Transcript
Wintec Slim SATA Drive JM608 Series W2ESxxxG1TA-J71xx
INFORMATION IN THIS DOCUMENT IS PROVIDED IN RELATION TO WINTEC INDUSTRIES PRODUCTS, AND IS SUBJECT TO CHANGE WITHOUT NOTICE. NOTHING IN THIS DOCUMENT SHALL BE CONSTRUED AS GRANTING ANY LICENSE, EXPRESS OR IMPLIED. ALL INFORMATION IN THIS DOCUMENT IS PROVIDED ON AN “AS-IS” BASIS WITHOUT GUARANTEE OR WARRANTY OF ANY KIND. Please contact your nearest Wintec representative for the latest updates or additional product information.
Datasheet Wintec Slim SATA Drive W2ESxxxG1TA-J71xx Version 1.0
6/30/2014 www.wintecind.com Page 1
Product Introduction Wintec Slim SATA Drive JM608 Series W2ESxxxG1TA-J71xx The Wintec Industries W2ESxxxG1TA(I)-J71xx series of ROHS Compliant Slim SATA Drives are constructed with MLC NAND-type flash memory devices paired to JMicron 608 SATA III NAND Flash controller for virtual-to- physical address mapping and other sophisticated flash management functions. The Wintec Flash Solid State Disk (SSD) provides major advantages over the traditional magnetic hard disk drive (HDD). Faster access time and transfer rate, silent operation and low power consumption, better shock and vibration resistance, and lower total cost of ownership make the Wintec SSDs an attractive choice as the next generation mass storage device. The Wintec JM608 series Slim SATA provides high-speed data transfer and reliability utilizing MLC NAND-flash in storage capacities ranging up to 128GB, in JEDEC MO-297A form factor. Its robust design enables the SSD to achieve outstanding reliability and performance. The JMF608 controller implements bad block management and dynamic/static wear-leveling techniques to ensure that the NAND flash memory is not worn out prematurely. The controller utilizes up to 40 bits/1K byte sector BCH ECC algorithms for error correction. The drive supports basic SMART features to monitor the drive status. The Wintec JM608 series Slim SATA drives are ideal for portable and desktop computers, point of sale (POS), handheld device, gaming machine, network equipment, notebook, thin-client and set-top boxes (STB).
General Features Density up to 128GB SATA-III interface and backwards compatible High-Performance MLC NAND Flash memory
Reliability Enhanced endurance by dynamic/static wear Leveling Bad Block Management ECC Engine: Utilizes 8/16/24/40 bit correctable per 1KB BCH ECC Data Integrity under power cycling Support Shift read feature of NAND flash when ECC fail MTTF: 1,000,000 operating hours I-Temp Available
Performance High Performance 300MB/s Seq. Read (SATA-III) High Performance 200MB/s Seq. Write (SATA-III) Random Read: 15,000 IOPS at 4KB transfer (SATA- III)
Compatibility
Serial ATA Revision 3.1 Compliant ATA/ATAPI-8 Compliant Supports S.M.A.R.T RoHS compliant
NOTE: 1. See Section 5.0 for Configuration & Ordering Guide
Datasheet Wintec Slim SATA Drive W2ESxxxG1TA-J71xx Version 1.0
6/30/2014 www.wintecind.com Page 2
Revision History Revision
Month
Year
History
0.99 1.0
March
2014 2014
Preliminary Release
June
Added 50GB capacity
Datasheet Wintec Slim SATA Drive W2ESxxxG1TA-J71xx Version 1.0
6/30/2014 www.wintecind.com Page 3
Table of Contents 1.0
2.0
3.0
4.0 5.0
General Product Specifications
5
1.1 1 .1 1.2 1 .
Block Diagram
6
Architecture
6
EElectrical Specifications
2 l 2.1 2 e .2 2.2 1 .
7
General
7
SATA P in Assignment and Description
7
Software Interface
8
2 3.1
ATA Command Set
8
3.2
ATA Command Description: IDENTIFY DEVICE (ECh)
9
3.3
ATA Command Description: SET FEATURES (EFh)
14
3.4
SMART Command Support
14
Physical Dimensions Product Guide & Ordering Information
Datasheet Wintec Slim SATA Drive W2ESxxxG1TA-J71xx Version 1.0
16 17
6/30/2014 www.wintecind.com Page 4
1.0 General Product Specifications For all the following specifications, values are defined at ambient temperature unless otherwise stated.
