Wp75sat-hd

Transcript

OPERATING INSTRUCTIONS WP75SAT-HD DIGITAL SATELLITE RECEIVER BE WALKER WISE...logon to www.walker.ie Contents Overview of the Remote Control ............................ 4 Connections............................................................ 5 Remote Control ...................................................... 6 Connection to the TV .............................................. 6 Power On-Off.......................................................... 7 LNB Connection ..................................................... 7 AUDIO CONNECTORS.......................................... 7 USB Disk Connection ......................................... 8 Programme Recording........................................ 8 Menu Interface / First Time Installation................... 9 Instant Recording ................................................. 10 Electronic Programme Guide (EPG) .....................11 Menu System.........................................................11 Channel List...........................................................11 Navigating the Entire Channel List ............... 12 Moving the channels in the channel list ........ 12 Deleting the Channels in the Channel List .... 12 Renaming Channels ..................................... 12 Adding Locks to Channels ............................ 13 Setting Favourites ......................................... 13 Adding a Channel to a Favourites List ...13 Removing a Channel from Favourite List13 SETUP.................................................................. 13 The adjustments in this menu are;.................... 13 Installation......................................................... 13 Automatic channel scan ................................ 14 Manual channel scan .................................... 14 SatFree Scan ................................................ 14 First Time Installation .................................... 14 Country ...................................................15 Output Settings .......................................15 Receiver Upgrade ......................................... 15 Menu Locking ............................................... 15 Menu Lock .................................................... 15 Set Pin .......................................................... 16 Time Settings (Optional) ............................... 16 HDMI HDCP.................................................. 16 Automatic Power Down ................................ 16 Language .......................................................... 16 Recording configuration .................................... 16 Auto discard............................................16 Format Drive ...........................................17 Load Settings ................................................ 17 Save Settings ................................................ 17 Internet Settings................................................ 17 Recordings Library ............................................... 17 Media Browser...................................................... 18 Playing MP3 Files ............................................. 18 Slideshow Options ............................................ 19 Timers ................................................................... 19 Remote Control .................................................... 21 Digital Capabilites ................................................. 21 TV Scart................................................................ 21 English - 1 - 01_S7100_[GB]_DVB660_1102UK_10075948_50201311.indd 1 28.11.2011 08:37:10 Features •  5 000 channels TV and Radio programs • Auto,1/4,1/3,2/5,1/2,3/5,2/3,3/4,4/5,5/6,8/9 ,9/10 for DVB-S2 QPSK • Media Browser ( USB 2.0 ) Support • Auto,3/5,2/3,3/4,5/6,8/9,9/10 for DVB-S2 8PSK • DVB-S2/S Compliant • Symbol Rate: 2 to ~ 45 Msps for DVB-s • HDMI Output (576p, 720p, 1080i resoluitons support) • Symbol Rate: 5 to ~ 30 Msps for DVB-S2 •  C hannel lock • P r e s e n t / N e x t e v e n t i n f o r m a t i o n ( 7 - D AYEPG) • Recording timers • Video Decoding: MEPG2 MP@ML,PAL/ NTSC 4:3 16:9, MPEG4 AVC/H.264 HP@ L4 16:9 • Video Out: PAL • Audio Decoding: M P E G - 1 L AY E R I / I I , MPEG-2 LAYER II, MPEG-2 AAC, MPEG-4 AAC • Mheg support • SatFree scan • 32-bit OSD color, 720x576 pixels for PAL • Parental lock at menu •  L ast watched channel saving • Signal strength bar for transponders • LNB short circuit and overload protection by software • Multi language audio support • Digital audio output (optic) • IR remote control •  Teletext function support ( DVB ) • Resetting to factory settings option • TV Scart • Ku band reception: 10.7 – 12.7 GHz • Ka band reception: 26.5 – 40 GHz (Requires Kaband LNB installation on dish) • LNB Control: Horizontal/vertical polarity switching (13V %12,825-%14,175 and 18V %17,575-%19,425), 0-22 kHz switching, tone burst A/B switching for dish selection,DiSEqC 1.2 •Selectable satellite configurations ( P r e s e t s : A S T R A , H O T B I R D , T U R K S AT 2A/3A.etc) • Signal strength and signal quality bars for antenna adjustment • Various channel search options: • Automatic Satellite search for preset transponders • Transponder search • Network search • FTA (Free- to- Air) search option for satellite and auto search modes • Auto FEC (Forward Error Correction) search • Auto PID correction (except user defined PIDs) • Digital Decoding Properties: • Demodulation: QPSK and 8PSK • FEC : Auto,1/2,2/3,3/4,5/6,7/8 for DVB-S QPSK English - 2 - 01_S7100_[GB]_DVB660_1102UK_10075948_50201311.indd 2 28.11.2011 08:37:11 CAUTION Safety Precautions Power Source The set should be operated only from a 220-240V AC, 50 Hz outlet. Ensure that you select the correct voltage setting for your convenience. Batteries shall not be exposed to excessive heat such as sunshine, fire or the like. WARNING: When the set is not in use for a long time, disconnect from the power. Power Cord Do not place the unit, a piece of furniture, etc., on the power cord (mains lead), or pinch the cord. Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Never make a knot in the cord or tie it with other cords. The power cords should be routed in such a way that they are not likely to be stepped on. A damaged power cord can cause fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask closest service agent for help. When the AC power cord needs to be changed, it should be done at a qualified service shop only. • Please do not place the set in a place subject to direct sun light, excessive dust or mechanical shock or in a location near heat sources. • The set should be placed on a solid and safe base. Do not place the apparatus on a soft surface such as a rug that might block the ventilation holes on the bottom. • A location should not be selected such as a room with high humidity, as the condensation, arising in the kitchen for example, may cause malfunction or damage the set. • Heating or other thermal radiation under the set also may cause malfunction or damage the set. • The hot air, which arises during the operation, should be ventilated with sufficient air circulation. Please do not put the set into closed areas and do not cover it. • Please avoid the contact of the set with water or humidity. Do not put into operation near bath, swimming pools. • Take care to provide a good air circulation. Place the apparatus in a location with adequate ventilation to prevent heat build-up in the apparatus. • Should any solid object or liquid fall into the cabinet, unplug the apparatus and have it checked by qualified personnel before operating it any further. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. The mains plug is used as the disconnect device, the disconnect device shall remain readily operable. English - 3 - 01_S7100_[GB]_DVB660_1102UK_10075948_50201311.indd 3 28.11.2011 08:37:11 Overview of the Remote Control Mute Standby Freeze Media Browser Button Teletext Electronic Program Guide SatFree mode/ Regular mode Exit Subtitle On-Off HDMI Resolution Language Navigation Buttons Menu/Back Info Channel Up/Down OK Volume Up/Down Audio mode selection Tag/Untag (In Channel list) Channel List Down Channel List Up Numerical Buttons Favourite List Programme Previous Fast forward Fast backward Recording Library Timers Play Record Stop Pause No Function Remote range is apporoximately 7m * English - 4 - 01_S7100_[GB]_DVB660_1102UK_10075948_50201311.indd 4 28.11.2011 08:37:12 Connections BACK VIEW 35027993 Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. AC IN 13/18 V Max.400mA LNB IN 1 ANALOG AUDIO OUT HDMI OUT ETHERNET 2 3 4 USB 5V DC 500mA 5 SCART (TV) DIGITAL AUDIO OUT (OPT./TOSLINK) 6 7 8 1. LNB IN :To connect satellite antenna cables. 2. STEREO AUDIO OUT: Headphone out. 3. HDMI OUT : To connect to HDMI supported TV for High Definition resolution and audio output. 4. ETHERNET : Lan connection 5. USB INPUT : Connect USB devices . 6. SCART OUT : TV SCART connection. 