Transcript
ASSEMBLY INSTRUCTIONS
WorkFit-LX, Sit-Stand Desk Mount System
< 25 lbs (11.3 kg) Maximum Screen Size* = 42” *Limited to 25 lbs maximum
0-5 lbs (0-2.3 kg)
ENGLISH
CLAMP
GROMMET HOLE
0.78"-2.56" (20-65mm)
0.78”-2.25” (20-57mm)
0.5"-2.5" (13-64mm)
Tools Needed 1/4"
For the latest User Installation Guide please visit: www.ergotron.com User's Guide - English Guía del usuario - Español Manuel de l’utilisateur - Français Gebruikersgids - Deutsch Benutzerhandbuch - Nederlands Guida per l’utente - Italiano Användarhandbok - svenska ユーザーガイド : 日本語 用户指南 : 汉语 888-45-323-G-00 rev.B • 04/15
1 of 19
Features & Specifications 360°
70°
360° 20" (508 mm)
180°
5°
180°
90° 20" (508 mm)
180°
5°
360°
ENGLISH
3°
3°
Safety CAUTION: DO NOT rotate monitor past rear edge of desk. Doing so will create an unstable situation and may cause equipment damage or personal injury.
CAUTION: Monitor may hit Keyboard arm in some configurations. Use caution when moving your monitor and keyboard arms.
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or difficult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
888-45-323-G-00 rev.B • 04/15
2 of 19
Components A
1
B
C
1x
1x
D
4x
1x
4x
M4 x 12mm M5 x 12mm
2x 4x
2
1x 1x
4x
M6 x 12mm
1x
1x
M3 x 6mm
3
4x M4 x 10mm
1x
4x
1x
M4 x 10mm
1x
1x
4x
4x M5 x 7mm
2x 2x 5
2x
2x
4x
1x
M6 x 45mm
6
M5 x 20mm
M6
2x
1x 4mm
4x
6x
4x 2.5mm
M8M5 Converter
8mm
1x
5mm
1x
4x 1/4”
M4 x 8mm
2x
M4 x 14mm
888-45-323-G-00 rev.B • 04/15
3 of 19
ENGLISH
4
1x 1x
4x
1 Desk Placement
Maximum dimensions to allow keyboard arm to lower below front of desk.
13.3" (338 mm)
Side View
CAUTION: Base must be completely on desk surface. Failure to follow these instructions may result in equipment damage or personal injury.
CLAMP
5.9" (150 mm)
11.7" (297 mm)
Side View
Front of Desk
19.2" (488 mm)
5.9" (150 mm)
17.6" (447 mm)
Top View
Front of Desk
Top View 13.3" (338 mm)
ENGLISH
GROMMET HOLE
Grommet hole can be located anywhere along this arch. 11.7" (297 mm)
10.75" (273 mm) Front of Desk
Front of Desk
10.75” (273 mm)
5.9" (150 mm)
Front of Desk
Front of Desk
10.3" (262 mm)
5.9" (150 mm)
10.3" (262 mm)
Corner mount - Top View
Corner mount - Top View
Example of one configuration
1.75" (44 mm)
23.6" (599 mm) 10.3" (262 mm)
3.7" (93 mm)
19.2" (488 mm) 18.3" (466 mm)
22" (559 mm) 3.7" (93 mm)
10.3" (262 mm) 17.6" (447 mm)
18.3" (466 mm)
11.5" (292 mm) 888-45-323-G-00 rev.B • 04/15
4 of 19
2 CLAMP
GROMMET HOLE
DESK THICKNESS 0.78"-1.38" (20-35mm)
1.18"-2.56" (30-65mm)
a
4mm
4mm
b 4mm ENGLISH
8mm 1/4”
1/4"
c
4mm 1x 1x
d 1x
1x
CAUTION: Bolt must be centered in hole.
888-45-323-G-00 rev.B • 04/15
5 of 19
3
Mount extension and arm to pole.
a
b
c
2.5mm
e
ENGLISH
d 2x
f
1x
M6
M6 x 45mm
4mm
4a
4x
888-45-323-G-00 rev.B • 04/15
6 of 19
b
4x M4 x 8mm
c
5a
ENGLISH
b
c 4x
d
888-45-323-G-00 rev.B • 04/15
7 of 19
6
Portrait / Landscape Options OPTION i
If you want full portrait/landscape rotation, skip to step 8 on the next page.
OPTION ii
If you do not want your TV/Monitor to rotate all all, you can stop rotation by inseting the set screw.
ENGLISH
i
ii
0˚
1x M3 x 6mm
888-45-323-G-00 rev.B • 04/15
8 of 19
7
Check size of TV/Monitor hole pattern
TV/Monitor Hole Pattern Sizes
VESA Adapter Configurations 100mm (3-15/16”) 75mm (2-15/16”) 100mm (3-15/16”)
75x75mm 100x100mm
10
100mm (3-15/16”)
200mm (7-7/8”)
B
75mm (2-15/16”)
A
100x200mm
ENGLISH
11 200mm (7-7/8”)
200x200mm
200mm (7-7/8”)
C
11 200mm (7-7/8”)
200x100mm
100mm (3-15/16”)
D
11 888-45-323-G-00 rev.B • 04/15
9 of 19
7
Mount Type A TV/Monitor to Arm
A 75x75mm 100x100mm
100mm (3-15/16”) 75mm (2-15/16”) 100mm (3-15/16”)
75mm (2-15/16”)
4x ENGLISH
M4 x 10mm
4x M4 x 10mm
OR M4 x 10mm
8 10 of 19
13
888-45-323-G-00 rev.B • 04/15
C 200x200mm
B 100x200mm
D 200x100mm
100mm (3-15/16”) 200mm (7-7/8”)
100mm (3-15/16”)
200mm (7-7/8”)
200mm (7-7/8”)
7a
200mm (7-7/8”)
Mount VESA Adapters to Arm based on TV/Monitor hole pattern size (B, C, or D) .