Table 1: User Capacity Specifications 2,3 Model Number¹ (typ) NAND Flash Type W2ES004G1TA(I)-J71xx-yyy.zz W2ES008G1TA(I)-J71xx-yyy.zz W2ES016G1TA(I)-J71xx-yyy.zz W2ES032G1TA(I)-J71xx-yyy.zz W2ES050G1TA(I)-J71xx-yyy.zz W2ES064G1TA(I)-J71xx-yyy.zz W2ES128G1TA(I)-J71xx-yyy.zz
MLC MLC MLC MLC MLC MLC MLC
Total Capacity
User Capacity
Over-provision
4GB 8GB 16GB 32GB 64GB 64GB 128GB
3.5G B 7.5G B 15GB 30GB 50GB 60GB 120GB
7% 7% 7% 7% 28% 7% 7%
Note: 1. See Section 5.0 for Configuration & Ordering Guide 2. 1GB = 1,000,000,000 Bytes 3. Capacity available to end-user is less than “Total Capacity” due to flash controller overhead, and may vary with flash configuration.
Table 2: Typical Performance Specifications
Parameter
Typical Performance4
Sustained Sequential Read Sustained Sequential Write Sustained IOPS Random Read
up to 300MB/sec up to 200MB/sec up to 15,000 IOPS
Note: 4. Bandwidth measured on high-performance desktop system. Note that performance may also vary depending on host system, drive capacity, and drive configuration. Measured at QD=32.
Table 3: Flash Endurance
Parameter
Spec
Program/Erase Cycles Data Retention MTTF
Up to 3,000 cycles 5 Years (Min.) 1,000,000 Hours
Table 4: SSD Data Reliability
Parameter
Spec
Non-Recoverable Errors Raw ECC Correctability
< 1 in 10 Bytes Read Up to 40 bits / 1K Bytes data
16
Table 5: Environmental Specifications
Parameter Temperature
Commercial Temp. Industrial Temp.
Humidity (Non-Condensing) Vibration Shock (Operating) Noise
Datasheet Wintec Slim SATA Drive W2ESxxxG1TA-J71xx Version 1.0
Operating
Non-Operating
0C to 70C -40C to 85C 5% to 95% 20 G RMS 1,500 G (Max.) 0 dB
-55C to 95C -55C to 95C 5% to 95% N/A 0 dB
6/30/2014 www.wintecind.com Page 5
1.1 Block Diagram
Flash Controller 1 & ECC Engine
SATA Controller BUS SATA III I/F
Channel 1
MLC NAND FLASH
Channel 2
MLC NAND FLASH
Channel 3
MLC NAND FLASH
Channel 4
MLC NAND FLASH
SATA 6G PHY
CPU
Flash Controller 4 & ECC Engine
Figure 1: Block Diagram 1.2 Architecture The Wintec J7 series SSD utilizes a single flash controller chip with 4 parallel channels of flash memory interface. The flash controller also simultaneously manages the file read and write interface with the host system via a single SATA-III interface. By utilizing 4 parallel channels of MLC flash memory, the Slim SATA SSD can provide both high performance and reliability, while maintaining a minimal unit cost.
Datasheet Wintec Slim SATA Drive W2ESxxxG1TA-J71xx Version 1.0
6/30/2014 www.wintecind.com Page 6
2.0 Electrical Specification 2.1 General Table 6: Absolute Maximum Ratings Symbol Parameter
Min
Max
Units
Vcc
-0.5
3.96
V
Vcc With Respect to GND
Table 7: Typical Operating Conditions (VCC=3.3V 10%) Symbol Parameter
Min
Typical
Max
Units
Vcc
3.0
3.3
3.6
V
0
70
C
-40 5
85 95
C %
Vcc With Respect to GND Operating Temperature (Commercial Temp) Industrial Temp Humidity
TA H
Table 8: Power Consumption Symbol Parameter
Value
Units
Pi PT Pmax
0.35 0.70 1.25
Watts Watts Watts
Idle Power consumption Typical operating power consumption Maximum operating power consumption
2.2 SATA Pin Assignment and Description The SATA connectors are compliant with standard SATA power specifications. As is standard, power may be supplied to all of th e power pins. However, only the 5V power pins are utilized to provide power to the SSD. Therefore, where non -standard power supplies and connections are utilized, the power supply does not need to supply the SSD with power to the 3.3V or 12V power pins.
