50cm and normal direction.
第 9 頁，共 20 頁
Fig. 8-2 Optical measurement system setup Note 3: Definition of Response time: The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time, Tr, is the time between photo detector output intensity changed from 90%to 10%. And fall time, Tf, is the time between photo detector output intensity changed from 10%to 90%
Note 4: Definition of contrast ratio: The contrast ratio is defined as the following expression.
Note 5: Definition of color chromaticity (CIE1931) Color coordinates measured at center point of LCD. Note 6: All input terminals LCD panel must be ground while measuring the center area of the panel.
第 10 頁，共 20 頁
9. Interface 9.1. LCM PIN Definition
Pin
Symbol
I/O
Function
1
GND
P
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
VDD BL E RS WR RD D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 NC NC CS RST NC NC NC NC NC DIP ON
P I I I I I I I I I I I I I I I I I I I I I I -
Systen ground pin of the IC. Connect to systen ground. Power Supply : +3.3V Backlight control signal , H: On \ L:Off Data/Command select Write strobe signal Read strobe signal Data bus Data bus Data bus Data bus Data bus Data bus Data bus Data bus Data Data Data Data Data Data Data Data No connection No connection Chip select Hardware reset No connection No connection No connection No connection No connection Display control H: On \ L:Off
Remark
第 11 頁，共 20 頁
10. BLOCK DIAGRAM
BL
TFT LCD 480xR G B x272
RESET
LED+
LED-
Y2
X2
Y1
X1
B7~B0
G7~G0
R7~R0
DE
DCLK
DISP
HSYNC
VSYNC
VSS
第 12 頁，共 20 頁
DB15
DB0
RESET
BL_E
RS
DIS_ON
RD
WR
CS
GND
L C D control board & B ack ligh t control VDD
VCC
F P C inferface
11.Reliability Content of Reliability Test (Wide temperature, -20℃~70℃ ℃) Environmental Test Test Item
Content of Test
High Temperature storage
Endurance test applying the high storage temperature for a long 80℃ time. 200hrs Endurance test applying the high storage temperature for a long -30℃ time. 200hrs Endurance test applying the electric stress (Voltage & Current) 70℃ and the thermal stress to the element for a long time. 200hrs Endurance test applying the electric stress under low temperature -20℃ for a long time. 200hrs The module should be allowed to stand at 60℃,90%RH max 60℃,90%RH For 96hrs under no-load condition excluding the polarizer, 96hrs Then taking it out and drying it at normal temperature. The sample should be allowed stand the following 10 cycles of -20℃/70℃ operation 10 cycles -20℃ 25℃ 70℃
Low Temperature storage High Temperature Operation Low Temperature Operation High Temperature/ Humidity Operation Thermal shock resistance
Test Condition
Note 2 1,2 —— 1 1,2
——
30min
Vibration test
Static electricity test
5min 30min 1 cycle Endurance test applying the vibration during transportation and Total fixed amplitude : 3 using. 15mm Vibration Frequency : 10~55Hz One cycle 60 seconds to 3 directions of X,Y,Z for Each 15 minutes Endurance test applying the electric stress to the terminal. —— VS=800V,RS=1.5kΩ CS=100pF 1 time
Note1: No dew condensation to be observed. Note2: The function test shall be conducted after 4 hours storage at the normal Temperature and humidity after remove from the test chamber. Note3: Vibration test will be conducted to the product itself without putting it in a container.
第 13 頁，共 20 頁
12.Contour Drawing PI N 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
DESC GND VDD BL E RS WR RD D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 NC NC CS RST NC NC NC NC NC DI P ON
480 RGB X 272
4-? 3.5 PTH
K
A
CIRCUIT DIAGRAM (10 揹 ㄘ
RGB SCALE 1:100
1
2
3
4
5
6
7
8
9
The non-specified tolerance of dimension is
第 14 頁，共 20 頁
0.3mm.
13. Package specification LCM Model
WF43GTIBEDBN0#
Drawing NO.
LCM 包裝規格書
Approve
Check
Contact
LCM Packaging Specifications
DATE 12'11/15
初版 12'11/15
版次 Ver
0
1.包裝材料規格表 包裝材料規格表（ ）:(per carton) 包裝材料規格表（Packaging Material） Item
NO.
