Transcript
INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação
Istruzioni di installazione Installatie-instructies Instructions d´installation
(with short uprights) (with long uprights)
Outdoor Non-Articulating Wall Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description
SB-WM46NA
SB-WM46NA
Installation Instructions
DISCLAIMER SunBriteTV LLC (SBTV) intend to make this manual accurate and complete. However, SBTV makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. SBTV makes no representation of warranty, expressed or implied, regarding the information contained herein. SBTV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
WARNING: Exceeding the weight capacity can result in
SunBriteTV® is a registered trademark of SunBrite TV LLC. Built to SunBriteTV® specifications by Chief Manufacturing. All rights reserved.
WARNING: Never operate this mounting system if it is
DEFINITIONS MOUNTING SYSTEM: A MOUNTING SYSTEM is the primary Chief product to which an accessory and/or component is attached. ACCESSORY: AN ACCESSORY is the secondary Chief product which is attached to a primary Chief product, and may have a component attached or setting on it.
serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components attached to the SB-WM46NA up to (and including) the display does not exceed 175 lbs (80 kg).
WARNING: Use this mounting system only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
damaged. Return the mounting system to a service center for examination and repair.
IMPORTANT ! : The SB-WM46NA mounts are designed to be mounted to a 2" x 4" wood studs (16" or 24" on center) wall with a maximum covering of 5/8" thick drywall, plywood, OSB, fiberboard, buffalo board or other similar sheathing materials. IMPORTANT ! : The SB-WM46NA mounts may be installed to a bare 8" concrete wall (16" or 24" on center) if 5/16 x 3" Buildex® Tapcon® anchors with Blue Climaseal® coating (not included) are used in place of lag bolts (W) provided.
COMPONENT: A COMPONENT is an audiovisual item designed to be attached or resting on an accessory or mounting system such as a video camera, CPU, screen, display, projector, etc.
WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all mounting systems/ accessories are properly assembled and installed using the instructions provided.
WARNING: Failure to provide adequate structural strength for this mounting system can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this mounting system is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component.
2
--SAVE THESE INSTRUCTIONS--
Installation Instructions
SB-WM46NA
DIMENSIONS
.79 (10X) 20
15 TILT
3
SB-WM46NA
Installation Instructions
LEGEND
4
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Marcar con lápiz
Befestigungsteil festziehen
Stiftmarkierung
Apertar fixador
Marcar com lápis
Serrare il fissaggio
Segno a matita
Bevestiging vastdraaien
Potloodmerkteken
Serrez les fixations
Marquage au crayon
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Perforar
Befestigungsteil lösen
Bohrloch
Desapertar fixador
Fazer furo
Allentare il fissaggio
Praticare un foro
Bevestiging losdraaien
Gat boren
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
Kreuzschlitzschraubendreher
Einstellen
Chave de fendas Phillips
Ajustar
Cacciavite a stella
Regolare
Kruiskopschroevendraaier
Afstellen
Tournevis à pointe cruciforme
Ajuster
Open-Ended Wrench
Remove
Llave de boca
Quitar
Gabelschlüssel
Entfernen
Chave de bocas
Remover
Chiave a punte aperte
Rimuovere
Steeksleutel
Verwijderen
Clé à fourche
Retirez
By Hand
Optional
A mano
Opcional
Von Hand
Optional
Com a mão
Opcional
A mano
Opzionale
Met de hand
Optie
À la main
En option
Hex-Head Wrench
Security Wrench
Llave de cabeza hexagonal
Llave de seguridad
Sechskantschlüssel
Sicherheitsschlüssel
Chave de cabeça sextavada
Chave de segurança
Chiave esagonale
Chiave di sicurezza
Zeskantsleutel
Veiligheidssleutel
Clé à tête hexagonale
Clé de sécurité
Installation Instructions
SB-WM46NA
TOOLS REQUIRED FOR INSTALLATION
7/32" - wood stud 1/4" - concrete
1/2" (12.7mm) -wood stud 3/8" (9.5mm) - concrete
#2
PARTS
A (1) [wall plate]
B (1) [left interface bracket - short]
C (1) [right interface bracket - short]
W (4) 5/16 x 3 1/2”
X (4) 5/16”
D (2) [interface bracket - long] 5/16 x 3" Buildex Tapcon® anchors with Blue Climaseal® coating (not included)
F (4) M8 x 20mm
K (4) M5 x 16mm
R (4) 12.7mm
G (4) M8 x 30mm
L (4) M5 x 20mm
T (4) 6.40mm
M (4) M5 x 25mm
U (4) #10
H (4) M6 x 16mm
N (4) M4 x 16mm
J (4) M6 x 25mm
P (4) M4 x 20mm
Q (4) M4 x 25mm
V (4) 1/4”
5
SB-WM46NA
Installation Instructions
ASSEMBLY and INSTALLATION 7/32"
INSPECT MOUNT BEFORE ASSEMBLY 1.