Table 9: SATA connector specification compliant No. Plug Connector Pin Definition
Signal
S1 S2 S3 S4 S5 S6 S7
GND A+ AGND BB+ GND
Ground Differential signal A Ground Differential signal B Ground
Key and spacing separate signal and power segments
Power
P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15
V33 V33 V33 GND GND GND V5 V5 V5 GND DAS/DSS GND V12 V12 V12
Datasheet Wintec Slim SATA Drive W2ESxxxG1TA-J71xx Version 1.0
3.3V power (Not Used) 3.3V power (Not Used) 3.3V power, pre-charge (Not Used) Ground Ground Ground 5V power, pre-charge 5V power 5V power Ground Device Present Ground 12V power, pre-charge (Not Used) 12V power (Not Used) 12V power (Not Used)
6/30/2014 www.wintecind.com Page 7
3.0 Software Interface 3.1 ATA Command Set All mandatory, and many optional commands and features are supported. The following tables summarize the ATA feature set and commands.
Table 10: ATA Command Feature Set CHECK POWER MODE EXECUTE DIAGNOSTICS FLUSH CACHE IDENTIFY DEVICE IDLE IDLE IMMEDIATE INITIALIZE DEVICE PARAMETERS READ DMA READ DMA EXT READ FPDMA QUEUED READ LOG DMA EXT READ LOG EXT READ MULTIPLE READ SECTOR(S) READ VERIFY SECTOR(S) RECALIBRATE SECURITY DISABLE PASSWORD SECURITY ERASE PREPARE SECURITY ERASE UNIT SECURITY FREEZE LOCK SECURITY SET PASSWORD SECURITY UNLOCK SEEK SET FEATURES SET MULTIPLE MODE SLEEP SMART STANDBY STANDBY IMMEDIATE WRITE DMA WRITE DMA EXT WRITE FPDMA QUEUED WRITE LOG DMA EXT WRITE LOG EXT WRITE MULTIPLE WRITE SECTOR(S)
Datasheet Wintec Slim SATA Drive W2ESxxxG1TA-J71xx Version 1.0
Code E5h 90h E7h ECh E3h E1h 91h C8h 25h 60h 47h 2Fh C4h 20h or 21h 40h or 41h 10h F6h F3h F4h F5h F1h F2h 7xh EFh C6h E6h B0h E2h E0h CAh 35h 61h 57h 3Fh C5h 30h or 31h
SC X X X X O X O O O O O O O O O X X X X X X X X O O X X X X O O O O O O O
SN X X X X X X X O O O O O O O O X X X X X X X X X X X X X X O O O O O O O
Parameters Used CY DR X O X O X O X O X O X O X O O O O O O O O O O O O O O O O O X O X O X O X O X O X O X O O O X O X O X O O O X O X O O O O O O O O O O O O O O O
HD X X X X X X O O O O O O O O O X X X X X X X O X X X X X X O O O O O O O
FT X X X X X X X X X X X X X X X X X X X X X X X O X X O X X X X X X X X X
6/30/2014 www.wintecind.com Page 8
Note: O = Valid, X = Don’t care SC = Sector Count Register SN = Sector Number Register CY = Cylinder Low/High Register DR = Device Select Bit (Device/Head Register Bit 4) HD = Head Select bit (Device/Head Register Bit 3-0) FT = Features Register
3.2 ATA Command Description: IDENTIFY DEVICE (ECh) This commands read out of 512Bytes of drive parameter information. Parameter Information consists of the arrangement and value as shown in the following table. This command enables the host to receive the Identify Drive Information from the device.