1 2 3 4 5 6
Model
Dimensions
Quantity TBD TBD TBD TBD TBD
成品（ ） 成品（LCM） TRAY 盤 (2)
WF43GTIBEDBN0# PKCA1XXXXXXXXXXX0233
106.7 x 69.9 x 7.1
BP01 內盒(3)Product Box 內盒
PK3R1XXXXXXXXXXX0001
泡棉(4)Foam 泡棉 外紙箱(5)Carton 外紙箱
----PK4Q1XXXXXXXXXXX0000
332 x 280 x 100 283 x 230 x 8 565 x 340 x 320
TBD
7 8 9 2.單箱數量規格表 單箱數量規格表(Packaging Specifications and Quantity) : 單箱數量規格表 (1)LCM quantity per box : no per tray TBD x no of tray (2)Total LCM quantity in carton : quantity per box TBD x no of boxes
特
記
事
TBD = TBD =
項 (REMARK)
1. Label Specifications : MOOEL: LOT NO : QUANTITY: CHECK:
第 15 頁，共 20 頁
TBD TBD
第 16 頁，共 20 頁
14. Initial Code For Reference void Initial_code() { Write_Command(0x01); Delay_ms(10); Write_Command(0xe0); Write_Parameter(0x01); Delay_ms(5); Write_Command(0xe0); Write_Parameter(0x03); Delay_ms(5); Write_Command(0xb0); Write_Parameter(0x08); Write_Parameter(0x80); Write_Parameter(0x01); Write_Parameter(0xdf); Write_Parameter(0x01); Write_Parameter(0x0f); Write_Parameter(0x00); Write_Command(0xf0); Write_Parameter(0x00); Write_Command(0x3a); Write_Parameter(0x50);//0x50 is for 5-6-5 color mode;0x60 is for 6-6-6 color mode //Set the MN of PLL Write_Command(0xe2); Write_Parameter(0x1d); Write_Parameter(0x02); Write_Parameter(0x54); Write_Command(0xe6); Write_Parameter(0x01); Write_Parameter(0x55); Write_Parameter(0xff);
//Set front porch and back porch Write_Command(0xb4); Write_Parameter(0x02); Write_Parameter(0x09); Write_Parameter(0x00); Write_Parameter(0x28); Write_Parameter(0x07); Write_Parameter(0x00); Write_Parameter(0x00); Write_Parameter(0x00); Write_Command(0xb6); Write_Parameter(0x01); Write_Parameter(0x19); 第 17 頁，共 20 頁
Write_Parameter(0x00); Write_Parameter(0x08); Write_Parameter(0x01); Write_Parameter(0x00); Write_Parameter(0x00); Write_Command(0x2a); Write_Parameter(0x00); Write_Parameter(0x00); Write_Parameter(0x01); Write_Parameter(0xdf); Write_Command(0x2b); Write_Parameter(0x00); Write_Parameter(0x00); Write_Parameter(0x01); Write_Parameter(0x0f); Write_Command(0x29); Write_Command(0x2c); }
第 18 頁，共 20 頁
winstar LCM Sample Estimate Feedback Sheet Module Number： ： 1、Panel Specification： □ Pass □ NG , 1. Panel Type： 2. View Direction：
□ Pass
□ NG ,
3. Numbers of Dots：
□ Pass
□ NG ,
4. View Area：
□ Pass
□ NG ,
5. Active Area：
□ Pass
□ NG ,
6. Operating Temperature：
□ Pass
□ NG ,
7. Storage Temperature：
□ Pass
□ NG ,
1. PCB Size：
□ Pass
□ NG ,
2. Frame Size：
□ Pass
□ NG ,
3. Material of Frame：
□ Pass
□ NG ,
4. Connector Position：
□ Pass
□ NG ,
5. Fix Hole Position：
□ Pass
□ NG ,
6. Backlight Position：
□ Pass
□ NG ,
7. Thickness of PCB：
□ Pass
□ NG ,
8. Height of Frame to PCB： □ Pass
□ NG ,
9. Height of Module：
□ Pass
□ NG ,
10. Others：
□ Pass
□ NG ,
1. Pitch of Connector：
□ Pass
□ NG ,
2. Hole size of Connector：
□ Pass
□ NG ,
3. Mounting Hole size：
□ Pass
□ NG ,
4. Mounting Hole Type：
□ Pass
□ NG ,
5. Others：
□ Pass
□ NG ,
1. B/L Type：
□ Pass
□ NG ,
2. B/L Color：
□ Pass
□ NG ,
Page: 1
8. Others：
2、Mechanical Specification：
3、Relative Hole Size： ：
4、Backlight Specification：
3. B/L Driving Voltage (Reference for LED Type)： □ Pass 4. B/L Driving Current：
□ Pass
□ NG ,
5. Brightness of B/L：
□ Pass
□ NG ,
6. B/L Solder Method：
□ Pass
□ NG ,
7. Others：
□ Pass
□ NG ,
＞＞ Go to page 2 ＜＜
第 19 頁，共 20 頁
□ NG ,
winstar Module Number：
Page: 2
5、Electronic Characteristics of Module： 1. Input Voltage：
□ Pass
□ NG ,
2. Supply Current：
□ Pass
□ NG ,
3. Driving Voltage for LCD：
□ Pass
□ NG ,
4. Contrast for LCD：
□ Pass
□ NG ,
5. B/L Driving Method：
□ Pass
□ NG ,
6. Negative Voltage Output：
□ Pass
□ NG ,
7. Interface Function：
□ Pass
□ NG ,
8. LCD Uniformity：
□ Pass
□ NG ,
9. ESD test：
□ Pass
□ NG ,
□ Pass
□ NG ,
10. Others：
6、Summary：
Sales signature： ： Customer Signature： ：
Date： ：
第 20 頁，共 20 頁
/
/