Carefully inspect the mount components for shipping damage.
2.
If any damage is apparent, call your carrier claims agent and do not continue with the installation until the carrier has reviewed the damage.
3
24" studs installation x4
4
(W) x 4
(A)
NOTE: Read all assembly instructions before starting the installation process.
Wall Plate Installation IMPORTANT ! : The SB-WM46NA mounts are designed to be mounted to a 2" x 4" wood studs (16" or 24" on center) wall with a maximum covering of 5/8" thick drywall, plywood, OSB, fiberboard, buffalo board or other similar sheathing materials. IMPORTANT ! : The SB-WM46NA mounts may be installed to a bare 8" concrete wall (16" or 24" on center) if 5/16 x 3" Buildex® Tapcon® anchors with Blue Climaseal® coating (not included) are used in place of lag bolts (W) provided.
(X) x 4
Figure 2
Wood Stud Installation 5.
WARNING: It is the responsibility of the installer to verify that the structure to which the mount is anchored will safely support five times the combined load of all attached components and equipment. 1.
Determine a suitable mounting location and lift the wall plate (A) into mounting position on wall.
2.
Using a small nail or screw (not provided) in the center hole, lightly support the wall plate at the mounting location. (See Figure 1)
3.
Level the wall plate (A) and drill 7/32” pilot holes for anchoring the wall plate. Holes must be drilled at the center of wood studs. (See Figure 1) or (See Figure 2)
4.
Using four 5/16 x 3 1/2” lag bolts (W) and four 5/16” washers (X), install the wall plate (A) on the wall. (See Figure 1) or (See Figure 2)
Slide the latches out on the wall mount in preparation for installing display. (See Figure 3)
5
5
Figure 3 16" studs installation 7/32”
3
x4
4
(A)
(X) x 4
Figure 1
6
(W) x 4
Installation Instructions
SB-WM46NA
Interface Bracket Installation
Concrete Installation WARNING: It is the responsibility of the installer to verify that the structure to which the mount is anchored will safely support five times the combined load of all attached components and equipment. 1.
Determine a suitable mounting location and lift the wall plate (A) into mounting position on wall.
2.
Using a small nail or screw (not provided) in the center hole, lightly support the wall plate at the mounting location. (See Figure 4)
3.
Level the wall plate (A) and drill 1/4" pilot holes for anchoring the wall plate. Holes must be drilled between 16" and 24" apart. (See Figure 4)
4.
Using four Buildex® Tapcon® anchors and four 5/16” washers (X), install the wall plate (A) on the wall. (See Figure 4)
1.
Place display face down on a soft, non-abrasive surface.
2.
(If applicable) Remove four sets of bolts and washers that were shipped attached to the back of the display. (See Figure 6)
2
concrete installation 1/4"
Figure 6
Buildex®Tapcon® anchors x 4
4 3
x4
x4
WARNING: IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Using screws of improper size may damage your display. Properly sized screws will easily and completely thread into display mounting holes. If spacers are required, be sure to use longer screws of the same diameter.
