Transcript
Technical Overview
Rotary Controller Operation
The ZBARLED1000 will dim a variety of loads, primarily LED, but also CFL and Tungsten. The technology used to control the current waveform means it can dim leading or trailing edge lamps or dimmable drivers with zero visible flicker.*
Push on and off, turn control knob clockwise to increase light load, anti-clockwise to decrease light load. Note : When dimming your lights with multiple rotary controllers the light levels are adjusted from the last setting selected at that switch point.
The product has built-in thermal, overload and short circuit shutdown, protecting it from failure, it is designed to fit both new and existing installations. Control of the unit can be made via a rotary controller (part number ZBARROT), where up to 32 rotary controllers can be connected in parallel to one ZBARLED. Alternatively, control can be made via two different types of push to make retractive switches; the first type being push to make only, the second type being a rocker push up and down. Each controller or switch may be connected on existing twin and earth wiring.
Setting the minimum level pre-set (MLP)
• Turn light on and turn control knob fully clockwise for full brightness. • Press to turn off. • Turn control knob fully anti clockwise and press to turn on, the lights will then flash and the dimmer is in programming mode. • Rotate the control knob to adjust the light level. • Once you have achieved the desired minimum level, leave the control knob for 5 seconds and the lights will then flash, the dimmer has then stored the minimum level.
* Zero flicker on all tested lamps. INSTALLATION MUST BE CARRIED OUT BY A QUALIFIED ELECTRICIAN
• This product must be installed in accordance with the relevant wiring regulations. • Switch off mains supply • Decide on a suitable location for the dimmer pack with adequate ventilation and ensure the dimmer is mounted away from insulation • If multiple units are mounted within close proximity, ensure a 15mm gap between units • Commence connections as per appropriate wiring diagrams and in accordance with the relevant wiring regulations
General Wiring Diagram
TYPE
IN-LINE REMOTE PACK
PRODUCT REF
ZBARLED1000
LAMP TYPE
T
LV
LED
CFL
MAX WATT
1000
1000
1000
1000
5
5
5
MIN WATT
5
SIZE (MM)
126 X 51 X 34 appx.
Wiring With Retractive Push Up/Down Switches * IMPORTANT! No Connection, Terminate in a suitable connector to isolate
SUPPLY
ZBARLED MULTI - POINT DIMMER
LIGHTING JOINT BOX
LAMPS
ZBARLED Multi Point Remote Dimming Pack
LAMPS NC* NC*
ROTARY/ RETRACTIVE SWITCHES Permanent Live
RETRACTIVE PUSH UP/DOWN SWITCHES
RETRACTIVE PUSH UP/DOWN SWITCHES
Continue to add switches as required
Wiring With Rotary Controllers
Wiring With Retractive Push Switches
* IMPORTANT! No Connection, Terminate in a suitable connector to isolate
LAMPS
ZBARLED Multi Point Remote Dimming Pack
* IMPORTANT! No Connection, Terminate in a suitable connector to isolate
LAMPS
ZBARLED Multi Point Remote Dimming Pack
NC* NC*
NC* NC*
Suitable Twin & Earth
ROTARY CONTROLLER
ROTARY CONTROLLER
Add up to 32 controllers as required
RETRACTIVE PUSH SWITCHES
RETRACTIVE PUSH SWITCHES
Continue to add switches as required
Permanent Live
Retractive / Push To Make Single Switch Operation
• Adjust light level by pressing the switch. • You can press the switch as many times as you like. Each time
• A brief press of the switch will bring the lights on or off. • Push and hold the switch and the light level will increase
the switch is pressed, the lights will dim in the opposite direction. If the switch is not pressed for a period of 5 seconds the lights will flash and the dimmer is out of programming mode.
until they reach maximum. • Release the switch and push again. • The light level will decrease until they reach the minimum. • A single press will turn the lights on or off. • The lights will come on at their last setting. Setting the minimum level pre-set (MLP)
• Press and hold the switch until the lights are at maximum. • Release the switch and instantly press the switch again. The lights will dim down. Hold the switch in for a further 5 seconds, the lights will then flash. • You are now in programming mode.
Retractive Up & Down Switch Operation
• As above, but with the added feature of having a separate switch for up and down. Setting the minimum level pre-set (MLP)
• As above, but using the separate switch position for up and down.
Zano Controls
Guarantee
Zano Controls produces a range of dimmer switches and lighting control systems. For our full range of products see our website or pick up a brochure from one of our stockists.
1. The Company guarantees at its entire discretion either to replace or repair any of the Goods which within the Guarantee period of the Goods are shown to its satisfaction to be defective through faulty material or workmanship alone, provided that no attempt has been made by the Customer or a third party to rectify, dismantle or alter the Goods in any way. 2. The Guarantee period for any Goods is as specified at the time in the Company’s catalogue current at the time of acceptance of the Customer order and commences on the delivery of the Goods.
Contact us at Zano Controls Unit 1 Chantry Court, Wrythe Lane, Carshalton, Surrey, SM5 2DG Tel : 0845 519 5858 Fax : 0845 519 5757
[email protected] www.zanocontrols.co.uk
3. All terms, conditions , warranties, or representations, whether expressed or implied, as to description, condition, quality or fitness for purpose of any of the Goods are hereby excluded. 4. So far as permitted by statue, the Company shall not be liable for loss or damage whether direct or consequential and whether suffered by or occasioned to the Customer, it’s employees or agents or to any third party. Our full terms and conditions can be found on our website www.zanocontrols.co.uk.
Designed & Built in the U.K
Terms & conditions apply, please see our website www.zanocontrols.co.uk For further safety & certification information see www.zpatent.co.uk Certification No.188763
IZBARLED1000 / 15/10/14