Table 11: IDENTIFY Device (ECh) information default value Word
Value
F/V F X F X X F X F X V X X X V X F X X F F
Description General configuration bit-significant information 15 0 = ATA device 14-8 Retired 14-8 7 1Retired = removable device 6 Obsolete 7 1 = removable media device 5-3 Retired 6 Obsolete 2 Reserved 5-3 Retired 1 Retired 0 Reserved 2 Reserved Number of logical cylinders 1 Retired Specific configuration 0 Reserved Number of logical heads Retired Number of logical sector per logical track Reserved for assignment by the CompactFlash_Association Retired Obsolete Retired Obsolete Firmware revision (8 ASCII characters) Model number (40 ASCII characters)
0
0040h
1 2 3 4-5 6 7-8 9 10-19 20 -21 22 23-26 27-47
XXXXh C837h 00XXh XXXXh XXXXh XXXXh 000Eh XXXXh XXXXh 003Fh XXXXh XXXXh
47
8000h
F F F
15-8 7-0
48
4000h
F
Reserved Capabilities 15-14 Reserved for the IDENTIFY DEVICE command 13 1= Standby timer values as specified in this standard are supported 0= Standby timer values shall be managed by the device 12 Reserved for the IDENIFY PACKET DEVICE command 11 1 = IORDY supported 0 = IORDY may be supported 10 1 = IORDY may be disabled 9 1 = LBA supported 8 1 = DMA supported 7-0 Retired
F F
49
2F00h
F F F F F X
80h 00h = Reserved 01h = Maximum number of 1 sectors on READ/WRITE MULTIPLE commands
Datasheet Wintec Slim SATA Drive W2ESxxxG1TA-J71xx Version 1.0
6/30/2014 www.wintecind.com Page 9
Word
Value
54-58
XXXXh
X
Description Capabilities 15 Shall be cleared to zero 14 Shall be set to one 13-2 Reserved 1 Obsolete 0 Shall be set to one to indicate a device specific Standby timer value minimum Obsolete Capabilities 15-3 Reserved 2 1 = the fields reported in word 88 are valid 0 = the fields reported in word 88 are not valid 1 1 = the fields reported in words 70:64 are valid 0 = the fields reported in words 70:64 are not valid 0 1 = the fields reported in words 58:54 are valid 0 = the fields reported in words 58:54 are not valid Obsolete
59
0000h
F F V
15-9 8 7-0
60-61 62
XXXXh 0000h
F X F V
Total number of user addressable sectors Obsolete 15-11 Reserved 10 1 = Multiword DMA mode 2 is selected 0 = Multiword DMA mode 2 is not selected 9 1 = Multiword DMA mode 1 is selected 0 = Multiword DMA mode 1 is not selected 8 1 = Multiword DMA mode 0 is selected 0 = Multiword DMA mode 0 is not selected 7-3 Reserved 2 1 = Multiword DMA mode 2 and below are supported 1 1 = Multiword DMA mode 1 and below are supported 0 1 = Multiword DMA mode 0 is supported 15-8 Reserved 7-0 Advanced PIO modes supported Minimum Multiword DMA transfer cycle time per word Manufacturer’s recommended Multiword DMA transfer cycle time Minimum PIO transfer cycle time without flow control Minimum PIO transfer cycle time with IORDY flow control Reserved (for future command overlap and queuing) Queue depth 15-5 Reserved 4-0 Maximum queue depth - 1 Serial ATA Capabilities 15-13 Reserved for Serial ATA 12 1 = Supports NCQ priority information 11 1 = Supports Unload while NCQ commands are outstanding 10 1 = Supports the SATA Phy Event Counters log 9 1 = Supports receipt of host initiated power management requests 8 1 = Supports the NCQ feature set 7-4 Reserved for Serial ATA 3 1 = Supports SATA Gen3 Signaling Speed (6.0Gb/s) 2 1 = Supports SATA Gen2 Signaling Speed (3.0Gb/s) 1 1 = Supports SATA Gen1 Signaling Speed (1.5Gb/s) 0 Shall be cleared to zero
50
4000h
51-52
0000h
F/V F F F X F X F F
53
0007h
F X
V 63
0007h
64
0003h
65 66 67 68 69-74
0078h 0078h 0078h 0078h 0000h
75
0000h
V F F F F F F F F F F F F
F
76
Xh
Reserved 1 = Multiple sector setting is valid xxh = Setting for number of sectors that shall be transferred per interrupt on R/W Multiple command
Datasheet Wintec Slim SATA Drive W2ESxxxG1TA-J71xx Version 1.0
6/30/2014 www.wintecind.com Page 10
Word 77
78
79
Value
Description Reserved
Xh