7. OPTICAL AUDIO OUT: Optical Digital Audio Output 8. POWER CABLE : AC IN English - 5 - 01_S7100_[GB]_DVB660_1102UK_10075948_50201311.indd 5 28.11.2011 08:37:12 Remote Control First open the battery cover on the back of the remote control. Insert two batteries 1.5Volt (RO3/AAA) referring to the imprinted symbols (+/-) in the battery case and put on the battery cover again. While using the remote control, direct it towards the front side of the receiver. If the remote control does not work or the chosen function does not work, the batteries are most probably exhausted and they should be replaced as soon as possible. Please use only the leak proof batteries. It is best to remove the batteries from the remote unit if you will not be using the remote control unit for long time. Connection to the TV To SCART socket on your device Or; To HDMI socket on your device Scart Connection: Connect your set-top box with a scart cable using the TV scart connector on the rear panel to your television’s scart connector. The set-top box gives RGB or CVBS output. If you want to get the picture via scart connector and your TV’s scart connector has an RGB input, then you can switch your settop box to RGB mode, by toggling TV out menu to RGB mode, in configuration menu. So, you will be able to achieve high performance from your set-top box. You can use scart connector to connect your box to TV and VCR devices. HDMI Connection: You can use HDMI socket to connect to HDMI supported TV for High Definition resolution and audio output. The receiver can provide HDMI output in four different resolutions from the HDMI connection on the rear panel. In order to get best picture and audio quality, please check the HDMI resolutions supported by your TV set and select the most appropriate one from this menu. Note: These two methods of connection perform the same function but in different levels of quality. It is not necessary to connect by all two methods. English - 6 - 01_S7100_[GB]_DVB660_1102UK_10075948_50201311.indd 6 28.11.2011 08:37:12 Power Connection IMPORTANT: The set-top box is designed to operate on 220-240V AC, 50 Hz. Plug the power cable to the mains socket outlet. • After unpacking, allow the set-top box to reach the ambient room temperature before you connect the set to the mains. Power On-Off Be sure that you put through all the cable connections. After plugging in the mains cord of the set-top-box to the mains supply, a light will be seen on the front panel (Standby mode). When the set-top-box is first powered up please wait for a few seconds before activating the receiver since booting of software will take some time. Then, you can turn on your set-top box by pressing the standby button on the remote control. You will see that the light on the front panel will change (Power on mode). LNB Connection AUDIO CONNECTORS The audio sockets are used to connect your set-top box to a hi-fi set. So you can listen to the TV sound or one of the numerous radio stations via your set or respectively record on a cassette recorder (Through the use of Audio outputs of the set-top box). English - 7 - 01_S7100_[GB]_DVB660_1102UK_10075948_50201311.indd 7 28.11.2011 08:37:15 USB Connection • You can connect a USB hard disk drive or USB memory stick to your box by using the USB input . This feature allows you to play files stored in a USB drive or record programmes. • 2.5” and 3.5” inch (hdd with external power supply) external hard disk drives are supported. • To record a programme, you should first connect a USB disk to your box while the it is switched off. You should then switch on the box to enable recording feature. Otherwise, recording feature will not be available. IMPORTANT ! • You may back up your files before making any connections to the box in order to avoid any possible data loss. Note that manufacturer will not be responsible for any file damage or dataloss. • It is possible that certain types of USB devices (e.g. MP3 Players) or USB hard disk drives/memory sticks may not be compatible with this device. IMPORTANT: The device may not support all disk formats. If you connect a USB disk with an unsupported format, then you will be asked to format the content. See the section, “Format Disk” in the following pages for more information on disk formatting. Note that ALL the data stored on the USB disk will be lost and then the disk format will be converted to FAT32 in such a case. USB Disk Connection • Plug your USB device to the USB input of the box. Note: Plug or unplug your USB disk while the box is switched off. Note: If you are going to connect a USB hard disk drive to the box, USB connection cable used between the disk drive and the box should have a USB logo and should be as short as possible. Note: While formatting a USB hard disk that has 1TB (Tera Byte) or more file capacity, you can experience