(A) 16
”-
24 ”
NOTE: Use short brackets (B and C) if installing to 46" or 55" models or install long interface brackets (D) to short brackets (See Steps 3 and 4) if installing to 65" models. (See Figure 9) or (See Figure 10)
(X) x 4 3.
(If installing to 65" displays ONLY) Remove six hex nuts, six washers and six screws holding interface brackets (B and C) together. Set hardware aside for reuse. (See Figure 7)
Figure 4 washers x 6 5.
Slide the latches out on the wall mount in preparation for installing display. (See Figure 5)
screws x 6
5
5 3
hex nuts x 6
Figure 5 Figure 7
7
SB-WM46NA 4.
Installation Instructions
(If installing to 65" displays ONLY) Use six removed hex nuts, six removed washers and six removed screws to assemble two long interface brackets (D) to remaining tilt assembly. (See Figure 8)
(D) x 2
(C)
(F-Q) x 4
4
(B) tilt assembly
(U) x 4 (w/M4 and M5 screws ONLY)
screws x 6
4
hex nuts x 6
washers x 6
(R or T) x 4 (if necessary)
(V) x 4
(46" or 55" models)
Figure 8 5.
Figure 9
Place left and right interface brackets (B and C) or (D x 2) on the back of the display, with the tension knob on each bracket facing toward the outside of the television. (See Figure 9) or (See Figure 10)
NOTE: Spacers (R and T) are used to offset the bracket if the (D) x 2
mounting holes are recessed or to get around the protrusions. 6.
Secure the left and right interface bracket assemblies (B and C) or (D x 2) to the display. Select the mounting hardware that fits your application. (See Figure 9) • • •
(R or T) x 4 (if necessary)
Use spacers (R or T), if necessary. Use M6 screws (H or J) or M8 screws (F or G), and 1/4" washers (V). Or, use M4 screws (N, P or Q) or M5 screws (K, L or M), 1/4" washers (V) and #10 washers (U).
(U) x 4 (w/M4 and M5 screws ONLY)
(D) (V) x 4
4
(F-Q) x 4
(65" models) Figure 10
8
Installation Instructions
SB-WM46NA
Display Installation (46" or 55" models shown)
2 WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components located between the SB-WM46NA up to (and including) the display does not exceed 175 lbs (80 kg). 1.
Place the display on the wall plate (A) by hooking the hooks of the brackets (B and C) or (D and E) in the top of the wall plate. (See Figure 11)
2.
Secure the display by sliding the latches, one on each side, inward. As the latches are slid in, it will lower and catch the bottom hook and secure the television in place. (See Figure 11)
3.
If desired, install self tapping screws (not provided) and/or padlocks (not provided) for additional security. (See Figure 11)
2
tilt adjustment knobs
(46" or 55" models shown) 3
x 2 (optional)
Figure 12
Display Removal To remove display:
CAUTION: Disconnect power and audio/video cables
3
before removing the display from its wall mount.
WARNING: The display is heavy and extremely fragile. Exercise caution when removing the display from the mount to avoid equipment damage or personal injury.
1 2 1
1.
If applicable, remove the self tapping screws (not provided) and/or padlocks from both sides of the wall plate. This hardware provides security. (See Figure 13)
2.
Slide the security latches out on both sides to disengage the display from the wall plate. (See Figure 13)
3.
With an assistant, lift the display up and off the wall plate to remove the display from the wall. (See Figure 13)
(46" or 55" models sown)
2
x2
1
3
Figure 11 2
Tilt Adjustment 1.
Adjust tilt tension adjustment knobs to desired tension. (See Figure 12)
2.
Adjust tilt of display by pulling the top of display away from the wall until desired tilt position is reached. (See Figure 12)
3.
Tighten tilt tension adjustment knobs to secure tilt position. (See Figure 12)
2 Figure 13
9
SB-WM46NA
10
Installation Instructions
Installation Instructions
SB-WM46NA
11
SB-WM46NA
Installation Instructions
SunBriteTV, LLC 2001 Anchor Court Thousand Oaks, CA 91320 8800-002841 Rev01 04/17
866-357-8688 www.sunbritetv.com