Serial ATA features supported 15-7 Reserved for Serial ATA 6 1 = Device supports Software Settings Preservation 5 Reserved for Serial ATA 4 1 = Device supports in-order data delivery 3 1 = Device supports initiating power management 2 1 = Device supports DMA Setup auto-activation 1 1 = Device supports non-zero buffer offsets 0 Shall be cleared to zero
Xh
Serial ATA features enabled 15:7 Reserved for Serial ATA 6 1 = Software Settings Preservation enabled 5 Reserved for Serial ATA 4 1 = In-order data delivery enabled 3 1 = Device initiated power management enabled 2 1 = DMA Setup auto-activation enabled 1 1 = Non-zero buffer offsets enabled F0 Shall be cleared to zero
80
01FEh
81
0021h
82
F/V
0068h
F F F F F F F F F F F F F F F F F
Major version number 0000h or FFFFh = device does not report version 15 Reserved 14 Reserved for ATA/ATAPI-14 13 Reserved for ATA/ATAPI-13 12 Reserved for ATA/ATAPI-12 11 Reserved for ATA/ATAPI-11 10 Reserved for ATA/ATAPI-10 9 Reserved for ATA/ATAPI-9 8 Reserved for ATA/ATAPI-8 7 1 = supports ATA/ATAPI-7 6 1 = supports ATA/ATAPI-6 5 1 = supports ATA/ATAPI-5 4 1 = supports ATA/ATAPI-4 3 Obsolete 2 Obsolete 1 Obsolete 0 Reserved Minor version number
X F F F X F F F F F F F F F F F
Command set supported 15 Obsolete 14 1 = NOP command supported 13 1 = READ BUFFER command supported 12 1 = WRITE BUFFER command supported 11 Obsolete 10 1 = Host Protected Area feature set supported 9 1 = DEVICE RESET command supported 8 1 = SERVICE interrupt supported 7 1 = release interrupt supported 6 1 = look-ahead supported 5 1 = write cache supported 4 Shall be cleared to zero to indicate that the PACKET Command feature set is not supported 3 1 = mandatory Power Management feature set supported 2 1 = Removable Media feature set supported 1 1 = Security Mode feature set supported 0 1 = SMART feature set supported
Datasheet Wintec Slim SATA Drive W2ESxxxG1TA-J71xx Version 1.0
6/30/2014 www.wintecind.com Page 11
Word
Value
F/V
F F F F F F F F
Description Command sets supported 15 Shall be cleared to zero 14 Shall be set to one 13-9 Reserved 8 1 = SET MAX security extension supported 7 Reserved 6 1 = SET FEATURES subcommand required to spinup after power-up 5 1 = Power-Up In Standby feature set supported 4 1 = Removable Media Status Notification feature set supported 3 1 = Advanced Power Management feature set supported 2 1 = CFA feature set supported 1 1 = READ/WRITE DMA QUEUED supported 0 1 = DOWNLOAD MICROCODE command supported
F F F F F
Command set/feature supported extension 15 Shall be cleared to zero 14 Shall be set to one 13-2 Reserved 1 1 = SMART self-test supported 0 1 = SMART error logging supported
0008h
X F F F X V F V V V V F F F V V
Command set/feature enabled 15 Obsolete 14 1 = NOP command enabled 13 1 = READ BUFFER command enabled 12 1 = WRITE BUFFER command enabled 11 Obsolete 10 1 = Host Protected Area feature set enabled 9 1 = DEVICE RESET command enabled 8 1 = SERVICE interrupt enabled 7 1 = release interrupt enabled 6 1 = look-ahead enabled 5 1 = write cache enabled 4 Shall be cleared to zero to indicate that the PACKET Command feature set is not supported. 3 1 = Power Management feature set enabled 2 1 = Removable Media feature set enabled 1 1 = Security Mode feature set enabled 0 1 = SMART feature set enabled
5000h
F F F F V V V F
Command set/feature enabled 15-9 Reserved 8 1 = SET MAX security extension enabled by SET MAX SET PASSWORD 7 See Address Offset Reserved Area Boot, INCITS TR27:2001 6 1 = SET FEATURES subcommand required to spin-up after power-up 5 1 = Power-Up In Standby feature set enabled 4 1 = Removable Media Status Notification feature set enabled 3-1 1 = Advanced Power Management feature set enabled 0 1 = DOWNLOAD MICROCODE command supported
F F F F F
Command set/feature default 15 Shall be cleared to zero 14 Shall be set to one 13-2 Reserved 1 1 = SMART self-test supported 0 1 = SMART error logging supported