problems with the formatting process. In such a case, you should format the disk with your personal computer and the formatted disk type is recommended as FAT32. CAUTION ! • Quickly plugging and unplugging USB devices, is a very hazardous operation. Especially, do not repeatedly quickly plug and unplug the drive. This may cause physical damage to the USB player and especially the USB device itself. • Do not pull out USB module while playing or recording a file. Programme Recording IMPORTANT: When using a new USB hard disk drive, it is recommended that you first format the disk using your device’s “Format Disk” option. • For using recording function, you should connect a USB disk or an external hard disk drive to the box and connected USB disk should have at least 1 GB capacity and should have 2.0 speed compatibility. If the connected USB device does not support 2.0 speed, an error message will be displayed. • An hour of the recordings stored occupies approximately 2 GB of space. • For more information on recording programmes, see sections “Instant Recording”, “Electronic Programme Guide”, “Recordings Library” or “Timers” in the following parts. Recorded programmes are stored in the following directory of the connected USB disk: \DVR\RECS. An .ifo file is created for each recording. This file includes information such as broadcaster, programme, and recording time. English - 8 - 01_S7100_[GB]_DVB660_1102UK_10075948_50201311.indd 8 28.11.2011 08:37:15 another menu screen will be displayed. Select an available satallite and press OK to scan for services. Menu Interface / First Time Installation When the box is opened from stand-by mode and if there is no channel stored in the database, First Time Installation Menu window will be displayed on the screen. In the first menu screen, menu language will be asked: Unicable: If you have multiple receivers and a unicable system, select this antenna type. Press OK to continue. Configure settings by following instructions on the screen. Press OK to scan for services. The appropriate operation language can be chosen by highlighting the desired language (with “ ” or “ ” keys) and pressing OK. Then, Country, Time Zone, TV type, Display format and HD output resolution selection screen will be displayed: DiSEqC: If you have multiple satellite dishes and a DiSEqC switch, select this antenna type. After selecting DiSEqC switch, another menu screen will be displayed. You can set four DiSEqC options (if available). Press OK to scan all satellites or press GREEN button to scan only the highlighted satellite. Select the desired Country, Time Zone, TV type, Display format and HD output resolution by using “ ”/“ ” buttons and press OK to continue. After pressing the OK button, antenna type will be displayed. Please select your connection type by using “ ”/“ ” buttons and press OK to continue. There are four types of antenna selection. You can select Antenna type as, Direct, Unicable, DiSEqC or Motor by using “ ”/“ ” buttons. Direct: If you have a single receiver and a direct satellite dish, select this antenna type. After selecting Direct, English - 9 - 01_S7100_[GB]_DVB660_1102UK_10075948_50201311.indd 9 28.11.2011 08:37:15 Motor: If you have a motor driven dish, select this antenna type. Configure settings as desired for positioning the motor. Instructions are present on this menu screen. Options may vary according to the motor type. When finished, press OK to scan for services. The box starts to scan services. The process of scanning will take a few minutes. You can follow the scanning process from the scroll bar. After the scanning, first time installation will be completed and scan results will be displayed on the screen. Note : Satellite selection available only in First Time Installation. To change satellite, you have to select First time installation from the Installation menu. • After setting antenna settings, press OK to continue. • You will be asked to select search type: Instant Recording IMPORTANT: To record a programme, you should first connect a USB disk to your box while the box is switched off. You should then switch on the box to enable recording feature. Otherwise, recording feature will not be available. • Press (RECORD) button to start recording an event instantly while watching a programme. The following OSD appears on the screen: Regular Scan: This option scans the selected satellite. SatFree Scan: This option will function on satellite Astra2. If you have satellite Astra2, SatFree scan will start. If this satellite is not available, a warning message appears to change search to regular