4x M5 x 7mm
ENGLISH
7b
Mount Type B, C, or D TV/Monitor to Arm 4x
M4 x 12mm
4x
M5 x 12mm
4x
M6 x 12mm
NOTE: To reduce M8 holes for use with M5 screws, or if you have a model with Samsung holder rings, follow the M8M5 KIT instructions on the next page.
12 888-45-323-G-00 rev.B • 04/15
11 of 19
M8M5 KIT Instructions NOTE: Follow this step only if your TV/monitor has M8 holes which need to be reduced to M5. Install M8M5 reducer bushing to TV/Monitor and use M5 x 20 mm monitor screws to secure.
4x
4x
ENGLISH
M5 x 20mm
TV/Monitor Mounting M8 size hole
NOTE: Follow this step only for Samsung models using the holder ring.
Install M8M5 reducer bushing to TV/Monitor then use M5 x 20 mm monitor screws and Samsung holder ring to secure.
4x
4x M5 x 20mm
TV/Monitor Mounting M8 size hole Holder Ring (Not included *Samsung Only)
888-45-323-G-00 rev.B • 04/15
12 of 19
8
Mount extension and arm to pole.
a 1x
c 2x
b
2.5mm
d ENGLISH
M6
e
1x 1x
M6 x 45mm
f
1x
4mm
4mm
888-45-323-G-00 rev.B • 04/15
13 of 19
9
Organize and route cables
ENGLISH
Leave enough slack in cables to allow full range of motion.
888-45-323-G-00 rev.B • 04/15
14 of 19
Adjustment Step Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or difficult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
10 To adjust the arm lift: ENGLISH
5mm CAUTION: DO NOT overtighten fasteners. Overtightening may cause damage to your equipment.
WARNING
Increase Lift Strength
5mm
WARNING
If the mounted weight is too heavy or this product does not stay up when raised, then you'll need to increase Lift Strength:
Decrease Lift Strength If the mounted weight is too light or this product does not stay down when lowered, then you'll need to decrease Lift Strength:
WARNING! Stored Energy Hazard: The arm mechanism is under tension and will move up rapidly, on its own, as soon as attached equipment is removed. For this reason, DO NOT remove equipment unless the arm has been moved to the highest position! Failure to follow this instruction may result in serious personal injury and/or equipment damage!
888-45-323-G-00 rev.B • 04/15
15 of 19
11 To adjust the TV/monitor tilt:
4mm CAUTION: DO NOT remove screw. Removing screw may cause damage to equipment.
ENGLISH
4mm
Increase Lift Strength If the mounted weight is too heavy or this product does not stay up when raised, then you'll need to increase Lift Strength:
Decrease Lift Strength If the mounted weight is too light or this product does not stay down when lowered, then you'll need to decrease Lift Strength:
888-45-323-G-00 rev.B • 04/15
16 of 19
12 Lift – Up and down 5mm
5mm CAUTION: DO NOT overtighten fasteners. Overtightening may cause damage to your equipment.
Increase Lift Strength If the mounted weight is too heavy or this product does not stay up when raised, then you'll need to increase Lift Strength:
WARNING
Decrease Lift Strength
WARNING! Stored Energy Hazard: The arm mechanism is under tension and will move up rapidly, on its own, as soon as attached equipment is removed. For this reason, DO NOT remove equipment unless the arm has been moved to the highest position! Failure to follow this instruction may result in serious personal injury and/or equipment damage!
13 To adjust height on pole: 2.5mm
888-45-323-G-00 rev.B • 04/15
17 of 19
ENGLISH
If the mounted weight is too light or this product does not stay down when lowered, then you'll need to decrease Lift Strength:
How to remove this tilting feature: 3°
3°
ENGLISH
Save these screws incase you want to add this feature later.
2x M4 x 14mm
888-45-323-G-00 rev.B • 04/15
18 of 19
Set Your Workstation to Work For YOU! Learn more about ergonomic computer use at:
www.computingcomfort.org Height Position top of screen slightly below eye level. Position keyboard at about elbow height with wrists flat. Distance Position screen an arm's length from face—at least 20” (508mm). Position keyboard close enough to create a 90˚ angle in elbow. Angle Tilt screen to eliminate glare. Tilt the keyboard back 10° so that your wrists remain flat. To Reduce Fatigue Breathe - Breathe deeply through your nose. Blink - Blink often to avoid dry eyes. Break • 2 to 3 minutes every 20 minutes • 15 to 20 minutes every 2 hours.
ENGLISH
For local customer care phone numbers visit: http://contact.ergotron.com
NOTE: When contacting customer service, reference the serial number.
888-45-323-G-00 rev.B • 04/15
19 of 19