F F F
83
84
85
86
87
5000h
4000H
4000h
Datasheet Wintec Slim SATA Drive W2ESxxxG1TA-J71xx Version 1.0
6/30/2014 www.wintecind.com Page 12
Word
Value
F/V V
Description 15-14 13
V 12 V 11 V 10 88
Xh
F F F F F F F F F
9 8 7-6 5 4 3 2 1 0
Reserved 1 = Ultra DMA mode 5 is selected 0 = Ultra DMA mode 5 is not selected 1 = Ultra DMA mode 4 is selected 0 = Ultra DMA mode 4 is not selected 1 = Ultra DMA mode 3 is selected 0 = Ultra DMA mode 3 is not selected 1 = Ultra DMA mode 2 is selected 0 = Ultra DMA mode 2 is not selected 1 = Ultra DMA mode 1 is selected 0 = Ultra DMA mode 1 is not selected 1 = Ultra DMA mode 0 is selected 0 = Ultra DMA mode 0 is not selected Reserved 1 = Ultra DMA mode 5 and below are supported 1 = Ultra DMA mode 4 and below are supported 1 = Ultra DMA mode 3 and below are supported 1 = Ultra DMA mode 2 and below are supported 1 = Ultra DMA mode 1 and below are supported 1 = Ultra DMA mode 0 is supported
89 90
0000h 0000h
F F
Time required for security erase unit completion Time required for security erase unit completion
91
0000h
V
Current advanced power management value
92
0000h
V
Master Password Revision Code
93
0000h
X
Hardware reset result
94-126
0000h
V
Reserved
127
0000h
F F
Removable Media Status Notification feature set support 15-2 Reserved 1-0 00 = Removable Media Status Notification feature set not supported 01 = Removable Media Status Notification feature supported 10 = Reserved 11 = Reserved Security status 15-9 Reserved 8 Security level 0 = High, 1 = Maximum 7-6 Reserved 5 1 = Enhanced security erase supported 4 1 = Security count expired 3 1 = Security frozen 2 1 = Security locked 1 1 = Security enabled 0 1 = Security supported Vendor Specific
128
0001h
129-159
0000h
F V F F V V V V F X
160-254
0000h
X
Reserved
255
0000h
X
Integrity word 15-8 Checksum 7-0 Signature
Note: F/V = Fixed/variable content F = the content of the word is fixed and does not change. For removable media devices, these values may change when media is removed or changed. V = the contents of the word is variable and may change depending on the state of the device or the commands executed by the device. X = the content of the word may be fixed or variable.
Datasheet Wintec Slim SATA Drive W2ESxxxG1TA-J71xx Version 1.0
6/30/2014 www.wintecind.com Page 13
3.3 ATA Command Description: SET FEATURES (EFh) Table 12: Features Register value and available operating mode Value 02h 03h 55h 82h 90h AAh
Description Enable write cache Set transfer mode based on value in Sector Count register Disable read look-ahead feature Disable write cache Disable write cache Enable read look-ahead feature
3.4 SMART Command Support The J7 series SSD drive supports basic SMART command Set used to define some vendor -specific data to report spare/bad block numbers in each memory management unit.
Table 13: SMART Command Set Value D0h D2h D8h DAh
Command Read Data attributes Enable/Disable attribute auto save Enable SMART operation Return Status
Value D1h D3h D9h
Command Read attribute Threshold Save attribute Values Disable SMART operation
3.4.1 SMART Attribute Sector The following 512 bytes defines the SMART format. Users can obtain the data using the “Read Data” command.
Table 12: SMART Attribute Data Structure Byte 0-1 2-13 14-361 362 363 364-365 366 367 368-369 370 371 372 373 374-510 511
Description Data Structure revision number 1st attribute data nd th 2 -30 Individual attribute data Off-line data collection status Self-test execution status Total time in seconds to complete off-line data collection Reserved Off-line data collection capability SMART capability Error logging capability Self-test failure checkpoint Short self-test routine recommended polling time (in minutes) Extended self-test routine recommended polling time (in minutes) Reserved Data structure checksum