scan. English - 10 - 01_S7100_[GB]_DVB660_1102UK_10075948_50201311.indd 10 28.11.2011 08:37:16 Red button : Advance +2 hours. Green button : Advance -2 hours. Yellow button: Advance +1 day. Blue button: Advance -1 day. Menu System • Record OSD will then be displayed for a short time and the current event will be recorded. Main menu is accessed by pressing the MENU button on the remote control. Navigate with “ ”/“ ” keys among the menus and press OK to activate menus. In some sub-menus, press the MENU button to return to the previous menu, otherwise, use it to back from the menu. In all menus there is an Info banner at the bottom of the screen. These are functions that can be used in the current menu • Press (STOP) button to cancel instant recording. The following OSD will be displayed: Select Yes by using “ ” or “ ” / OK buttons to cancel instant recording. Note: Switching to a different broadcast and viewing Media Browser are not available during the recording Electronic Programme Guide (EPG) Some, but not all, channels send information about the current and next events. Press GUIDE button to view the EPG menu. EPG appears on the screen. EPG gets Information of the channel - programs weekly by means of 7-DAY-EPG. All programs of channels are displayed. On the bottom of the screen; info bar, showing all the available commands, will be displayed. Channel List Using the “ ” or “ ” button on the remote control, make sure that the first item, Channel List, is highlighted and press the OK button to display Channel List or you can press the OK button during watching programme and get to the Channel List directly. There are two channel list types available in accordance with your search selection. If you search in regular mode, the following channel list will be displayed. English - 11 - 01_S7100_[GB]_DVB660_1102UK_10075948_50201311.indd 11 28.11.2011 08:37:17 Navigating the Entire Channel List Press “ ” or “ ” button for selecting the previous or next channel. You can press “RED” or “GREEN” button to move page up or page down. To watch a specific channel, highlight it using “ ” or “ ” button and then press “OK” button, while the “Select” item on Channel List menu is highlighted by using “ ” or “ ” button. Only Filtered channels will be available and can be watched if you do not disable filter mode. Moving the channels in the channel list • Press “ ” or “ ” buttons to select the channel that will be moved. • Press “ ” or “ ” buttons to select the “Move” item on Channel List menu. • Press “ ” or “ ” button to highlight the desired option. Highlight YES and press OK to delete the selected channel. Highlight NO and press OK button to cancel. Renaming Channels To rename a specific channel, the channel must be highlighted by pressing “ ” or “ ” button. Then highlight Edit Name item by pressing “ ” or “ ” button as illustrated below. Press the OK button to activate the rename feature. Note: If you enter the same programme number of the channel that you want to move, “Channel Exist. Move it?” osd will be displayed. Press OK to confirm or select “No” to cancel. Deleting the Channels in the Channel List • Press “ ” or “ ” button to select the channel that will be deleted.• Press “ ” or “ ” button to select the “Delete’’ item on Channel List menu. • Press the OK button to delete the highlighted channel in the channel list. Then the message below appears on the screen: Now pressing “ ” or “ ” button moves to the previous/ next character. Pressing “ ” or “ ” button toggles the current character, i.e., ‘b’ character becomes ‘a’ by “ ” and ‘c’ by “ ”. Pressing numeric buttons ‘0...9’ replaces the highlighted character with the characters printed above the button one by one as the button is pressed. Press the “MENU” button to cancel the editing or OK button to update the new name. English - 12 - 01_S7100_[GB]_DVB660_1102UK_10075948_50201311.indd 12 28.11.2011 08:37:17 Adding Locks to Channels Channel locking provides a password-protected access to channels selected by parents. In order to lock a channel you should know the parental lock password (default value is set to 0000 in the factory and can only be changed from the Configuration menu). SatFree mode feature is different from regular search mode. If you search in SatFree mode, the following channel list will be displayed and the list will be sorted according to LCN. Select the channel to be locked by highlighting it and select Lock option by pressing “ ” or “ ” button. Press OK button. Afterwards, a dialog OSD asking for the password will be displayed. Enter the password by using the numeric buttons on the remote control. The lock icon “ ” will be displayed next to the selected channel. Repeat the same operation to cancel the lock. Setting Favourites To set a favourite you should highlight the “Favourites” item at the bottom of the Channel List menu. Then press “OK” button and Edit Favourite List menu appears on the screen. LCN data is provided by the broadcaster and this list can not be changed. If you don’t want to use this list, you can customize the channel list by using Customize LCN function. Note : Move and Edit name functions will not available in this mode. SETUP The adjustments in this menu are; Adding a Channel to a Favourites List • By pressing “ ” or “ ” buttons, highlight the channel that you want to add to the favourite list. • By pressing “OK” button, the highlighted channel is added to the Favourite List. • Favourite icon indicates that a channel is added to Favourite List. Installation The Installation menu is mainly intended to help you for creating a channel. Select Installation from the Setup menu by pressing “ ” or “ ” buttons. This menu includes the following items: Removing a Channel from Favourite List • Highlight the channel that you want to remove from the favourite list and press OK button to remove.You can press “OK” button again to re-add a channel. English - 13 - 01_S7100_[GB]_DVB660_1102UK_10075948_50201311.indd 13 28.11.2011 08:37:18 Menu items in manual search menu will be as the following: 1. Satellite 2. DiSEqC 3 Frequency. 4. Polarization 5. Symbol rate 6. Network search Automatic channel scan 7. Scan Encrypted • Satellite Name, Polarization values and Network Search requirements are changed by toggling. • Frequency and Symbol Rate are entered directly using “0, 1, 2…, 9” keys. • As soon as entering transponder frequency, the signal level and quality will be reflected in the signal strength bars (Signal Level and Signal Quality bars) at the bottom of the menu. Signal Level bar shows the strength of the satellite signal. Signal Quality bar shows lock quality of the device for entered values. • If Network Search item selected as YES, after tuning to that transponder, the parameters of other transponders will be collected from NIT (Network Information Table) and tuning will be performed for other transponders. With this menu, you can search selected or all satellites. To do this, select “Automatic channel scan” in the Installation menu, by using the “ ”/“ ” buttons. If you press OK button, the “Automatic channel scan” menu will appear. Settings in this screen may vary in accordance with antenna type selection defined in first time installation. You can set satellite values as desired. Press GREEN button to scan selected satellite. Press BLUE button to view transponder list. You can use OK button to scan all satellites. • By pressing OK button values are stored and after the search, if a new program is found, it will be added to the programme list. Found program’s name is shown as ‘Program’. If you select SatFree scan in First time installation, Installation menu will be displayed as below. Manual channel scan SatFree Scan Searches channels in SatFree mode. To perform SatFree scan, you should use Astra2 satellite. First Time Installation This section is same with initial installation part. Please refer to Menu interface/First time installation section for more information. Note : Satellite selection available only in First Time Installation. To change satellite, you have to select First time installation from the Installation menu. This menu will be acivated by using the “ ”/“ ” buttons in the Installation menu. By pressing the OK button, English - 14 - 01_S7100_[GB]_DVB660_1102UK_10075948_50201311.indd 14 28.11.2011 08:37:18 Configuration Scart mode You can configure the settings of your set-top box. Select Configuration from Setup menu and press “OK” to view this menu. Press the “EXIT” button on the remote control to exit. The receiver can output RGB and CVBS signal from the TV SCART on the rear panel. Although the RGB format results in a better quality picture, not all equipment can cope with an RGB signal. Prefer Dolby Digital Use “ ” or “ ” button to select Dolby Digital and then press “ ” or “ ” button to set this setting as Yes or No. Spdif Output Use “ ” or “ ” button to select Spdif Output and then press “ ” or “ ” button to set this setting as LPCM or Dolby D. HDMI Resolution By pressing “ ”/ “ ” on the remote control, you can change to HDMI resolution as 576P, 720P or 1080i. Receiver Upgrade Country Use “ ” or “ ” button to select Country and then press “ ” or “ ” button to change this