Datasheet Wintec Slim SATA Drive W2ESxxxG1TA-J71xx Version 1.0
6/30/2014 www.wintecind.com Page 14
3.4.2 Supported SMART Attributes The following table summarizes the SMART attribute Menu.
Table 13: SMART Attribute Menu Summary ID 1 2 3 5 7 8 9 10 12 168 170 173 175 192 194 197 240
HEX 01h 02h 03h 05h 07h 08h 09h 0Ah 0Ch A8h AAh ADh AFh C0h C2h C5h F0h
Attribute Name Read Error Rate Throughput Performance Spin up time Reallocated Sector Count Seek Error Rate Seek Time Performance Power-On hours Count Spin Retry Count Device Power Cycle Count SATA PHY Error Count Bad Block Count Erase Count Bad Cluster Table Count Unexpected power Loss Count Temperature Current Pending Sector Count Write Head
Datasheet Wintec Slim SATA Drive W2ESxxxG1TA-J71xx Version 1.0
6/30/2014 www.wintecind.com Page 15
4.0 Physical Specifications Table 14: Physical Specifications Common Dimensions (mm) Symbol A B C D E F G H I
Min 53.85 2.15 3.85
Max 54.15 2.45 4.00 4.15
Nom 39.00 54.00 49.40 25.00 2.30 0.80 33.39 4.00
I
G F
A D
E C B
H
Figure 2: Physical Dimensions
Datasheet Wintec Slim SATA Drive W2ESxxxG1TA-J71xx Version 1.0
6/30/2014 www.wintecind.com Page 16
5.0 Ordering Information Wintec Slim SATA SSD JM608 Series Table 15: Product Availability List & Naming Part Number
(I)
NAND Flash Type
User Capacity
W2ES004G1TA(I)-J71yy-zzz.aa
MLC
3.5GB
W2ES008G1TA(I)-J71yy-zzz.aa
MLC
7.5GB
W2ES016G1TA(I)-J71yy-zzz.aa W2ES032G1TA(I)-J71yy-zzz.aa W2ES050G1TA(I)-J71yy-zzz.aa W2ES064G1TA(I)-J71yy-zzz.aa
MLC MLC MLC MLC
15GB 30GB 50GB 60GB
W2ES128G1TA(I)-J71yy-zzz.aa
MLC
120GB
Operating Temperature Blank : Commercial Temp I : Industrial Temp
Note: I temp option only available with Micron Die (yy) Flash IC Manufacturer and Die Revision M: Micron A: A die T: Toshiba C: C die F: F die
(zzz) Component Flash Configuration 002: 2-Nand, Single Die Package, 1-CE 02D: 2-Nand, Dual Die Package, 1-CE 2D2: 2-Nand, Dual Die Package, 2-CE 2Q2: 2-Nand, Quad Die Package, 2-CE 004: 4 Nand, Single Die Package, 1-CE 4D2: 4-Nand, Dual Die Package, 2-CE 4Q2: 4-Nand, Quad Die Package, 2-CE
Note: Contact Wintec for current die Revision. (aa) Firmware Revision/Options Please contact the factory for the latest firmware revisions, custom labeling and programming identification.
Datasheet Wintec Slim SATA Drive W2ESxxxG1TA-J71xx Version 1.0
6/30/2014 www.wintecind.com Page 17
Contact Us (US & Int’l) Wintec Industries OEM Sales 675 Sycamore Drive Milpitas, CA 95035 Ph: 408-856-0500 Fax: 408-856-0501
[email protected] http://www.wintecind.com/oem
About Wintec Industries, Inc.: Wintec Industries, founded in 1988, is headquartered in Milpitas, California. Wintec, an ODM/OEM solution provider, specializes in product designs and manufacturing, including Flash modules (CF, SD, USB, embedded Flash, SSD, etc), DRAM modules (RDIMM, SODIMM, UDIMM), wireless products, modem products (embedded and USB), Advanced Digital Display products (ADD2 DVI, HDMI, digital signage), and so on. With experienced engineering team in Silicon Valley, Wintec provides a wide range of services and solutions for customers. Wintec is ISO9001-2000 certified. Important Notice: Wintec Industries makes no representations or warranties with respect to the contents of this datasheet and specifically disclaims any implied warranties of any product design for any particular purpose. Wintec Industries reserves the rights to revise this publication and to make changes from time to time in the content hereof without obligation of Wintec Industries to notify any person or organization of such revisions or change.
Datasheet Wintec Slim SATA Drive W2ESxxxG1TA-J71xx Version 1.0
6/30/2014 www.wintecind.com Page 18