setting. Output Settings To ensure that your STB always has the most up to date information. Please ensure that after use it is set to its standby mode. • Press Menu button and using the “ ”/“ ” buttons to choose Setup and press the OK button. • Highlight Configuration menu with “ ”/“ ” keys and pres OK. • Use “ ”/“ ” buttons to choose “Receiver Upgrade” and press OK button. • Using the “ ”/“ ” button you can change “Automatic scanning” Enabled or Disabled. Tv Type Satellite channels can be broadcast in a widescreen format whose output can be different for normal and widescreen TV sets. This function enables to change the screen format of the TV connected, so that broadcasts are displayed correctly. Highlight the TV Type line in the Configuration menu and use the “ ”/“ ” keys to select 4:3 if you have a standard TV set connected or 16:9 if it is a widescreen TV. This function duplicates the selection made at the time of first installation and can be used if you change TV sets. Display Format Use “ ” or “ ” button to select Display Format and then press “ ” or “ ” button to set this setting as Auto, Letter Box or Pan & Scan for 4:3 tv set and Auto, pillar box, zoom for 16:9 tv set. • Highlight “Scan for upgrade” menu with “ ”/“ ” keys and press OK to commence upgrade. • Highlight “Edit upgrade” menu with “ ”/“ ” keys and press OK to change upgrade options. Please enter your available satellite information and save all values all select reset and press OK to re enter. Menu Locking Menu Lock In menu lock you can set locking for All Menus, or the Installation Menu to restrict access to these menu’s. If the menu lock is disabled, there will be free access to the menu system. Use “ ”/“ ” buttons to go to Menu Lock option. Use “ ”/“ ” buttons to choose Menu Lock Mode. DISABLED : All menus are unlocked. English - 15 - 01_S7100_[GB]_DVB660_1102UK_10075948_50201311.indd 15 28.11.2011 08:37:19 ALL MENUS : All Menus are accessible only with the correct lock key. So the user can’t add, delete, rename, channels, can’t set timers. Language INSTALLATION : Installation menu is locked. So the user can’t add channels. Changes will be updated after exiting ‘Configuration Menu’. Set Pin The PIN code of the unit changed. Use “ ”/“ ” buttons to go to “Set PIN” option. Press OK to display the “Set PIN” window. Use numeric buttons to enter new pin number. You will need to input your new pin a second time for verification purposes. If both pin numbers are four digits long and the same, the pin code will be changed. The factory default pin number is 0000. If you change the pin number, make sure you write it down and keep it safe for future references. Time Settings (Optional) • In the configuration menu, highlight the Time Settings item by pressing “ ” or “ ” buttons. • Press “OK” and Time Settings sub menu will be displayed on the screen. Current Time,Time Zone Setting and Time Zone will be available. ‘• Use “ ” or “ ” buttons to highlight the Time Zone Setting. Time Zone Setting is set using “ ” or “ ” buttons. It can be set to AUTO or MANUAL. • When AUTO is selected, Current Time and Time Zone options will not be available to be set. If MANUAL option is selected as the Time Zone Setting, Time Zone can be altered: • By pressing “ ” or “ ” buttons select Time Zone. Use “ ” or “ ” buttons to change the Time Zone between GMT-12 or GMT+12. Current Time on the top of the menu list will then change according to the selected Time Zone. Menu: shows the language of the system Note:These settings will be used if available. Otherwise the current settings will be used. • Audio: by pressing “ ” or “ ” keys change the audio language. • Subtitle: alter the subtitle language with “ ” or “ ” keys. The chosen language will be seen in subtitles. • Guide: By pressing “ ” or “ ” buttons change the guide language Recording configuration Select Recordings item in the Setup menu to configure recording settings. The following menu is displayed for recording configuration. HDMI HDCP In the Configuration Menu, highlight the HDMI HDCP item by pressing “ ” or “ ” buttons. Use the “ ” or “ ” buttons to set the HDMI HDCP as On or Off. Low Power Use “ ” or “ ” button to select Low Power and then press “ ” or “ ” button to set this setting as Yes or No. To save energy, Low power option should be selected as Yes. Automatic Power Down Press “ ” or “ ” button to select Automatic Power Down. Use “ ” or “ ” button to set the Automatic Power Down to Yes or No. If you don’t use STB for a long time, the box will switch off. The following options are available for adjustments: Auto discard Discard When the USB disk is full and a timer is set to record, the unit will automatically discard previous recordings based on this setting. The options are as follows: None: The unit will not discard any recordings and the timer will not record the requested programme. English - 16 - 01_S7100_[GB]_DVB660_1102UK_10075948_50201311.indd 16 28.11.2011 08:37:19 Oldest: Starting with the oldest, recordings will be deleted to make space for the requested timer. Internet Settings Longest: Starting with the longest, recordings will be deleted to make space for the requested timer. Shortest: Starting with the shortest, recordings will be deleted to make space for the requested timer. Unplayed: If this option is set to EXCLUDED, any unplayed recordings will not be deleted.If this option is set to INCLUDED, unplayed recordings will be deleted. Format Drive IMPORTANT: Note that ALL the data stored on the USB disk will be lost and then the disk format will be converted to FAT32 if you activate this feature. • If you want to delete all files on the connected USB hard disk drive or memory stick, you can use Format Disk option. • Also, if your USB disk malfunctions, you can try formatting the USB disk. In most cases, formatting the USB disk will restore normal operation; however, ALL the data stored on the USB disk will be lost in such a case. • Press OK button while the Format Disk option is highlighted. A menu will appear on the screen, requiring you to enter a pin number. If you have not changed the pin number, the factory default is 0000. After you enter the pin, a pop-up menu appears on the screen to ensure that the hard disk should be formatted, select “YES” and press OK to format the hard disk. Select “NO” and press OK to cancel. Ensure you back up important recordings before you format the USB disk unit. Max Timeshift : You can set timeshift duration by using this function Load Settings You use this item to load preset channel table or last saved settings, which had been loaded to receiver at the factory. To reload factory settings, highlight this item and press OK button. Then the following message will be displayed: “Are you sure to load default program tabel and settings?” You can confirm by pressing OK button or cancel by using MENU button. You can also cancel by highlightin NO and then pressing OK button. Save Settings You can use this item to load preset channel table or last saved settings as a factory settings. Highlight Save Settings line and press OK key, Then the following message will be displayed: “Are you sure to store current program table and settings as default?” You can confirm by OK button or cancel by MENU button. You can also cancel by highlightin NO and then pressing OK button. On Internet Settings window you can set IP address of the box. IP address can be either static or dynamic. In static option the address is manually entered. Also subnet mask and DNS Server’s IP addresses should be set correctly. If the IP address is not known or if a specific IP is not used, you can press BLUE (Dynamic) button. With this selection a new IP address is taken from service supervisor and addresses are displayed on this menu. If Dynamic is option is selected, IP information will be taken from the network. If Static option is selected, you should manually enter the IP address. This menu is functional if a connection is present and if the ethernet cable is plugged. If a connection problem occurs or the box does not connect, menu screen will display link status as Bad. To disable network, press RED and to check internet speed please press GREEN while a network connection is active. Note: These settings can be used only for software update. Recordings Library IMPORTANT: To view recordings library, you should first connect a USB disk to your set-top box while the set-top box is switched off. You should then switch on the set-top box to enable recording feature. Otherwise, recording feature will not be available. To view the list of recordings, press the MENU button to display the main menu and use the “ ” or “ ” button to highlight the “Recordings Library” line and press the OK button. Recordings Library will then be displayed with available recordings. English - 17 - 01_S7100_[GB]_DVB660_1102UK_10075948_50201311.indd 17 28.11.2011 08:37:20 To view Media Browser menu, please press MENU button on the remote control and select Media browser item by pressing “ ” or “ ” button. After press OK button, Media Browser screen will be displayed. All the recordings are kept in a list in the recordings library. BLUE button (Delete) :Erases the selected recording. P